User manual ICOM IC-A24

INSTRUCTION MANUAL VHF AIR BAND TRANSCEIVER iA24 iA6 This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. IC-A24 IC-A6 SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as "Occupational Use Only", meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is W ARN ING NOT intended for use by the "General Population" in an uncontrolled environment. This radio has been evaluated for compliance at the distance of 2.5 cm with the FCC RF exposure limits for "Occupational Use Only". In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: · FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. · American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. · American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields­ RF and Microwave. · The following accessories are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.; Belt Clip (MB86/103), Rechargeable Ni-MH Battery Pack (BP-210N) and Alkaline Battery Case (BP-208N). To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: · DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. · DO NOT transmit for more than 50% of total radio use time ("50% duty cycle"). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when " " appears on the function display. You can cause the radio to transmit by pressing the "PTT" switch. · ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clips which are listed on page 31 when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. C AU TIO N i FOREWORD Thank you for purchasing this Icom product. The IC-A24/A6 VHF AIR BAND TRANSCEIVER is designed and built with Icom's state of the art technology and craftsmanship. With proper care this product should provide you with years of trouble-free operation. SUPPLIED ACCESSORIES Accessories included with the transceiver: Qty. q Antenna .......................................................................... 1 w Belt clip ........................................................................... 1 e Handstrap ....................................................................... 1 r Battery pack* or battery case .......................................... 1 t Wall charger* .................................................................. 1 y Carrying case* ................................................................ 1 u Headset adapter* ........................................................... 1 * The battery pack, wall charger, headset adapter or carrying case may differ depending on version. Some versions do not include a battery pack, wall charger, headset adapter or carrying case. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-A24/A6. q w e r EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. WORD t y u ii PRECAUTION R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (231/32 to 315/16 inch) away from the lips and the transceiver is vertical. DO NOT allow children to play with any radio equipment containing a transmitter. DO NOT operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discontinue use. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below ­10°C (+14°F) or above +60°C (+140°F). The use of non-Icom battery packs/chargers may impair transceiver performance and invalidate the warranty. Even when the transceiver power is OFF, a slight current still flows in the circuits. Remove the battery pack or case from the transceiver when not using it for a long time. Otherwise, the battery pack or installed dry cell batteries will become exhausted. NEVER connect the transceiver to an AC outlet or to a power source of more than 11.5 V DC. Such a connection will damage the transceiver. NEVER connect the transceiver to a power source that is DC fused at more than 5 A. Accidental reverse connection will be protected by this fuse, higher fuse values will not give any protection against such accidents and the transceiver will be ruined. NEVER short the terminals of the battery pack. Also, current may flow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carrying in handbags, etc. iii FCC caution: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. (U.S.A. only) Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. TABLE OF CONTENTS SAFETY TRAINING INFORMATION ............................................... i FOREWORD ................................................................................... ii IMPORTANT .................................................................................... ii EXPLICIT DEFINITIONS ................................................................. ii SUPPLIED ACCESSORIES ............................................................ ii PRECAUTIONS............................................................................... iii TABLE OF CONTENTS ................................................................. iv 1 PANEL DESCRIPTION ........................................................ 1 ­ 6 I Panel description ................................................................... 1 I Function display ..................................................................... 5 ACCESSORY ATTACHMENT .................................................. 