User manual HITACHI VTFX980EUKN

VIDEO CASSETTE RECORDER VT-FX980E(UKN) Instruction manual is a registered trademark of SRT, Inc. A Jerry lggulden invention licensed in association with Arthur D. Little Enterprises, Inc. FOR FURTHER INFORMATION PLEASE CONTACT OUR CUSTOMER HELP LINE ON 01628-643029 To obtain the best performance please read this instruction manual completely. PAL QR32061 SUBSIDIARY INFORMATION ADDITIONAL OPERATIONS BASIC OPERATIONS VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufactured under licence from Gemstar Development Corporation. SETTING UP Auto Install System -- simply plug in all leads and press the OPERATE button. Dear Hitachi Customer Congratulations on your choice of a Hitachi Video Cassette Recorder (VCR). And welcome to our company-wide commitment to your complete satisfaction and viewing enjoyment. INFORMATION FOR YOUR SAFETY Please read the following instructions carefully before using this VCR. The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS1362 fuse must be used of the same rating. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. If there is no alternative to cut off the mains plug, ensure that you dispose it immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Blue = Neutral, Brown = Live As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. On no account connect either of these wires to the terminal marked E or by the earth symbol or coloured green or green and yellow. WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Mains supply: AC 230V, 50 Hz only AC 230V, 50Hz DECODER/CANAL PLUS AUDIO OUT/ SORTIE SON EURO. A/V R/D. L/G. RF OUT SORTIE RF AERIAL ANTENNE · The OPERATE button located on the front of the VCR switches the VCR on and off, leaving the clock facility unaffected. · The OPERATE button is labelled " / I" this button allows you to select operate on or electrical power standby. · The OPERATE button is secondarily connected and does not separate the apparatus from the mains supply in the switched-off position. Safety · Do not remove panel covers by unscrewing. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. · Should any solid object or liquid fall into the cabinet, remove the mains lead and have it checked by qualified personnel before operating it any further. · To disconnect the mains lead, pull out the plug itself. Never pull the lead. · If the unit is to be left unattended for a long period and it is not intended to use the timer recording function, it is recommended to switch off the VCR and removed the plug. If you intend to record during your absence, remember there is no necessity for the TV receiver to be switched on. Cautions: When the VCR is moved from a cold to a warm place, dew condensation can occur on the cylinder. To avoid damaging the cylinder or tape do not operate the set immediately. Allow it to dry by leaving it powered on for 2 ~ 3 hours. 2 CONTENTS CAUTION: AUTO INSTALL SYSTEM -- Please ensure that all leads are connected as illustrated as in page 6 and 7, otherwise auto installation will not work. This instruction manual consists of the following four sections. Section-1 This section tells you how to set up your new VCR and how to use the VCR controls. Setting Up Connections............................................................................... 6 Customer Controls ................................................................... 8 Remote Operation .................................................................. 10 Auto Installation Function ..................................................... 11 Pre-tuning of Built-in TV Tuner ............................................ 13 Auto Clock Setting Using PDC Signal ................................. 19 Setting the Clock Manually ....................................................20 Cassette Tapes ........................................................................ 21 Section-2 This section tells you how to playback a tape and record a TV programme. Basic Operations Playback ................................................................................... 23 Playback Using Jog/Shuttle Ring ......................................... 26 Recording TV Programmes................................................... 27 Tape Analyzer...........................................................................30 Instant Recording Timer (IRT)............................................... 