Indoor/Outdoor 1A2, 3A2, 3S, 3T, 8A2 1 Congratulations on your purchase of Jamo Indoor/Outdoor speakers. Congratulations on your purchase of Jamo Indoor/Outdoor speakers Package content. Speaker (2) Port plug "i" (4) Assembled bracket (2) Thumb screw "j" (4) Package content Screw (2) "g" (8) Port plug "i" (4) Covers "k" (4) Speaker plug Allen wrench (1) Assembled bracket (2) Thumb screw "j" (4) Manual (1) Allen wrench (1 Manual (1) Screw plug Covers "k" (4) Bracket. "g" (8) The brackets comes pre-assembled. If disassembling the bracket for pai Bracket The re-assemble it as follow: Place the curved bracket (a) between the w ing,brackets comes pre-assembled. If disassemblingthebracket for paint-ing, re-assemble it as follow: Place the curved bracket (a) between the wall bracket (b) and wall bracket cover bracket (b)fig. 1. Insert two 1" allen bolts (d) through as shown in fig. 1. Insert two 1" al (c) as shown in and wall bracket cover (c) wall bracket into wall bracket cover and tighten through wall bracket into wall bracket cover and wall bolts (d) with the supplied allen wrench. Insert two ½" allen bolts (e) into each side of tighten with t bracket and supplied tighten towards curvedInsert two ½" allen bolts (e) into each side of w allen wrench. bracket. bracket and tighten towards curved bracket. Fig. 1 a e f d d b e c Fig. 1 Mountingbracket Mounting of of bracket. The bracket can be for horizontal orfor horizontal the vertical placement of t Thebracket can be mounted included) appropriate for placement of or speaker.mountedthe mounted vertical the surface the bracket is Mount to bracket with four screws (not speaker. Mountor other). Take into account four screws speaker included) on (wood, brick, concrete the bracket with the weight of the (not (specifications appropriate back). A hole (f in the middle of the mounted to (wood, brick, concrete or the surface) the bracket isbracket allows for running the speaker wire through the other). Ta bracket if so desired. Cover the screws with four screw plugs (g) fig. 2. into account the weight of the speaker (speci cations on back). A hole (f) the middle of the bracket allows for running the speaker wire through t Mounting of port plugs If the front of the desired. Cover the screws with bass reflex ports (under (g) bracket if so speaker is exposed to rain directly entering the four screw plugsthe fig. 2. grill), the ports should be closed to avoid filling the speaker with water. High moisture is not a problem. Remove the grill (h) from the speaker and insert two port plugs (i) into the bass ports. Re-install the of port plugs. Mountinggrill. The speaker will reproduce less bass with the ports closed. 2 If the front of the speaker is exposed to rain directly entering the bass re ports (under the grill), the ports should be closed to avoid lling t speaker with water. High moisture is not a problem. Remove the grill from the speaker and insert two port plugs (i) into the bass ports. Re-ins the grill. The speaker will reproduce less bass with the ports closed. Connecting speaker wires Loosen speaker terminals by turning counter clockwise. Strip ½"/12 mm in-sulation off each wire. Twist strands on each wire to form "solid" wire. Insert one wire into each terminal and tighten terminal by turning clockwise. Make sure positive (+) is to red terminal and negative (-) to black terminal for correct phasing. Adjustment of I/O 3T This model is for 70V or 100V line installation. This is mainly used in com-mercial installations with many speakers and requires an amplifier with matching transformer outputs. A switch located next to the terminals al-lows for adjustments of the level of the speaker in 10W, 5W, 2.5W and 1.25W settings. Adjust the switch to the desired level on each speaker. Mounting of speaker Place the speaker inside the curved bracket as shown in fig. 2 and insert thumb screws (j) through each end of the curved bracket into the speaker. Adjust the speaker to the desired angle and tighten the thumb screws. In-stall the covers (k) over the thumb screws. The curved bracket can be ad-justed in the wall bracket by loosening the two ½" allen bolts (e) and re-tighten them after adjustment. Fig. 2 k j l i i h j k g g Painting The speaker and bracket can be painted. Spray painting is recommended. Paint all parts before assembling. Remove the grill from the speaker before painting and cover the front baffle (l) of the speaker. Apply many thin coats instead of a few thick coats to avoid the paint running or clogging the grill holes. Re-install grill after painting. 