7 BASIC OPERATION .......................................................... 8 ­ 11 I Setting a frequency ................................................................ 8 I Setting a squelch level ........................................................... 8 I Selecting a weather channel................................................... 8 I Receiving ............................................................................... 9 I Transmitting ........................................................................... 9 I ANL function ........................................................................... 9 I Low battery indicator ............................................................ 10 I Recall function ..................................................................... 10 I Setting weather alert function................................................ 11 I Accessing 121.5 MHz emergency frequency ....................... 11 I Lock function ........................................................................ 11 I Side tone function ................................................................ 11 I Setting beep tone ................................................................. 11 MEMORY OPERATION ................................................... 12 ­ 15 I Memory channel selection ................................................... 12 I Transferring memory contents ............................................. 12 I Programming a memory channel ......................................... 13 I Memory names .................................................................... 14 I Clearing the memory contents ............................................. 14 5 SCAN OPERATION ......................................................... 16 ­ 17 I Scan types ........................................................................... 16 I COM band scan ................................................................... 16 I Memory scan ....................................................................... 16 I Weather channel scan (U.S.A. version only) ............................ 17 I "TAG" channels ................................................................... 17 VOR NAVIGATION (IC-A24 only) .................................... 18 ­ 24 I VOR indications ................................................................... 18 I VOR functions ...................................................................... 19 I Flying to a VOR station ........................................................ 20 I Entering a desired course .................................................... 22 I Crosschecking position ........................................................ 22 I Duplex operation (U.S.A. version only) .................................... 24 BATTERY PACKS ........................................................... 25 ­ 27 I Battery charging ................................................................... 25 I Battery cautions ................................................................... 25 I Optional battery case ........................................................... 26 I Optional battery chargers ..................................................... 27 CLONING ................................................................................ 28 TROUBLESHOOTING ............................................................ 29 6 2 3 7 8 9 10 SPECIFICATIONS .................................................................. 30 11 OPTIONS ................................................................................ 31 12 QUICK REFERENCE ...................................................... 32 ­ 33 13 OPTIONAL HEADSET CONNECTION .................................. 34 4 iv 1 PANEL DESCRIPTION IC-A24 WX-ALERT I Panel description e r t y u i w o IC-A6 !7 q !7 !6 !5 Speaker !0 !1 !2 !3 Microphone WX-ALERT !4 !7 1 PANEL DESCRIPTION q BACKLIGHT SWITCH [LIGHT] Turns the backlight for display and keypad ON or OFF. w PTT SWITCH [PTT] (p. 9) Push and hold to transmit; release to receive. ·" " appears on the function display while transmitting. 1 1 u SQUELCH KEY [SQL·WX-ALERT] (p. 8) Push [SQL·WX-ALERT], then rotate [DIAL] to select the squelch level. · 24 squelch levels and squelch open (0) are available. Push , then push [SQL·WX-ALERT] to turn the WX-alert function ON or OFF. i POWER SWITCH [PWR] (pgs. 9, 28) Push and hold for 2 sec. to turn the power ON or OFF. While pushing and holding [MR·MW], push [PWR] to enter the cloning function mode. o EXTERNAL SPEAKER AND MICROPHONE JACKS [MIC/SP] (p. 34) Connects an OPC-499 HEADSET ADAPTER and headset, if desired. !0 FUNCTION KEY [ ] Push to call up the function indicator, " ", then push another key to access its secondary function. ·" " appears for 3 sec. after is pushed; at this time pushing again cancels the indication. e VOLUME [VOL] (p. 9) Adjusts the audio level. r TUNING DIAL [DIAL] (pgs. 8­12) Rotate [DIAL] to select the desired frequency, WX channel number, BANK number and memory channel. Rotate [DIAL] to set the squelch level and beep tone level. t ANTENNA CONNECTOR [ANT] (p. 7) Connects the supplied antenna. y