AVR10 engelsk 11/01/98 10:10 Side 1 harman / kardon AVR 10 Power Headphones harman/kardon Service and Parts Office: 80 Crossways Park West, Woodbury, New York (800) 422-8027 8500 Balboa Blvd, Northridge CA 91329 A Harman International Company 1111-AVR10-1 Printed in Korea 230 Volt - 11 Language Version 9007017870 AVR10 engelsk 11/01/98 10:10 Side 2 AVR10 Volume Tune/Preset PRESET MEM Seek Stereo FM MHz Memory Tune/Preset VCR1 CD FM Bass Treble Balance Surround Off Surround Tape Mon TV/VCR 2 Aux AM VCR 2 harman/kardon Sintoamlificatore Audio/Video ·ÈÔÂÓÈÛ¯Ù<~ Audio/Video Audio-och videomottagare Audio- og videoreceiver Audio/videovahvistin ISTRUZIONI PER L'USO ¢°TM ÃTMTM §§¡ BRUKSANVISNING BRUGSANVISNING KÄYTTÖOPAS Audio Video Receiver Audio und Video Receiver Ampli-tuner audio/vidéo Receptor de audio y video Audio/video ontvanger Receptor de Audio/video OWNER'S MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DEL USUARIO GEBRUIKSAANWIJZING MANUAL DE INSTRUÇÕES AVR10 engelsk 11/01/98 10:10 Side 1 ENGLISH Harman Kardon AVR10 Date of purchase Purchased from Address of business purchased from Installed by Date Installed Serial No. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Thank you for choosing a Harman Kardon Audio/Video Receiver. Your new Unit is an exceptionally well-engineered product that will give you years of superb performance. Save all packing material. It is essential for shipping should you move, or in the event the unit needs repair. 1 AVR10 engelsk 11/01/98 10:10 Side 2 HANDLE THE POWER CORD GENTLY s To disconnect the plug from the AC outlet, pull on the plug itself, not on the cord. s Disconnect the plug from the AC outlet whenever the unit is to be left unused for an extended period of time. s Do not place furniture or other heavy objects on the cord, and avoid dropping heavy objects on it. Also do not make a knot in the cord. MOVING THE UNIT Before moving the unit, be sure to unplug the power cord from the AC outlet and disconnect all wires to antennas and other components. TABLE OF CONTENTS Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Surround Sound Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 AVR10 System Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ENGLISH DO NOT OPEN THE CABINET Do not attempt to service this unit. Tampering with internal components can cause fire or shock, and may void your guarantee. If water or a small object enters the unit, unplug the power cord immediately and consult an authorized Harman Kardon service center. Using the unit under such conditions may cause a fire or shock hazard. PLACE THE UNIT ON A FIRM AND LEVEL SURFACE Avoid installing it: s In moist or humid places s Close to heating equipment or in places exposed to direct sunlight s In a direct draft from an air conditioner or in other very cold locations s In places subject to excessive vibration or dust s In poorly ventilated places FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio TV technician for help. CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CLEANING Remove dust by wiping the unit with a soft, dry cloth. If necessary, use a soft cloth lightly dampened with mild soapy water; then wipe with a dry cloth. Never use benzene, thinner, alcohol or other volatile agents, and avoid spraying insecticides near the unit. 2 AVR10 engelsk 11/01/98 10:10 Side 3 Front Panel Controls 16 13 11 14 12 15 ENGLISH harman / kardon AVR 10 Tune/Preset Seek Stereo Memory Tune/Preset Volume PRESET MEM FM MHz VCR1 CD FM Bass Treble Balance Power Headphones Surround Off Surround Tape Mon VCR 2 TV/Aux AM VCR 2 1 2 7 6 9 8 3 4 5 10 3 AVR10 engelsk 11/01/98 10:10 Side 4 Front Panel Controls 1. POWER BUTTON Press this button to turn the power on. Press again to turn the power off (Stand by). If you connect the other components to the switched outlet, it can also be used as a system power button. 5.BALANCE CONTROL This control is used for balancing the relative sound volume of the left and right channel speakers. Clockwise rotation reduces the volume from the left speaker, counterclockwise rotation reduces the volume from the right speaker. 