HITACHI COLOR MONITOR CM2096ME USER MANUAL For future references, record the serial number of your display monitor. SERIAL No. The serial number is located on the rear of the monitor. EPA POLLUTION PREVENTER READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER'S MANUAL FOR FUTURE REFERENCES. USER MANUAL 2 MANUAL DE USUARIO GEBRUiKSAANWiJZlNG MODE D'EMPLOI 51 66 I LI Energy Star is a trademark of Environmental Protection Agency. The Energy Star emblem does not represent EPA endorsement of any product or service. m m - The information in this manual is subject to change without notice. Hitachi assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGMENT VGA is a registered trademark of international Business Machines Corporation. APPLE is a registered trademark of Apple Computer, Inc.. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. NEVER REMOVE THE BACK COVER ! The back cover MUST be removed only by authorized service personnel. This display monitor contains high voltage components. BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power. BE CAREFUL OF GENERATED MAGNETISM ! After the power has been turned on or "DEGAUSS" button has been pressed, the CRT is demagnetized for approximately 10 seconds. This generates a strong magnetic field around the bezel which may affect the data stored on magnetic tape or disks near the bezel. Place such magnetic recording equipment and tapes/disks apart from this unit. AVOID FREQUENT POWER ON-OFF SWITCHING ! DO NOT repeat OFF and ON in a short period. It may cause blurred colors or distortion of the displayed pattern. REMOVE THE POWER CORD FOR COMPLETE SEPARATION ! For complete separation from the power source, remove the power cord from the monitor or from the wall outlet. AMBIENT ILLUMINATION ! Avoid direct rays of the sun or room lighting onto the CRT surface in order to prevent eye fatigue. ABOUT CLEANING This monitor has a non-glare and anti-electrostatic treatment on the CRT surface. Use water or alcoholicsolvent with soft cloth like gauze to clean the CRTsurface. NEVER use abrasive, glass cleaner containing highly concentrated ammonia and strong base chemicals since they damage the CRT surface treatment. Clean the cabinet and controls with a lightly moistened soft cloth. DO NOT use aerosol sprays, solvents or abrasive cleaners. 2 CAUTION for 200V operation only in U.S.A. This equipment relies on the protective devices in the building installation for short circuit and over - current protection. Refer to the following table for the suitable number and location of the protective devices which should be provided in the building installation. Protective devices in single - phase equipment or sub - assemblies Minimum number Protection against of fuses or circuit - breaker poles Equiment to be connected to POWER SYSTEMS with earthed neutral reliably identified Equiment to be connected to any supply, including IT POWER SYSTEMS and supplies with reversible plugs Earth faults Overcurrent 1 1 Both conductors Either of the two conductors Location I L _ Earth faults 2 Both conductors Overcurrent 1 Either of the two conductors Verify that the protective devices in the building installation meets the conditions in the table prior to installing the equipment. 3 - - FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STANDARDSETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 9 10 18 The following features are provided by the Hitachi Color Monitor CM2096M. Sharpest Focus and Highest Contrast CRT with anti-glare, dynamic focus circuit, and dark glass, gives the sharpest focus and highest contrast to minimize eye fatigue. Wide-range Multi-Scanning Automatic scanning and automatic adjustment to conform with a wide range of scanning frequencies and user requirements. Digital Picture Control Function Size, position, trapezoid, rotation and side pincushion are adjustable by digital controls. Geometry setting can be stored for different H/V frequencies. Microprocessor-based preset functions can store 31 sets of geometry settings including the standard factory settings. Digital Color Control Function Red, green and blue color balance is adjustable by digital control. Adjusted color setting can be stored and recalled by the color select button. Power Saving System The Environmental Protection Agency (EPA,U.S.A.) .has established a voluntary program by which manufacturers enable computer products to go into low power states while not being used. This monitor has a low power "sleep"mode, which is compliant with the EPA requirements for the "Energy Star" program, and will assist you in conserving energy. Please refer to the section of "Power Saving System" for details. install the monitor in the following way, taking care to maintain safety. Front Cover L , , CRT Surface I Power Switch Control Panel A FRONT VIEW `Tilt & Swivel Base LED ,......-.....~..,.........-.....~......-........................................... : Store ' ' ' ' ' Button Geometry Adjust Contrast I Button Increase /B;;;;ase ; rjht; ess l;20s.psina Power Switch !-!A Buttons Color Adjust Buttons k$$, (with Color Button) Rear Panel AC Inlet' D-Sub Mini -Connector Terminal REAR VIEW 5 1. Installation ) Install the monitor on a horizontal base. INSTALL THE UNIT IN ADEQUATE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment. DO NOTsubject the unit to vibrations, dust, or corrosive gases. KEEP IN A WELL-VENTILATED PLACE ! DO NOT cover this monitor or place anything against any sides (not only top, right and left side but also rear and bottom side) of unit. Ventilation holes are provided at all sides of the back cover to prevent the temperature from rising. KEEP AWAY FROM HEATING RADIATION OR SOURCE ! AVOID placing the unit in direct sunshine or near a heating appliance. BE CAREFUL OF MAGNETIC FIELDS ! DO NOT place a magnet, loudspeaker system, floppy disk drive, printer, or anything which will generate magnetism near the unit. A magnetic field may cause blurred colors or distortion of the displayed pattern. 