Hitachi Plasma TV Horizontal Wall-mount Unit Model PWT001 Installation Instructions Thank you for purchasing the Hitachi Plasma TV Wall-mount Unit. To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual in a safe place for future reference. This plasma TV wall-mount unit is for use with the following models: HITACHI Plasma TV CL32-PD2100, CL37-PD2100, CL42-PD2100, 32PD5100, 42PD5100, 42PMA500 32PD5000, 32PD5200, 32PD5300, 37PD5200, 42PD5000, 42PD5200, 42PD5300, CMP4211/2, CMP4213/4 Special techniques are necessary for installation of the plasma TV. I Do not attempt to perform this work by yourself. I Request an installation specialist to install this unit. I This company assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling. I Please remember that if you remove the plasma TV set from the wall later, you will find the screw holes and anchor bolts for the mounting unit left on the wall. Also note that a long use of the plasma TV set may discolor the wall around it due to its heat and air flow. To dealers and shops G To ensure customer safety, be sure to design the installation location so that the strength is sufficient to withstand the weight of both the plasma TV and the wall-mount unit. G Always use at least two persons for all installations. G Fully tighten all of the mounting screws as specified in the installation instructions. Parts Configuration Chart In the parts packing Wall-mount metal (top) x 1 M6 x 18 screw x 10 M5 - 6 flat washer x8 TV-mount metal x2 Wall-mount metal (center) x 1 Wire clamp x2 Parts for CL37-PD2100 only Wall-mount metal (bottom) x 1 Bracket (R),(L) x 1 each M6 x 18 screw x4 Usage cautions to ensure correct usage Symbols GThe following symbols are used to ensure safe usage of the product, to prevent danger to yourself and other parties and to prevent damage to property. WARNING CAUTION I This symbol indicates that incorrect handling due to ignoring this symbol can result in the possibility of personal injury or even death. I This symbol indicates that incorrect handling due to ignoring this symbol can result in the possibility of personal injury and physical damage. IThis symbol indicates additional cautions (including warnings). Caution (general) IThis symbol indicates forbidden actions. Forbidden (general) IThis symbol indicates required actions. Required (general) Indicates that the power plug is to be disconnected from the power outlet. Disassembly prohibited Safety Cautions WARNING I When a malfunction occurs, disconnect the power plug from the power outlet and take measures to prevent other people coming near the plasma TV. In the cases such as G The plasma TV is loose and vibrates to an extreme degree, G Mounting screws or parts are loose or missing, failure to take appropriate actions can result in injury. Perform the following actions immediately whenever a malfunction occurs. xTurn off the plasma TV power switch. Disconnect the power plug from the power outlet. Surround the area with rope, etc., to prevent other people coming near. Contact your local dealer. Disconnect the power plug from the power outlet. Contact your local dealer. I Ask your dealer to install, move or adjust the angle of the wall-mount unit. Incorrect installation or adjustment can cause the plasma TV to fall. Handling by other than professional contractors is prohibited. ­2­ Installation Location WARNING Plaster board or thin ply wood, etc. I The wall where the wall-mount unit is to be installed must be capable of long-term support of the total load of the plasma TV and wall-mount unit. Measures should also be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. Incorrect installation can cause the plasma TV to fall and cause injury. Total load of the (plasma TV + wall-mount unit) = 26kg···CL32-PD2100 34kg···CL37-PD2100 37kg···CL42-PD2100 G Installation on a wooden wall Pillar or thick ply wood. Always install so that the load is supported by a pillar. If the strength of the pillar is insufficient, add reinforcement. Do not install on decorative posts or plaster board. G Installation on a concrete wall Use commercially available anchors that are capable of fully supporting the load of the plasma TV. CAUTION I Avoid installing in locations where the temperature and humidity are excessively high, and where contact with water is possible. These can result in fire or electrical shock. 10cm or more I Do not block the ventilation holes. Also provide sufficient clearance in regard to the surroundings to avoid blocking the ventilation. 10cm 10cm or more or more The internal temperature could elevate and possibly result in fire. I Do not install close to an airconditioner intake or outlet. Do not install in locations where there is excessive amounts of dust, oily smoke or tobacco smoke. Fire could result. I Install only on a vertical surface. Avoid sloped surface. Also, do not install facing upward. The internal temperature could elevate and possibly result in fire. Injury or damage could also result from falling. ­3­ CAUTION I Do not install in locations where there is excessive vibration or impact. Injury and damage could result from falling. I Do not install where there is direct sunlight and other strong light. Strong light could result in eye fatigue during usage. Installing WARNING I Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the plasma TV falls. I Make sure the TVmount metals and wall-mount metals are firmly engaged. Failure to do so could cause the plasma TV to fall. I Do not alter any of the parts. And do not use broken parts. This could result in injury due to the plasma TV falling. I Always use at least two people to perform the installation work. Injury could result from dropping heavy objects. I Use care to prevent the fingers being caught. Installation Method Assembling the wall-mount metals I Assemble the wall-mount metal (Top), (Center) and (Bottom) with 4 M6 x 18 screws. M6 x 18 screw x 4 cutout Wall-mount metal (top) Wall-mount metal (center) Wall-mount metal (bottom) ­4­ Mounting the wall-mount unit on the wall 1. Prepare at least four sets of commercially available anchors and screws, etc., for various types of walls. 