INSTRUCTION MANUAL BEFORE INSTALLATION 1 2 3 4 5 6 7 AP-12 WIRELESS ACCESS POINT OBTAINING AN IP ADDRESS FROM THE DHCP SERVER FIXED IP ADDRESS SETTING AP-12 MANAGER SETTING EXAMPLES IP CONFIGURATION REFERENCES INTRODUCTION IMPORTANT ii IMPORTANT When connecting the AP-12 to a bridging type modem (or in bridging mode) directly, a global IP address may be assigned to the AP-12 from the modem, according to the modem settings. When a global IP address is assigned to the AP-12, an illegal operator, such as a cracker, a hacker, may access it. To avoid such access, connect a router between the modem and the AP-12. The bridge type modem assigns a global IP address to the connected PC (only one). The router type modem assigns a private IP address (e.g.192.168.x.x) to the connected PCs via the HUB by the built-in routing function. The AP-12 can be connected to a router type modem directly. Contact your Internet Service Provider (ISP) if you do not know your modem type. About exchanging the AP-12 or the PC connected to the AP-12. The AP-12 memorizes the communication settings between the AP12 and the connected PC. Thus, if the AP-12 and/or the PC connected to it changed, communication may fail. In such case, turn the AP-12 power OFF. After waiting a few seconds, turn the power ON again. INTRODUCTION FOREWORD Thank you for purchasing the Icom Wireless Access point AP-12. This wireless access point is provided with the functions necessary for supporting a wireless LAN. This manual is designed to help you use the product to its fullest potential. Read this manual carefully before using the product. TRADEMARK CREDITS Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other countries. Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries. The screen shots that appear in this manual are used with permission of Microsoft Corporation. Other product and company names mentioned herein are trademarks or registered trademarks of their respective owners. iii INTRODUCTION INTRODUCTION iv FEATURES " Up to 11 Mbps data transmission rate with automatic fallback function (11/5.5/2/1 Mbps). " The supplied utility software, [AP-12 Manager] allows you simple setup of the system with a step-by-step tutorial. Windows XP, Windows Me, Windows 98SE, Windows 98, Windows 2000 are supported. " The diversity antenna is built into the compact body to provide stable communication. " Versatile operating modes for Access Point mode, Bridge mode A (Peer-to-Peer), Bridge mode B (Client mode), and Bridge mode C (Multi-site). A roaming function is also available while in Access Point mode. It provides full mobility and seamless network access from anywhere within the area for the connected clients. " The DHCP client function is available to automatically obtain the network configuration such as the IP address (This is not activated in Bridge mode B mode operation). " Data can be protected with high-level security function such as 128/64-bit WEP (Wired Equivalent Privacy) encryption and MAC address registration. " AP-12 uses a direct spread-spectrum communication system which ensures stabilized communication even under influence of noise and interference. INTRODUCTION FCC INFORMATION AP-12 Tested to comply with FCC standards FOR HOME OR OFFICE USE CAUTION: Changes or modifications not expressly approved by Icom Inc. could void the user's authority to operate this Access Point. Class B digital device users; This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. RF EXPOSURE SAFETY INFORMATION: CAUTION: To comply with the FCC RF exposure requirements, this transmitter (builtin antenna) must be fixed-mounted on permanent structures with a separation distance of at least 8 inches (20cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. For CANADA only Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. v INTRODUCTION INTRODUCTION vi GENERAL PRECAUTIONS " If a connection cable is disconnected or has a loose connection during operation, an error may occur. Connect the connectors correctly, and do not touch the connectors during operation. " For the operation of PC and peripheral devices, follow the instructions provided in the manuals which come with the PC and peripheral devices. " This device may cause signal interference when used in a domestic setting. When interference occurs, move this unit as far as possible away from the affected device. " The CD which comes with the AP-12 is for the AP-12 only. Do not use it for any other devices. " Icom Inc. is not responsible for any interference that arises by incorporating a configuration file for the AP-12 or a firmware update data file, which is available on our home page, into any device other than the AP-12. Moreover, Icom Inc. is not responsible for any interference that arises by modifying or disassembling the AP12. Furthermore, Icom Inc. is not responsible for any damages, lost profits or third party's claim resulting from any missed communication or telephone call due to the AP-12's fault, error, malfunction, breakage, data loss or any other external factor such as power failure. " All copyrights associated with this manual and all intellectual property rights associated with the hardware and software of the AP-12 are held by Icom Inc. " Unauthorised reproduction or transmission of this manual, or any part hereof, is prohibited. " The content of this manual, the hardware and software associated with the AP12, and the appearance of the AP-12 are all subject to change without notice. Notational Conventions The following notational conventions are used in this manual: · The names of utilities, menus, windows, tabs, icons, text boxes, and check boxes are enclosed in square brackets ([ ]). · The names of command buttons within dialog boxes are enclosed in less-than and greater-than signs (< >). - Windows 98 SE represents the Windows 98 Second Edition. Windows Me represents the Windows Millennium Edition. - The contents of windows appearing in this manual may vary depending on the operating system installed on your PC. ACCESSORIES I Supplied accessories AP-12 Patch cable 3 m (9.8 feet) AP-12 Main Unit Crossover cable 1 m (3.2 feet) CD Leg Pad Fixing Sheet AC Adapter Instruction Manual Registration Card Warranty Card · Leg Pad ........................ · Fixing sheets .................. Attach to the bottom of the AP-12 to secure. Attach to the bottom of the AP-12 to secure. Remove the protective paper before attaching the sheet. For connection between the AP-12 and a PC. For network connection between the AP-12 and HUB. [AP-12 Manager] is included. The adapter for the AP-12. · Crossover cable............... · Patch cable..................... · CD .............................. · AC Adapter ..................... vii TABLE OF CONTENTS TABLE OF CONTENTS viii IMPORTANT ..........................................................................................ii INTRODUCTION ....................................................................................iii ACCESSORIES ....................................................................................vii TABLE OF CONTENTS ........................................................................viii SAFETY PRECAUTIONS ........................................................................x Chapter 1 BEFORE INSTALLATION ....................................1­8 1-1 1-2 1-3 1-4 1-5 Wireless functional modes ..........................................2 Unit description .........................................................4 Accessory attachment ................................................5 Installation location ......................................................7 About the Ethernet card................................................8 Chapter 2 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER.................................9­14 2-1 Connecting to a LAN ................................................10 2-2 Installing [AP-12 Manager] ..........................................11 2-3 Starting [AP-12 Manager] ..........................................13 Chapter 3 FIXED IP ADDRESS SETTING ...........................15­29 3-1 3-2 3-3 3-4 Connecting to the PC ................................................16 Using [Easy Setting Wizard] .......................................17 Installing [AP-12 Manager] ..........................................25 Starting [AP-12 Manager] ..........................................27 Chapter 4 AP-12 MANAGER ..........................................31­44 4-1 [AP-12 Manager] screen descriptions ...........................32 4-2 The default settings ...................................................43 4-3 Uninstalling [AP-12 Manager].......................................44 Chapter 5 SETTING EXAMPLES .......................................45­49 5-1 5-2 5-3 5-4 Access point Bridge mode Bridge mode Bridge mode mode ...................................................46 A (Peer-to-Peer) ....................................47 B (Client Mode) .......................................48 C (Multi-site) ..........................................49 TABLE OF CONTENTS Chapter 6 IP CONFIGURATION .......................................51­56 6-1 For Windows XP ......................................................52 6-3 For Windows 98/98SE/Me ..........................................54 6-2 For Windows 2000 ...................................................55 Chapter 7 REFERENCES ................................................57­71 7-1 Troubleshooting ......................................................58 7-2 Connecting the AP-12 and HUB .................................60 7-3 Verifying the connection to the AP-12 ...........................60 7-4 Failure in searching for the AP-12.................................61 7-5 IP address confirmation .............................................64 7-6 Connection to the router type modem ...........................66 7-7 Specifications .........................................................68 7-8 Glossary ..................................................................70 ix SAFETY PRECAUTIONS SAFETY PRECAUTIONS x Be sure to read these precautions in order to use the AP-12 safely. · These precautions are intended to ensure that the access point is operated safely and correctly. Follow these instructions to avoid property damage and prevent personal injury to yourself (user) or others in the vicinity. · Before reading the rest of this manual, read and understand the precautions listed under "RWARNING" and "RCAUTION". · After reading this manual, store it in a convenient place for future review. I Wireless Access Point RWARNING Failure to observe the precautions listed here could result in serious or fatal injury to the user or those near the user. G This unit does not require adjustment. Do not disassemble or modify the unit or attempt to repair it yourself. Otherwise fire, electric shock, or equipment failure may result. G Do not install in a location where the unit can easily become wet (such as adjacent to a humidifier). Otherwise fire, electric shock, or equipment failure may result. G Do not handle the unit with wet hands. Otherwise electric shock may result. G Discontinue use immediately and unplug the power cable from the AC receptacle if the unit emits smoke, an abnormal odor, or an abnormal noise or if water enters the unit. Otherwise fire, electric shock, or equipment failure may result. Disconnect the plug of the AC adapter and all other cables from the unit. Confirm that the smo ...