5010cs ,6010cs ,6810cs instructi o reference series ns INSTALLATION WARNINGS AND TIPS THANK YOU for purchasing Infinity's Reference Series automotive loudspeaker components. We've organized this manual to make your installation as simple and trouble-free as possible. Please read it thoroughly before proceeding. Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. IMPORTANT: Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Reference Series speakers in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself; instead, ask your authorized Infinity car audio dealer about professional installation options. WARNING: Playing loud music in an automobile can permanently damage your hearing, as well as hinder your ability to hear traffic. The maximum volume levels achievable with Infinity speakers, combined with high power amplification, may exceed safe levels for extended listening. We recommend using low volume levels when driving. Infinity accepts no liability for hearing loss, bodily injury, or property damage as a result of use or misuse of this product. · Always wear protective eyewear when using any tools. · Turn off all audio systems and other electrical devices before you start. Disconnect the (­) negative lead from your vehicle's battery. · Keep speakers in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. Never use force to install any speaker. · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines, and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location! · Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box, or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the 5010cs woofer with the grille. Figure 3. Mounting the 6010cs in 165mm speaker locations. FOAM GASKET Figure 2. Mounting the 6010cs woofer with the grille. MOUNTING RING INTERMOUNT III (PATENT NO. 6,505,705) The 6010cs is packaged with two different speaker adaptor rings. These are used to install the 6-1/2" speakers in various vehicles. The metal ring can be mounted in many European vehicles, while the plastic ring can be mounted in many vehicles using 6-3/4" speaker locations or three-point mounting frames. Figure 4. Mounting the 6010cs woofer in standard speaker locations. Note: The 6810cs is designed to replace 5" x 7" and 6" x 8" speakers installed behind existing vehicle grilles, and does not include grilles. FOAM GASKET INSTALLATION FLUSH-MOUNT Figure 5A. Mounting the tweeter using the I-MountTM (patent no. 5,859,917) flush-mounting kit. 3 TWEETER ANGLE Figure 6. 3 ROTATE ENTIRE ASSEMBLY TO AIM ANGLED TWEETER TOWARD LISTENER. Figure 7A. Behind grille panel. Figure 7C. Mounted to grille panel. 1 SLIDE SCREW UP OR DOWN TO ADJUST TWEETER ANGLE. 1 2 Note: Aim the tweeter at the listening position by sliding the stud in the groove on the back of the tweeter cup and rotating the entire assembly in the mounting surface. Lock the tweeter in place, using the small retaining screw. SURFACE-MOUNT Figure 5B. Mounting the tweeter using the (--) SMALL LUG BLACK I-Mount surface-mounting kit. 1 ATTACH BASE WITH SCREWS, THEN: 2 TIGHTEN SCREW TO LOCK ANGLE SETTINGS. Figure 7B. Mounted to surface behind grille panel. Figure 7D. In-dash location (may require gluing). SECURELY TIGHTEN THE LARGE HAND NUT. BLACK (--) 4 BLACK (--) RED (+) 2 3 Figures 7A through 7D. The StarfishTM tweeter RED (+) mount is intended to be used when the tweeter will be installed behind a factory grille (e.g., replacing the factory tweeter behind a door RED panel). The Starfish will allow you to mount the (+) LARGE LUG component tweeter directly to the panel itself or to the area behind the panel. The six mounting tabs can be removed easily to create a number of custom configurations. The tabs of the Starfish can be screwed or glued to the mounting surface for secure installation. Note: Check screw clearance before installing. Use glue if clearance is an issue. reference series Note: Not all possible mounting configurations are shown. CONNECTIONS Connect the speakers to the crossover and the crossover to the amplifier, observing proper polarity. Figure 8A. p/s 050 2ohm 5.4uF SPECIFICATIONS 5010cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2.83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 5-1/4" 2-Way Component System 4 Ohms 75W RMS, 225W Peak 67Hz ­ 21kHz 91dB 3.5kHz Woofer: 2-1/4" (58mm) Tweeter: 5/8" (16mm) Woofer: 4-11/16" (120mm) Tweeter: 1-3/4" (45mm) 6810cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2.83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 6" x 8"/5" x 7" 2-Way Component System 4 Ohms 90W RMS, 270W Peak 49Hz ­ 21kHz 92dB 3.5kHz Woofer: 2-7/16" (62mm) Tweeter: 5/8" (16mm) Woofer: 5" x 7-1/4" (127mm x 185mm) Tweeter: 1-3/4" (45mm) 6.8uF 2ohm 0.22mH 0.15mH - IN + - WF + - TW + -3dB _ + TO AMPLIFIER + _+ _ TO TWEETER SPEAKER OUTPUTS TO WOOFER Note: To reduce tweeter output level, connect the positive (+) tweeter wire to the ­3dB terminal. Figure 8B. 6010cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2.83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 6-1/2" 2-Way Component System 4 Ohms 90W RMS, 270W Peak 53Hz ­ 21kHz 92dB 3.5kHz Woofer: 2-1/16" (53mm) Tweeter: 5/8" (16mm) Woofer: 5" (127mm) Tweeter: 1-3/4" (45mm) A valid serial number is required for warranty coverage. Features, specifications and appearance are subject to change without notice. Declaration of Conformity We, Harman Consumer Group International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 BIG LUG IS POSITIVE (+) SMALL LUG IS NEGATIVE (­) Infinity Systems · 250 Crossways Park Drive, Woodbury, NY 11797 USA 516.674.4463 · FAX 516.682.3523 · www.infinitysystems.com © 2005 Harman International Industries, Incorporated · Part No. REFCSOM1/05 ¤ Klaus Lebherz Harman Consumer Group International Chateau-du-Loir, France 1/05 ...