RECALL CHANNEL UP/DOWN KEYS []/[] (p. 10) Push to enter the recall function mode. Push to call the stored frequency in the recall mode. Push , then push []/[]to replace stored recall frequencies to back or front. NOTE: In general, " " disappears when another key is pushed to activate a secondary function. However, some keys which have more than one secondary function, (such as [DUP]), do not cancel " ". In this case, " " disappears automatically after 3 sec. 2 1 PANEL DESCRIPTION !6 ENTER KEY [ENT·WX] (pgs. 8, 14) Push to enter the numeral input. Enters consecutive zero digits. (p. 8) Push , then push [ENT·WX] to enter the weather channel selection mode (U.S.A. version only). (p. 8) Push to program the memory name. (p. 14) NOTE: Some functions may not be available depending on versions. Ask your authorized dealer for details. · DC POWER CONNECTION !1 CLEAR KEY [CLR·DEL] (pgs. 8­17) Push to turn to the frequency mode, when memory channel, WX channel, 121.5 MHz, squelch level setting or beep tone setting is selected. Push , then push and hold [CLR·DEL] to delete a recall frequency data. Push to clear the entered comment of memory name while programming. Push to stop the scan function to turn to the frequency mode while the scan function is operating. !2 ANL KEY [ANL·SCAN] (pgs. 9, 16, 17) Push to turn the ANL function ON or OFF. Push , then push [ANL·SCAN] to start the scan function. !3 EMERGENCY KEY [121.5 MHz] (p. 11) Push for 2 sec. to select the 121.5 MHz emergency frequency. !4 DC POWER JACK Connect the AC adapter or optional cable to charge the battery pack or to operate by external power supply. (see right illustration) !5 MEMORY MODE KEY [MR·MW] (pgs. 12­15) Push to call the memory channel mode. Push , then push [MR·MW] to program the contents into the memory channels. 3 R CAUTION ! · DO NOT modify the CP-20. A modification could cause a fire or electrocution. · BE CAREFUL not to cut or fray the CP-20's IC-A24/A6 power cable when disconnecting/connecting the CP-20 from/to the cigarette lighter socket. CP-20 (for 11 24 V) (optional) To the cigarette To [DC 11V] lighter socket Wall charger PANEL DESCRIPTION !7 DIGIT KEYS Input the specified digit during frequency input, memory channel selection, etc. In addition, each key has one or more secondary function after pushing as follows: Push , then push [0·BANK], and rotate [DIAL] to select the memory BANK number during the memory operation. (p. 12) Push , then push [1·DVOR] to select the DVOR display from the CDI display in NAV band. (p. 19)*1 Push , then push [2·TO] to change the course indicator characteristics to "TO" flag in the DVOR display in NAV band. (p. 19)*1 Corrects the deviation while using "TO" flag.*1 Push , then push [3·FROM] to change the course indicator characteristics to "FROM" flag in the DVOR display in NAV band. (p. 19)*1 Corrects the deviation while using "FROM" flag.*1 Push , then push [4·CDI] to select the CDI display from the CDI display in NAV band. (p. 19)*1 1 1 Push , then push [5·DUP-W] to set the duplex frequency in NAV band for U.S.A. version only. (p. 24)*1 Push , then push [6·DUP] to turn the duplex function ON and OFF in NAV band for U.S.A. version only. (p. 24)*1 Push , then push [7· ] to turn the key lock function ON and OFF. (p. 11) Push , then push [8·BEEP] to turn the beep tone setting mode ON. (p. 11) · Adjustable level; 0 to 9 Push , then push [9·TAG] to set the displayed memory or weather channel as a "TAG" channel. (p. 17) *1 These functions available on the IC-A24 only. 4 1 PANEL DESCRIPTION I Function display q FUNCTION INDICATOR (p. 2) Appears when is pushed. w TX INDICATOR (p. 9) Appears while transmitting. q w e r t y e RX INDICATOR (p. 9) Appears when receiving a signal or when the squelch opens. u !5 !4 i o r DUPLEX INDICATOR (IC-A24 only) (p. 24) "DUP" appears when the duplex function is activated in NAV mode. "DUP" blinks while setting the duplex frequency. t LOW BATTERY INDICATOR (p. 10) Appears when the battery is nearing exhaustion. The attached battery pack requires recharging. Appears and flashes when battery replacement is necessary. y LOCK INDICATOR (p. 11) Appears while the lock function is in use. u FREQUENCY DISPLAY (pgs. 8, 14) Shows the operating frequency. Shows the channel name when the memory name function is selected. !1 !3 !2 !1 !0 5 PANEL DESCRIPTION 1 1 i TAG CHANNEL INDICATOR (p. 17) " " appears when the selected memory channel is set as a TAG channel. o MEMORY CHANNEL INDICATOR (pgs. 12­15) Shows the selected memory channel number. !0 MEMORY BANK NUMBER INDICATOR (p. 12) Shows the selected memory bank number. !1 OVERFLOW INDICATOR (IC-A24 only) (pgs. 18­22) Appears when the deviation between the desired course and flying course is over 10 degrees. !2 ANL INDICATOR (p. 9) Appears while the ANL (Automatic Noise Limiter) function is in use. !3 COURSE DEVIATION NEEDLES (IC-A24 only) (pgs. 18­22) Indicates the deviation between the desired course and your actual flying course every 2 degrees. !4 COURSE INDICATORS (IC-A24 only) (p. 19) Indicates where your aircraft is located on a VOR radial in DVOR mode. Indicates where your desired course is located on a VOR radial in CDI mode. !5 TO-FROM INDICATOR (IC-A24 only) (p. 19) Indicates whether the VOR navigation information is based on a course leading to the VOR station or leading away from the VOR station. 