Tt5CC-l !=I G Colour Monitor CM1721ME User Manual BEDIENUNGSANLEITUNG 17MVX-v2 The serial number is located on the rear of the monitor. READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCES This monitor is Energy Star compliant when used with a computer equipped with VESA DPMS. For future references, record the serial number of your display monitor, SERIAL No. For U.K. Customers THIS PRODUCT IS SUPPLIED WITH A TWO PIN MINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. NOTE: ELECTRICAL CONNECTIION Your monitor requires an electrical supply of 240 volts - 50 Hertz and should be protected by a 5 amp fuse. Your equipment is supplied with a plug incorporating a 5 amp fuse fitted to the mains lead. If the plug that is fitted to the equipment is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted. The cut off plug should be disposed of, do not insert it into a 13 amp socket to prevent the hazard of electric shocks. With plugs not incorporating a fuse, the circuit must be protected by a 5 amp fuse. WARNING: THIS EQUIPMENT MUST BE EARTHED. IMPORTANT Your equipment is supplied with a mains lead, the wires of which are coloured in accordance with the following code: Green and Yellow-Earth, Blue-Neutral, Brown-Live. Green & Yellow to Earth Blue to Neutral Brown to Live Fuse Cord Clamp -I- As the colours of the wires in your mains lead in this equipment may not correspond with the markings identified with the terminals of your plug. proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the symbol or coloured Green or Green and Yellon, The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red. The wire which is coloured Blue must be connected to the terminal which is marked N or colourcd Black The plug moulded on to the cord incorporates a fuse. For replacement, use a 5 amp BS 1362 fuse. Only ASTA approved fuses should be used. The fuse cover/carrier must be refitted when changing the fuse. In the event of losing the fuse cover/carrier, the plug must not be used until a replacement has been obtained from your nearest electrical stockist and fitted. The colour of the fuse cover/carrier is that of the coloured marks on the insert in the base of the plug. - II - Please read the following instructions carefully to prevent potential hazards. This manual should be retained for future use. 1. Do not expose the monitor to rain, water, moisture, or direct sunlight. 2. Do not spill liquid into the monitor 3. Do not insert any objects into the monitor cabinet's openings. 4. Do not place near or above sources of heat such as heaters or radiators. 5. Do not block or cover ventilation opening with any material. The openings and slots on the cabinet provide necessary air flow for heat dissipation. The unit should never be enclosed or built upon unless adequate ventilation is provided. 6. Do not remove the cover to try to service this unit. Servicing of any nature should only be performed by authorized service personnel. 7. WARNING! Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. 8. The On/Off switch is not a disconnecting device. Make sure to remove the AC power cord after using. 9. When the monitor is turned on continuously for a long period, the phosphors of the CRT face plate may "bum" leaving a permanent image on the screen. In order to preserve CRT life, be sure to turn off the monitor or decrease the displayed intensity when not in use. - III - 10. WARNING! The voltage ratings and the rated frequencies are posted on the back panel of this product. Please see the overlay in the center of the back panel of this product. NEVER connect to any other voltage or frequency. Follow ALL warnings and instructions marked on the product. 11. This, product is equipped with a 3-wire grounding-type plug. It will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, the outlet can be replaced by an electrician. Do not defeat the safety purpose of the grounding-type plug by improper use or alteration. 12. Power source . This monitor is able to operate using power sources from 108-264VAC/60-50Hz by means of internal auto power switching. . For 120V operation, use only with power cord having a parallel blade grounding-type plug, rated at I OA- 125V. . For 240V operation, use only with power cord having a tandem blade grounding-type plug rated 1 OA-250V minimum. - IV - Bitte lesen Sie diese Sicherheitshinweise sorgftitig durch, damit die richtige Verwendung des Gerstes sichergestellt wird. Diese Anleitung sorg<ig aufbewahren. 1. Das Bildschirmger~t nicht Regen, Wasser, Feuchtigkeit oder direktem Sonnenlicht aussetzen. 2. Keine Fltissigkeiten tiber dem Bildschirmgerat Verschtitten. 3. Niemals Gegenstande durch die &fnungen in das Innere des Gerates stecken oder hineinfallen lassen. 4. Das BildschirmgeCit nicht in der Nahe von Heizgeraten der Heizungen aufstellen. 5. Nicht die beliiftungsdffhungen des Gehauses blockieren oder abdecken. Diese @frrungen und Schlitze im Gehause sorgen tir die notwendige Ventilation. Das Bildschirmgerat sollte niemals mit einer Verkleidung umgeben oder in einem Regal eingebaut werden. falls keine ausreichende Beltiftung vorhanden ist 6. Niemals versuchen, das Gehause zu entfemen oder das Bildschirmgerat selber zu war-ten. Alle Wartungsarbeiten sollten nur vom Kundendienst durchgefiihrt werden. 7. Nicht versuchen, das Bildschirmgerat selbst zu war-ten. Im Inneren des Gerates sind gef&rliche elektrische Spannungen und andere Gefahren vorhanden. 