11. TUNE / PRESET UP/DOWN BUTTONS When PRESET and AUTO is not lit, the Tune/Preset UP/DOWN buttons will allow you to tune to a station manually. 14. SEEK STEREO BUTTON ENGLISH Press this button, "Auto" will illuminate in the display. Then press the uP or DOWN button. The tuner will automatically seek for stations upwards or downwards in your area that have enough signal strength to be listenable. The tuner will stop on stations until the Seek Stereo button is pressed again. 12. TUNE / PRESET BUTTON Press this Tune/Preset button to light up the preset mode then use the up/down buttons (11) momentarily to scan the preset station frequencies. The receiver stops at each preset location from 1-30 that has been entered in memory. Hold the buttons (11) down to skip through the presets quickly. In the TUNE mode (selected by the TUNE/PRESET button (12)) press these buttons to change selected frequencies. 2. HEADPHONE JACK Stereo headphones can be plugged into this jack for private listening. Headphone impedance should be between 8 ohms and 2K ohms with best results between 200 and 400 ohms. 6. SURROUND MODE SELECTOR Press this button to select the desired surround mode. The mode is changed between normal DOLBY Pro-Logic and DOLBY 3-STEREO. 15. VOLUME CONTROL Turn the VOLUME clockwise to increase the volume and counterclockwise to decrease it. The volume of the front, center, and rear channels is changed at the same time. 3. BASS CONTROL Modifies the low-frequency sound of the left and right channels as much as ±10dB. Set this control at a suitable position for your taste and room acoustics. 7. BYPASS SELECTOR Defeats all surround modes. 8. INPUT FUNCTION SELECTOR BUTTONS Press these buttons to select the desired input source. 16. DISPLAY WINDOW This window shows the state of operation for easier control of the receiver. It also contains the IR Remote Sensor. 13. MEMORY BUTTON Use this button to store an AM or FM frequency. Press this button and select one of 30 preset locations to store the frequency with the UP / DOWN buttons while the memory indicator blinks, press MEMORY again to store preset station. NOTE: When you store a frequency in a memory location that already contains a frequency, you replace the previous frequency. If your receiver is disconnected from AC power for more than about 2 weeks, it loses all stored frequencies. 4. TREBLE CONTROL Modifies the high-frequency sound of the left and right channels as much as ±10dB. Set this control at a suitable position for your taste and room acoustics. 9. TAPE MONITOR BUTTON Press this button to select input from a tape deck and listen to its monitor function (with 3 head decks). 10. VCR2 INPUT JACKS Connect these jacks to the corresponding output jacks of a VCR or Camcorder (only playback) (Yellow: Video, Red/White: Audio). 4 AVR10 engelsk 11/01/98 10:10 Side 5 Rear Panel Connections FM OUTDOOR ANTENNA ENGLISH AM LOOP ANTENNA FM INDOOR ANTENNA TV MONITOR CENTER SPEAKER 3 1 2 ANTENNA + - 10 300/75 ADAPTOR 300/75 ADAPTOR 13 AM LOOP LEFT RIGHT 17 16 VIDEO VCR 1 MAIN IN MONITOR CENTER SPEAKER (8) AC INPUT AC 230V~50Hz 450W AC OUTLET 16 REAR SPEAKERS 4W RIGHT LEFT SERIAL NO. FM 75 PRE OUT SUB WOOFER OUT IN OUT OUT 8 VCR 1 9 14 LEFT 12 REMOTE CONTROL LEFT MODEL NO.: AVR 10 HARMAN KARDON NORTHRIDGE CALIFORNIA U.S.A. 18 15 IN FRONT SPEAKER (8W) RIGHT SWITCHED MADE IN KOREA TOTAL 100W MAX AC 230V~50Hz RIGHT TV/AUX CD PLAY TAPE REC PLAY REC OUT (USE 8 OHM MIN SPEAKERS) + - + - + - - + 4 COMPACT DISC PLAYER 5 6 7 AUDIO VIDEO 11 REAR SPEAKERS TO 18 CASSETTE DECK IN REC IN PLAY OUT OUT OUT LEFT FRONT SPEAKERS VCR RIGHT TO WALL OUTLET 5 AVR10 engelsk 11/01/98 10:10 Side 6 Rear Panel Connections 1. FM INDOOR ANTENNA Connect the supplied antenna (the wire lead) to a 300/75 adapter and connect the adapter to the 75 T-shaped FM antenna terminal, as shown in the Rear Panel Connection Diagram. Change the position of the antenna until you get the best reception of your favorite stations. 