31 Timer Recording ..................................................................... 32 VIDEO LINK -- Recording Using Satellite Decoder or TV .40 Section-3 This section tells you how to use the additional functions. Additional Operations Tape Navigation ..................................................................... 42 Navi Lock ..................................................................................49 Soap Recording........................................................................51 MOVIETEXTTM ........................................................................ 53 .......................................................... 54 Special Characteristics · Linear Time Counter...................................................... 55 · Automatic Rewind ......................................................... 55 · Rewind Shut Off............................................................. 55 · Mode Lock Function ...................................................... 55 · Tape Remaining Display Function............................... 56 · Index Function................................................................ 57 · Rental Play ...................................................................... 57 Menu Features ........................................................................ 58 VIDEO Plus+® System Setup ................................................ 62 Editing · VIDEO Dubbing................................................................63 · AUDIO Dubbing...............................................................65 · Tape Dubbing ................................................................. 67 · Synchro Editing.............................................................. 69 "Satellite/Cable box" Decoder Operation ........................... 71 Satellite Receiver Operation.................................................. 73 Hi-Fi Sound.............................................................................. 78 How to Operate Your TV by Using the Remote Control Handset ............................................ 79 Section-4 Subsidiary Information Problem Guide........................................................................ 82 User Guide Display..................................................................83 Maintenance............................................................................ 84 Specifications .......................................................................... 85 PDC (Programme Delivery Control) function...................... 86 Battery Safety Guidelines...................................................... 87 Warranty Letter ....................................................................... 89 Some Do's and Don'ts........................................................... 91 3 FEATURES · The VIDEO Plus+® programming system allows you to programme the VCR for timer recording by simply entering a PlusCode® programming number. · MOVIETEXTTM * MOVIETEXT is a registered trademarks of Hitachi Home Electronics (Europe) Ltd. · Satellite receiver controller. · Tape Navigation allows you to automatically locate a programme you want to view, and also to list on the TV screen the recorded contents of every tape you have recorded on this VCR. · ­ a feature which allows the VCR to automatically or manually skip past detected commercial groups during replay of a recorded television broadcast. · "Satellite/Cable box" decoder socket provided. · The built-in digital stereo sound decoder permits the reception of NICAM (Near Instantaneous Compand Audio Multiplex) broadcast. · 12-programme/1-year preset recording. · Dynamic picture equalizer. · Shuttle function on remote control and VCR -- shuttle control for fast search and variable speed playback. · Auto Install System (Plug and Play) -- tunes in stations, selects correct order, sets clock and date. · Auto Tuning -- tunes in stations, sorts correct order, and sets clock. · High quality slow motion/still frame pictures. · Stereo Sound -- record and playback. · Phono audio outputs. · NTSC playback. · Graphic OSD. · Setting the clock using a PDC signal (Auto clock set). · Automatic controls for easier operation. -- Auto Programme Play immediately starts to play a recorded programme by simply