8. Der Netzschalter ist keine Trennvorrichtung Sicherstellen, daR die NetzanschluRleitung, wenn das Gerat Iangere Zeit nicht benutzt wird, aus der netzsteckdose gezongen wird. -V- 9. Bei Einstellung des Bildschinngerates auf starkste Helligkeit und Kontrast uber langere Zeit Konnen die Leuchtschicht der Zur Verlangerung der Bildrohrenoberfhiche einbrennen. Lebensdauer der Bildrohre ist sicherzustellen, dal3 das Bildschirmgerat nach der Verwendung ausgeschaltet wird oder Helligkeit und Kontrast verringert werden. 10. Die Angaben zur Spannung und Frequenz entnehmen Sie dem Schliessen Sie Ihr Gerat nie an eine Fabrikschild. Stromquelle mit andeier. als der dort genannten Spannung/ Frequenz an. Beachten Sie ausserdem alle am Gerat angebrachten Warn- und Bedienungshinweise. 11. Ihr Gerat ist mit einem dreipoligen Schukostecker ausgestattet. Dieser Stecker kann nur an eine Schutzkontaktsteckdose Sollte der Stecker nicht in die angeschlossen wrerden. Steckdose passen, lassen Sie diese bitte von einem Elektriker auswechseln. Es mu8 sichergestellt Bildwiederholfrequenz von werden. dal3 d i e minimale 70 Hz bei Positivdarstellung und 60 Hz bei Negativdarstellung nicht unterschritten wird (storendes Bildschirmflimmem konnte die Folge sein). Weiterhin wird aus ergonomischen Griinden empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhohte Augenbelastung bei zu geringem Zeichenkontrast w&ren die Folge). "Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betragt 70dB(A) oder weniger" - VI - (Gerat, Typ, Bezeichnung) in ijbereinstimmung mit den Bestimmungen der BMPT-AmtsblVfg 243/l 99 1 funk-entstort ist. Der vorschriftsmai3ige Betrieb mancher Gerate (zB Me&sender) kann allerdings gewissen Ems&r ankungen unterliegen. Beachten Sie deshalb die Hinweise in der Bedienungsanleitung. Dem Bundesamt' fur Zulassungen in der Telekommunikation wurde das inverkehrbringen dieses Gerates angezeigt und die Berechtigung zur ijberprtifung der Serie auf die Einhaltung der Bestimmungen eingeraumt. - VII - / NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause h a r m f u l interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect l/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. - VIII - INDEX 1. I N T R O D U C T I O N . . _. . . _. . . . . . . . . . . . . . . . .._.. . . . . . . . . . . . . .:.. 2. CHECK LIST .._............... . _.......___...... . . . . . . . ..____............... 2 3 3. CONTROLS AND ADJUSTMENTS ................................ 4 3.1 LOCATION AND FUNCTION OF CONTROLS.. ....... 4 3.2 REWRITE COMPANY'S NAME ON SCREEN 1 ...... 7 3.3 FUNCTIONS ADJUSTMENTS ON SCREEN 2.. ........ 7 4. P O W E R M A N A G E M E N T S Y S T E M . . . . . . 10 5. PLUG & PLAY.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6. INSTALLATION.. _. . 12 7. USE OF TILT-SWIVEL.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 8. S P E C I F I C A T I O N ___......____. . ..____ _. _. ._____.__... 14 9. FACTORY PRESET DISPLAY MODES t... . . . . . . . . . . . . 15 10. TROUBLE SHOOTING.. _. . . . . . . . . . _. . . . . . . 15 -I- 1. INTRODUCTION This colour monitor is an excellent choice for high resolution It automatically scans compatibility, versatility and quality. horizontal frequencies between 30 and 64 kHz and vertical frequencies between 47 and 104 Hz and is equipped with an Easy Menu microprocessor controlled multi-frequency function. This monitor offers compatibility with virtually every major high resolution video board for PC and video standards including VGA, SVGA. XGA, VESA and is even compatible with APPLE MAC II by using an inexpensive optional connector. The 1280 X 1024 maximum resolution will help you get the most flexibility with today's or tomorrow's PC video standards. Whether your video adapter has a multi-frequency or fixedfrequency analog colour signal, it will interface with this colour monitor. The unit is also equipped with an energy-saving function. It is compatible with the EPA Energy Star & VESA DPMS powersaving standards. . VGA, SVGA, XGA, APPLE MAC II: EPA, and VESA are trademarks of their respective owners. -2- 2. CHECK LIST Before installation, please check the contents of the shipping carton. The carton should contain the following items: - Power cord - User manual - Colour monitor If any of the above items are missing, contact your supplier as soon as possible. -3- 3. CONTROLS AND ADJUSTMENTS 3.1 LOCATION AND FUNCTION OF CONTROLS 1. POWER AND POWER SAVING INDICATOR When the power to the monitor is ON, the indicator is lit. In normal operation, the indicator is green. While in power saving mode, the indicator will turn to orange. 2. POWER SWITCH Used to turn the power of the monitor ON and OFF 3. STATUS SELECT SWITCH (Easy Menu) Selects from screen 1 or screen 2 images and blanked windows for display. Press button. The screen 1 image, as in figure A, will be shown on the screen. The company's name, the polarity and frequencies of the horizontal and vertical sync signals, and the resolution of the mode which is currently in use now will be displayed. Front View 10,SNATS 161/5/ -4- il 1s I Company's Name Frequency & Polarity of Horizontal Sync Signal Frequency & Polarity of Vertical Sync Signal Mode Resolution in Use Figure A Press button again and the screen 2 image as in figure B will appear on the screen. The tinction symbols (including Horizontal size and phase, Vertical size and center, Pincushion, Trapezoid, Contrast, Brightness, R. G. B. color, Image Rotation, Manual Degauss, Window, & Recall), the function description (simply select to adjust). both step number and parameter bars ...