User manual HASBRO IDATEN JUMP BIG JUMP CHALLENGE

AGES 6+ 77113/77026 Asst. Big Jump Challenge TM* TO ASSEMBLE: Apply labels as shown. Snap parts together as shown. TO REASSEMBLE LAUNCHER: With launcher facing away from you, hold engine so that the metal gear is at the top of the right side. Tilt engine so that the hook on the launcher fits into the hole on the engine. Press engine down into launcher. 1 2 Place launcher top back on launcher so that it is flush with the body of the launcher. 3 Lock launcher top in place with the plastic ring by placing ring over tabs and turning it 90 degrees. 4 Reattach handle by inserting into hole so that slots and tabs match up, and turning counterclockwise to lock in place. SETTING UP: 1 For the Jump Distance Challenge Place the ramp on the white end of the mat. Lay the cardboard mat flat on the floor. 2 Set up on wood, tile or linoleum floors for the best performance of your bikes. Deep pile carpets can create an uneven play surface. 3 Place your launcher directly in front of the jump. 4 Take turns jumping your bikes as far as you can. Whoever lands on the highest scoring section of the mat wins! Race for Speed! Set up a finish line on the floor using string, or just the threshold between two rooms. You and a friend (or a bunch of friends) should line up next to one another, with your launchers at the ready. See who can beat the others to the finish line! Race for Distance! Line up and launch! Race your bikes to see who can go the farthest, the fastest! For the High Jump Air Challenge 1 Fold on the creases just below the 10 Point box and just below the word jump to form a three-sided box with Jump at it's top, as shown. 2 Fold the triangular flaps with the numbers on them in so that their edges face the box. 3 Fold the jump posts up so that the numbered flaps lock onto the sides of the mat at the bottom of the other sides of the jump posts. The tabs near the bottoms of the triangular flaps should hold onto the mat so that the posts do not unfold. 4 Reach into the box and push the rectangular tab in the wide white section through the slot in the white end of the mat. 5 Place the jump post at the desired level. 6 Place the ramp so that the end of the ramp is up against the top of the box. 7 Place your launcher directly in front of the jump. 8 Take turns jumping your bikes as high as you can. See if you can jump the bar set to level 4! TO PLAY: 1 Holding launcher steady and flat on floor by gripping the handle, insert the ripcord with teeth facing down. 2 Lock bike into launcher. 3 4 When you're ready to launch, pull the ripcord all the way out and press the button on the handle. The bike will speed away from you! Rev up the bike by moving the ripcord in and out. Look for: WHEEL TYPES: idATen JumPTM Ripcord Racers have different kinds of wheels. How a bike performs depends on what kind of wheel it has. Stunt Wheel ­ grips the surface of a ramp to launch into the air! Stability Wheel ­ extra weight keeps the bike moving fast even on long distance rides! Race Wheel ­ made for short, high-speed races! each sold separately. Stunt Ramps Collect them all! PoiSon FAngTM - with Race Wheel! FLAme KAiSeRTM - with Stunt Wheel! iRon HAmmeRTM - with Stability Wheel! nePTune emPeRoRTM - with Stability Wheel! AeRo SciSSoRSTM - with Stunt Wheel! THundeR KingTM - with Race Wheel! * Not suitable for children under 3 years because of small parts, choking hazard. Product and colors may vary. ®* and/or TM* & © 2006 Hasbro. All Rights Reserved. TM & ® denote U.S. Trademarks. ©TOSHIHIRO FUJIWARA-TOMY-KODANSHA/Aniplex-MN-TV TOKYO P/N 6590120000