3. AM LOOP ANTENNA Tune in your favorite AM station and position the loop antenna for best reception. Try other stations and find the position that gives the best overall reception. When this unit is mounted in a rack or placed on a shelf with sufficient space behind, hang the antenna on a wall in the direction which gives the best reception. NOTE: If noise is heard during AM reception, move the antenna for better reception. To prevent undesired noise, the AM LOOP ANTENNA should be located away from the remote control cord over 12 inches (30 cm). 4. TV / AUX INPUT JACKS This input is provided for any source you want to hear. An additional compact disc player, tape recorder, TV video cassette recorder (VCR), etc. can be plugged into these jacks (only for playback). 10. VIDEO MONITOR JACK Connect this jack to the VIDEO INPUT jack of a TV/MONITOR. ENGLISH 11. REMOTE CONTROL OUT JACK Connect this jack to the REMOTE IN jack on a Harman Kardon component. Use one of the accessory mini-plug cables. You can control many other Harman Kardon components in your system using the AVR 10 remote commander. 5. CD INPUT JACKS Connect the output cables of a compact disc player to these jacks. 2. FM OUTDOOR ANTENNA An outdoor FM antenna may be used to further improve the quality of reception. Disconnect the indoor antenna before replacing it with the outdoor one. A 75/300 adaptor must be used only, if your antenna system has no 75 coaxial cable. 6. TAPE PLAY JACKS Connect the line output of your CASSETTE DECK to these jacks. 7. TAPE REC JACKS Connect the line input of your CASSETTE DECK to these jacks. 12. MULTI-ROOM REMOTE IN JACK Connect a Harman Kardon HE 1000 remote IR sensor to this jack. You can operate the unit by remote commander through the adaptor. It is convenient when the unit is located in a separate room. 8. VIDEO / AUDIO INPUT (PLAY) JACKS OF VCR1 AM LOOP ANTENNA SETTING Connect these jacks to the corresponding OUTPUT jacks of your VCR. 9. VIDEO / AUDIO OUTPUT (REC) JACKS OF VCR1 Connect these jacks to the corresponding INPUT jacks of a VCR. VIDEO VCR1 OUT jack: Connect this jack to the VIDEO INPUT jack of the VCR. VCR1 REC jack: Connect these jacks to the AUDIO INPUT jacks of the VCR. LEG Stand and place it on a shelf or hang it on a wall. 13. FRONT PRE OUT AND MAIN IN JACKS Pre Out When a separate power amplifier is used to drive the front speakers, connect the power amplifier input to these jacks (see page 8). 6 AVR10 engelsk 11/01/98 10:10 Side 7 Main In When a separate pre-amplifier is connected and this unit is used as a power amplifier, connect the preamplifier output to these jacks. NOTE: When you do not use the PRE OUT and MAIN IN separately, always connect the PRE OUT and MAIN IN jacks with the jumper plugs. ENGLISH 16. CENTER/REAR SPEAKER TERMINALS Connect the center and rear speakers to the corresponding terminals. Make sure that the positive (+ or red) and negative (- or black) terminals on the speakers are connected to the corresponding terminals on the receiver. When you connect the rear speakers, connect both L and R speakers. PLEASE NOTE: Sound will not be provided through the rear speakers unless both speakers are connected. 14. SUBWOOFER OUTPUT JACKS Connect a powered subwoofer to these jacks. This output may also be used for any external component requiring a full range volume level input. 17. AC INPUT CORD Plug this cord in AC outlet on a wall. 15. SPEAKER TERMINALS Connect the front left (L) and right (R) speakers to the corresponding terminals. Make sure that the positive (+ or red) and negative (- or black) terminals on the speakers are connected to the corresponding terminals on the receiver. 18. AC SWITCHED OUTLET These outlets provides AC power. The AC power is switched by the power button of this receiver. Use this outlet for a CD player or a cassette deck. 7 AVR10 engelsk 11/01/98 10:10 Side 8 WHEN YOU DRIVE THE FRONT SPEAKERS WITH ANOTHER AMPLIFIER ENGLISH (Remove PRE-OUT/MAIN IN jumpers when the front speakers are connected to external amplifier.) CENTER SPEAKER + LEFT RIGHT - MAIN IN CENTER SPEAKER (8W) PRE OUT SUB WOOFER OUT LEFT REAR SPEAKERS RIGHT LEFT FRONT SPEAKER (8) RIGHT (USE 8 OHM MIN SPEAKERS) LINE-INPUT L R Power FRONT(left) FRONT(right) + - + - 8 AVR10 engelsk 11/01/98 10:10 Side 9 WHEN YOU DRIVE THE SUBWOOFER AMP ENGLISH FRONT SPEAKERS CENTER SPEAKER + LEFT RIGHT - + - + - MAIN IN