2. Carefully read the safety cautions concerning installation locations as described in this instruction manual and then select a suitable location for installation. 3. The relationship between the plasma TV exterior and center, and the positions of the wall-mount unit mounting holes is shown in the diagram for the various models. Install the anchors in the wall as shown in the diagram and process the holes as necessary. G Make sure that the strengths of the wall and the screws are fully sufficient. 32 inch 37 inch ­5­ 42 inch 4. Fasten the wall-mount unit securely to the wall. G Clamp to two or more of the long slotted holes in the upper and lower parts of each wall-mounting metal in a well-balanced manner. cutout 5. Dressing the cables G When passing the plasma TV power cord and signal cables behind the plasma TV, use wire clamps, etc., to prevent cable damage. Mount on a firm, solid surface. Wall-mount metal (top) Wall-mount metal (bottom) Use the washers provided as necessary. Wire clamps Mounting the TV-mount metals on the plasma TV 1. Remove the stand. x Place a protective sheet cover on the top of a table and place the plasma TV on the cover with the back side upward. Remove the 4 EMI ground screws. (for CL32-PD2100 only.) Remove the 4 or 5 (CL37-PD2100) screws fastening the stand and remove the stand in the direction indicated by the arrow mark. Remove the 4 screws Remove the 4 EMI ground screws.(CL32-PD2100) 2. Installing the TV-mount metals CL32-PD2100 IFasten the two TV-mount metals to the back of the plasma TV with 4 M6 x 18 screws. 4 M6 x 18 screws TV-mount metal Plasma TV The 3rd TV-mount metal hole Remove the screws (CL37-PD2100) Table Stand Protective sheet cover The 4th TV-mount metal hole ­6­ CL37-PD2100 x Fasten the bracket (R) , (L) to the TV mount metal with 4 M6 x 18 screws. TV-mount metal 4 M6 x 18 screws Fasten the two TV-mount metals to the back of the plasma TV with 4 M6 x 18 screws. 4 M6 x 18 screws Bracket (R),(L) Bracket The 1st TV-mount metal hole CL42-PD2100 IFasten the two TV-mount metals to the back of the plasma TV with 4 M6 x 18 screws. The 2nd TV-mount metal hole The 5th TV-mount metal hole Installing the plasma TV on the wall mount x Hang the TV-mount metal catches on the wall-mount unit cutouts. Fasten with 2 M6 x 18 screws from the bottom. After make sure all mouting works are completely done, connect power cord and signal cables. Cutout Make sure that the top cutouts and catchs are engaged. Wall-mount unit GThe plasma TV should always be carried by at least two people. GDisconnect the plasma TV power cord and all cables. Catch 2 M6 x 18 screws TV-mount metal ­7­ Product Specifications External Dimensions Dimension (A),(B) Model CL32-PD2100 CL37-PD2100 CL42-PD2100 A 377 414 414 B 113 100 51 Mass Main material 2.6kg Steel sheet Surface treatment Black electrodeposited baked paint Angle adjustment Vertical fix Products mounted Hitachi Plasma TV CL32-PD2100 , CL37-PD2100 , CL42-PD2100 Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 ­12 Nishi Shinbashi, 2 ­ Chome, Minato ­ Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer -service@hitachi-eu.com HITACHI EUROPE S.A. 364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.com HITACHI EUROPE GmbH Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München GERMANY Tel: +49-89-991 80-0 Fax: +49- 89-991 80-224 Hotline: +49-180-551 25 51 (12ct/min) Email: HSE- DUS.service@hitachi-eu.com HITACHI EUROPE S.A. Gran Via Carlos III, 86, planta 5 Edificios Trade - Torre Este 08028 Barcelona SPAIN Tel: 93 409 2550 Fax: 93 491 3513 Email: atencion.cliente@hitachi-eu.com HITACHI EUROPE srl Via Tommaso Gulli N.39, 20147 Milano, Italia ITALY Tel: +39 02 487861 Tel: +39 02 38073415 Servizio Clienti Fax: +39 02 48786381/2 Email: customerservice.italy@hitachi-eu.com HITACHI Europe AB Box 77 S-164 94 Kista SWEDEN Tel: +46 (0) 8 562 711 00 Fax: +46 (0) 8 562 711 13 Email: csgswe@hitachi-eu.com HITACHI EUROPE S.A.S Lyon Office B.P. 45, 69671 BRON CEDEX FRANCE Tel: 04 72 14 29 70 Fax: 04 72 14 29 99 Email: france.consommateur@hitachi-eu.com HITACH EUROPE AB Egebækgård Egebækvej 98 DK-2850 Nærum DENMARK Tel: +45 43 43 6050 Fax: +45 43 60 51 Email: csgnor@hitachi-eu.com HITACHI EUROPE LTD (Norway) AB STRANDVEIEN 18 1366 Lysaker NORWAY Tel: 67 5190 30 Fax: 67 5190 32 Email: csgnor@hitachi-eu.com HITACHI EUROPE AB Neopoli / Niemenkatu 73 FIN-15140 Lahti FINLAND Tel : +358 3 8858 271 Fax: +358 3 8858 272 Email: csgnor@hitachi-eu.com Hitachi Europe Ltd Bergensesteenweg 421 1600 Sint- Pieters-Leeuw BELGIUM Tel: +32 2 363 99 01 Fax: +32 2 363 99 00 Email: sofie.van.bom@hitachi-eu.com HITACHI EUROPE LTD Na Sychrove 975/8 101 27 Pr aha 10 ­ Bohdalec CZECH REPUBLIC Tel: +420 267 212 383 Fax: +420 267 212 385 Email: csgnor@hitachi-eu.com www.hitachidigitalmedia.com ...