User manual JBL CONTROL NOW AW

® JBL CONTROL SERIES JBL CONTROL NOWTM JBL CONTROL NOWTM AW ® ® OWNER'S GUIDE TABLE OF CONTENTS UNPACKING THE SPEAKERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WALL SURFACE-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WALL CORNER-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 WALL/CEILING CORNER-MOUNTING . . . . . . . . . . . . . . . . . . 8 HALF-ROUND WALL-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . 10 3/4-ROUND WALL-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 STAND-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FOUR-SPEAKER-ARRAY INSTALLATION. . . . . . . . . . . . . . . . . . . 18 UNPACKING THE BRACKET AND CABLE KIT . . . . . . . . . . . 18 MAINTENANCE AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 JBL CONTROL NOWTM LOUDSPEAKERS For more than 60 years, we have been providing JBL® audio equipment for top concert halls, recording studios and movie theaters around the world, becoming the hands-down choice of leading recording artists and sound engineers. With JBL Control NOWTM loudspeakers, innovative technologies such as titaniumlaminate dome tweeters, PolyPlasTM transducer reinforcement and a patented, controlled-directivity Bi-Radial® horn are available to you. JBL Control NOW speakers are unique in their ability to deliver excellent performance over an extremely wide listening area. Therefore, the conventional placement guidelines outlined below can often be relaxed somewhat to offer you the flexibility of placing the speakers where they best integrate into your living environment, without sacrificing performance. UNPACKING THE SPEAKERS If you suspect damage from transit, report it immediately to your dealer. Keep the shipping carton and packing materials for future use. Included: JBL Control NOW Speaker (2) #10-32 x 2" (M5 51 mm) (2) #10-32 x 1/2" Screws (M5 13 mm) Screws Corner/Wall-Mount-Bracket Cap (1) "1/4-20 x 1" (M6 25 mm) Screw Corner/Wall-Mount Bracket Stand-Mount Bracket (2) Bracket Covers (2) #8-32 x 1/2" (M4 13 mm) Screws Multiunit Wiring Adapter 2 PLACEMENT JBL Control NOW speakers are perhaps the most flexible and versatile loudspeakers ever developed. There are numerous mounting options. The JBL Control NOW speaker can be wall-mounted or corner-mounted, sit on a shelf or be used with floor stands. Two, three or four speakers can be joined together to create loudspeaker solutions for virtually any application. · Use single units as shelf, stand- or wall-mounted speakers in traditional stereo or home theater applications. · Join two speakers together to form a visually striking array in single-channel applications or as a single-point stereo or surround speaker such as rear surround left and rear surround right. · Connect three speakers around an outer corner and send full-range sound throughout two adjacent rooms. · Suspend four JBL Control NOW speakers from the ceiling, using standard ceiling-fan hardware and the optional pole-mount bracket (not included). Configure each four-speaker array for use as a single-channel or single-point stereo. This owner's guide will cover the installation and wiring procedures for each mounting option. Simply decide how you will mount and use the speakers, and then follow the instructions for your specific application. Please note that while the JBL Control NOW AW speaker is an all-weather outdoor loudspeaker, it is not waterproof. The speaker should not be submerged or directly exposed to water, ice, snow or sustained moisture. JBL Control NOW speakers are designed for indoor use only. STEREO Before deciding where to place your speakers, survey your room and think about placement. Keep the following points in mind, and use Figure 1 as a guide: · For best results, place the speakers 6"­ 8" (1.5m­ 2.5m) apart. · Position each speaker so that the tweeter is directed toward the listening area. · Generally, bass output will increase as the speaker is moved closer to a wall or corner. · Refer to the "Home Theater" section at right if you also plan to use the speakers for home theater reproduction. HOME THEATER For front-channel use, place one speaker on the left and another on the right, along either side of the television monitor. Since the speakers are magnetically shielded, you can place them near a CRT TV without worrying about the field distorting the TV picture. For surround-channel use, place speakers in corners, on the wall, on bookshelves or on stands alongside the listening position. Final placement depends on room acoustics, availability of space and your listening preference. In 6- or 7-channel configurations, place the rear channel(s) behind the listening position, as shown in Figure 2. NOTE: A JBL powered subwoofer will add impact and realism to both music and film soundtracks. Contact your JBL dealer for recommendations on subwoofer models for your application. Left Front Channel Right Front JBL Channel Subwoofer (optional) Center Channel Couch Left Surround Channel Left Rear Channel Center Rear Channel Right Rear Channel Right Surround Channel Figure 2. This overhead view shows a typical home theater plan. Left/right rear channels are for a 7-channel system. The center rear channel is for a 6-channel system. Left Channel Right Channel Listening Position Figure 1. Experiment with speaker placement to obtain the best bass level and stereo imaging in your room. 3 English WALL SURFACE-MOUNTING When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2" (21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Please do not use any power tools during installation. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. 1. Run the wiring to the location desired for mounting the JBL Control NOW speaker. 2. Using a level, secure the mounting bracket to the wall. Be sure to use an appropriate anchor. Corner/Wall-MountBracket Assembly 3"(7,6 cm) Minimum distance from ceiling to top of bracket (horizontal mount) IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection 8-1/2"(21,5 cm) Minimum distance from ceiling to top of bracket (vertical mount) RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. Appropriate anchors NOTE: There are two cable access holes provided in the WallMount Assembly. 3. Connect the wires to the JBL Control NOW speaker. 4 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Rest the JBL Control NOW speaker's rear flange in the mounting bracket, as shown. This will support the weight of the speaker. Slide the mounting-bracket cap over the assembly. Secure the mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. Mounting-Bracket Cap An alternate vertical orientation is shown here Vertical orientation Mounting Bracket (side view) Bracket Cover #10-32 x 2" (M5 51 mm) Screws (2) (side view) Mounting-Bracket Cap Vertical orientation Mounting Bracket #10-32 x 2" (M5 51 mm) Screws (2) Bracket Cover Mounting Bracket shown as looking through the speaker. 5. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. The JBL logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket cover and attach to the top and bottom of the mounting assembly. Mounting-Bracket Cover Regardless of whether you choose a vertical or horizontal orientation, when mounting the JBL Control NOW speaker to a single wall surface, you should always install the wall-mounting bracket in a vertical orientation. Mounting-Bracket Cover 5 English WALL CORNER-MOUNTING CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Please do not use any power tools during installation. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2" (21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. 1. Run the wiring to the location desired for mounting the JBL Control NOW speaker. 3. Connect the wires to the JBL Control NOW speaker. IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + Corner/Wall-MountBracket Assembly The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. NOTE: There are two cable access holes provided in the WallMount Assembly. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection 2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors. Wiring diagram shows polarity connections for one channel of a stereo or home theater system. 3" (7,6 cm) Minimum distance from ceiling (horizontal mount) 8-1/2" (21,5 cm) Minimum distance from ceiling (vertical mount) RED = + BLACK = -- Appropriate anchors 6 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Rest the JBL Control NOW speaker's rear flange in the mounting bracket, as shown. This will support the weight of the speaker. Now slide the mounting-bracket cap over the assembly. Secure the mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. Mounting-Bracket Cap 5. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. The JBL logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket cover and attach to bottom of mounting assembly. Mounting Bracket (side view) Mounting-Bracket Cover #10-32 x 2" (M5 51 mm) Screws (2) (side view) Ceiling line Top Cap Mounting Bracket #10-32 x 2" (M5 51 mm) Mounting Bracket shown as looking through the speaker. 7 English WALL/CEILING CORNER-MOUNTING (VERTICAL MOUNTING ONLY) CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Please do not use any power tools during installation. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7,6 cm) to a side wall. Any closer than 3" (7,6 cm) will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. 3. Connect the wires to the JBL Control NOW speaker. IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. 3" (7,6 cm) Minimum distance from wall IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection 1. Run the wiring to the location desired for mounting the JBL Control NOW speaker. 2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors. BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. Appropriate anchors RED = + 8 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the side of the mounting bracket. Rest the JBL Control NOW speaker's flange in the mounting bracket, as shown. This will support the weight of the speaker. Now slide the mounting-bracket cap over the assembly. Secure the mountingbracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the side of the mounting bracket and tightening. 5. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. The JBL logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket cover and attach to sides of the mounting assembly. Bracket Cover #10-32 x 2" (M5 51 mm) Screws (2) Top Cap Mounting Bracket Mounting Bracket shown as looking through the speaker. #10-32 x 2" (M5 51 mm) Screws (2) Mounting Bracket Top Cap This illustration shows speaker viewed from beneath. 9 English HALF-ROUND WALL-MOUNTING (HORIZONTAL OR VERTICAL) NOTE: Decide whether you will connect the speakers as a single channel or two separate channels, and follow the appropriate instructions on the following pages. CONNECT AS A SINGLE CHANNEL CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Please do not use any power tools during installation. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. 1. Secure two corner/wall-mounting brackets together by using two #10-32 x 1/2" (M5 13 mm) screws provided, as shown. Attach the mounting bracket to the wall. 2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors. Appropriate anchors 3. Remove the terminal assemblies from the rear of both speakers. The terminal assembly is removed by giving it a slight counterclockwise rotation. Use the transparent plastic strap to pull the assembly out, as shown. #10-32 x 1/2" (M5 13 mm) Screws (2) When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2" (21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. 4. Connect the small end of the multiunit wiring adapter to one of the speaker rears, as shown. 3" (7,6 cm) Minimum distance from ceiling (horizontal mount) 8-1/2" (21,5 cm) Minimum distance from ceiling (vertical mount) 10 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Run the loose end of the multiunit wiring adapter through the rear cable-management hole in the mounting bracket, and rest the JBL Control NOW speaker's rear flange in the mounting bracket, as shown. This will support the weight of the speaker. Now slide the mountingbracket cap over the assembly. Secure the mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. 8. Now connect the wires to the terminal assembly. IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + Mounting-Bracket Cap The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection Mounting Bracket (side view) #10-32 x 2" (M5 51 mm) Screws (2) (side view) RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. 6. Place the large end of the multiunit wiring adapter into the second speaker to be installed. Slide the multiunit wiring adapter into the rear of the speaker at a slight angle and rotate clockwise. 9. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. The JBL logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket covers and attach to the top and bottom of the mounting assembly. Mounting-Bracket Covers Already connected to the other speaker. 7. Connect the terminal assembly to the back of the multiunit wiring adapter. It will snap securely into place. Mounting-Bracket Covers Already connected to the other speaker. 11 English CONNECT AS TWO CHANNELS CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Please do not use any power tools during installation. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. 1. Secure two corner/wall-mounting brackets together by using two #10-32 x 1/2" (M5 13 mm) screws provided, as shown. Attach the mounting bracket to the wall. 2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors. Appropriate anchors 3. Connect the wires to the terminal assembly of each of the JBL Control NOW speakers. #10-32 x 1/2" (M5 13 mm) Screws (2) IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2" (21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. 3" (7,6 cm) Minimum distance from ceiling (horizontal mount) 8-1/2" (21,5 cm) Minimum distance from ceiling (vertical mount) The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. 12 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting bracket cap with two screws through the bottom of the mounting bracket. This will support the weight of the speaker. Now slide the mounting-bracket cap over the assembly. Secure the mounting- bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. Repeat the process with the remaining speaker. Mounting-Bracket Cap 5. Now rest the second JBL Control NOW speaker's rear flange in the mounting bracket, as shown, and complete the process. Secure the mounting-bracket cap with two #10-32 x 2" (M5 51 mm) screws through the bottom of the mounting bracket. Mounting Bracket (side view) #10-32 x 2" Screws (2) #10-32 x 2" (M5 51 mm) Screws (2) (side view) 6. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. The JBL logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket covers and attach to the top and bottom of the mounting assembly. Mounting-Bracket Covers #10-32 x 2" (M5 51 mm) Screws (2) Mounting-Bracket Covers 13 English 3/4-ROUND WALL-MOUNTING Speaker 1 When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7,6 cm) to the ceiling. Any closer than 3" (7,6 cm) will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. ceiling 3" (7,5 cm) Minimum distance from ceiling to top of bracket (horizontal mounting) Speaker 2 Speaker 3 2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors. CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Please do not use any power tools during installation. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. 1. Secure three corner/wall-mounting brackets together by using four #10-32 x 1/2" (M5 13 mm) screws provided as shown. Appropriate anchors 3. Remove the terminal assemblies from the rear of all speakers. The terminal assembly is removed by giving it a slight counterclockwise rotation. Use the transparent plastic strap to pull the assembly out, as shown. #10-32 x 1/2" (M5 13 mm) Screws (2) #10-32 x 1/2" (M5 13 mm) Screws (2) 14 4. Connect the small end of the multiunit wiring adapter to the rear of speaker 1, as shown. 6. Place the large end of the multiunit wiring adapter that is already connected to speaker 1 into speaker 2 by sliding the multiunit wiring adapter into the rear of the speaker at a slight angle and rotate clockwise. This end is connected to the first speaker now resting in the Corner/Wall-Mount Bracket. 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Run the loose end of the multiunit wiring adapter through the rear cable-management hole in the mounting bracket and rest the JBL Control NOW speaker's rear flange in the mounting bracket, as shown. This will support the weight of the speaker. Slide the mountingbracket cap over the assembly. Secure the mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. 7. Connect the small end of an additional multiunit wiring adapter to the speaker rear as shown. This end is connected to the first speaker now resting in the Corner/Wall-Mount Bracket. 8. Rest the second JBL Control NOW speaker's rear flange in the mounting bracket, as shown, and complete the process. Secure the mounting bracket cap with two #10-32 x 2" (M5 51 mm) screws through the bottom of the mounting bracket. #10-32 x 2" (M5 51 mm) Screws (2) Mounting-Bracket Cap #10-32 x 2" Screws (2) Mounting Bracket (side view) #10-32 x 2" (M5 51 mm) Screws (2) (side view) 15 English 9. Place the large end of the multiunit wiring adapter that is already installed in speaker 2 into speaker 3 by sliding a multiunit wiring adapter into the rear of it at a slight angle and rotate clockwise. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. This end is connected to the second speaker currently resting in the Corner/Wall-Mount Bracket assembly. 12. Rest the third JBL Control NOW speaker's rear flange in the mounting bracket as shown and complete the process. Secure the mounting-bracket cap with 2 screws through the bottom of the mounting bracket. 10. Connect the terminal assembly to the back of the second multiunit wiring adapter. It will snap securely into place. The other end of the multiunit wiring adapter will already be connected to the other speaker already mounted in the corner/wall-mount bracket assembly. This end is connected to the second speaker currently resting in the Corner/Wall-Mount-Bracket Assembly. 11. Connect the wires to the terminal assembly and place the speaker on the remaining bracket. 13. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. The JBL logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket covers and attach to top and bottom of mounting-bracket assembly. Speaker 1 Mounting-Bracket Covers IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + Speaker 2 Speaker 3 The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. Mounting-Bracket Covers 16 STAND-MOUNTING IMPORTANT SAFETY NOTE: CAUTION The supplied floor stand adapters facilitate installation with a variety of generalpurpose floor stands available from many manufacturers. Since different stands will have different weight capacities and stability characteristics, it is the customer's responsibility to check with the stand manufacturer or dealer to ascertain whether that specific stand is capable of handling the weight and proportions of these loudspeakers in a safe and stable manner. JBL, Inc., disclaims any liability for the selection of suitable floor stands and/or correct compatibility between the selected stand and the supplied stand adapter. 1. Attach the stand-mounting bracket to the stand with the #1/4-20 x 1" (M6 25 mm) screw as shown. 2. Run the wiring as shown. IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + Note trough in Stand-Mount Bracket for cable management. The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. #1/4-20 x 1" (M6 25 mm) (M4 13 mm) Screw Provided IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection Stand-Mount Bracket Stand RED = + BLACK = -- 3. Place the JBL Control NOW speaker on the stand-mount bracket and stand, as shown. Wiring diagram shows polarity connections for one channel of a stereo or home theater system. An alternate orientation shown here. 4. Use two #8-32 x 1/2" (M4 13 mm) screws provided to secure the JBL Control NOW speaker to the stand. 