CENTER SPEAKER (8) PRE OUT SUB WOOFER OUT LEFT REAR SPEAKERS RIGHT LEFT FRONT SPEAKER (8W) RIGHT (USE 8 OHM MIN SPEAKERS) LINE-INPUT L R SUBWOOFER AMP 9 AVR10 engelsk 11/01/98 10:10 Side 10 Surround Sound Effects SURROUND PROCESSING Dolby 3 Stereo (3 channel mode) Combines the front and rear signals so that you can enjoy a regenerated sound field which has comparatively more presence and a more expansive feeling from the front 3 channels (front L, front R, center speaker) than that of ordinary stereo regeneration. Dolby Pro Logic Surround A great number of movies made in recent times have the sound track specially encoded with the Dolby Surround Mode (carrying the [Dolby Stereo] or [Dolby Surround] trademark*). The front speakers provide the dialogue and the normal stereo effect, while the rear speakers reproduce the surround signals. This mode provides excellent results when watching television programs, video software, video discs or video tapes of stereo television broadcasts encoded with Dolby Surround. Dolby Stereo films have dramatically changed the role of the movie-goer from that of observer to that of participant. Clearer dialogue, richer music, enveloping ambience and making high-fidelity, multi-dimensional sound are essential parts of cinematic presentations. Imagine recreating the same sort of audio-visual experience right in your own home. *Manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby", "Pro Logic" and the double D symbol are trademarks of Dolby Laborities Licensing Corporation. CENTER FRONT(left) FRONT(right) ENGLISH SPEAKER INSTALLATION The AVR 10 incorporates a decoder which reproduces the specially encoded surround sound of Dolby Surround video programs. In Dolby Surround mode, select the speaker operation mode which best suits your speaker system,: 3 STERO mode Select this mode when you play back a Dolby Surround program or a normal Stereo source only with the front and center speakers. The sound of the rear channels is output from the front (L and R) speakers. 10 AVR10 engelsk 11/01/98 10:10 Side 11 CENTER CENTER FRONT(right) FRONT(left) FRONT(right) FRONT(left) FRONT(right) ENGLISH FRONT(left) REAR(left) REAR(right) REAR(left) REAR(right) REAR(left) REAR(right) WIDEBAND mode Select this mode if you use a center speaker big enough for reproducing all bass frequencies. PHANTOM mode Select this mode when you play back a Dolby Surround program source without using a center speaker. The sound of the center channel is redirected to the front (L and R) speakers. NORMAL mode Select this mode if you use a medium to small center speaker. The bass sound of the center channel is output from the front speakers, as a small speaker cannot produce enough bass. 11 AVR10 engelsk 11/01/98 10:10 Side 12 Operation BASIC OPERATION 1. Press the POWER button to ON. The display panel will light up. Note: If you prefer to turn the unit off and on with the remote control, this button must be left in the ON position. The remotes Standby button will then turn the unit "ON" and "OFF" by taking it in and out of standby mode. 2. Select the desired program source with the INPUT FUNCTION SELECTOR buttons. The selected input function will appear in the display. 3. Operate the selected component for playback. · When a video source is selected, the picture will appear on the television and sound will be heard from the speakers. · When playing back a video source with surround sound effects, refer to the "Surround Sound Effects" of this manual. · When the TAPE MONITOR button is set to ON so that the TAPE MONITOR indicator lights up, selected program sources other than TAPE cannot be heard from the speakers. To listen to a program source other than cassette deck be sure to set the TAPE MONITOR button to OFF. 4. Adjust the volume to a comfortable listening level with the VOLUME control or MASTER VOLUME UP/DOWN buttons on the remote control. 5. For private listening, insert a 6,3 mm plug of the headphone into the HEADPHONE jack. · When the headphones are plugged in, sound from the speakers is cut off. MANUAL TUNING Auto tuning may not be possible if the broadcast signal is weak. If so, use manual tuning. 