turning on the VCR after timer recording has finished. -- Auto Head Cleaning system minimizes the need for accessory cleaners and professional head cleaning. · · · · · · · · · · · -- Auto Tracking system automatically adjusts the tracking so the picture is optimized. -- Rental Play immediately starts to play a tape without its safety tab, rewinds the tape after play is ended and eject it, then turns off the VCR. -- Auto Play immediately starts to play a tape without its safety tab. -- Auto Eject & Auto Tape Canceller ejects a cassette without its tab when the REC or REC/IRT button is pressed. -- Auto Operate On turns on the VCR by simply inserting a cassette. -- Auto Rewind/Rewind Shut-off automatically rewinds a tape at its end and automatically shuts off at its beginning if the VCR is switched off into standby mode, while rewinding. Fine slow motion. Easy preset tuning provides up to 49 programmes. Instant Recording Timer (IRT) allows you to quickly set-up the VCR to record a TV programme for a specified period. The supplied remote control handset can operate not only two VCRs but also 15 different types of TVs. Index function -- convenient for locating the desired programme on your tape. PDC (Programme Delivery Control) function -- corrects the start and stop times of a timer recording if the TV station delays programme. Video and audio dubbing allows you to simply and easily insert new video and audio sequence into existing tape. VIDEO LINK allows you to easily prepare the VCR to record signals from a satellite/cable decoder. Soap Recording function is an easy way to set timer programming by choosing a registered programme from Tape Navi data menu. Navi Lock function prevent accidently deleting of important programmes. Tape Analyzer (ATRS) automatically detect the type of tape used during recording. Accessories supplied Check and identify the accessories supplied. If any are missing or appear damaged, consult your dealer. 2 pcs. Aerial Cable for connecting this VCR and a TV 4 Remote Control Handset Batteries for remote control handset (R6) Section-1 Connection Setting Up SETTING UP Pages 6 -- 7 This tells you how to connect your VCR to an aerial, TV, etc. Customer Controls Pages 8 -- 9 This tells you the location and the detailed functions of the switches, buttons, VCR display and connection terminals on the VCR. Remote Operation Page 10 This tells you how to insert batteries into the remote control handset and how to operate your VCR remotely. Auto Installation Function This tells you how to automatically tune in all broadcast channels and set the clock and date. Page 11 Pre-tuning of Built-in TV Tuner Pages 13 -- 18 This VCR incorporates a complete TV tuner (just like your normal TV) and can be pre-tuned to receive up to 49 TV programmes. To preset satellite programmes, see page 73. Auto Clock Setting using PDC signal and Setting the Clock Manually Pages 19 -- 20 The clock display area in the VCR display panel will look like "­ ­:­­" until you set the 24-hour clock. The clock must be set to the correct time before you can programme the VCR for timer recording and instant recording timer. This section explains the two clock setting methods. A. Setting the VCR clock automatically using a PDC signal. B. Setting the remote control clock, then transferring the set time to the VCR to set the VCR clock. Cassette Tapes Page 21 This tells you how to insert and remove a cassette, and how to protect recordings from accidental erasure. 5 CONNECTION Basic Method Aerial AERIAL DECODER/CANAL PLUS AUDIO OUT/ SORTIE SON EURO. A/V R/D. L/G. RF OUT SORTIE RF AERIAL ANTENNE To AC outlet AC 230V/50Hz RF OUT TV set Do not connect to the mains supply socket before connecting all leads, refer to page 11. Aerial cable (supplied) Aerial socket For even better sound and picture quality we recommend to use scart connection. Please refer page 7 for scart connection. PRECAUTIONS On Installation · Do not install the unit near heat sources such as radiators or air ducts or in a place subject to direct sunlight, excessive dust, mechanical vibrations or shocks. · Never bring a magnet or magnetized object near the VCR because it will adversely affect the performance of the VCR. · Ensure the VCR is installed on a flat surface. The unit is designed for operation in a horizontal position. 