2.0 Processor/Tuner Owner's Manual Owner's Manual Signature 2.0 Processor/Tuner Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2­3 Unpacking and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Quick Start Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5­7 Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8­9 Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10­11 Remote Control Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 12­15 Remote Control Programming . . . . . . . . . . . . . . . . . . . . . . . 16­18 System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19­21 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22­26 Source Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27­31 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32­34 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35­51 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52­54 Appendix A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Appendix C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57­61 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62­63 Figure Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Subject Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 80 Crossways Park West Woodbury, NY 11797 www.harmankardon.com ©1997 Harman Kardon, Incorporated Staple or clip your original invoice here. ¤ Signature 2.0 Congratulations! With the purchase of a Harman Kardon Signature Series product you are about to begin many years of listening enjoyment. The Model 2.0 Processor/Tuner has been designed to provide all the excitement and detail of motion picture soundtracks and reproduce every subtle nuance of your favorite musical selection. On-board Dolby* Digital decoding enables the 2.0 to deliver six channels of fully discrete sound from today's DVD releases and tomorrow's HDTV broadcasts, while a wide selection of matrix decoding modes delivers full compatibility with conventional Dolby Surround stereo and mono programs. The 2.0 is also ready to accept future surround systems through the use of sixchannel direct inputs that accommodate optional outboard decoders for future surround systems. the meaning of the on-screen and front panel display messages will enable you to take advantage of all the power the Signature 2.0 is able to deliver. Harman Kardon has been a part of the audio world since it invented the first high-fidelity receiver over fortyfive years ago. With the combination of state-of-the-art circuitry and time honored design philosophies, the Signature 2.0 is one of the most innovative products ever offered by Harman Kardon. Should you have any questions about this product, its operation or installation that are not answered in this manual please contact your retailer or custom installer. They are your best source for product information. You may also contact Harman Kardon via the World Wide Web at www.harmankardon.com Introduction 2.0 DVD Standby Vol 10 Tune Mute Dolb y Di g ital Source Surround On/Off While complex digital circuits are hard at work within the 2.0, a simple on-screen menu system and learning remote control make the unit easy to install and operate. In addition to selecting from a variety of audio/video sources, the Signature 2.0 is equipped with the latest in tuner technology, including the RDS data system that automatically identifies FM stations transmitting special data and provides information they transmit about the station's programming. The RDS system even lets you automatically search for a station with a specific program type from the participating stations in your reception area. To obtain maximum benefit from the Signature 2.0's many features we urge you to take a few minutes to read through this manual. That will ensure that connections to playback sources, power amplifiers and other external devices are made properly. In addition, a few minutes spent learning the functions for the various controls and 1 The following are among the 2.0's many features: s On-Board Dolby Digital Decoding s Multiple Coax and Optical Digital Inputs s Composite and S-Video Switching s Easy-To-Use On-Screen Menu Control System s FM Stereo/AM Tuner With RDS Data System and 30 Presets s Learning Remote Control Pre-Programmed With Harman Kardon and RC-5 Control Codes s Trigger Output For Automatic Control of Signature Series Power Amplifiers s RS-232 Control Port For Connection To External Automation Systems s Six-Channel Direct Inputs For Use With External Audio Adapters or Decoders. Signature 2.0 Important Safety Information Verify Line Voltage Before Use This Signature 2.0 has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard, and may damage the unit. If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet. CATV or Antenna Grounding If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (Cable TV) system installer's attention to article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible. Safety Information Do Not Use Extension Cords To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately with cords meeting factory specifications. Installation Location s To assure proper operation, and to avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product. s Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances a fan may be required. s Do not place the unit directly on a carpeted surface. s Avoid installation in extremely hot or cold locations, or an area that is exposed to direct sunlight or heating equipment. s Avoid moist or humid locations. s Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them. Handle the AC Power Cord Gently When disconnecting the power cord from an AC outlet, always pull the plug, never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet. Do Not Open The Cabinet There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or a staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service station. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. 2 Signature 2.0 Cleaning When the unit gets dirty, wipe it with a clean, soft dry cloth. If necessary, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit. NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment. Unpacking and Installation The carton and shipping materials used to protect your new 2.0 during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move or should the unit ever need repair. To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton down to a more two-dimensional appearance. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag. If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center. Safety Information Moving The Unit Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet. Important information for the user NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s Reorient or relocate the receiving antenna. s Increase the separation between the equipment and receiver. s Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. s Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. 3 Typographic Conventions In order to help you use this manual with diagrams of the remote control, front panel controls, rear panel connections and on-screen menus, certain conventions have been used. Example ­ (bold type) indicates a specific remote control or front panel button, or rear panel connection jack Example ­ (OCR type) indicates a mess ...