2. Power Cord Connection ) Make sure the Power Switch is "OFF". ) Connect a power cord to the "AC Inlet" of the monitor. ) Connect the plug of the power cord to a receptacle of the correct voltage. q In USA/Canada, use a UL LISTEDKSA LABELLED or CERTIFIED power cord set meeting the following specifications. Type: SVT or SJT Length: max. 3.1 m Rating: min. 125V, 7A Plug type: NEMA 5-l 5P, Parallel blade, Grounding type, 125V, 15A Failure to do so may cause fire or electric shock hazard. In Europe, a proper European standard approved power cord is to be used with this monitor. For a rated current up to 6 A, a type not lighter than H05VV-F 3G 0.75 mm2 or H05VVH2-F 3G 0.75 mm2 shall be used. Cl The accessory power cord shall be used if provided. 6 q 17 Use only the correct voltage power outlet with safety ground connection. 110 - 120 V for USA, Canada, etc. 200 - 240 V for Europe. etc. (This monitor automatically selects the input voltage 110 - 1201200 - 240V.) The receptacle should be close to the monitor and easily accessible. I E ii FOR THE CUSTOMERS IN U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PINMAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. NOTE: ELECTRICAL CONNECTION Your monitor requires an electrical supply of 240 volts - 50 hertz and should be protected by a 5 amp fuse. Your equipment is supplied with a plug incorporating a 5 amp fuse fitted to the mains lead. If the plug that is fitted to the equipment is not suitable for your socket outlet, it must be cut off and an appropriate plug must be fitted. The cut off plug should be disposed of, do not insert it into a 13 amp socket to prevent the hazard of electric shocks. With plugs not incorporating a fuse, the circuit must be protected by 5 amp fuse. WARNING: THIS EQUIPMENT MUST BE EARTHED IMPORTANT: Your equipment is supplied with a mains lead, the wires of which are colored in accordance with the following code: Green and Yellow - Earth, Blue - Neutral, Brown - Live. Green & Yellow to Earth Brown to Live Fuse Blue to Neutral Cord Clamp As the colors of the wires in your mains lead in this equipment may not correspond with the markings identified with the terminals of your plug, proceed as follows: The wires which are colored Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or bythe earth symbol @or colored Green or Green and Yellow. The wire which is colored Brown must be connected to the terminal which is marked with the letter L or colored Red. The wire which is colored Blue must be connected to the terminal which is marked N or colored Black. The plug moulded onto the cord incorporates a fuse. For replacement, use a 5 amp BS1362 fuse. Only ASTA approved fuses should be used. The fuse cover/carrier must be refitted when changing the fuse. In the event of losing the fuse cover/carrier, the plug must not be used until a replacement has been obtained from your nearest electrical stockist and fitted. the color of the fuse cover/carrier is that of the colored marks on the insert in the base of the plug. 7 - 3. Signal Cable Connection - D-Sub Mini 1 S-pin Connector Terminal 5 10 15 1 6 11 Shell (connected to Frame Ground) TABLE 1 ) Use an optional signal cable for a VGA-type graphics board. ) Connect the connector to the "D-Sub Mini 15-pin Connector Terminal", and secure the screws on the connector shell firmly. 8 4. Power On ) Turn the Power Switch of the monitor (refer to "OPERATION - Power Switch") on first, then the computer. NOTICE: If the picture doesn't appear, turn OFF the power switch, make sure of the following, wait at least 30 seconds, and turn it back ON. Make sure the power switch of the computer, power cord connection, signal cable connection, and the input sync. signal are right. 1 - Microprocessor-based preset functions can store 31 sets of geometry settings including the standard settings. 7 sets are preset at factory, 24sets are available to users. The following industrial standard settings have been preprogrammed by the factory. No. Video Mode Name (with Resolution and Vertical Frequency) Clock Frequency 25.18 MHz Horizontal Frequency 31.47 kHz 1 VGA-3 640 X 480 - 60Hz 2 VESA 640 X 480 - 72Hz 31.50 MHz 3 7 . 8 6 kHz 4 8 . 0 8 kHz 56.48 kHz 60.02 kHz 6 1 APPLE 1152 X 870 - 75Hz 1 100.00 MHz 7 CAD 1280 X 1024 - 74Hz 135.00 MHz Note: 1. 2. 68.68 kHz 78.86 kHz Input signals with approximately the same frequencies may be regarded as the same signal. The following horizontal timing conditions are recommended. Horizontal front porch should be more than 0.1 ps. Horizontal sync. width should be more than l.Ous. Horizontal back porch should be more than 1.2~~. Horizontal blanking width should be more than 3.5~~. The following vertical timing conditions are recommended. Vertical blanking width should be more than 45Ops. Vertical back porch should be more than 400~s. 3. 9 ~m - See the "Control Panel" at front of the monitor. You can adjust the picture position, size, side pincushion, trapezoid, rotation, color balance, brightness and contrast of the monitor with these buttons. q If two or more buttons are pressed at the same time, they will be invalid except when mentioned in the following. 1. FUNCTION OF CONTROLS ( Power Switch [ a] 1 l Power is switched ON or OFF by pushing this button. When the power is ON, ) The power LED will lights. ) The picture position, size, side pincushion, trapezoid, color balance, brightness, rotation, and contrast of the monitor will be adjusted automatically. (refer to "Automatic Settings") ) The contrast adjustment mode will be set, and the contrast LED will light. q If all LEDs light continuously or the power LED blinks, make sure the power switch of the computer, signal cable connection, and the input sync. signal are right. The monitor will recover rapidly when the monitor receives a right sync. signal. Degauss Button , STORE 0 [ DEGAUSS ] , I l The manual degaussing function is activated by pressing this button. ) Use the degauss button only when you see color impurities on the screen after turning the monitor ON. Remembe ...