1. Press the FM or AM button to select the desired band. 2. Press SEEK STEREO to delete the AUTO in the display. 3. Press the UP or DOWN TUNE/PRESET button until the desired station frequency is reached. · Each time the button is pressed, the frequency changes by a step. · When the button is kept pressed, the frequency changes continuously in sequence. MANUAL PRESETTING ENGLISH Up to 30 stations can be preset at random, regardless of the reception band. 1. Tune in the station to be stored in memory using the auto or manual tuning. 2. Press the MEMORY button. The MEMORY indicator will light up for 5 seconds. 3. Select the preset number with the UP or DOWN TUNE/PRESET button or the numeric buttons on the remote while the MEMORY indicator is lit. 4. Press the MEMORY button to store the station. · When using the NUMERIC buttons on the remote, the station is stored in memory without pressing the MEMORY button again. · When selecting single digit preset numbers with the NUMERIC buttons on the remote, press the corresponding number without pressing "0" first. 5. Repeat steps 1 to 4 to preset other stations. LISTENING TO BROADCASTS Press the AM or FM button and use auto, manual or preset tuning to select a radio station. AUTO TUNING If broadcast signals are strong enough, auto tuning is possible. 1. Press the FM or AM button to select the desired band. 2. Press the Seek Stereo button so that AUTO lights up in the display. 3. Press the UP or DOWN TUNE/PRESET button. Tuning will start automatically and stop at a broadcast station frequency with sufficient signal strength. PRESET TUNING The receiver has a memory for up to 30 preset stations. If the station frequencies are stored in this memory, they can be tuned in by a simplified procedure: 12 AVR10 engelsk 11/01/98 10:10 Side 13 ENGLISH RECALLING THE PRESET STATIONS Select the preset number of the desired preset station with the UP or DOWN TUNE/PRESET (in the PRESET mode) or NUMERIC buttons on the remote control unit. · In the event of a power failure or when the receiver is disconnected from the AC outlet, the memorized stations are maintained for approximately 2 weeks. DUBBING FROM VCR2 TO VCR1 1. Press the VCR2 INPUT FUNCTION SELECTOR button and play back on the VCR connected to VCR2. The video and audio signals from VCR2 will be dubbed auto VCR1. 2. Start recording on the VCR connected to VCR1. RECORDING WITH A CASSETTE DECK 1. Select the program source to be recorded with the INPUT FUNCTION SELECTOR buttons. 2. Start recording on the cassette deck. 3. Play back the desired program source and start recording on the cassette deck. · The volume, balance, bass and treble settings have no effect on the recording. · When recording is performed on a 3-head cassette deck, the recorded sound can be monitored through the speakers by pressing the TAPE MONITOR button to ON. SCANNING THE PRESET STATIONS IN SEQUENCE 1. Press the PRESET SCAN button on the remote control unit to listen to a brief sample of each preset station. 2. The receiver will start scanning the stations in the preset sequence and each station is received for 4 seconds. 3. At the desired station, press again to stop scanning. NOTES: · If the end of the frequency range is reached during the auto or manual tuning, tuning will continue from the opposite end. · When FM stereo broadcasts are poor, select the FM mono mode with the SEEK STEREO button so that the AUTO indicator goes off. · When storing a new station preset, the previously memorized station on the same preset is cleared. RECORDING WITH SEPARATE VIDEO AND AUDIO SOURCES When dubbing from VCR2 to VCR1, you can replace the audio signal from VCR2 with the audio signal from other program sources. 1. Press the VCR2 as a video source to be recorded. 2. Select the audio source (CD, TV/AUX, FM/AM) to be recorded with the INPUT FUNCTION SELECTOR buttons. 3. Start recording on the VCR connected to VCR1. 4. This allows you to watch the picture from the video component on the television and listen to the sound from the audio component through the speakers while recording. NOTE: Be sure to observe the order of steps 1 and 2. 