INSTRUCTION MANUAL COMMUNICATIONS RECEIVER FOR COMPUTER iPCR1000 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ ALL INSTRUCTIONS and on-line help carefully and completely before using the receiver. FEATURES · USER-SELECTABLE INTERFACE Users can choose from 3 different operating screens depending on their ability level and preference. · WIDE FREQUENCY RANGE, MULTI-MODE RECEIVE The IC-PCR1000 has a wide frequency coverage from 0.5 MHz to 1300 MHz* with all mode receive capability. * Some frequency ranges are restricted depending on version. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-PCR1000 COMMUNICATIONS RECEIVER FOR COMPUTER. USE antenna(s), such as a well-matched 50 antenna and feedline. For radio communications, the antenna is of critical importance, along with sensitivity. · IF SHIFT The IF shift function is effective in SSB mode for reducing interference from nearby signals. It does so by electronically shifting the passband of the IF filter. · REAL-TIME BANDSCOPE FUNCTION The real-time bandscope function makes it easy to find busy frequencies and also easy to observe receive frequency band conditions. The maximum band width is ±200 kHz. · NOISE BLANKER · VSC (Voice Scan Control) FUNCTION · S-METER SQUELCH · HIGH PERFORMANCE PLL CIRCUIT · A VARIETY OF TUNING STEPS · A VARIETY OF SCANS · DIGITAL AFC CIRCUIT Versions of the IC-PCR1000 which display "CE" on the serial number seal, comply with the essential requirements of the 89/336/EEC directive for Electromagnetic Compatibility. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. WORD Icom, Icom Inc. and are registered trademarks of Icom Incorporated (Japan) in the United States, United Kingdom, Germany, France, Spain, Russia and/or other countries. i PRECAUTION RWARNING! NEVER connect the receiver to an AC outlet. This may pose a fire hazard or result in an electric shock. For U.S.A. only (FCC information) CAUTION: NEVER connect other than the specified AC adapter to the receiver. This connection will ruin the receiver. NEVER connect the receiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruin the receiver. Changes or modifications to this receiver, not expressly approved by Icom Inc., could void your authority to operate this receiver under FCC regulations. Class B digital device users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NEVER allow children to touch the receiver. NEVER expose the receiver to rain, snow or any liquids. DO NOT use or place the receiver in areas with temperatures below 0°C (+32°F) or above +50°C (+122°F) or, in areas subject to direct sunlight. AVOID placing the receiver in excessively dusty environments. AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they damage the receiver surfaces. Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the U.S.A and other countries. Screen shots produced with permission from Microsoft Corporation. All other products or brands are registered trademarks or trademarks of their respective holders. For Canada only Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. ii SYSTEM REQUIREMENTS · An RS-232C serial port (38400 bps or faster) · Microsoft® Windows® 98/98SE/Me/2000/XP · At least 10 MB of hard disk space · 640 480 pixel display (800 600 pixel display recommended) TABLE OF CONTENTS IMPORTANT .....................................................................i EXPLICIT DEFINITIONS ......................................................i FEATURES ........................................................................i PRECAUTION ..................................................................ii SYSTEM REQUIREMENTS ................................................iii TABLE OF CONTENTS ......................................................iii 1 INSTALLATION ............................................................1­7 I Hardware installation ......................................................1 I Antenna installation ......................................................2 I Grounding ..................................................................2 I AF output level selection ................................................3 I TNC connection ............................................................4 I Software installation ......................................................5 I Uninstallation ...............................................................6 I Starting the IC-PCR1000 ................................................7 I Serial port setting .........................................................7 2 PANEL DESCRIPTION ................................................8­12 I Component screen.........................................................8 I Radio screen...............................................................12 I Communications receiver screen ....................................12 3 SPECIFICATIONS......................................................13­14 4 SUPPLIED ACCESORIES AND OPTIONS ........................15 I Supplied accesories......................................................15 I Options .....................................................................15 iii INSTALLATION I Hardware installation Refer to the diagram below for connections. Remove the protective sheet and attach to a specified place. USB serial adapter cable 1 to an USB port Personal computer to an RS-232C port to an AC adapter Ground * When using the USB serial adapter cable, USB serial port can be used. It is necessary to USB driver installation. The driver is supplied with the USB serial adapter cable. COMM UNICA iC- pc TIONS RE r100 CEIVE R 0 1 1 INSTALLATION I Antenna installation Antennas play a very important role in receiver operation. Connecting a poor quality antenna to the IC-PCR1000 will result in less than optimum performance. Select antenna(s), such as a well-matched 50 antenna and feedline. 