Congratulations. You have purchased a Hayes Disc Brake system. This Manual is intended to provide the information necessary for normal maintenance and service of the Hayes Disc Brake system. Although the steps and procedures are relatively simple, they should not be attempted until you are thoroughly familiar with the entire set of procedures. Images have been provided to help you in the steps and procedures. TM SAFETY INFO Warning: As a serious rider you are well aware of the need to practice safety in all aspects of the sport. This includes service and maintenance practices as well as riding practices. Before each ride, always check your brakes for proper function and the brake pads for wear. When you ride, always wear a helmet. Warning: When you need to install any of the disc brake components, that installation work should be done by a qualified technician with the proper tools. Improper installation could cause severe or fatal injuries. Warning: This brake has been designed for use on a single person mountain bike. The use on any other vehicle or device will void the warranty and can cause serious injury. Warning: With use, disc brake components may become very hot. Always allow components to cool before attempting to service your bike. Warning: When following any of the procedures below, be sure to keep your hands and fingers from getting caught in the disc. Failure to do so could result in injury. Warning: For riders using the brakes in downhill conditions, it is recommended that you use the 8" disc version of the Hayes Brake. Not all frames and forks will accept and 8" disc. Please check with your frame or fork manufacturer or www.hayesdiscbrake.com for 8" disc compatibility. Consistently using the 6" disc in downhill conditions may cause the brake fluid to boil. HYDRAULIC DISC BRAKE INSTALLATION, SERVICE, MAINTENANCE MANUAL 45-17692Web CAUTIONS, WARNINGS, NOTES, ETC Within this manual are specifically labeled comments intended to bring special attention to a general procedure or detailed step. Be aware of, and understand, the meaning of these labels. Warning: Means that there is the possibility of personal injury to you or to others. Caution: Means that there is the possibility of damaging the brake or the bike. Note: Provides general information. Hint: Provides information that can help you properly complete a specific procedure. STARTING OUT Personal Preference and Adjustment In most cases, the Hayes Disc Brake system has been pre-assembled for your bike. However there are a couple of adjustments that you can make to match your particular physical characteristics or personal preferences. · Positioning the Master Cylinder and Lever 1. 2. 3. Loosen, but do not remove, the handle bar clamp screw Then, position the Master Cylinder and Lever on the handlebar in your desired position. Torque the handlebar clamp screw to 15-20 in-lbs (1.7-2.26 Nm) · Power Adjustment Dial (Figure 1) Adjusting the amount of power the brake provides can be done by turning the "Power Adjustment Dial". Turning the dial clockwise will reduce the amount of power the brakes provides. Turning the dial counter clockwise will increase the power the brake provides. Warning : DO NOT attempt to force the "Power Adjustment Dial" beyond its limits. Note: When adjusting the "Power Adjustment Dial" it will change the lever reach. Follow the instructions to set your lever reach. · Lever Reach Adjustment (Figure 1) Adjust the brake lever reach by turning the reach adjustment knob. Turning the knob counter clockwise will adjust the lever closer to the handle bar. Turning the knob clockwise will adjust the lever farther from the handle bar. Warning : Do not attempt to force the adjustment screw beyond its limits. Warning : Due to the different diameters of grips and twist shifters, DO NOT adjust the reach adjustment screw too far counter clockwise. Doing so could allow the lever blade to contact the grip, which may reduce braking power. · Caliper Hose Routing (Figure 1) The banjo on the caliper can be rotated to accommodate your frame or fork. Loosen the banjo bolt ¼ turn and rotate the banjo to the desired location. (Note: loosening the banjo bolt more than ¼ turn may introduce air in the system). Tighten the banjo bolt to 60 +/- 5 in/lb (6.7 +/- .5 Nm). Burnish Disc brakes