Hitachi Plasma Display Tabletop Stand Model CMPAD06 Installation Instructions Thank you for purchasing the Hitachi Plasma Display Table top Stand. To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual in a safe place for future reference. This plasma display tabletop stand is for use only with the following model: CMP5000WX Request an installation specialist to install this unit. This company assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling. Parts Configuration Chart IConfirming the parts provided Before assembly, check to make sure that none of the parts provided are missing. · Base cover x 1 · Stand pipes (left and right, interchangable) x 2 · Hexagonal wrench x 1 · Screws (4 x 8) x 4 · Installation bolts 1 (M8 x 20) x 2 · Installation bolts 2 (M8 x 40) x 2 · Stabilization bolts x 2 Usage cautions to ensure correct usage Symbols The following symbols are used to ensure safe usage of the product, to prevent danger to yourself and other parties and to prevent damage to property. WARNING CAUTION This symbol indicates that incorrect handling due to ignoring this symbol can result in the possibility of personal injury or even death. This symbol indicates that incorrect handling due to ignoring this symbol can result in the possibility of personal injury and physical damage. This symbol indicates additional cautions (including warnings). This symbol indicates forbidden actions. This symbol indicates required actions. Caution (general) Forbidden (general) Required (general) WARNING Always use at least two people to perform the installation work. Injury could result from dropping heavy objects. Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the plasma display falls. CAUTION Do not mount the plasma display in an instable place. The display could fall or break, resulting in physical injury. Avoid installing in locations where the temperature and humidity are excessively high, and where contact with water is possible. These can result in fire or electrical shock. Do not block the ventilation holes. Also provide sufficient clearance in regard to avoid blocking the ventilation. The internal temperature could elevate and possibly result in fire. Do not alter any of the parts. And do not use broken parts. This could result in injury due to the plasma display falling. Stand assembling Screws (4 x 8) 1. Turn the base cover over so the underside is facing up. 2. Insert the stand pipes into the base cover. 3. Use the included screws to stabilize the stand pipes. Stand pipe Screws (4 x 8) Stand pipe Base cover Stand attaching to the Plasma Display Normal Installation Step 1. With the plasma display lying flat, insert and secure the two Installation bolts 1 (M8 x 20) in the holes "a" located in the plasma display housing. At this point, tighten these bolts 1 only until the threads are no longer visible when viewed from t he side (you will be unable to attach the display if the bolts are screwed in completely). Installation bolt 1 (M8 x 20) Holes "a" (holes in center of plasma display) Installation bolt 1 Plasma display housing Stop screwing down the bolt when the threads are no longer visible. Plasma display Regarding the stand pipe screw holes when the stand is used as a desktop stand C B A C´ B´ A´ C B A C´ B´ A´ Specifications Normal use With optional speakers attached to both sides of display Screw holes used with stand orientation B, B' Stand attaching to the Plasma Display Step 2. As shown in figure, hook the stand pipe holes onto the screw heads of the installation bolts 1, then slide the stand upwards to the main plasma display until it engages the installation bolts 1 (once put together with the display, the stand will slides no more than 19 mm (3/4 inch)). Step 3. Pass the installation bolts 2 (M8 x 40) through the stand pipes and tighten the installation bolts securely with the included hexagonal wrench. Step 4. Tighten the installation bolts 1 securely with the hexagonal wrench provided. Installation bolts 2 (M8 x 40) (Step 3) Notes · Place a sheet or protective cover to protect the display from scratches or damage. · Assemble only with the plasma display lying flat on a table or similar surface. · Insert the bolts vertically in the holes and tighten them, but do not apply excessive pressure that tightens them more than necessary. · Move the stand so that the stand screw holes and the nuts that connect the main display line up correctly. · The display is a 50" model that weighs approximately 40 kilograms (88 lb) and has little depth, making the display very unstable. For this reason, at least two people are required for setup and installation. Slide the stand (Step 2) Table top stand Sheet Instructions for using the main display packing material as a stand for the working on the display Main plasma display packaging setup Outer box Inner box frame Pad Mirror mat Pad Plasma display Step 1. Construct the stand for the plasma display using the inner box frame and pads shown in the figure above (all pads are identical). Pad Inner box frame Step 2. Set the plasma display down on the pads as shown in the figure below. Plasma display Mirror mat Inner box frame topped by two pads Step 3. Follow the instructions in Steps 1-4 in "Normal Installation" to attach the stand to the plasma display. After assembling, connect the stand to the floor to prevent from falling over. Stabilizing to the floor · Use screws (sold separately) to attach and stabilize the stand. Sample use of the stabilization bolts 1. Attach the stabilization bolts that come with the plasma display. 2. Stabilize the display by connecting to a wall or standing beam with a strong cord. (Repeat the same steps in the laterally direction to stabilize the assembly to the left and right.) Use cord and hooks that are available on the market (sold separately). Installation coordinates for screws used to stabilize the stand to the floor 248(9-3/4) 485(19-3/32) 64(2+17/32) 11.5(7/16) 275(10-13/16) Specificatio Dimensions 566 (W) x 508 (H) x 339 (D) mm (22-5/16 (W) x 20 (H) x 13-3/8 (D) in.) 4.0 kg (8.82 lb) 42.9 kg (94.58 lb) (When the 50 inch plasma display is attached) Weight Main material/ Steel sheet Surface treatment ABS Dimensions Diagram Normal use (without optional speakers) Optional speakers attached to both sides of display 1368 Speaker 1218 Speaker 150 774 566 220 508 339 Hitachi, Ltd. Tokyo Japan Digital Media Division 292 Yohida-cho, Totsuka-ku, Yokohama, 244-0817 Japan (045) 866-6302 ...