Liquid Crystal Projector ENGLISH USER'S MANUAL Thank you for purchasing this liquid crystal projector. Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE: · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this documents or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT: · PS/2, VGA and XGA are registered trademark of International Business Machines Corporation. · Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. · VESA and SVGA are trademarks of the Video Electronics Standard Association. · Windows is registered trademarks of Microsoft Corporation. · Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned. CONTENTS FEATURES ....................................P.2 BEFORE USE ................................P.2 Contents of Package...........................P.2 Part Names .........................................P.3 Loading the Battery .............................P.4 Fixing the Handle ................................P.5 MAINTENANCE...........................P.17 Lamp .................................................P.17 Air Filter Maintenance .......................P.19 Other Maintenance............................P.19 TROUBLESHOOTING.................P.20 OSD Message...................................P.20 Indicators Message ...........................P.21 Symptom ...........................................P.22 INSTALLATION .............................P.6 Installation of the projector and Screen.....P.6 Angle Adjustment ................................P.6 Cabling ................................................P.7 Power Connection...............................P.8 Example of System Setup...................P.8 Plug & Play..........................................P.8 SPECIFICATIONS .......................P.23 WARRANTY AND AFTER-SERVICE...P.24 Tables: Table 1. Installation Reference .............P.6 Table 2. Basic Operations...................P.10 Table 3. Setup Menu...........................P.12 Table 4. Input Menu ............................P.13 Table 5. Image Menu ..........................P.14 Table 6. Options Menu........................P.15 Table 7. No Signal Menu.....................P.16 Table 8. OSD Message.......................P.20 Table 9. Indicator Message.................P.21 Table 10. Symptom .............................P.22 Table 11. Specifications ......................P.23 OPERATIONS................................P.9 Switching the Power Supply ON/OFF ....P.9 Basic Operation.................................P.10 Setup Menu.......................................P.12 Input Menu ........................................P.13 Image Menu ......................................P.14 Options Menu....................................P.15 No Signal Menu.................................P.16 ENGLISH-1 FEATURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. · Outstanding brightness The UHB lamp and high-efficiency optical system assure a high level of brightness. · Partial magnification function Interesting parts of images can be magnified for closer viewing. · Distortion correction function Distortion-free images are quickly available. BEFORE USE Contents of package Make sure all of the following items are included in the package. If anything is missing, please contact your dealer. NOTE: Keep the original packing material for future reshipment. Power Cord US Type Projector 0000000000000 USER'S MANUAL Please read this user's manual thoroughly to ensure correct usage through understanding. Power Cord UK Type Power Cord Europe Type BEDIENUNGSANLEITUNG Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung aufmerksam. MANUEL D'UTILISATION Nous vous recommandons de lire attentivement ce menuel pour bien assimiler le fonctionnement de l'appareil. MANUAL D'ISTRUZIONI Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter comprendere quanto riportato ai fini di un corretto utilizzo del proiettore. MANUAL DE USUARIO Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto. GEBRUIKSAANWIJZNG Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de uitgebreide mogelijkheden. BRUKERHÅNDBOK Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk. INSTRUÇÕES DO PROPRIETÁRIO Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do usuário. NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Liquid Crystal Projector TECHNICAL REGULATORY NOTICES User's Manual (this manual) Handle S-Video cable (S-Video mini DIN4-pin) TECHNICAL PORTGÊS RGB Cable Video/Audio Cable Mouse cable (PS/2) STANDBY/ON LASER VIDEO NORSK BLANK RGB AUTO MENU POSITION MENU SELECT RESET FREEZE MAGNIFY OFF MUTE VOLUME Safety Instructions Stereo Mini-jack cable TIMER Batteries for Remote Control Transmitter Remote Control Transmitter ENGLISH-2 B E F O R E U S E ( c o n t i nu e d ) Speaker Zoom Knob Focus Ring Handle Hook Power Switch AC Inlet (to the Power Cord) Ventilation Openings (Intake) Lens Slide Lens door Foot Adjuster FRONT/LEFT VIEW OF THE PROJECTOR Remote Control Sensor Control Panel (Refer to P.9 "OPERATIONS") STANDBY/ON Button MUTE Button INPUT Button LAMP Indicator TEMP Indicator POWER Indicator RESET Button MENU Button Foot Adjuster Button Air Filter and Intake (for the Cooling Fan) Rear Foot Adjuster REAR/RIGHT VIEW OF THE PROJECTOR Ventilation Openings (exhaust) Terminal Panel (Refer below) Remote Control Sensor RGB IN 1 Terminal RGB IN 2 Terminal S-VIDEO Terminal VIDEO IN Terminal AUDIO IN L Terminal 1 RGB IN 2 AUDIO IN R Terminal AUDIO IN 1 Terminal AUDIO IN 2 Terminal AUDIO OUT Terminal AUDIO IN VIDEO IN S-VIDEO IN AUDIO 1 IN 2 AUDIO OUT USB RGB OUT CONTROL CONTROL Terminal RGB OUT Terminal USB Terminal TERMINAL PANEL ENGLISH-3 ENGLISH Part Names BEFORE USE (continued) Part Names (continued) VIDEO button STANDBY/ON button BLANK button DISK PAD Used to operate