6 2 ACCESSORY ATTACHMENT D Belt clip Conveniently attaches to your belt. Attach the belt clip with the supplied screws as below. NOTE: Use the supplied screws only. D Antenna CAUTION: DO NOT transmit without an antenna. Otherwise the transceiver may be damaged. Insert the supplied antenna into the antenna connector and screw down the antenna as shown below. Supplied screws D Battery pack replacement Before replacing the battery pack, push [PWR] for 2 sec. to turn the power OFF. Slide the battery release button forward, then pull the battery pack upward with the transceiver facing away from you. 7 BASIC OPERATION I Setting a frequency ï Using keypad q Push [PWR] for 2 sec. to turn power ON, then push [CLR·DEL] to select the frequency mode when memory CH number or WX CH number appears on the function display. w Push 5 appropriate digit keys to input the frequency. · Push [1·DVOR] as the 1st digit. · When a wrong digit is input, push [CLR·DEL] to clear, then repeat step w again. · Push [ENT·WX] to enter consecutive zero digits. · Only [2·TO], [5·DUP-W], [7· ] and [0·BANK] can be entered as the 5th and final digit. [EXAMPLE] · 111.225 MHz: Push · 117.250 MHz: Push · 120.000 MHz: Push · 125.300 MHz: Push 3 2 3 I Setting a squelch level The transceiver has a noise squelch circuit to mute undesired noise while receiving no signal. q Push [SQL·WX-ALERT], then rotate [DIAL] to select the squelch level. · `SQL--0' is open squelch and `SQL--24' is tight squelch. · Appears " " while the squelch is open. w Push [SQL·WX-ALERT] or [CLR·DEL] to exit the squelch set mode. I Selecting a weather channel (U.S.A. version only) The U.S.A. version has VHF marine WX (weather) channel receiving capability for flight planning. q Push , then push [ENT·WX] to select WX channel mode. · "WX--" and previously selected channel number appears. ï Using the tuning dial q Push [PWR] for 2 sec. to turn power ON, then push [CLR·DEL] to select the frequency mode when memory CH number or WX CH number appears on the function display. w Rotate [DIAL] to set the desired frequency. · To select the 1 MHz tuning step, push , then rotate [DIAL]. Push again to return the normal tuning. w Rotate [DIAL] to select the desired WX channel. e Push [CLR·DEL] to exit the WX channel mode and return to frequency mode. 8 3 BASIC OPERATION I Receiving q Push [PWR] for 2 sec. to turn the power ON. w Push [SQL·WX-ALERT], then rotate [DIAL] counterclockwise to select the squelch level 0. e Rotate [VOL] to adjust the audio level. r Push [SQL·WX-ALERT], then rotate [DIAL] clockwise until the noise is muted. ·" " indicator disappears. I Transmitting CAUTION: Transmitting without an antenna may damage the transceiver. t Set the desired frequency using [DIAL] or keypad. y When a signal is received on the set frequency: ·" " indicator appears. · Squelch opens and audio is emitted from the speaker. NOTE: To prevent interference, listen on the frequency before transmitting. If the frequency is busy, wait until the channel is clear. q Set the desired frequency in COM band using [DIAL] or keypad. · COM band frequency range: 118.00­136.975 MHz When [SQL] setting is too "tight," squelch may not open for weak signals. To receive weaker signals, loosen the squelch. w Push and hold [PTT] to transmit. ·" " indicator appears. e Speak into the microphone at a normal voice level. · DO NOT hold the transceiver too close to your mouth or speak too loudly. This may distort the signal. r Release [PTT] to return to receive. I ANL function The ANL (Automatic Noise Limiter) function reduces noise components such as that caused by engine ignition systems while receiving. · Push [ANL·SCAN] to turn the ANL function ON/OFF. " " appears on the display while the ANL function is ON. 9 BASIC OPERATION 3 I Low battery indicator Low battery indicator appears Low battery indicator when the battery power has decreased to a specified level. The attached battery pack requires recharging. D Deletes the stored recall channel q Push w Push or to select the deleting recall channel. , then push [CLR·DEL] for 2 sec. to delete it. · (e.g.) Deletes "r0" recall channel which is stored 120.450 MHz, and "r1" recall channel stores 123.450 MHz. 3 I Recall function The recall function stores the last 10 frequencies used. The function stores frequencies when the frequency is programmed and transmitted on (except memory, weather and emergency channels). D Replaces the stored recall channel q Push placed. w Push or to select the recall channel to be reor to replace it. , then push D Calling the stored frequencies Push to call the 1st stored frequency. Push to call the 10th stored frequency. Push [CLR·DEL] to exit the recall function. · Replaces the selected channel into the previous channel when is pushed and then is pushed. · Replaces the selected channel into the next channel when is pushed and then is pushed. · (e.g.) To replace "r0" which is stored as 121.375 MHz into "r1", push , then push . Appears recall number. · Recall number rotation : Push : Push NOTE: Deletes in order of old recall channel automatically when stored frequencies exceeds 10 channels. 