CPS220W USER'S MANUAL Please read this user's manual thoroughly to ensure correct usage through understanding. BEDIENUNGSANLEITUNG Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung aufmerksam. MANUEL D'UTILISATION Nous vous recommandons de lire attentivement ce menuel pour bien assimiler le fonctionnement de l'appareil. MANUAL D'ISTRUZIONI Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter comprendere quanto riportato ai fini di un corretto utilizzo del proiettore. MANUAL DE USUARIO Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto. GEBRUIKSAANWIJZNG Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de uitgebreide mogelijkheden. BRUKERHÅNDBOK Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk. INSTRUÇÕES DO PROPRIETÁRIO Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do usuário. PORTGÊS NORSK NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Liquid Crystal Projector Liquid Crystal Projector ENGLISH CP-S220W USER'S MANUAL Thank you for purchasing this HITACHI liquid crystal projector. Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE: * The information in this manual is subject to change without notice. * The manufacturer assumes no responsibility for any errors that may appear in this manual * The reproduction, transmission or use of this documents or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT: * PS/2, VGA and XGA are registered trademark of International Business Machines Corporation. * Apple, Macintosh, Mac and ADB are registered trademarks of Apple Computer, Inc. * VESA and SVGA are trademarks of the Video Electronics Standard Association. * Windows is registered trademarks of Microsoft Corporation. * Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned. CONTENTS FEATURES ....................................P.2 BEFORE USE ................................P.2 Contents of Package...........................P.2 Part Names .........................................P.3 Loading the Battery .............................P.4 TROUBLESHOOTING.................P.19 OSD Message...................................P.19 Indicators Message ...........................P.20 Symptom ...........................................P.21 SPECIFICATIONS .......................P.22 WARRANTY AND AFTER-SERVICE...P.23 REGULATORY NOTICES ...........P.24 Tables: Table 1. Installation Reference .............P.5 Table 2. Basic Operations.....................P.9 Table 3. Setup Menu...........................P.11 Table 4. Input Menu ............................P.12 Table 5. Image Menu ..........................P.13 Table 6. Options Menu........................P.14 Table 7. No Signal Menu.....................P.15 Table 8. OSD Message.......................P.19 Table 9. Indicator Message.................P.20 Table 10. Symptom .............................P.21 Table 11. Specifications ......................P.22 INSTALLATION .............................P.5 Installation of the projector and Screen.....P.5 Angle Adjustment ................................P.5 Cabling ................................................P.6 Power Connection...............................P.6 Example of System Setup...................P.7 Plug & Play..........................................P.7 OPERATIONS................................P.8 Switching the Power Supply ON/OFF ....P.8 Basic Operation...................................P.9 Setup Menu.......................................P.11 Input Menu ........................................P.12 Image Menu ......................................P.13 Options Menu....................................P.14 No Signal Menu.................................P.15 MAINTENANCE...........................P.16 Lamp .................................................P.16 Air Filter Maintenance .......................P.18 Other Maintenance............................P.18 ENGLISH-1 FEATURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. · Outstanding brightness The UHB lamp and high-efficiency optical system assure a high level of brightness. · Partial magnification function Interesting parts of images can be magnified for closer viewing. · Distortion correction function Distortion-free images are quickly available. BEFORE USE Contents of package Make sure all of the following items are included in the package. If anything is missing, please contact your dealer. NOTE: Keep the original packing material for future reshipment. Power Cord US Type Projector Power Cord UK Type Power Cord Europe Type RGB Cable User's Manual (this manual) STANDBY/ON Video Cable Audio Cable (Stereo Mini) VIDEO RGB MENU SELECT MENU POSITION RESET Mac Adapter Safety Instructions MAGNIFY FREEZE VOLUME MUTE OFF AUTO TIMER BLANK Remote Controller containing Battery Carrying Bag ENGLISH-2 B E F O R E U S E ( c o n t i nu e d ) ENGLISH Part Names Zoom Knob Focus Ring Remote Control Sensor Power Switch AC Inlet (to the Power Cord) Ventilation Openings (Intake) Lens Slide Lens door Foot Adjuster FRONT/LEFT VIEW OF THE PROJECTOR Control Panel (Refer to P.8 "OPERATIONS") RESET Button MUTE Button INPUT Button STANDBY/ON Button Foot Adjuster Button Air Filter and Intake (for the Cooling Fan) Speaker Rear Foot Adjuster REAR/RIGHT VIEW OF THE PROJECTOR Terminal Panel (Refer below) S-VIDEO Terminal RGB IN Terminal CONTROL Terminal VIDEO Terminal TERMINAL PANEL AUDIO IN Terminal Remote Control Sensor Ventilation Openings (exhaust) LAMP Indicator TEMP Indicator POWER Indicator MENU Button ENGLISH-3 BEFORE USE (continued) Part Names (continued) VIDEO Button STANDBY/ON Button Button Button Button Button MENU Button MAGNIFY MAGNIFY MAGNIFY OFF MENU SELECT STANDBY/ON VIDEO RGB RGB Button MENU SELECT Button POSITION Button RESET Button VOLUME VOLUME Button Button MENU POSITION RESET Button Button Button MUTE OFF AUTO