13 AVR10 engelsk 11/01/98 10:10 Side 14 AVR10 System Remote Control 1. INFRARED TRANSMITTER WINDOW The infrared beam is emitted forward from this window when you press any button on the commander. For the remote controls to function properly, always face this window toward the remote sensor window on the receiver and do not obstruct this window with any material. 5. NUMERIC BUTTONS These buttons can be used for preset tuning in TUNER mode. Preset tuning: Select one of 30 preset locations by pressing the numeric buttons directly, thereby the input of the receiver automatically is changed to TUNER. achieve the best surround sound effect. For Dolby Surround sound, we recommend a 20ms delay. The delay time is changed as below, when the button is pressed in succession. 13. REAR LEVEL UP/DOWN BUTTONS These buttons operate only in Dolby PRO LOGIC mode. Use these buttons to adjust the sound level of the surround speakers. Set the MASTER VOLUME control at the desired level and press the REAR LEVEL up or down button until you get the optimum surround effect at your listening position. ENGLISH DOLBY PRO LOGIC MODE 15 ms 20 ms 25 ms 30 ms 6. CD FUNCTION BUTTONS For a CD PLAYER: DISC (DISC SELECTOR is available for the Harman Kardon FL8400, FL8450CD changer), PLAY, PAUSE, STOP, BACKWARD SEARCH, FORWARD SEARCH, A-B and INTRO buttons are available. When selecting a disc, press the DISC button. 2. STANDBY BUTTON Press this button to turn the power on and off. NOTE: For the Standby Button to work, the power switch on the AVR 10 must be set to ON. Automatic power on: When you press the input function buttons (CD, TUNER, TAPE, TV/AUX, VCR1, VCR2) in STANDBY mode, the power is automatically turned on and the function is selected. 9. INPUT FUNCTION SELECTOR Press the button to select the desired input function. The available buttons are CD, TUNER, TAPE MON, TV/AUX, VCR1, and VCR2. 14. MASTER VOLUME BUTTONS Adjust the overall (Front, Center, and Rear) volume level. 10. CENTER LEVEL UP/DOWN BUTTONS Use these buttons to adjust the sound level of the center speaker to that of the front speakers. These buttons work only in Dolby Pro Logic and Dolby 3 Stereo mode. These buttons do not work in PHANTOM mode. 15. DISPLAY BUTTON Press once and the display dims, press again and it turns off. Press a third time and it goes on. 7. CASSETTE DECK FUNCTION BUTTONS For a cassette deck: PAUSE/RECORD, STOP, REVERSE PLAY, FORWARD PLAY, REWIND, FAST FORWARD buttons are available. 16. SLEEP BUTTON Set the receiver to automatically turn off after 10, 20, 30, 60, or 90 minutes. Each time the button is pressed, the setting is advanced as below. 15 ms 20 ms 25 ms 30 ms 3. TUNING UP/DOWN Press these buttons to tune the receiver up or down. 4. PRESET SCAN BUTTON Button for scanning preset station frequencies (see page 13). 8. DELAY TIME BUTTON This button operates only in Dolby Pro Logic mode. In this mode the output signal from the surround speakers is delayed slightly from that of the front speakers. Select appropriate delay time to 11. CENTER MODE BUTTON Selects the center mode (see page 11). 12. TEST TONE BUTTON Generates test sounds in all channels (Left, Center, Right and Surround) in succession. The display will dim when the sleep function has been set. 14 AVR10 engelsk 11/01/98 10:11 Side 15 17. MUTE BUTTON ENGLISH Press this button to silence the speakers temporarliy. The volume indicator blinks. Press again to restore the same listening level as before. 18. BATTERY COMPARTMENT This battery case is provided as the power source for the commander. To 5 CD Tuner remove the cover, press it down with your thumb and pull it towards the back side. Two UM-3, size "AA" or R6 1.5V dry batteries are used. When loading the batteries, make sure that the polarity is correct. Remove the batteries from the case if the remote commander will not be used for a long time. 1 harman kardon 3 Standby Tuning PScan 1 2 / ON 4 2 7 3 8 4 9 5 0 1 6 Disc Search Skip 6 Intro harman / kardon AVR 10 Tune/Preset Seek Stereo Memory Tune/Preset Volume CD Tuner A-B PRESET MEM FM MHz Tape Mon Cass Deck 9 VCR1 CD FM Aux Select A/B 7 Bass Treble Balance VCR 1 VCR 2 VCR 2 Power Headphones Surround Off Surround