10 3 BASIC OPERATION I Setting weather alert function An NOAA broadcast station transmits a weather alert tone before any important weather announcements. When the weather alert function is turned ON, the transceiver detects the alert, and sounds a beep tone until the transceiver is operated. The previously selected (used) weather channel is checked any time during standby, or while scanning. · Push , then push [SQL·WX-ALERT] to turns the weather alert function ON (Indicates " " for 1 sec.)/OFF (Indicates " " for 1 sec.). I Side tone function When using an headset (other manufacture's products), the transceiver outputs your transmitted voice to the headset for monitoring. Connect the optional headset with the transceiver when using this function (OPC-499 HEADSET ADAPTER and headset are required). (p. 34) D Setting the side tone level q Push [PTT] to turn the transmit mode ON. w During transmit mode, rotate [DIAL] to adjust the monitoring level. · `ST--0' is OFF and `ST--10' is Max. level. I Accessing 121.5 MHz emergency frequency The IC-A24 and IC-A6 can set to the 121.5 MHz emergency frequency quickly. This function can be activated even when the key lock function is in use. q Push [121.5] for 2 sec. to call the emergency frequency. w Push [CLR·DEL] to exit from the emergency frequency. NEVER operate the transceiver with a headset at high volume levels for long period. A ringing in your ears may occur. If so, reduce the monitor level or discontinue use. I Setting beep tone The beep tone which sounds at the push of a switch can be set, if desired. q Push , then push [8·BEEP] to enter the beep tone setting mode. w Rotate [DIAL] to set the beep level. · `BEP-- 0' is OFF and `BEP-- 9' is Max. level. I Lock function The lock function prevents accidental frequency changes and accidental function activation. q Push , then push [7· ] to turn the lock function ON. ·" " appears. w To turn the function OFF, repeat step q above. ·" " disappears. 11 e Push [CLR·DEL] to exit the beep tone set mode. MEMORY OPERATION I Memory channel selection The transceiver has 200 memory channels for storage of often-used frequencies along with 6-character notes. q Push [MR·MW] to select memory mode. · Memory BANK number and memory CH number appears. 4 3 4 I Transferring memory contents This function transfers a memory channel's contents into the frequency mode. This is useful when searching for signals around a memory channel's frequency. q Push [MR·MW] to select memory mode. w Select the desired memory channel to be transferred using [DIAL] or keypad. e Push , then push [MR·MW] to transfer the memory channel's contents into the frequency mode. · BANK number and memory CH number disappears as frequency mode is automatically selected and the memory contents are transferred. Using [DIAL]: w Push , then push [0·BANK],and rotate [DIAL] to select the desired memory BANK number. Push and push [0·BANK] (or push [CLR·DEL]) to exit the BANK selection mode. e Rotate [DIAL] to select the desired memory CH number. · If no memory CH is programmed in the selected BANK, no memory CH selection is available. Using the Keypad: w Push , and push [0·BANK], then push appropriate digit key ([0·BANK] to [9·TAG]) to select the desired memory BANK number, then push and push [0·BANK] (or push [CLR·DEL]) to exit the BANK-selection mode. e Push 2 appropriate digit key (00 to 19) to select the desired memory CH number. · If no memory CH is programmed in the selected BANK, no memory CH selection is available. NOTE: Comments appear first when programmed, however, the transceiver can be programmed by your dealer to show the operating frequency first. Push [MR·MW] to display the comment in this case. Memory mode Frequency mode 12 4 MEMORY OPERATION I Programming a memory channel The transceiver has 200 (20 CH × 10 BANK) memory channels for storage of often-used frequencies. q Push [CLR·DEL] to select the frequency mode, if necessary. w Select the desired frequency. · Push , then push [ENT·WX] to select a weather channel.* · Set the desired frequency or weather channel* using [DIAL] or keypad. · EXAMPLE: Programming WX-05* into memory BANK 3/ memory channel 9. Push Push or Push Push e Push , then push [MR·MW] to enter the memory writing mode. · "M", Memory BANK and memory channel number are blink. r Rotate [DIAL] to select the desired memory channel number. · Push , then push [0·BANK], and rotate [DIAL] to select the BANK number if desired. · Push [CLR·DEL], [ENT·WX] or push then push [0·BANK] to exit the BANK selection mode. Push (or rotate [DIAL]) Push or t Push [ENT·WX] to program the information into the channel and return to the frequency mode. *Weather channel: U.S.A. version only. Push or (or rotate [DIAL]) Push 13 MEMORY OPERATION 4 I Memory names ï Programming memory names The memory channel can display a 6-character names instead of the programmed frequency. q Rotate [DIAL] to select the desired frequency in the frequency mode. w Push , then push [MR·MW] to program