6 Aerial Satellite/Cable box decoder AERIAL Do not connect to the mains supply socket before connecting all leads, refer to page 11. To AC outlet AC 230V/50Hz DECODER/CANAL PLUS AUDIO OUT/ SORTIE SON EURO. A/V R/D. L/G. RF OUT SORTIE RF AERIAL ANTENNE RF OUT TV set Scart socket Aerial socket Aerial cable (supplied) Scart connector lead available from your dealer (not supplied) Set your TV to its proper AV line (scart lead) to receive signal via the scart connector lead. This connection will improve the picture and sound quality. Make sure the indicator lights in the VCR display to feed the audio and video signals from the VCR to TV. If not, press the VCR/TV button on the handset to display it. This connection also allows you to record the TV programme selected on the TV. To do this, press the AUX button on the remote control handset to display the "L1" indicator in the VCR's display instead of a VCR programme number. Operation · Moisture condensation Moisture condensation on the cylinder, one of the most crucial parts of the VCR, will cause damage to the tape. The VCR should not be operated for at least 2 hours after being moved from a cold to a hot environment to avoid condensation from occurring on the cylinder. Cleaning · DO NOT use volatile agents such as benzine, alcohol, thinner, or chemically processed cloth to wipe the surface of the VCR case. These agents may cause the surface finish to deteriorate or peel off. Repacking · It is wise for you to save the packing materials and box in case you ever need to ship or store your unit. 7 SETTING UP Connecting your VCR to your television using scart lead. CUSTOMER CONTROLS VCR Customer Controls 123 4 5678 Item No. 1 Function OPERATE ( / I) (Standby/operate) button EJECT (0) button VIDEO LINK button Cassette compartment STOP (7) button PLAY/STILL (6) button Infrared transmitter Jog dial Shuttle ring Tape navigation programme select up/down (5/) buttons TAPE NAVIGATION button REC/IRT button PROG (5/) (programme up/down) button Remote control receiving window CA ( ) indicator - lights when CA function is in use. Reset switch VIDEO LINK indicator ­­ lights when VIDEO LINK function is in use AUDIO IN (L-mono),(R) sockets VIDEO IN socket Decoder socket AUDIO OUT (L), (R) sockets for stereo system connection AERIAL -- signal input RF OUT -- signal out to TV Scart socket VCR Display "­" appears Time, during reverse Time counter or direction VCR mode indicator viewing PLAY -- playback SRCH -- visual search SLOW -- slow play REW -- rewind FF -- fast forward STILL -- play pause and frame advance VCR, operate mode Audio indicators REC -- record (flashes during record pause) Tape-in indicator TV programme number or Auxiliary (L1/L2/L3) Timer indicator Page 2 21 40 21 24 23 73 26 26 45 42 27 12 10 54 82 40 67 67 71 ­ 6 6 7 20 55 23 23 24 23 24 24 23 23 25 27 21 27 63 32 REV FWD VIDEO LINK COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION VIDEO LINK CA 17 1615 14 13 12 11 10 9 To open the cover: Pull the cover forward. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VIDEO LINK COMMERCIAL ADVANCE VIDEO LINK CA REV FWD VIDEO LINK COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION 16 17 18 19 20 21 VIDEO LINK VIDEO IN L (MONO)-AUDIO IN-R CA 19 18 20 21 22 22 23 24 AERIAL ANTENNE DECODER/CANAL PLUS AUDIO OUT/ SORTIE SON EURO. A/V R/D. L/G. RF OUT SORTIE RF 25 24 23 25 26 27 28 26 27 28 29 30 31 30 29 31 REW FWD VIDEO LINK COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION VIDEO LINK CA 8 1 Item No. 1 2 22 3 4 5 6 7 8 9 Function Transmission window OPERATE -- switch between operate and standby mode VCR/TV select button MENU -- to recall OSD menu NAVI button Cursor buttons ENTER button REC -- record button Tape transport button -- playback -- rewind or search -- fast forward or search -- stops play/record function Pause/still button Shuttle knob Frame advance during still INDEX button -- INDEX feature button MOVIE TEXT button TV mute button Buttons used TV PROG button exclusively to TV Operate button operate the TV TV volume button Note: Four buttons 16 ­ 19 are used only when operating the TV. PROG (programme up/down) button AUX button -- select L1, L2 or L3 input Display clock/timer programme information VIDEO Plus+ programming button Number buttons PROG -- to enter timer programme information SP/LP -- changes tape speed during record VCR1/2/TV select