HITACHI COLOUR MONITOR CMl711ME USER MANUAl BEDIENUNGSANLNTUNG MANUAL DE USUARIO GEBRUIKSAANWISZNG MODE D'EMPLOI / READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER'S MANUAL FOR FUTURE REFERENCES. Forfuture references, record the serial number of your Color monitor. : EPA POLLUTION PREVENTER This monitor is Energy Star compliant when used with a computer equipped with VESA DPMS. The Energy Star emblem does not represent The serial number is located on the rear of the monitor. EPA endorsement of any product or service. SERIAL No. .;s:: BEDIENUNGSANLEITUNG 19 35 50 65 E ; MANUAL DE USUARIO :.' GEBRUIKSAANWIJZING MODE D'EMPLOI 1 i NOTICE 1 The information in this manual is subject to change without notice. Hitachi assumes no responsibility for any errors that may appear in this manual. E TRADEMARK ACKNOWLEDGMENT VGA is a registered trademark of international Business Machines Corporation. Apple and Macintosh II are registered trademarks of Apple Computer, Inc.. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. Energy Star is a trademark of Environmental Protection Agency. 2 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STANDARD SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POWER SAVING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VESA DDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 6 10 11 17 17 18 The following features are provided by the HITACHI Colour Monitor. Sharpest Focus and Highest Contrast Flat screen CRT with anti-glare, dynamic focus circuit, dark glass, and an INVAR shadow gives the sharpest focus and highest contrast to minimize eye fatigue. mask Wide-range Multi-Scanning Automatic scanning and automatic adjustment to conform with a wide range of scanning frequencies and user requirements. Digital Picture Control Function Size, position, trapezoid, rotation and side pincushion are adjustable by digital controls. Geometry setting can be stored for different H/V frequencies. Microprocessor-based preset functions can store 20 sets of geometry settings including the standard factory settings. Digital Colour Control Function Red, green, and blue colour balance is adjustable by digital control. Adjusted colour setting can be stored and recalled by the colour select. Power Saving System The Environmental Protection Agency has established a voluntary program by which manufacturers enable computer products to go into low power states while not being used. This monitor has a low power "sleep" mode, which is compliant with the EPA requirements for the "Energy Star" program, and will assist you in conserving energy. Please refer to the section "POWER SAVING SYSTEM" for details. EasyMenu On Screen display function that enables direct access to adjust operations from front panel. VESA DDC (Display Data Channel) This monitor is VESA DDCl/ZB compliant when used with a computer compliant with VESA DDC. 3 I -mj ' A NEVER REMOVE THE REAR COVER ! The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. A BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power. Le, BE CAREFUL OF GENERATED MAGNETISM ! After the power has been turned on or "DEGAUSS" button has been pressed, the CRT is demagnetized for approximately 10 seconds. This generates a strong magnetic field around the front cover which may affect the data stored on magnetic tape or disks near the front cover. Place such magnetic recording equipment and tapes/disks apart from this unit, m AVOID FREQUENT POWER ON-OFF SWITCHING ! DO NOT repeat OFF and ON in a short period. It may cause blurred colours or distortion of the displayed pattern. fb REMOVE THE POWER CORD FOR COMPLETE SEPARATION ! For complete separation from the power source, remove the power cord from the monitor or from the wall outlet. m AMBIENT ILLUMINATION Avoid direct rays of the sun or room lighting onto the CRT screen in order to prevent eye fatigue. m ABOUT CLEANING This monitor has a non-glare and anti-electrostatic treatment on the surface of the screen. Use water or alcoholic solvent with a soft cloth like gauze to clean the surface of the screen. NEVER use abrasive, glass cleaner containing highly concentrated ammonia and strong base chemicals since they damage the surface treatment. Clean the cabinet and controls with a lightly moistened soft cloth. DO NOT use aerosol sprays, solvents or abrasive cleaners. m CAUTION for 200V operation only This equipment relies on the protective devices in the building installation for short - circuit and over - current protection. Refer to the following table for the suitable number and location of the protectivedevices which should be provided in the building installation. Protective devices in single - phase equipment or sub - assemblies Protection against I Equipment to be connected to POWER SYSTEMS with earthed neutral reliably identified Equipment to be connected to any supply, including IT POWER SYSTEMS and supplies with reversible plugs Earth faults Overcurrent 1 1 2 1 I I Minimum number of fuses or circuit breaker poles Location Both conductors Either of the two conductors 1 B o t h conduc tars I F i-....