the contents into the selected memory channel. e Rotate [DIAL] to select the desired memory channel to be programmed. · Push , then push [0·BANK], and rotate [DIAL] to select the BANK number if desired. Push [CLR·DEL] to exit the BANK selection mode. Key 1 4 7 ENT Character 1, Q, Z 4, G, H, I 7, P, R, S Program Key 2 5 8 0 Character Key 2, A, B, C 5, J, K, L 8, T, U, V 0, space, 3 6 9 Character 3, D, E, F 6, M, N, O 9, W, X, Y 4 r Push [MR·MW] to enter the memory name programming mode. · "-- -- -- -- -- -- " appears on the display. NOTE: When programming the memory name to the programmed memory channel already, operate as follow. q Operate same as "Transferring memory contents" (see P. 12). w Operate same as w­y processes of "Programming memory names" (see left column). t Push the appropriate digit key several times to select the desired character as listed at right. · To erase a character, overwrite with a space (displayed as _). · To move the cursor forwards or backwards, use [DIAL]. I Clearing the memory contents Unwanted memory channels can be cleared. q Select the memory channel to be cleared. w Push , then push and hold [CLR·DEL] for 1 sec. · "-- -- -- -- -- --" appears momentarily, then the next selectable channel appears. y Push [ENT·WX] to program the name. · Flashing the memory name stops. · When no name is programmed, the display shows the operating frequency. · To clear the entered memory names, push [CLR·DEL] before pushing [ENT·WX]. 14 4 MEMORY OPERATION · EXAMPLE: Programming 125.000 MHz into memory BANK 1/ memory channel 17 with "AIR-23" as a comment. Push Push Push Push Push Push Push Push Push Push NOTE: Push , then push [0·BANK], and then rotate [DIAL] to select the BANK number, if desired. Push [CLR·DEL] to exit the BANK selection mode. 15 SCAN OPERATION I Scan types The U.S.A. version has 3 scan types to suit your needs. The non-U.S.A. versions have 2 scan types. COM BAND SCAN 108.00 MHz 118.00 MHz Scan Jump 5 4 5 I COM band scan q Push [CLR·DEL] to select the frequency mode. w Push [SQL·WX-ALERT], then rotate [DIAL] to set the squelch level to the point where noise is just muted. e Push , then push [ANL·SCAN] to start the scan. · When a signal is received, the scan pauses until it disappears. · To change the scanning direction, rotate [DIAL]. Repeatedly scans 136.975 all frequencies MHz over the entire COM band. r To stop the scan, push [CLR·DEL]. I Memory scan MEMORY SCAN non-TAG channel q Push [MR·MW] to select memory mode. Repeatedly scans selected memory bank's all "TAG" memory channels. Used for checking often-used channels and bypassing usually busy channels such as control-tower frequencies. · Push , then push [0·BANK], and rotate [DIAL] to select the BANK number if desired. Push [CLR·DEL] to exit the BANK selection mode. Mch 2 Mch 1 Mch 19 Mch 4 Mch 6 Mch 7 Mch 10 Mch 8 non-TAG channel w Push [SQL·WX-ALERT], then rotate [DIAL] to set the squelch level to the point where noise is just muted. e Push , then push [ANL·SCAN] to start the scan. · When a signal is received, the scan pauses until it disappears. · To change the scanning direction, rotate [DIAL]. r To stop the scan, push [CLR·DEL]. NOTE: Program 2 or more memory channels to start memory scan. WEATHER CHANNEL SCAN Repeatedly scans all "TAG" weather channels. Weather channels are available for the U.S.A. version only. 16 5 SCAN OPERATION I Weather channel scan (U.S.A. version only) q Push , then push [ENT·WX] to select a weather channel. w Set squelch to the point where noise is just muted. e Push , then push [ANL·SCAN] to start the scan. · When a signal is received, the scan pauses until it disappears. · To change the scanning direction, rotate [DIAL]. I "TAG" channel setting Memory and weather channels* can be specified to be skipped for the memory and weather channel* scans respectively. The "TAG" channel function is only available during scan operation. Push then r To stop the scan, push [CLR·DEL]. Appears the "TAG" indicator. Memory channel 15 is scanned during memory scan. Memory channel 15 is skipped during scan. q Push [MR·MW] to select memory mode; or, push , then push [ENT·WX] to select a weather channel.* w Select the desired memory channel to be a "TAG" channel. · Push , then push [0·BANK], and rotate [DIAL] to select the BANK number if desired. Push [CLR·DEL] to exit the BANK selection mode. e Push , then push [9·TAG] to set a "TAG." · "TAG" appears. · Non-"TAG" channels are skipped during scan. r To cancel the "TAG" setting, repeat above steps. *Weather channel: U.S.A. version only. 17 VOR NAVIGATION (IC-A24 ONLY) I VOR indicators NAV BAND (108.00 117.975 MHz) COM BAND (118.00 136.975 MHz) DVOR MODE 6 5 6 Course indicator To-from flag indicator Push [F] then [1 DVOR]. CDI MODE General VOR equipment Course indicator To-from flag indicator Two-degree deviation marks Course deviation needle 34 214 FROM Push [F] then [4 CDI]. Function display of the IC-A24 Course indicator To-from flag indicator Course deviation needles Overflow indicator 18 6 VOR NAVIGATION (IC-A24 ONLY) D `TO' or `FROM' flag selection The to-from flag indicators indicate whether the VOR navigation information is