BeverageMateTM Assembly Instructions These instructions have been prepared to make the assembly of the BeverageMateTM center easy and quick. If you follow these instructions you will need only slot head and phillips head screwdrivers to assemble the entire cabinet. Before you begin, please read the entire instructions sheet carefully and using the parts list, make sure you have all the parts and hardware necessary to complete the assembly. Pre-Assembly The BeverageMateTM has a number of assembly steps which, if done before the actual assembly begins, will reduce time and make the project much easier. Please follow the steps carefully. IMPORTANT Remove serving tray from slot and set aside. Step 3. Turn Bottom right side up (on casters). Locate 8 pre-drilled holes. Insert threaded end of Cam-Lock pins and tighten into holes with screwdriver. Step 1. Turn Top upside down. Locate 8 pre-drilled holes. Insert threaded end of Cam-Lock pins and tighten into holes with screwdriver. Step 4. Find 2 sides of BeverageMateTM. Find 2 hinge mounting brackets. Locate 2 pre-drilled holes on each side. Position brackets over pre-drilled holes and using screws secure tightly. Step 2. Turn Bottom upside down. Locate 4 pre-drilled holes in each corner. Position caster plate over holes. Insert and tighten screws through each hole. Repeat steps for each caster. Step 5. Find 2 door panels. Find 2 hinge assemblies. Locate 2 pre-drilled holes and hinge seat, on each door. Insert hinge assembly into hinge seat with hinge holes over pre-drilled holes in door. Using screws secure tightly. Holding by end, fold hinge arm down. CAUTION Hinges arms are spring loaded, fold down carefully. Cabinet Assembly Step 6. Standing Top on it's front (slotted edge down), position the 2 center panels on edge. Line up the 2 pre-drilled holes on the top of each panel and insert them onto the center Cam-Lock pins. Insert locking nut into pre-drilled hole and rotate 1/2 turn or until tight. Repeat for each Cam-Lock pin. Step 8. Insert back into mortised grooves on sides and slide in until it fits into mortised groove on top. Step 9. Line up pre-drilled holes on bottom of sides and divider panels with 8 Cam-Lock pins on bottom. Insert pins into holes. IMPORTANT After Step 9, rotate BeverageMate onto one side. Step 7. Position the 2 side panels on edge and line up pre-drilled holes with remaining Cam-Lock pins. Insert pins into holes. Insert locking nut into pre-drilled hole and rotate 1/2 turn or until tight. Repeat for each Cam-Lock pin. Step 10. Insert Cam-Lock locking nuts into pre-drilled holes and rotate 1/2 turn or until tight. IMPORTANT After Step 10, rotate BeverageMate up on casters. Note Cam-Lock assembly detail on last page. Door Assembly Shelf Assembly Step 11. Insert leveling screw in hinge mounting bracket through hole in hinge arm. Step 15. Locate 2 pre-drilled holes on each door. Position door handle on front of door over holes. Using wood screws, secure handles to doors. IMPORTANT Re-insert serving tray into slot under Beverage Mate top. Step 12. Using screwdriver, slightly tighten screw to hold door in place. Repeat procedure for all 4 hinges. Step 16. Insert 8 shelf support pins into pre-drilled holes. All 4 pins which support each shelf should be level. Step 13. Close both doors and look at how they line up. Using the leveling set screw (front), loosen or tighten to level the doors from side to side. Step 17. Turning each shelf at a slight angle insert into cabinet and position on shelf support pins. IMPORTANT If shelf does not rest flat on pins raise shelf, remove pins, reposition into hole, and lower shelf. Step 14. Using the rear set screw, loosen and move the hinge in or out to adjust the tightness of the door against the cabinet. When doors are properly adjusted, re-tighten screws. Your BeverageMateTM cabinet is complete and now ready for use. Parts List Cabinet Components 1. (1) Serving Tray 2. (1) Pre-assembled Top 3. (1) Bottom 4. (2) Oak Laminate Side Panels 5. (2) Divider Panels 6. (1) Back Panel 7. (2) Oak Laminate Door Panels 8. (2) Door Handles 9. (4) Casters 10. (2) Shelves Hardware 11. (16) Cam Locking Pins 12. (16) Cam Locking Nuts 13. (32) Wood Screws 14. (4) Door Hinge Assemblies 15. (8) Shelf Support Pins 16. (4) Door HandleScrews Cam Locking Pins and Nuts Make Assembling the BeverageMateTM Quick and Easy. The Cam Locking System utilized in the BeverageMateTM is simple and fast and secures large panels better than traditional methods. The Cam Locking Pins are threaded into pre-drilled holes and secured. The locking end of the pin is inserted into a panel with a pre-drilled hole. The side of the panel has a large hole which exposes the end of the cam locking pin. The Cam Locking Nut is inserted into the hole and using a screwdriver turned clockwise. The cam action of the nut tightens and locks the pin into a secure position. ...