COLOUR MONITOR FARBMONITOR MONITOR EN COLOR MONITOR A COLORI MONIIEUR COULEUR CM1484ME 141vlvxPliA USER MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . page BEDIENUNGSANLEITUNG MANUAL DEL USUARIO ................ .= . . . . . . . . . . ..m. seite pAgina 2 10 18 INSTRUZIONI PER L'USO . . . . . . . . . . . . . . . . . . pag 24 MANUEL DE L'UTILISATEUR . . . . . . . . . . . . . . page 30 I . NOTICE The information in this document is subject to change without notice. Hitachi assumea no responsibility for any errors that may appear in this document. Colour Monitor 14MVX Plus Operating Guide Features: The following features are provided with the HITACHI colour Monitor 14MVXPhS: Wide compatibility range of graphics standard, VGA, XGA, 8514/A, Super VGA, and Macintosh lIVideo Card. Sharp focus and remarkable display quality by new design CRT. Cubic and Simple design cabinet with Tilt and Swivel base. LMF and LEF This version of 14MVX Plus is built to meet Swedish requirements for Low Magnetic Field and Low Electrostatics Field. Both features are to reduce the suspected effects of magnetic field and Electrostat ics field to your health down to the MPR 11 recommendation level. TRADEMASX ACXNOW-MENT Syti XGA. WA. d 85141A = r+lf=.d indurmb u M PC PW'T, fIC/AT. ibciul Appieud~ hhdntd of Irdcmwiod Buimaa Mdtims Cmpmaum. are mgistucd wdunuks d the APF4CComputer, be.. If VI&o Cmlisa trwk nmkof @le Canpufu, h=.. 2 14MVX Plus User Manual For U.K. Customers THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. NOTE: ELECTRICAL CONNECTION Your monitor requires an electrical supply of 240 volts ­ 50 Hertz and shfkld be protected by a 5 amp fuse. Your equipment is supplied with a plug incorporating a 5 amp fuse fitted to the mains lead. If the plug that is fitted to the equipment is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted. The cut off plug should be disposed of, do not insert it into a 13 amp socket to prevent the hazard of electric shocks. With pIugs not incorporating a fuse, the circuit must be protected by a 5 amp fuse. WARNING: IMPORTANT THIS EQUIPMENT MUST BE EARTHED. Your equipment is supplied with a mains coloured in accordance with the following Earth, Blue ­ Neutral, Brown - Live. lead, the wires of which are code: Green and Yellow - f Green & Yellow to Earth 1 1 \ Brown to Live Fuse Blue to Neutral Cord Clamp 14MVX Plus User Manual 3 As the colours of the wires in your mains Iead in this equipment may not correspond with the markings identified with the terminals of your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the symbol or coloured Green or Green and Yellow. The wire which which is marked is coloured Brown must be connected with the letter L or coloured Red. to the terminal The wire which is coloured Blue must be connected is marked N or coloured Black. to the terminal which The plug moulded on to the cord incorporates a fuse. For replacement, use a 3 amp BS1 362 fuse. Only ASTA approved fuses should be used. The fuse cover/carrier must be refitted when changing the fuse. In the event of losing the fuse cover/carrier, the plug must not be used until a replacement has been obtained from your nearest electrical stockist and fitted. The colour of the fuse cover/carrier is that of the coloured marks on the insert in the base of the plug. 4 14MVX PZU.S User Manual NEVER @EIi@ REMOVE THE BACK COVER Removal of the back cover MUST be carried out only by quaMed personnel. This display monitor contains high voltages tilde. Ill DO NOT USE IN HOSTILE ENVIRONMENTS DO NOT expose this d~lay monitor to rain or moisture to prevent electric shock or fwe hazard. This unit is designed to be used in the ofiice or home environment. DO NOT subject the unit to vibrations, dust, or corrosive gases. KEEP IN A WELL VENTILATED PLACE DO NOT cover this monitor or place anything against the sides. Ventilation holes are provided on the cabinet to prevent the temperature from risiig. Ventilation holes are also provided on the bottom and the top of the cabinet. AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance. BE CAREFUL OF MAGNETIC FIELDS DO NOT place a magnet, loud speaker system, floppy d~k drive, or anything which will genemte magnetism near the unit. A magnetic field may cause blurred colors or distortion of the displayed pattern. 