based on a course leading to the VOR station or leading away from the VOR station. Push , then push [3·FROM] or [2·TO] to change the flag from `TO' to `FROM' or vice versa, respectively. I VOR functions D To select the CDI mode To show the deviation between your flying course and the desired course, push , then push [4·CDI] to select the CDI mode. Operating frequency can not be changed. Each course deviation arrow indicates a two-degree deviation. Course indicator is fixed, but it can be changed with the tuning [DIAL] or keypad. D To select the DVOR mode When entering the NAV band, 108.000­117.975 MHz, the IC-A24 selects the DVOR mode automatically. To show your aircraft's direction to (or from) the VOR station, push , then push [1·DVOR] to select the DVOR mode. Operating frequency can not be changed. Course deviation needle does not appear. Course indicator shows your direction to (or from) the VOR station. NOTE: · When using the `TO' flag and passing through the VOR station, the `TO' flag changes to the `FROM' flag automatically. · When turning power ON, the `FROM' flag is selected automatically. D Selecting the next VOR station when using CDI mode (when using the course deviation needle) q Push , then push [1·DVOR] to select the DVOR mode. w Push the keypad or rotate [DIAL] to set the next VOR station's frequency. e Push , then push [4·CDI] to select the CDI mode. · Select `TO' or `FROM' flag, if desired. 19 VOR NAVIGATION (IC-A24 ONLY) 6 I Flying to a VOR station The IC-A24 shows the deviation from a VOR station. q Select a VOR station on your aeronautical chart and push the keypad or rotate [DIAL] to set the frequency of the station. · The course indicator indicates where you are located on a radial from the VOR station. · The course indicator shows `- -' when either aircraft is too far away from the VOR station or the frequency is not set correctly at the VOR station. r The course deviation needle appears when your aircraft is off course from the VOR station. · `' or `' appears to indicate your aircraft is off course to the right or left, respectively. Correct your course until `' or `' disappears. Each arrow represents a two-degree deviation. t Push , then push [1·DVOR] to exit the CDI mode. VOR INDICATOR NOTE `loc' appears on the function display as shown below when a localizer signal is received. However, the function display does not indicate additional information about the localizer signal. 6 w Select the `TO' flag when flying to the VOR station, or select the `FROM' flag when flying away from the VOR station. · Push , then push [2·TO] to select `TO'. · Push , then push [3·FROM] to select `FROM'. e Push , then push [4·CDI] to select the CDI (Course Deviation Indicator) mode. · The course indicator shows `OF' when the desired VOR signal cannot be received. NOTE: When the CDI mode is selected, the operating frequency cannot be changed. To set the operating frequency, select the DVOR mode in advance. NOTE: For U.S.A. version only IC-A24's VOR and CDI Navigation features are supplemental aids to navigation only, and are not intended to be a substitute for accurate (primary) VOR/CDI or landing service equipment. 20 6 VOR NAVIGATION (IC-A24 ONLY) 0 THE AIRCRAFT IS ON COURSE 123.65 VORTAC SEATTLE 116.8 Ch 115 SEA 300 290 280 270 260 250 240 230 330 340 350 310 320 10 20 30 40 50 60 N Magnetic north Des Airc ir ou ed c rse 40 220 210 200 190 180 170 VOR station 70 80 90 100 110 r ea aft h ding 130 160 150 140 120 0 THE AIRCRAFT IS OFF COURSE 123.65 VORTAC SEATTLE 116.8 Ch 115 SEA 300 290 280 270 260 250 240 230 220 210 200 190 180 330 340 350 310 320 10 20 30 40 50 60 N Magnetic north 46 ding ft hea Aircra ourse) fc (6 of ourse nc Flow VOR station 70 80 90 100 110 NOTE: The course deviation indicator appears when the aircraft is off course. In this example, the aircraft is 6 degrees off course to the left. The pilot must turn more than 6 degrees right to get back on course. 21 ould ft sh ircra g 40 A din hea be 170 130 160 150 140 120 VOR NAVIGATION (IC-A24 ONLY) 6 I Entering a desired course The IC-A24 shows not only the deviation from the VOR station but the deviation from the desired course. q Push the keypad or rotate [DIAL] to set the frequency for the desired VOR station. · Push , then push [2·TO] or [3·FROM] to change the to-from flag. I Crosschecking position q Select 2 VOR stations on your aeronautical chart. w Push the keypad or rotate [DIAL] to set the frequency of one of the VOR station in the DVOR mode. · The course indicator shows course deviation from the VOR radial. Note the radial you are on. e Push the keypad or rotate [DIAL] to set the frequency of the other VOR station in DVOR mode. · Note the radial from the station you are on. w Push , then push [4·CDI] to select CDI mode. e Set the desired course to the VOR station using the tuning dial or keypad. · `' or `' appears on the function display when your aircraft is off the desired course. · When your heading is correct, the ABSS function (see right column for detail) may be useful instead of course input. 