User manual HONEYWELL VISIONPRO IAQ

Operating Manual Mode d'emploi Manual de Uso VisionPRO IAQ ® Total Home Comfort System 69-1815EFS-1 BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen keys. To prevent damage to the thermostat, always press keys with your fingertip. Need Help? For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502 Read and save these instructions. ® U.S. Registered Trademark. US Patent No. 6,208,263; 6,373,376; 6,448,901; 6,926,076; D509151; H25192; H25193 and other patents pending. Copyright © 2006 Honeywell International Inc. All rights reserved. VisionPRO IAQ ® Table of contents About your new thermostat Programming at a glance ..................... 2 Quick reference to controls .................. 3 Quick reference to status display ........ 4 Clock setting.......................................... 5 Fan setting ............................................. 6 System setting....................................... 7 Energy Star settings .............................. 8 Using program schedules ..................... 9 Program schedule overrides .............. 10 Vacation hold ....................................... 12 Special features................................... 13 Screen lock .......................................... 14 Screen cleaning ................................... 15 Optional remote sensors .................... 16 Humidity control .................................. 17 Ventilation control................................ 19 Appendices Advanced functions ............................ 20 In case of difficulty .............................. 27 Limited warranty.................................. 29 Programming & Operation This thermostat is ready to go! Your new thermostat is preprogrammed and ready to go. See page 2 to check settings. CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). Operating Manual About your new thermostat Your new thermostat is pre-programmed and ready to go. Just set the time and day. Then check the settings below and change if needed: 1. Set clock........................................................................................................See page 5 2. Select fan setting: Preset to Auto ..............................................................See page 6 3. Select system setting: Preset to Heat ......................................................See page 7 4. Program schedules: Preset to energy-saving levels while you're at work or asleep (assumes you wake at 6 am, leave at 8 am, return at 6 pm and go to bed at 10 pm) ........................................................................ See pages 8-11 5. Set humification, dehumidification & ventilation controls, if applicable ............................................... See pages 17-19 ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time, and manually adjust the temperature (see pages 10-11). VisionPRO IAQ ® Quick reference to controls Press day(s) to set program schedule (see page 9) Press to select fan operation (see page 6) Press to select system type (see page 7) Press to adjust temperature settings (see pages 9-11) Press for more options MON FAN AUTO TUE WED THU FRI SAT SUN OK TO PICK MULTIPLE DAYS Inside 70 HOLD Set To 70 SYSTEM HEAT Following Schedule Press to set program schedule (see page 9) 6:01 SCHED AM CLOCK SCREEN MORE Press to override program schedule (see pages 10-11) Press to set clock (see page 5) Press to lock keypad for 30 seconds to clean screen (see page 14) Operating Manual Quick reference to status display Current inside temperature Current day of week Temperature setting WED FAN Fan setting System setting Current time Other display messages: · · · · · Inside AUTO 70 AM Set To 70 Recovery Program schedule on (does not display when off) Adaptive Intelligent Recovery in effect (see page 13) Inside humidity (If an outdoor sensor is installed, the outdoor temperature is shown instead of the humidity level. Press MORE to display the humidity level.) SYSTEM HEAT Following Schedule 6:01 SCHED 55 Humidity HOLD CLOCK SCREEN MORE Cool On: Cooling system is activated Heat On: Heating system is activated Aux Heat On: Auxiliary heating system is activated Wait: Compressor protection activated (see page 13) Screen Locked: See page 26 to unlock VisionPRO IAQ ® Clock setting Inside FAN AUTO WED Press CLOCK 70 WED HOLD Set To 70 6:01 SCHED FAN AUTO AM To set the current time display, press CLOCK, then press s or t to adjust the time. Press and hold s or t to advance the time more quickly. Press DONE to save & exit (or press CANCEL to exit without changing the time). Note: The real-time clock should never require adjustment since it automatically updates for daylight savings time, and stores all date/time information. Note: To change the current week day display, see page 21. CANCEL CLOCK SCREEN MORE Inside Adjust time, then press DONE 70 Set To 70 6:02 DONE AM Operating Manual Fan