3 Specifications Model System Woofer (in/mm) Tweeter (in/mm) Power (W long/short term) Sensitivity (dB/2.83V/1m) Frequency range (Hz) Impedance (Ohm) Weight (lb/kg) Dimensions HxWxD (in/mm) I/O 1A2 2 way ported 4½/114 ½/13 Dome 20/40 86 77-20.000 6 5.1/2.3 9.1x6.3x6.6 232x160x168 I/O 3A2 2 way ported 5¼/133 1/25 Dome 40/80 88 64-20.000 8 6.9/3.2 11.4x7.9x8.2 290x200x209 I/O 3S 2 way ported 5¼/133 2x1/25 Dome 40/80 88 55-20 000 8+8 8.3/3.8 11.4x7.9x8.2 290x200x209 I/O 3T 2 way ported 5¼/133 1/25 Dome 40/80 88 64-20.000 70/100V line 7.3/3.3 11.4x7.9x8.2 290x200x209 I/O 8A2 2 way ported 8/203 1/25 Dome 80/125 88 50-20.000 8 10.1/4.6 13.5x9.3x9.8 344x237x248 The scope of the warranty Service. In case of warranty enquiries, please contact your dealer/installer. In case of request for service under warranty, please enclose your original receipt and make sure that the serial number on the product is readable. Important: Never send the product to be repaired without the prior agreement of your dealer. The product must always be packed properly. If the product is NOT UNDER WARRANTY, all costs including without limit costs of repair and freight must be paid for by the customer. Terms of Warranty 1. Nothing in this warranty shall limit your statutory rights. 2. The warranty is only valid on presentation of the original sales receipt or other valid proof of purchase, and provided that the serial number on the product is fully legible. 3. Warranty repairs must be carried out by an authorised Jamo dealer, or an authorised service centre. No payment will be made for repairs performed by unauthorised persons. This warranty does not extend to products which have been repaired or otherwise altered by unauthorised persons, and any damage to the product caused by work by unauthorised persons is not covered by this warranty. 4. This product will not be considered defective, either in materials or in manufacture, to the extent that faults are caused by adaptation to national, local, technical or safety related requirements in countries other than the specific country where the product was purchased. 5. Jamo shall at its option during the relevant warranty period either repair or replace defective components. If the component repair or replacement cannot be performed, the product will be replaced. 6. In no circumstances shall Jamo be liable in contract, tort (including negligence) or breach of statutory duty or otherwise for loss of profits, loss of revenue, loss of data, loss of business or loss of anticipated savings or for any consequential loss whatever. 7. The warranty does not cover the following: a) Periodic inspection, maintenance and repair or replacement of parts resulting from normal wear and tear. b) Costs connected to delivery to the dealer, disassembly or re-installation of the product. c) Misuse, including use for purposes other than was intended, or faulty installation. d) Damage caused by lightning, water, fire, natural catastrophes, war, insurrection, incorrect line voltage, insufficient ventilation, transport or other causes outside of the control of Jamo. 8. This warranty applies to every legal owner of the product during the warranty period. 4 Enceintes à usage intérieur et extérieur 1A2, 3A2, 3S, 3T, 8A2 Congratulations on your purchase of Jamo Indoor/Outdoor speakers. Toutes nos félicitations pour avoir acheté ces enceintes Jamo Package content. pour usage intérieur et extérieur Speaker (2) Port plug "i" (4) Assembled bracket (2) Thumb screw "j" (4) Contenu de l'emballage Screw plug "g" (8) Covers Clé hexagonale (1) "k" (4) Enceintes (2) Porte-prises "i" (4) Support assemblé (2) Vis à serrage "j" (4) Manuel (1) Allen wrench (1 Manual (1) Cache vis "g" Cache "k" (4) Bracket. (8) The brackets comes pre-assembled. If disassembling the bracket for pai Support Le support est livré pré-assemblé. Si le support est démonté pour être bracket (a) between the w ing, re-assemble it as follow: Place the curved peint, il faut le réassembler en suivant cette procédure : placez bracket (b)(c) comme montré dans le support courbé (a) entre les supportsfig. 