-.r n f . thetwo t h n -. ..conductor `5 _ I I I I Verify that the protective devices in the building installation meets the conditions in the table prior to installing the equipment. m FCC STATEMENT The following statement applies to this product. Federal Communication Commission (FCC) Statement Warning: NOTE: This equipment has been tested and found to comply with the limit for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. -Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TVtechnician for help. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. h FOR THE CUSTOMERS IN CANADA NOTICE: This digital apparatus does not exceed the class B limits for radio noise emission for a digital apparatus as set out in the radio interference regulations of the Canadian department of communications. m POUR LES UTILISATEURS AU CANADA AVIS: CET APPAREIL NUMERIQUE N'EXCEDE PAS LES LIMITES DE LA CLASSE ,`B" SURLES BRUITS RADIOELECTRIQUES PROVENANT DES APPAREILS NUMERIQUES TEL QUE STIPULE DANS LE RtGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EMIS PAR LE MINISTERE DES COMMUNICATIONS CANADIENNE. ERGONOMICS Under the requirements of german ergonomics standard ZH 11618, draphics or characters. 1. Blue graphics or characters in dark background are not recommended. (This conbination may increase eye fatigue due to poor visibility caused by low contrast.) Graphics controller and monitor are recommended to be used in the following conditions : 2. : Dark characters in bright background. . Display mode s Vertical frequency : 70H.z or higher. 5 ! Install the monitor in the following way, taking care to maintain safety. 1. Installation Install the monitor on a horizontal base. Front Cover - , CRT Surface Y Power Switch ll"PT~llml-I Control Panel ' FRONT VIEW -5 Tilt & Swivel Base Rear Cover / - REAR VIEW 6 m INSTALL THE UNIT IN AN ADEQUATE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment. DO NOT subject the unit to vibrations, dust, or corrosive gases. m KEEP IN A WELL VENTILATED PLACE ! DO NOT cover this monitor or place anything against any sides (not only top, right and left side but also rear and bottom side) of unit. Ventilation holes are provided at all sides of the rear cover to prevent the temperature from rising. A A KEEP AWAY FROM HEATING RADIATION OR SOURCE ! BE CAREFUL OF MAGNETIC FIELDS ! AVOID placing the unit in direct sunshine or near a heating appliance. DO NOT place a magnet, loudspeaker system, floppy disk drive, printer, or anything which will generate magnetism near the unit. A magnetic field may cause blurred colours or distortion of the displayed pattern. 2. Power Cord Connection 0 Make sure the Power Switch is "OFF". Q Make sure to use a power cord meeting the safety standard of the country, in which you are using the monitor. 0 Connect a power cord to the "AC Inlet" of the monitor. @ Connect the plug of the power cord to a receptacle of the correct voltage. A In USA/Canada, use a UL LISTEDKSA LABELLED or CERTIFIED power cord set meeting the following specifications. Type: SVT or SJT Rating: min. 125V, 7A Length: max. 3.1 m Plug type: NEMA 5-15P, Parallel blade, Grounding type, 125V, 15A Failure to do so may cause fire or electric shock hazard. In Europe, a proper European standard approved power cord is to be used with this monitor. For a rated current up to 6 A, a type not lighter than HOSW-F 36 0.75 mm2 or HOSWHZ-F 3G 0.75 mm2 shall be used. The enclosed power cord shall be used if provided. Use only the correct voltage power outlet with safety ground connection. 100 - 120 V for USA, Canada, etc. 200 - 240 V for Europe, etc. (This monitor automatically adjust to the input voltage 100 - 120/ 200 - 240V.) The receptacle should be close to the monitor and easily accessible. A A A 7 I : --! I A FOR THE CUSTOMERS IN U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician. If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply. WARNING: THIS EQUIPMENT MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and Yellow = Earth, Blue = Neutral, Brown = Live. Green &Yellow to Earth Brown to Live Fuse Blue to Neutral Cord Clamp As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol @ or coloured GREEN or GREEN and YELLOW. The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must ...