require a special burnish period to achieve maximum braking power. This burnish period will last for about 30-40 stops. During this period some noise may occur. Recommended Fluids and Lubricants Use only DOT 3 or DOT 4 brake fluid. Do not use any petroleum-based lubricants, as this will cause the rubber parts to swell. Hayes recommends the use of DOT 3 or DOT 4 brake fluid. Clean the disc and pads only with isopropyl alcohol. INSTALLATION If you have purchased a bike new ­ with Hayes disc brakes already installed, you will not immediately be required to follow all of the following procedures. A. Tools Required Torx T25 driver Open-end wrenches; 6mm, 8mm, 9mm Scissors or cable cutters Torque Wrench Small Phillips screwdriver Small flathead screwdriver Allen Drivers: 2.5mm, 4mm, 5mm Hayes Caliper Bore Plug Tool B. Mounting the Disc to the hub (Figure 2) Note: Mounting the brake disc to the wheel is a simple matter, but one that requires care. If the wheel has to be rebuilt, have it done by a qualified technician using a 3 cross spoke pattern. We recommend the use of steel, quick release skewers only. 1. Clean the disc and hub mounting surface with isopropyl alcohol (not disc brake cleaners). 2. Place the disc on the hub mounting surface. Be sure that the arrow on the disc is pointing in the same direction as that of the forward wheel rotation. 3. Using a Torx T25 driver, install, tighten, and torque the disc screws to 50 +/- 5 in-lb (5.65 +/- .55Nm), in a star pattern sequence. C. Mounting the Caliper to the Frame or Fork Warning: When following any of the procedures below, be sure to keep your hands and fingers from getting caught in the disc. Failure to do so could result in injury. 1. Remove the wheel(s). 2. For some installations it will be necessary to mount a mount bracket to accept the Hayes Disc Brake caliper. Mount the mount bracket to the frame or fork using (2) M6 x 1.0 /18.4mm long mount bolts. Torque the bolts to 110 in-lbs (12.43 Nm). 3. Mount the caliper to the frame or mount bracket using (2) M6 x 1.0 / 18.4mm long mount bolts and (2) mount washers. Snug the bolts, but leave them loose enough so that caliper will move on its slots. Caution: For Manitou forks you will need to use (2) M6 x 1.0 / 22mm long mount bolts. These bolts are supplied in your aftermarket kit or supplied from the bike manufacture. Failure to use the longer bolt may result in fork damage that will not allow you to tighten down your caliper properly. Caution: For Manitou forks, torque the mounting bolts to 80 in-lbs (9,0 Nm) . 4. Re-install the wheel(s). 5. Squeeze and hold the brake lever. While holding the brake lever, shake the caliper to position it in its natural centered position over the disc. While squeezing the lever, tighten the mounting bolts. Warning: Do not adjust the caliper while the caliper is hot. Warning: Do not adjust the caliper while the wheel is spinning. 6. Release the lever, spin the wheel. Check that it spins freely and that the gaps, between the pad and the disc, are equal. If the gaps are unequal, or if there is drag, readjust the caliper position by loosening the mounting bolts and adjusting the caliper as needed. Hint: A white piece of paper can be used as a background to help sight down the disc looking for equal clearance between the pads and disc. 7. When the gaps are equal and the wheel spins freely (without drag), torque the mounting bolts to 110 in-lbs (12.43 Nm). Caution: For Manitou forks, torque the mounting bolts to 80 in-lbs (9,0 Nm) . 8. Repeat above procedure for other wheel. SERVICE A. Hose Removal and Assembly The follow procedures are to be used when replacing or removing the hose. · Master Cylinder Hose Removal (Figure 5) 1. To take the hose off of the master cylinder end, slide the nose cone down the hose. 2. Using a 8mm box wrench, remove the hose nut and slide it all the way down the hose. Note: sometimes it is best to first cut the hose and use the box end of the 8mm wrench to better grab the 8mm hose nut. 3. Slide the hose out of the end of the master cylinder. There will be some residual fluid in the hose and master cylinder / caliper. Be careful to avoid spilling that fluid. 