1.5:1 of Voltage Standing Wave Ratio (VSWR) is recommended for a desired band. Of course, the antenna line should be a coaxial cable. I Grounding R WARNING: NEVER use a gas pipe or electrical conduit pipe for grounding. To prevent accidents involving electricity and interference from computers, ground the receiver through the GROUND terminal on the rear panel. For best results, connect a heavy gauge cable to a water pipe or long, earth-sunk copper rod. Make the distance between the [GND] terminal and ground as short as possible. CAUTION: Protect your receiver from lightning by using a lightning arrestor. NOTE: The supplied antenna is a simple plain antenna which may not obtain indicated specifications. To obtain maximum performance from the IC-PCR1000, you must purchase an external wide band antenna such as an optional Icom AH-7000 (25­1300 MHz), etc. Contact your nearest Icom Dealer or Service Center for regarding optimum antenna locations. The antenna connector type is BNC, so an adapter may be necessary to connect an optional antenna. 2 COMM ICATIO iC- pc NS RE r100 CEIVE R 0 UN INSTALLATION 1 I AF output level selection The received audio can be input into your computer via the sound card. Before inputting the received audio into the [LINE IN] connector (connector name depends on your sound card), the output level of the [EXT-SP] must be set properly. Perform as follows: q Remove the 8 screws from the cover as shown below. Open the cover. w Select the output level as shown below. - "SPEAKER" for internal speaker. - "PHONES" for PC sound card or headphones. e Replace the 8 screws and cover. r Connect an appropriate cable between IC-PCR1000 and PC. - Plug for [EXT-SP] is supplied with the receiver. IC-PCR1000 COMMUN ICAT iC- pc IONS RECEIVE r100 R 0 SPEAKER PHONES to [LINE IN] (depends on your sound card) [EXT-SP] 3 1 INSTALLATION I TNC connection The IC-PCR1000 can receive 9600 bps packet communication (AFSK). Connect the TNC (Terminal Node Controller) as follows. to [PACKET] 4 COMM UNICAT IONS iC- pcr 1000RECEIVER IC-PCR1000 TNC Personal computer INSTALLATION 1 I Software installation When installing into a Windows XP or Windows 2000 environment, log on as the administrator. q Quit all applications when windows is running. w Insert the CD into the CD drive. e Select `Run' from the [Start] menu. r Type the setup program name with full path name, then push the [Enter] key. (D:\SETUP.exe [Enter]) t Click [OK]. * The following screens show Windows XP. · The "InstallShild® Wizard" starts preparing the installation. y After the preparation, the following dialog is displayed. Click [Next>]. Installing starts. Click Click 5 1 INSTALLATION I Uninstallation This section describes [IC-PCR1000] uninstallation. D Windows XP [Procedure] q Click and select [Control Panel]. w Click [Add or Remove Programs] and select [ICOM ICPCR1000] and click . e [IC-PCR1000] Uninstall Wizard starts automatically. r Click and follow the prompts. u After the installation is completed, click [Finish]. D Windows 98/98SE/Me/2000 [Procedure] q Click and select [Control Panel] from the [Settings] menu. w Double-click [Add or Remove Programs] and select [ICOM IC-PCR1000] and click . e Follow the prompts. Click i Eject the CD. 6 INSTALLATION 1 I Starting the IC-PCR1000 D Windows XP q Before launching the program, make sure the IC-PCR1000 interface unit power is turned ON (the LED lights when power is on). w Click and select [PCR1000] from the [All Programs] menu. e Select the [IC-PCR1000] program. D On-line help information See the on-line help for software usage. q Click the [Contents] in the [Help] menu to bring up the online help. w Click the desired information you want to know. D Software update information Software update information will be available at the Icom America home page: http://www.icomamerica.com/ D Windows 98/98SE/Me/2000 q Before launching the program, make sure the IC-PCR1000 interface unit power is turned ON (the LED lights when power is on). w Click and select [PCR1000] from the [Programs] menu. e Select the [PCR1000] program. I Serial port setting Select the RS-232C serial port correctly if the title bar displays "COM port trouble?". q Before launching the program make sure the IC-PCR1000 interface unit power is turned on (the LED lights when power is on). w Launch the IC-PCR1000 software. e Click the [POWER] button in the tool bar to temporarily pause the program. r Click the [PORT] button to bring up the [RS-232C PORT Number] dialog box. t Click the desired port COM number to choose it. y Click the [OK] button. 7 2 PANEL DESCRIPTION r FREQ (frequency) indication Indicates the receive frequency and data as it is being input such as memory channel numbers, etc. o i t TS (tuning step) indicator This is the frequency increment used when selecting a frequency using the [Main dial] and when searching for signals using a scan function. y Numeral buttons ([0] to [9]) Used to input a receive frequency or memory channel directly. u Mch (memory channel) button Used to set the numeral buttons for memory channel input. !2 !1 !0 i Tuning step buttons Used to change the tuning step. o Main dial Used to s ...