the mouse shift function and left click function. STAN DBY/O N LAS ER RG K BLAN B V O IDE LASER button RGB button MOUSE / RIGHT button Used to click the right mouse button. POSITION button O AUT NU ME ME NU SEL POS ITION AUTO button MENU button MENU SELECT button Used to click the left mouse button. RESET button Used to click the right mouse button. ECT ET RES FREEZE button FRE EZE VOL NIFY MAG OFF UME TE MU T R IME VOLUME button MUTE button TIMER button , , , button Used to operate the mouse shift function. MAGNIFY button REMOTE CONTROL TRANSMITTER (Refer to P.9 "OPERATIONS") : These functions works when the mouse control function is activated. Remember, the POSITION, BLANK ON and MENU ON functions disable the mouse control function. WARNING The laser pointer of the remote control transmitter is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems. CAUTION LASER RADIATIONDO NOT STARE INTO BEAM WAVE LENGTH: 650nm MAX . OUTPUT: 1mW CLASS 2 LASER PRODUCT RADIAZIONI LASER NON GUARDARE NEL RAGGIO LUCE APPARECCHIO LASER DI CLASSE 2 RAYONNEMENT LASER MANUFACTURED NE PAS REGARDER DANS LE FAISCEAU APPAREIL A LASER DE CLASSE 2 LASER-STRAHLUNG PLACE OF MANUFACTURER:A NICHT IN DEN STRAHL MADE IN JAPAN BLICKEN LASER KLASSE2 IEC60825-1:1993+A1:1997 NOTE: To prevent any malfunction; · Do not give the remote control transmitter any physical impact. Take care not to drop. · Do not place the heavy objects on the remote control transmitter. · Do not wet the remote control transmitter or place it on any wet object. · Do not place the remote control transmitter close to the cooling fan of the projector. · Do not disassemble the remote control transmitter in case of malfunction. Please bring it to the service station. ENGLISH-4 B E F O R E U S E ( c o n t i nu e d ) Install the AA batteries into the remote control transmitter. 1. Remove the battery cover. Push the knob while lifting up the battery cover. 2. Loading the batteries. Make sure the plus and minus poles are correctly oriented. 3. Close the battery cover. 1 2 CAUTION · Use only the specified batteries with this remote control transmitter. Also, do not mix new and old batteries. This could cause in battery cracking or leakage, which could result in fire or personal injury. · When loading the batteries, make sure the plus and minus terminals are correctly oriented as indicated in the remote control transmitter. Incorrect orientation could cause battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment. · When you dispose the battery, you obey the law in the relative area or country. · Keep the battery away from children and pets. · When not to be used for an extended period, remove the batteries from the remote control transmitter. NOTE: Replace the batteries when remote control transmitter operation becomes difficult. Fixing the Handle Fixing the enclosed handle if you need. 1. Raise up the handle hook, and pass one end of the handle through the hole of handle hook. 2. Buckle the end of the handle, as the right drawing. 3. Fix the other end of the handle to the other handle hook in the same way. 1 2 CAUTION Make sure the handle is fixed before carrying the projector with the handle. If the projector should be dropped from the handle should be off, it could result in an injury, and continued use could result in fire or electrical shock. Do not flourish the projector with the handle. ENGLISH-5 ENGLISH Loading the Battery INSTALLATION Installation of the Projector and Screen Refer to the drawing and table below for determining of the screen size and projection distance. a: Distance from the LCD projector to the screen. The projection distance shown in the table below are for full size (1024 x 768 dots). Table 1. Installation Reference TOP VIEW Screen size (inches) 40 60 80 100 120 150 200 a (inches) Min. 65 98 131 163 196 246 328 Max. 78 117 157 196 236 295 394 a SIDE VIEW CAUTION · Install the projector in a suitable environment according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. · Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage. Be especially careful not to install it with ventilation holes blocked. Angle Adjustment Use the foot adjuster on the bottom of the projector to adjust the projection angle. It is variable within 0° to 9° approximately. Foot Adjuster Press the foot adjuster button Rear Foot Adjuster 1. Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle. 2. Release the button to lock at the angle to be fixed. 3. Turn the rear foot adjuster to adjust the left-right slope. CAUTION Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or the fingers could get caught and cause personal injury. ENGLISH-6 INSTALLATION (continued) RGB signal input: Connect the RGB IN 1 or 2 terminal of the projector to the RGB signal output of the computer by the enclosed RGB cable. For some modes, the optional Mac adapter is necessary. Consult your dealer to connect with the Apple computer. Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Audio signal input (from computer) : Connect the AUDIO IN 1 or 2 terminal of the projector to the audio signal output of the computer by the optional audio cable. Video signal input: Connect the VIDEO IN terminal of the projector to the video signal output of the video tape recorder by the enclosed video/audio cable except for S-Video signal. For S-Video signal, use the S-VIDEO IN terminal of the projector and the optional S-Video cable with Mini DIN 4-pin jack. Audio signal input (from video tape recorder) : Connect the AUDIO IN R and L terminals of the projector to the audio output of the video tape recorder by the enclosed video/audio cable with RCA jack. RGB signal output: Connect the RGB OUT terminal of the projector to the RGB signal input terminal of t ...