1.hexago- two 1" al and wall bracket cover (c) as shownàin muraux (b) et le Insert cache support la figure. 1. Insérez deux boulons tête creuse bolts (d) through wall bracket dans le wall du support mural et serrez avec la nale de 1 pouce (d) à travers le support mural, into cache bracket cover and tighten with t clé hexagonale. Insérez deux boulons à tête two ½" allen bolts (e) chaque côté supplied allen wrench. Insertcreuse hexagonale de ½ pouce (e) deinto each side of w du support mural, et serrez pour fixer le support courbé. bracket and tighten towards curved bracket. Fig. 1 a e f d d b e c Fig. 1 into account the weight of the speaker (speci cations on back). A hole (f) Fixation du porte-prises the middle of the bracket allows for running the speaker wire through t Si l'avant bracketde l'enceinte est exposé directement à la pluiewith four évents deplugs (g) fig. 2. if so desired. Cover the screws menant aux screw résonance (sous la grille), les ports doivent être bouchés pour éviter l'inondation des haut-parleurs. Une grande humidité est sans effet. Retirez la grille (h) de l'enceinte et insérez deux porte-prises (i) Fixation du support Le support peut être fixé de manière à y placer une enceinte à l'horizontale ou à la verticale. Mounting of bracket. appropriées à la surface à laquelle le support est fixé (bois, Utilisez quatre vis (non incluses) The bracket autre). Ilbe mounteddufor horizontal(spécifications au dos). Le brique, béton ou can faut tenir compte poids de l'enceinte or vertical placement of t trou (f ) au milieu du speaker. Mount the bracket with four screws (not included) appropriate support permet l'enceinte si the surfaceà de faire passer les fils devis (g) fig. 2. c'est(wood, brick, concrete or other). Ta the bracket is mounted to nécessaire. Couvrez les vis l'aide de quatre caches 6 les évents des of port plugs. Mounting graves. Remettez la grille. L'enceinte émettra moins de graves si les ports sont Iffermés.front of the speaker is exposed to rain directly entering the bass re the ports (under the grill), the ports should be closed to avoid lling t speaker with water. High moisture is not a problem. Remove the grill from the speaker and insert two port plugs (i) into the bass ports. Re-ins the grill. The speaker will reproduce less bass with the ports closed. Raccordement des fils de l'enceinte Tournez les borniers pour haut-parleurs dans le sens anti-horaire pour les desserrer. Dénudez chaque fil sur une longueur de ½"/12 mm. Tressez les brins des de chaque fil pour les renforcer. Insérez un fil dans chaque bornier et serrez ce dernier en le tournant dans le sens horaire. Assurez-vous que le positif (+) va dans le bornier rouge et le négatif (-) dans le bornier noir pour une mise en phase correcte. Réglage de l'I/O 3T Ce modèle est destiné à une installation 70 ou 100 V. Cela concerne principalement les installations commerciales avec plusieurs enceintes et qui nécessite un amplificateur avec des sorties correspondantes. Un bouton situé à côté des borniers permet de régler le niveau de puissance de l'enceinte de 10, 5, 2,5 ou 1,25 W. Rglez le niveau de puissance de chaque enceinte. Fixation de l'enceinte Placez l'enceinte à l'intérieur du support courbé comme illustré dans la figure. 2 et insérez des vis à serrage à main (j) à travers chaque extrémité du support courbé dans l'enceinte. Réglez l'angle d'inclinaison de l'enceinte et serrez les vis. Installez le cache (k) au dessus des vis à serrage à main. Le support courbé peut être ajusté dans le support mural en desserrant deux boulons à tête creuse hexagonale de ½" (e) puis en les resserrant après le réglage. Fig. 2 k j l i i h j k g g Peinture Vous pouvez peindre l'enceinte et les vis. La peinture par pulvérisation est recommandée. Il vaut mieux peindre tous les composants avant l'assemblage. Retirez la grille de l'enceinte avant de peindre en couvrant le baffle frontal (l) de l'enceinte. Appliquez plusieurs couches minces au lieu de quelques couches épaisses pour éviter que la peinture ne coule et bouche les orifices de la grille. Réinstallez la grille après la peinture. 7 Specifications Modèle Sys ...