5. Attach wires. #8-32 x 1/2" Screws 17 English FOUR-SPEAKER ARRAY USING THE OPTIONAL POLE-MOUNT BRACKET (PMB) CAUTION The JBL Control NOW PMB Pole-Mount Bracket facilitates installation of the JBL Control NOW and JBL Control NOW AW loudspeakers with a variety of general-purpose ceiling-fan-pole assemblies available from many manufacturers. Since different fan-pole assemblies will have different weight capacities, pole diameters and mounting systems, it is the customer's responsibility to check with the fan-pole-assembly manufacturer or dealer to determine whether that specific pole-mount assembly is capable of correctly and securely attaching to the PMB and handling the weight and proportions of these loudspeakers in a safe and stable manner. JBL, Inc., disclaims any liability for the selection of fan-pole assemblies and/or correct compatibility between the selected fan-pole assembly and the JBL Control NOW PMB. UNPACKING THE BRACKET AND CABLE KIT Carefully unpack the bracket and cable assembly. If you suspect damage from transit, report it immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Open the package and verify the following contents: SPEAKER IDENTIFICATION CHART Included: Pole Bushing (used for smaller-diameter drop tubes) ATTACHING POLE TO POLE-MOUNT BRACKET (FOR LARGER-DIAMETER DROP TUBES) 1. Run the appropriate wiring down through the drop tube. Slide the drop tube through the pole-mount-bracket cap. Pole-Mount-Bracket Cap Cotter Pin Clevis Pin Drop Tube Pole-Mount Bracket (4) #10-32 x 2" (M5 51 mm) Screws Pole-Mount-Bracket Cover Cable Assembly Pole-Mount-Bracket Cap 18 2A. Slide the pole-mount bracket up onto the drop tube, aligning the pinholes on the bracket with those on the drop tube. 3. Slide the clevis pin through the aligned holes in the pole-mount bracket and drop tube. Secure the clevis pin by inserting the cotter pin through the hole in the clevis pin. Pole-Mount Bracket Cap Pole-Mount-Bracket Cap Cotter Pin Drop Tube Drop Tube Pinholes Pole-Mount Bracket Pole-Mount Bracket Clevis Pin 4. The pole-mount bracket can now hold the weight of the speakers. (FOR SMALLER-DIAMETER DROP TUBES) 2B. When using a smaller drop tube, use the pole bushing when running the wiring down through pole-mount-bracket cap. This will help to eliminate pole wobble. Pole-Mount-Bracket Cap Drop Tube Pole-Mount Bracket Clevis Pin Pole Bushing 19 English SPEAKER WIRING There are four possible ways of wiring the JBL Control NOW speakers when using the pole-mount kit. 1. Use the cable assembly provided to wire the units for a single channel. 2B. Stereo sound distribution ­ Use this connection for a smaller home theater/stereo environment. Cable Assembly Channel 1 Channel 2 A B A Channel 1 B Channel 2 Multiunit Wiring Adapter D C Multiunit Wiring Adapter Channel 1 Single-channel-wiring diagram. D Terminal Assemblies Channel 2 C 2. Use the multiunit wiring adapters to wire the units for two channels. NOTE: There are two options for 2-channel wiring: 2A. Even sound distribution ­ Use this connection for even sound distribution through both channels. This may be more appropriate for larger rooms. 2-Channel-wiring diagram for stereo sound distribution. 3. Use four sets of cables to wire the units for four channels. Channel 2 Channel 1 Channel 1 Channel 2 Channel 3 Channel 4 A Channel 1 Multiunit Wiring Adapter B Channel 2 Multiunit Wiring Adapter A Channel 1 B Channel 4 Channel 2 Channel 1 D C Channel 2 Channel 3 D 4-Channel-wiring diagram. C 2-Channel-wiring diagram for even sound distribution. 20 SINGLE-CHANNEL WIRING 1. Use the cable assembly provided. Run the cable assembly down the drop tube; run the four sets of paired wires out through the wire access holes, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + Pole-Mount-Bracket Cap The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. Drop Tube IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection Pole-Mount Bracket Wire Access Holes RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. Single-channel wiring. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. 2. Connect the wires to the terminal assembly of each speaker as shown. Place the speaker on the mounting bracket, as shown in step 6 of the mounting- bracket-installation procedures. Return to the installation procedures and continue. 21 English 2-CHANNEL WIRING FOR EVEN SOUND DISTRIBUTION 1. Use the even sound distribution connection for even sound distribution through both channels. Run the sets of paired wires out two wire access holes through the pole-mount bracket, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. 3. Connect the small end of the multiunit wiring adapter to the rear of speakers A and B, as shown. Pole-MountBracket Cap 4. Place speakers A and B with connectors attached on the pole-mount bracket, as shown. Run the wiring for the multiunit wiring adapter through the wire access holes, as shown. Drop Tube A Pole-Mount-Bracket Cap Drop Tube B Pole-Mount Bracket Connector Connector Pole-Mount Bracket Wire Access Holes Multiunit Wiring Adapter to connect to speaker D Wire Access Holes Multiunit Wiring Adapter to connect to speaker C 2-Channel-wiring for even sound distribution. 5. Slide the large end of the multiunit wiring adapter that is already attached to speaker A into the rear of speaker C at a slight angle and rotate clockwise, as shown. 