setting WED FAN AUTO Press FAN to select fan operation: Set To Inside 70 AM 70 · On: Fan is always on. · Auto: Fan runs only when the heating or cooling system is on. · Circ: Fan runs randomly, about 35% of the time. Use this setting for improved air circulation, or for more efficient air cleaning, if you do not want the fan to run all the time. You can press FAN to override the fan settings you've programmed for different time periods (see page 9). If you select On or Circ, the setting you select will remain active until you press FAN again to select Auto, and return to the fan schedule. SYSTEM HEAT Following Schedule 6:01 SCHED HOLD CLOCK SCREEN MORE Press FAN Note: If a fan schedule is programmed, "Auto" will run the fan schedule. VisionPRO IAQ ® System setting WED FAN AUTO Press the SYSTEM button to select: Set To Inside 70 AM 70 · Heat: Thermostat controls only the heating system. · Cool: Thermostat controls only the cooling system. · Off: Heating and cooling systems are off. · Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature. · Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Auxiliary Heat. Compressor is not used. SYSTEM HEAT Following Schedule 6:01 SCHED HOLD CLOCK SCREEN MORE Press SYSTEM Operating Manual EnergyStar settings for maximum cost savings ® It's easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for each day. This thermostat is pre-set to use EnergyStar program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.) ® Heat (Mon-Fri) Wake (6:00 am) Leave (8:00 am) Return (6:00 pm) Sleep (10:00 pm) Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun) 70 ° 62 ° 70 ° 62 ° 78 ° 85 ° [Or cancel period] 78 ° 82 [Or cancel period] ° 70 ° 62 ° 70 ° 62 ° [Or cancel period] [Or cancel period] 78 ° 85 ° 78 ° 82 ° FAN AUTO Inside To adjust program schedules WED 70 HOLD Set To 70 70 VisionPRO IAQ ® Following Schedule FAN AUTO Press SCHED Inside 6:00 70 AM Set To SCHED CLOCK Following SCREEN MORE Schedule Press EDIT DONE EDIT 6:00 WAKE AM LEAVE RETURN SLEEP CANCEL Select day(s) MON FAN AUTO Set heat/cool levels WED THU FRI SAT SUN TUE OK TO PICK MULTIPLE DAYS 70 CANCEL PERIOD HEAT 1. Press SCHED, then EDIT. 2. Press day buttons (MON-SUN) to select day(s). 3. Press s or t to set your Wake time for selected day(s). 4. Press s or t to set Heat and Cool temperature for this time period. 5. Press other time periods (LEAVE, RETURN, SLEEP) to set time and temperatures for each. 6. Press DONE to save & exit (or press CANCEL to exit without saving changes). Note: You can press CANCEL PERIOD to eliminate any unwanted time period. 6:00 DONE WAKE AM 78 LEAVE RETURN SLEEP COOL CANCEL Note: Press FAN to customize fan settings for any time period (see page 6). Set time for program period to start Operating Manual Program schedule override (temporary) Adjust temperature WED FAN AUTO Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. The new temperature will be maintained only until the time you set. When the timer expires, the program schedule will resume and set the temperature to the level you've programmed for the current time period. To cancel the temporary setting at any time, press CANCEL (or SCHED). The program schedule will resume. Inside 70 AM Set To 73 HEAT Heat On SYSTEM HEAT Hold Temperature Until 8:00 HOLD 78 CLOCK SCREEN MORE COOL SCHED CANCEL Press to set timer Press CANCEL (or SCHED) to resume program schedule 0 VisionPRO IAQ ® Program schedule override (permanent) Press HOLD Adjust temperature WED FAN AUTO Press HOLD to permanently adjust the temperature. This will turn off the program schedule. Whatever temperature you set will be maintained 24 hours a day until you manually change it or press CANCEL (or SCHED) to cancel "Hold" and resume the program schedule. Inside 70 AM Set To 73 Heat On SYSTEM HEAT 8:00 Permanent Hold SCHED HOLD CLOCK SCREEN MORE CANCEL Press CANCEL (or SCHED) to resume program schedule Operating Manual Vacation hold 1WED temperature Set FAN AUTO Inside 70 PM Set To 55 This feature can suspend the program schedule for extended periods of time. Press s or t to set the temperature you want, then press s or t to set the time of day you want the schedule to resume when you return. Press HOLD twice, then press s or t to select the number of days. CANCEL SYSTEM HEAT Hold Temperature Until 6:00 SCHED HOLD CLOCK SCREEN MORE WED FAN 2 Press to set time for Set To schedule to resume 3 AUTO Press HOLD twice Inside 70 14 HOLD 55 Whatever temperature you set will be maintained 24 hours a day for the number of days you select. After this number of days have elapsed, the previously programmed schedule will resume at the time you set. If you return earlier than expected, press CANCEL (or SCHED) to cancel "Hold" and resume the program schedule. SYSTEM HEAT Hold Temperature Until DAYS SCHED CLOCK SCREEN MORE CANCEL 4 Press to select number of days VisionPRO IAQ ® Special features Auto Changeover: When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Adaptive Intelligent Recovery: This feature allows the thermostat to "learn" how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set. Compressor Protection: This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage. During the wait time, the message "Wait" is displayed on screen. Flashing message: Reminder to replace filter or UV lamp. After replacement, press RESET to reactivate the alert timer. Southern Away Dehumidification: Your system may be programmed to control humidity while your house is vacant during the humid season. Before you leave the house, press the HOLD button three times to activate this feature. This will control temperature and humidity to help protect your house and possessions while you are away. (If this feature does not work, contact your installer.) Operating Manual Screen lock WED FAN AUTO Inside 70 PM SCREEN LOCKED To prevent tampering, the screen can be partially or fully locked. When partially locked, the screen displays SCREEN LOCKED for several seconds if a locked key is pressed. When the screen is fully locked, no keys function. To lock or unlock the screen, see advanced function 0670 on page 26. Set To 70 SYSTEM HEAT Following Schedule 6:00 SCHED 43 CLOCK SCREEN MORE HOLD See advanced function 0670 (page 26) for screen lock options WED VisionPRO IAQ ® Screen cleaning FAN Inside AUTO Press SCREEN 70 HOLD SCREEN LOCKED Set To 70 Press SCREEN to lock the screen for cleaning. The screen will remain locked for 30 seconds so you can clean the screen without changing any settings. After 30 seconds, press DONE to resume normal operation, or press SCREEN again if you require more time for cleaning. Note: Do not spray any liquid directly on the thermostat. Spray liquids onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers. Following Schedule 6:00 SCHED PM CLOCK SCREEN MORE Screen lock timer (30 seconds) 30 SCHED HOLD OK TO CLEAN SCREEN CLOCK SCREEN MORE Operating Manual Optional remote sensors WED FAN AUTO If an outdoor sensor is installed, the current outdoor temperature is displayed. Set To Inside 70 AM 70 Outside SYSTEM HEAT Following Schedule If an indoor remote sensor is installed, the display shows the indoor temperature at the location of the sensor. If more than one indoor sensor is installed, the display shows an average of temperature readings from all sensors or an average between the thermostat and the sensor(s). 6:01 SCHED 43 CLOCK SCREEN HOLD MORE Inside temperature Outside temperature VisionPRO IAQ ® Humidification control Set Frost Control & humidity level Press MORE until the humidifier screen is displayed, then press s or t to set the humidity and Frost Control level. When using Frost Protection, if frost/condensation appears on windows, lower the frost setting. Wait at least 1 day before adjusting the frost level again. Once frost no longer appears, the thermostat will control humidity to the maximum level without frosting or fogging windows and without further adjustment. Press DONE to save and exit, or press CANCEL to exit without saving changes. Note: If you do not have an outdoor temperature sensor, the Frost Control level will not be displayed. Inside 32 5 FROST DEHUMIDIFIER 55 DONE CANCEL Press to save & exit Operating Manual Dehumidification control Press to select Auto or Off Press to set desired humidity Press MORE until the dehumidifier screen is displayed, then press s or t to set the desired humidity level and operation (Auto or Off). If installed to control a dehumidifier, the thermostat can activate it as needed to reduce humidity. Inside 73 DEHUMIDIFIER AUTO DONE 55 CANCEL If you don't have a dehumidifier, the thermostat activates the air conditioner to reduce humidity (may cool as much as 3°F lower than your temperature setting). Press DONE to save and exit, or press CANCEL to exit without saving changes. Press to save & exit Note: Auto/Off only present when using a whole house dehumidifier (not present when dehumidifying with A/C). VisionPRO IAQ ® Ventilation control Press to set ventilation timer You can ventilate your home at any time: Press MORE until the ventilation screen is displayed, then press s or t to set the ventilation timer. You can set the timer to ventilate from 20 to 180 minutes, in 20-minute increments. To turn off the ventilator, select 0. AUTO DONE VENT 40 Minutes Press DONE to save and exit, or press CANCEL to exit without saving changes. CANCEL If programmed for auto-ventilation by the installer, the thermostat will ventilate your home as needed. Auto/Off will turn off/on the automatic ventilation only. Ventilation can still be requested by using the timer when set to Off. Press to save & exit Operating Manual TUE FAN AUTO Advanced functions 1 Press SYSTEM. TUE FAN AUTO Inside 2 Press and hold 70 AM Set To 70 Inside 70 AM blank center key until the display changes. SYSTEM HEAT 6:01 TUE