4. A new hose insert/compression bushing combination will be needed each time the hose is re-installed. Remove the old compression bushing and hose insert by cutting the hose next to the compression bushing. The cut needs to be clean with no frayed ends. · Master Cylinder Hose Assembly 1. 2. 3. 4. 5. Locate the end of the hose without the permanent crimp. Cut the hose to the desired length with good scissors or cable cutters. The cut end must be clean and perpendicular to the hose itself. Slide the nose cone onto the master cylinder side of the hose. Slide the hose nut over the hose. Push the longer end of the barbed hose insert/compression bushing combination into the end of the hose. Be sure it is inserted flush with the end of the hose. Always use a new hose insert/compression bushing combination . 6. Slide the hose into the master cylinder and install the hose nut. Be sure that the hose is inserted completely into the master cylinder end. Be sure the hose remains inserted while tightening. 7. Using a 8mm open-end wrench, torque the hose nut to 70 +/- 5 in/lb. 8. Bleed the system · Caliper Hose Removal (Figure 5) 1. To take the hose off the caliper end, remove the banjo bolt using a 4mm Allen wrench. 2. When removing the banjo assembly completely from the caliper, be sure that the two banjo o-rings are not lost. Note: The end of the El Camino caliper hose is a permanent crimp. Therefore the connection cannot be trimmed to size or repaired. Shortening of the hose must be done at the master cylinder end. If the caliper hose connection is damaged, the hose must be completely replaced with a new hose with a permanent crimp attached. · Caliper Hose Assembly 1. Install the banjo bolt through the banjo. Be sure that there is a banjo o-ring on each side of the banjo. 2. Position the angle of the banjo to your desired location for your frame or fork. 3. Tighten the banjo bolt to 60 +/- 5 in/lb (6.7 +/- .5 Nm). B. Bleeding Air trapped in the hydraulic system of the disc brakes can decrease performance of the system and should be removed by "bleeding" the system and replenishing the system with new brake fluid. The system is filled by pumping fluid from the lowest point (at the caliper), through the system, to the highest point, the bleeder on the master cylinder. Caution: Use only new DOT 4 or DOT 3 brake fluid from a closed,sealed container. Use of any other fluid can cause the rubber parts to degrade and cause the brake to fail. Caution: DOT 4 or DOT 3 brake fluid will strip paint. Use extreme caution to avoid getting DOT 4 or DOT 3 brake fluid on paint. If DOT 4 or DOT 3 brake fluid comes in contact with paint, wipe it off immediately and rinse with isopropyl alcohol. Warning: If you get any brake fluid on the brake pads, discard them and replace with new pads. If you get any brake fluid on the disc, clean it thoroughly with isopropyl alcohol. Warning: DOT 4 and DOT 3 brake fluid can be an irritant when it comes into contact with human tissue. For skin contact, brake fluid should be washed off in flowing water. For eye contact, the eye area should be irrigated with flowing water immediately and continuously for 15 minutes. Consult with medical personnel. If effects occur from inhaling brake fluid fumes, move to an area with fresh air. Consult a physician. If brake fluid is ingested, induce vomiting and consult medical personnel. Used brake fluid should be disposed of in accordance with local laws. · Bleed Kit Assembly (Figure 4 C) 1. Screw the cap onto the end of the bottle. 2. Cut a 2" section of hose 3. Push the short section of hose over the cap until it slides past the ridge on the cap 4. Push the long section of hose into the master cylinder bleed fitting. NOTE: There are three fittings with the kit. The black plastic fitting is to be used with the "El Camino". · Bleeding the System 1. Remove the wheel. 2. Remove the brake pads so that any spilled fluid does not contaminate the pads. (See "Maintenance" instructions for pad removal) 3. Push the caliper pistons all the way into their bores using the box end of a 9mm end wrench. Caution: Don't push on the post in the center of the piston because that will bend the post. 4. Position the bike in a stand so that the brake caliper bleeder screw is perpendicular to the ground, and the reservoir bleeder screw on the master cylinder is the highest point on the brake system. NOTE: For the "El Camino" the bike should remain hor ...