button PDC button DISP -- to recall on-screen display CLOCK/COUNT -- changes VCR display CH1/2 button A. DUB button V. DUB button 0000 -- clears time counter MENU -- to recall OSD menu CORRECT button CLOCK -- enter or correct time on handset EXTEND (­ or +) AUX -- to select L1 or L2 input CL buttons -- mode lock TRANS button -- transmits data ENTER button -- to enter PlusCode programming number Page 10 32 23 58 44 13 13 27 24 OPERATE VCR/TV AUX 2 PROG 21 20 TV PROG 3 19 18 17 16 15 14 ENTER REC INDEX 4 5 6 7 8 9 NAVI MENU MOVIE TEXT CA 13 10 11 12 13 14 15 16 17 18 19 23 26 23 57 54 53 80 80 80 80 10 REV FWD 12 20 21 11 22 23 24 25 26 42 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 13 67 20 33 20 36 21 10 86 56 55 25 66 64 55 58 20 20 33 36 55 34 33 23 1 2 VIDEO PLUS ENTER TRANS 4 41 1 4 DLY/WKL 2 5 8 0 3 6 CL 24 25 26 27 28 29 30 31 32 3 40 39 38 37 36 35 34 7 PROG SP/LP 9 AUX EXTEND PDC VCR1/2/TV CLOCK CORRECT MENU CLOCK COUNT DISP 0000 A. DUB CH1/2 V. DUB 33 9 SETTING UP Remote Control Handset Customer Controls REMOTE OPERATION Power source of infrared remote control handset The infrared remote control handset is powered by two batteries (size IEC standard R6). The life of the batteries is about six months although this depends on the number of times the handset is used. Replace the batteries when operation is not possible or when the operating distance becomes too small. Note: When replacing the batteries, remove the used batteries and press the OPERATE button and hold it pressed for 10 seconds, then insert the new batteries and replace the battery cover. Remote operations To operate this VCR with the remote control handset, press the VCR1/2/TV select button on the handset to display "VCR 1" or "VCR 2", then point it at the receiver on the front of the VCR. · The REC, play , rewind , fast forward , stop , pause and frame advance buttons can control your VCR even if "TV" is displayed when the "REMOTE " display (see page 60 for details) is set to (1) or (­) · This VCR is designed so it can be controlled when either "VCR 1" or "VCR 2" is selected (see page 60). Note: Be sure to press the mark ( , , , ) of the tape transport button on the remote control to operate the VCR, not the centre of the buttons. Pressing the centre of the button could cause a malfunction. REV FWD VIDEO LINK COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION VIDEO LINK CA Display 1 2 VIDEO PLUS ENTER TRANS 4 1 4 DLY/WKL 2 5 8 0 3 6 CL 7 PROG 3 9 AUX EXTEND SP/LP PDC VCR1/2/TV CLOCK CORRECT MENU CLOCK COUNT DISP 0000 VCR1/2/TV select button CH1/2 A. DUB V. DUB VCR 1/2/TV Select button The supplied remote control handset is designed to operate up to two types of Hitachi VCRs and 15 different types of TV. · Refer to page 79 when using the handset to operate the TV. · For dubbing your own tapes, as an example, the recording VCR and playback VCR can be controlled by a single handset. In order to operate two VCRs, set this VCR remote code to "VCR 2", and the other VCR to "VCR 1", following the "REMOTE (1), (2) or (­)" section on page 60. 1 2 VIDEO PLUS ENTER TRANS 4 1 4 DLY/WKL 2 5 8 0 3 6 CL 7 PROG 3 9 AUX EXTEND SP/LP PDC VCR1/2/TV CLOCK CORRECT MENU CLOCK COUNT DISP 0000 VCR1/2/TV select button A. DUB CH1/2 V. DUB REV FWD 10 AUTO INSTALLATION FUNCTION Auto Install (Plug & Play) function This automatically tunes all broadcast channels, sets the clock and date. Controls VCR/TV screen Switch on the mains supply socket after completely connecting all leads (as described on pages 6 and 7). The VCR will be in standby mode at this stage and the VCR display will show " ­ ­ : ­ ­". 1 2 VIDEO LINK AUTO COMMERCIAL Press the OPERATE button. " " will appear in the VCR display. VIDEO LINK CA (OPERATE) MENU = Exit During this time, if your set-up includes Scart connector and the TV is set to Scart input, the TV screen will display as shown. NK COMMERCIAL ADVANCE PROG VIDEO LINK CA 3 NK COMMERCIAL ADVANCE R PROG VIDEO LINK CA After this process is complete, the RF output channel will appear in the VCR display. For Example, RF output channel 35. 