6 r Extend the radials from each VOR station on the chart. Your aircraft is located at the point where the lines intersect. r The course deviation needle points to the right when your aircraft is off course to the left. · To get back on course, fly right more than the number of degrees indicated by the CDI arrows. · If the overflow indicator appears on the right side, select a heading plus 10 degrees to the desired course; if the overflow indicator appears on the left side, select a heading minus 10 degrees. ABSS FUNCTION In the CDI mode, the Auto Bearing Set System (ABSS) adds or subtracts the number of degrees indicated by the CDI arrows from the Omni Bearing Selector (OBS). To use ABSS, push , then push [2·TO] while using the `TO' flag; or, push , then push [3·FROM] while using the `FROM' flag. qw er q Overflow indicator (left) w Course deviation needles (left) e Course deviation needles (right) r Overflow indicator (right) 22 6 VOR NAVIGATION (IC-A24 ONLY) EXAMPLE: Entering the desired course bearing 65° to a VOR station. CROSSCHECKING POSITION VORTAC OLYMPIA 113.4 Ch 81 OLM 0 300 290 280 270 260 250 240 230 220 210 200 190 180 170 130 160 150 140 330 340 350 310 320 10 20 30 40 50 60 300 290 280 270 260 250 240 230 220 210 200 190 180 170 130 160 150 140 330 340 350 310 320 10 20 30 40 50 60 0 123.65 VORTAC SEATTLE 116.8 Ch 115 SEA N Magnetic north VOR station 70 80 90 100 110 120 VOR station 70 80 90 100 110 120 23 VOR NAVIGATION (IC-A24 ONLY) 6 I Duplex operation (U.S.A. version only) The duplex function allows you to call a flight service station while receiving a VOR station. The duplex function requires frequency programming for the flight service station in advance. D Operating the duplex function q Set the desired frequency in NAV band. · NAV band frequency range: 108.00­117.975 MHz w Push ON. , then push [6·DUP] to turn the duplex function · "DUP" appears on the function display. D Programming a duplex frequency q Push [CLR·DEL] to select the frequency mode. w Set a NAV band frequency using the tuning dial or keypad. · NAV band frequency range: 108.00­117.975 MHz e Push and hold [PTT] to transmit at the pre-programmed transmit frequency. r Release [PTT] to return to receive. t Push , then push [6·DUP] to cancel the function. · "DUP" disappears on the function display. 6 e Push , then push [5·DUP-W]. · "DUP" flashes and transmit frequency appears. r Set the frequency of the flight service station using the tuning dial or keypad. When using the tuning dial, push [ENT·WX] after setting a frequency. · The displayed frequency returns to the NAV band frequency. NOTE: A duplex frequency can be programmed into each memory channel independently. Set a duplex frequency before programming the memory channel, if desired. The duplex ON/OFF setting can also be programmed into a memory channel. EXAMPLE: Programming 123.65 MHz as the transmit frequency in the duplex function. 24 7 BATTERY PACKS I Battery cautions CAUTION! NEVER insert battery pack/transceiver (with the battery pack attached) with wet or soiled into the charger. This may result in corrosion of the charger terminals or damage to the charger. The charger is not waterproof and water can easily get into it. I Battery charging Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. CAUTION: To avoid damage to the transceiver, turn the power OFF while charging. · Recommended temperature range for charging: +10°C to +40°C (+50°F to +104°F) - The Li-Ion battery (optional) is functioning within ­20°C to +60°C (­4°F to +140°F). · Use the supplied AC adapter on regular charging. NEVER use another manufacture's adapters. · Use the specified chargers (BC-119N, BC-121N and BC-144N). NEVER use another manufacture's charger. NEVER connect DC power to the transceiver when installing Alkaline batteries. Such a connection will damage the transceiver. NEVER incinerate used battery packs. Internal battery gas may cause an explosion. NEVER immerse battery pack in water. If the battery pack becomes wet, be sure to wipe it dry immediately (particularly the battery terminals BEFORE attaching it to the transceiver. NEVER short the terminals of the battery pack. Also, current may flow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carrying in handbags, etc. If your battery pack seem to have no capacity even after being charged, completely discharge them by leaving the power ON overnight. Then, fully charge the battery pack again. If the batteries still do not retain a charge (or very little), new battery pack must be purchased. Turn the transceiver power OFF when charging the battery pack. Otherwise, the battery pack may not fully charge or charge properly. D Recycling information (U.S.A. only) The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Call 1-800822-8837 for battery recycling options in your area or contact your dealer. 25 BATTERY PACKS D Regular charging q Attach the battery pack to the transceiver. w Be sure to turn the transceiver power OFF. e Connect the Wall charger or optional cable (CP-20) as shown below. r Charging the battery pack approx. 8 hours, depending on the remaining power condition. DO NOT charge BP-210N more than 12 hours. Otherwise, BP-210N will be damaged. BP-210N must be charged for 8­12 hours only.