TIMER BLANK MAGNIFY FREEZE VOLUME FREEZE Button MUTE Button BLANK Button AUTO Button TIMER Button Battery Holder (Refer to P.8 "OPERATIONS") REMOTE CONTROLLER Loading the Battery CAUTION Danger of explosion if battery is incorrectly replaced. Be careful in handling the battery according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. Replace only with the same or equivalent type recommended by the manufacturer. Use the 3V micro lithium battery type no. CR2025 only. When you dispose the battery, you must obey the law in the relative area or country. Keep the battery away from children and pets. First Loading: In original packing, the battery is installed in the battery holder of the remote controller with protection film(the transparent filmsome of which is inside the battery folder). Pull out the protection film to load the battery. "+" side Replacing: 1. See the reverse side of the remote controller. 2. Pinch the groove and pull out battery holder as the drawing right. 3. Remove the worn battery. 4. Install the new battery with "+" side facing. 5. Push in and click the battery holder. Pull out Battery Holder ENGLISH-4 INSTALLATION Install the projector in a suitable environment according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. Refer to the drawing and table below for determining of the screen size and projection distance. a: Distance from the LCD projector to the screen. The projection distance shown in the table below are for full size (800 x 600 dots). b: Distance from the lens center to the bottom of the screen (a, b: +/-10%) Table 1. Installation Reference TOP VIEW Screen size (inches) 40 60 80 100 120 150 a (inches) Min. 37 57 77 96 116 145 194 Max. 46 69 93 116 139 174 233 b (inches) 3 5 7 9 10 13 17 b a 200 SIDE VIEW Installation of liquid crystal projector Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage. Be especially careful not to install it with ventilation holes blocked. Angle Adjustment Use the foot adjuster on the bottom of the projector to adjust the projection angle. It is variable within 0° to 10° approximately. Foot Adjuster Press the foot adjuster button 1. Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle. 2. Release the button to lock at the angle to be fixed. 3. Turn the rear foot adjuster to adjust the left-right slope. Rear Foot Adjuster Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or the fingers could get caught and cause personal injury. ENGLISH-5 ENGLISH Installation of the Projector and Screen INSTALLATION (continued) Cabling * Incorrect connecting could result in fire or electrical shock. Please read this manual and the separate "SAFETY INSTRUCTIONS". * Before connecting, turn off to all devices to be connected. *Before connecting, read the instruction manuals of the devices to be connected, and make sure that the projector is compatible with the device. *The cables (Power cord, RGB cable and other cables) may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified. Core RGB Signal Input: Connect the RGB IN terminal of the projector to the display signal output of the computer by the enclosed RGB cable. Secure the screws on the connector and tighten. For some modes, the enclosed Mac adapter is necessary. Refer to P.22 "SPECIFICATION" and "Table 1. Example of Compatible Computer Signal" of the TECNICAL section. NOTE: Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Video Signal Input: Connect the VIDEO terminal of the projector to the video signal output of the video tape recorder by the enclosed video cable except for S-Video signal. For S-Video signal, use the S-VIDEO terminal of the projector and the optional cable for S-Video. Audio Signal Input: Connect the AUDIO IN terminal of the projector to the audio signal output by the enclosed audio cable. RS-232C: Connect the CONTROL terminal of the projector to the computer by the optional RS-232C cable. Refer to the manual of the RS-232C cable for the control command. Power Connection WARINING Be carful in handling the power cord according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. Connect the power cord firmly. Avoid using a loose, unsound outlet or contact failure. Power outlet Power Cord AC Inlet Use the correct one of the enclosed power cords depending on the power outlet to be use. Connect the AC inlet of the projector to the power outlet firmly by the power cord. ENGLISH-6 INSTALLATION (continued) ENGLISH AC Inlet Video tape recorder with S jack Video tape recorder Example of system setup Computer (notebook type) RGB Cable RS-232C Cable Computer (desktop type) Connecting with notebook computer When connecting with notebook computer, set to valid the RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information. Plug & Play This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible. (Plug & play is a system configured with peripheral equipment including a computer and display, and an operating system. NOTE: Use the RGB cable included with this projector when using plug & play. With other cables, pins (12) (14) (15) are sometimes not connected. ENGLISH-7 OPERATIONS Please read this manual, and the separate "SAFETY INSTRUCTIONS" thoroughly before using the equipment. Always ensure that the equipment is used safely. Switching the Power Supply ON/OFF Switching Power ON 1. Check that the power cord is connected correctly. 2. Set the power switch to [ | ]. The standby mode is selected, and the Power indicator is turned to orange. 3. Press the STANDBY/ON button on the control panel or the remote. Warm-up begins and the Power indicator blinks in green. 4. The Power indicator ceases blinking and turns to green when power is ON. Open the lens door. 5. Adjust picture size using the projection lens Zoom Knob. 6. Adjust focus using the ...