4 Switch on your TV and select an unused programme number, i.e. one not used for BBC1, ITV, etc. (Please consult your TV instruction manual as your TV may have a special VCR programme number which must be used.) Note: This programme number will be your VCR programme from now on. Tune your TV (consult your TV instruction manual) until the test pattern shown appears. The correct tuning position is when the picture is clear. Ensure this programme is stored in your TV. 5 6 COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION REV FWD If " " appears, press the stop button on the VCR or on the remote control handset. The RF channel data will appear in the VCR display. Press the PROG v or w button on the VCR to change the RF channel to " ". To stop the RF output, press the stop button on the VCR or on the remote control again. 11 SETTING UP (AUTO INSTALLATION FUNCTION) VCR TV If you cannot tune your TV correctly to the test signal, or if there is distortion in the signal, it may be necessary to change the VCR RF channel. In this case, press the PROG select button (v or w) on the VCR to change the VCR RF channel, and then retune your TV. If the test signal does not improve, continue to change the VCR RF channel and retune your TV until a clear test pattern is received. If the STOP button on the remote control or on the VCR is pressed, the RF from the VCR will be turned off. The VCR RF channel will change as follows: 7 REW FWD COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION 8 REW FWD COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION Press the play/still (6) button, the test pattern will disappear and the VCR will now come out of standby mode into operate mode. 9 REV FWD VIDEO LINK COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION VIDEO LINK CA Safety Tab You should now be able to playback a prerecorded cassette. Insert the cassette carefully (see page 21 for CASSETTE TAPES). If the safety tab is removed then playback will start immediately. If not, press the play/still (6) button and the picture will appear on the screen. 12 PRE-TUNING OF BUILT-IN TV TUNER REV FWD VIDEO LINK TAPE NAVIGATION REC/ IRT COMMERCIAL ADVANCE PROG VIDEO LINK CA Controls TV Screen 1 2 Turn on the TV and the VCR, then tune the TV to the video programme number. If you connect the VCR and TV using a 21-pin Scart connector lead, select the 21-pin Scart input of the TV. Press the MENU button. The menu, as illustrated, appears on the TV screen. MODE M ENU REV I EW CH VIDEO LINK NAV I COMMERCIAL ADVANCE PROG SAT OK VIDEO LINK CA SELECT MENU Exit 3 CH P R E S ET AUTO MANUAL NICAM ­ Press the cursor button to select the CH option, and press the ENTER button. The CH PRESET display, as illustrated, will appear on the TV screen. Exit SELECT OPERATE VCR/TV AUX OK MENU PROG 4 PROG TV PROG AUTO NAVI MENU MOVIE TEXT CA MENU Cursor MENU = Exit ENTER REC INDEX O LINK COMMERCIAL ADVANCE PROG REC IRT VIDEO LINK CA Press the ENTER button to select AUTO. The display, as illustrated will appear on the TV screen and " " will appear in the VCR display. The VCR will start auto tuning, auto channel mapping, auto clock setting, and auto RF seek function. It takes about 3 minutes. The following stations are stored in programme numbers 01 -- 05 automatically. 01 BBC1 02 BBC2 03 ITV 04 CH4 (or S4C) 05 CH5 Note: If the station does not transmit a signal which identifies itself, the station name will not appear. 5 IDEO LINK COMMERCIAL ADVANCE PROG VIDEO LINK CA Tune your TV (consult your TV instruction manual). The correct tuning position is when the picture is clear. After this process is complete, the test pattern will appear on the TV screen, and the RF output channel will appear in the VCR display. 6 REV FWD Press the PLAY/STILL button. The test pattern will disappear and the VCR change to the operate mode. COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION 7 REV FWD Press the PROG (5/) buttons to check the channels you can receive. COMMERCIAL ADVANCE PROG REC/ IRT TAPE NAVIGATION Note: If no channels have been set or a clear picture does not appear, check the aerial or scart connection. NK COMMERCIAL ADVANCE PROG REC/ IRT VIDEO LINK CA Note: When the pre-tuning of a channel is completed, the current time will appear in the VCR display. This is because the auto clock setting function has operated and the VCR clock has been set automatically. (See page 19 for details.) 13 SETTING UP The VCR should display "­ ­:­ ­" in it's LCD panel after the main supply is connected. (PRE-TUNING OF BUILT-IN TV TUNER) Deleting Unwanted Preset Channels 1 CH P R E S ET AUTO MANUAL NICAM