2. Remove the terminal assemblies from the rear of all speakers. The terminal assembly is removed by rotating it slightly counterclockwise, as shown. This end is connected to speaker A. 6. Connect the terminal assembly to the back of the multiunit wiring adapter, as shown. It will snap securely into place. Use the transparent plastic strap to pull the terminal assembly out, as shown. This end is connected to speaker A. 22 7. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker D. Return to the installation procedures and continue. IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. 23 English 2-CHANNEL STEREO WIRING 1. Use the stereo sound-distribution connection for a smaller home theater/stereo environment. Run the sets of paired wires out two opposite wire access holes through the pole-mount bracket, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. 3. Connect the small end of the multiunit wiring adapter to the rear of speakers D and B, as shown. Pole-Mount-Bracket Cap 4. Place speakers D and B with connectors attached on the pole-mount bracket, as shown. Run the wiring for the multiunit wiring adapter through the wire access holes, as shown. Drop Tube Drop Tube Multiunit Wiring Adapter to connect to speaker A Pole-Mount-Bracket Cap Pole-Mount Bracket D Connector Pole-Mount Bracket Multiunit Wiring Adapter to connect to speaker C B Connector Wire Access Holes Wire Access Holes 2-Channel-wiring for stereo sound distribution. 2. Remove the terminal assemblies from the rear of all four speakers. The terminal assembly is removed by rotating it slightly counterclockwise, as shown. 5. Slide the large end of the multiunit wiring adapter that is already attached to speaker B into the rear of speaker C at a slight angle and rotate clockwise, as shown. This end is connected to speaker B. Use the transparent plastic strap to pull the terminal assembly out, as shown. 6. Connect the terminal assembly to the back of the multiunit wiring adapter. It will snap securely into place. This end is connected to speaker B. 24 7. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker A. Return to the installation procedures and continue. 4-CHANNEL WIRING 1. Run the four sets of paired wires out the wire access holes, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. Pole-Mount-Bracket Cap Drop Tube IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Strip 1/4" (6 mm) of wire 2. Press and push connector 3. Insert bare end; release push connector BLACK = -- RED = + Pole-Mount Bracket The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in the diagram to the left. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. Wire Access Holes 4-Channel wiring. IMPORTANT: Do not reverse polarities (i.e., + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Standard Connection 2. Connect the wires to the terminal assembly of each speaker, as shown, and place the speaker on the mounting bracket, as shown in step 6 of the mounting-bracket-installation procedures. Return to the installation procedures and continue. RED = + BLACK = -- Wiring diagram shows polarity connections for one channel of a stereo or home theater system. 25 English SPEAKER MOUNTING After carefully placing all four speakers in the mounting bracket, lightly jostle the speakers into place so that the pole-mount-bracket cap will slide down into place. Tighten the pole-mount-bracket assembly with the four #10-32 x 2" (M5 51 mm) screws provided. Drop Tube Pole-Mount-Bracket Cap Pole-Mount Bracket #10-32 x 2"(M5 51 mm) Screws (4) Only two speakers shown here for clarity. Place the pole-mount-bracket cover over the bottom visible mounting bracket by snapping it into place. Drop Tube Pole-Mount Bracket Cap 26 MAINTENANCE AND SERVICE The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the minimum. If a problem occurs, make sure that all connections are properly made and clean. If a problem exists in one loudspeaker, reverse the connection wires to the left and right system. If the problem remains in the same speaker, then the fault is with the loudspeaker. If the problem appears in the opposite speaker, the cause is in another component or cable. In the event that your speaker ever needs service, contact your local JBL dealer or distributor or visit www. jbl.com for a service center near you. NOTE: The serial number is located on the rear of the speaker housing. To view it, remove the four screws on the rear assembly as shown. The product identification label is located behind the rear housing bracket. The serial number is located on the back top area of the speaker housing between the two top rear bracket-bolt holes. 27 English SPECIFICATIONS JBL CONTROL NOWTM JBL CONTROL NOWTM AW Frequency Response (­6dB) Max. Recommended Amplifier Power* Power Handling (Continuous/Peak) Sensitivity (2.83V/1m) Nominal Impedance Crossover Frequencies Low-Frequency Transducers High-Frequency Transducer Weight per Speaker 80Hz ­ 30kHz 150W 50W/300W 90dB 8 Ohms 2000Hz ­ 18dB/octave; woofer 36dB/octave tweeter; Dual 4" (100mm) PolyPlas, shielded TM