14MVX PhASUser Manual ~ 5 @PERATmG> Controls Front View Rear View (7) m. (6) (5) (4) (3) (2) (1) J) (8) (1) Power Switch Use this switch to power ON or OFF by pressing it. When the power is ON, green light on the knob turns on to indicate. (2) Contrast Control ((D) Use this to set the foreground brightness cf the screen. (3) Brightness Control (-,, ] Use this to set the background to black. Most of the latest application software utilizes coloured background and this control is usually set at its maximum. (4) Horizontal Size (~] Adjust this control to the preferred horizontal width. If the width is too wide, part of information will be missed from the screen. (5) Horizontal Position (~) Adjust this to place the display at the centre of the screen. 6 14MVX F'hx.sUser Manual (6) Vertical Size [~] Adjust this contxol to the preferred height. (7) Vertical Position [Q 1 Adjust this to place the display at the centre of the screen. (8) Signal Cable Connect the end of the cable to your computer. (9) Power Cord Tn-let Connector Insert proper power cord here. BEFORE CONNECTING TEE MONITOR TO YOUR COMPUTER, MAKE SURE TEE POWER TO TEE MONITOR AND COMPUTER ARE TURNED OFF. 1. Connect the signal cable to your computer's video output comector. `l%ecormector is compatible with IBM PS/2 series computers and VGA standard graphics cards for IBM PC, PC/XT, PC/AT, and compatibles. When you are using the monitor with Apple Macintosh H computer, please obtain an optional converter for comection from your dealer. 2. Connect power cord to the monitor then to wall power outlet. Use the power cord set enclosed with monitor or properly approved power cord, for example, H05 W-F. 3. Power on the monitor then power on your computer. When you switch OFF, reverse the sequence. 4. Adjust front located user controls to obtain right picture size, location, and brightness. Display location on the screen and the size may change when you switch from one application software to another one. 5. Adjust Tilt& Swivel to suit your eye level. DO NOT use the monitor with a bright background light, direct sunshine, or bright light into the screen area. These may increase eye fatigue. Earth magnetic field can affect the display screen, therefore, when the monitor is turned on the bases and shows impurity. of color, power off the monitor then power on to activate automatic degauss circuit. Do not make this sequence too quick. 14MVX Plus User Maimal 7 IP OMPATIBILITY) 14MVX Plus is compatible with: 1. IBM P S/2 series computers with MCGA, VGA, XGA and 85 14/A graphics standards. Signal cable is conilgured as IBM 8514 monitor. 2. Most of the VGA and Super VGA standard graphics boards available for the PC, PC/AT,PS/2 and EISA bus computers. Please ask your dealer for details. 3. Apple Macintosh II computer with Macintosh V]deo Card. You have to obtain a 15 pinto 15 pin converter from your dealer. Comector Pin Assignment Pin 9 10 11 12 13 14 15 No. No Pin Ground Ground No Pin Horizontal Sync Vertical Sync No Connection Pin No, 1 Red Video 2 Green Video 3 Blue Video 4 Ground 5 Ground 6 Red &OUd 7 Green Ground 8 Blue Ground 8 14MVX Plus User Manual @PECIFIcATIO@) CRT 14(1 3V) inches diagonal, 0.28 mm dot pitch, Black B matrix, Silica coated, Short Persistence. Video 0.7 Vpp Sync: Separate H,V or Composite H/V lTL level or Sync on Green at 0.3 Vpp. Horizontal: 30 -- 50 kHz Vertical: 50 --IOOHZ Automatically synchronize. Horizontal: Up to 1024 dots Vertical: Up to 768 lines Input Signal Synchronization Resolution Video Band Width Active Display Area 65 MHz Horizontal: 240 mm Vertical: 180 mm Actual display area depends upon by the graphics board standard. Le& than 0.4 AC 200--240 mm V, 50 Hz Misconvergence Power Supply Power Consumption Dimensions 97 W Approximately 358 (W) x 372 (H) x 403 (D) mm Including Tilt & Swivel base. 15 kg Operation Temperature: 5°C to 35°C Humidity: 30% to 80% Storage -20"C to 60°C 10% to 90% Weight Environmental Conditions 14MVX PIZLS User Manual 9 ...