993AS-L/993AS /993AN USER'S MANUAL PCIAGP Mainboard For Pentium II/ III or Socket 370 The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to update the information contained herein. NO. G03-993ANR3A Release date: NOV 2000 ** Year 2000 compliant ** Trademark: * Pentium is registered trademark and MMX is a trademark of Intel corporation, the other names and brands are the property of their respective owners. * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT Chapter 1 1-1 Preface............................................................................................................. 1 1-2 Feature of motherboard ................................................................................... 1 1-2-1 Overview.............................................................................................. 1 1-2-2 Key Feature ......................................................................................... 2 Chapter 2 Hardware Installation..................................................................................3 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 Unpacking ........................................................................................................ 3 Mainboard Diagram.......................................................................................... 4 Quick Reference for Jumpers, Connectors & Expansion Socket ....................... 5 Installation Steps.............................................................................................. 6 Jumper Settings ............................................................................................... 6 System Memory (DRAM).................................................................................. 7 Central Processing Unit (CPU)......................................................................... 7 Expansion Cards .............................................................................................. 11 External Connectors......................................................................................... 11 Chapter 3 AWARD BIOS SETUP..................................................................................18 3-1 STANDARD CMOS SETUP ............................................................................. 19 3-2 BIOS FEATURES SETUP................................................................................ 20 3-3 CHIPSET FEATURES SETUP......................................................................... 21 3-4 POWER MANAGE MENT SETUP ................................................................... 22 3-5 PnP/PCI CONFIGURATION SETUP ............................................................... 24 3-6 LOAD OPTIMAL DEFAULTS ........................................................................... 24 3-7 LOAD STANDARD DEFAULTS ....................................................................... 25 3-8 INTEGRATED PERIPHERALS SETUP............................................................ 25 3-9 SUPERVISOR/USER PASSWORD ................................................................. 26 3-10 SAVE & EXIT SETUP ..................................................................................... 26 3-11 EXIT WITHOUT SAVING................................................................................ 26 Chapter 4 Software Installation......................................................................... 27 4-1 Mainboard Driver Install in Win9X,WinNT ........................................................ 27 4-2 PC HEALTH MONITOR-III (Option for motherboard that embedded PC Health chip)...... 28 4-3 SOUND Driver (Option for motherboard that embedded Audio chip)................ 30 APPENDIX-A Magic Install i Chapter 1 1-1 Preface Thank you for purchasing this multifunction motherboard. It has the most flexibility you can find in today's computer market. The mainboard integrates both Intel Pentium®II / Pentium®III & CeleronTM(Slot 1 & Socket 370) processor interface into a compact PC/AT compatible system along with 3D Stereo Sound System audio chip. Moreover, this mainboard allows you conditionally approach 150MHz * of Front Side Bus Frequency. 1-2 Feature of motherboard This motherboard is design for the PC user who wants highest possible quality and value in a small package. It includes following main features 1-2-1 Overview · · · · · · Support both Slot 1 & Socket 370 CPU interface (You can only use one CPU interface at a time). Support Ultra DMA 66 for newer hard disk interface. Support Jump-less solution for setting Front Side Bus Frequency (CPU Host Clock) and CPU ratio under CPU Host/PCI clock of CHIPSET FEATURES SETUP. Support CPU Host Clock and DRAM Clock Asynchronous/Synchronous mode, please refer page 18 " DRAM Clock". Conditionally support 66MHz~150MHz * of Front Side Bus Frequency. This function allow user select CPU Bus Frequency by the BIOS to approach Over-Clock possibility. Provide PC Health Monitoring to track CPU temperature, system temperature, system voltage, and fan speed. When CPU current temperature is over CPU warning temperature, system will slow down automatically in order to reduce the CPU's temperature. (Option for motherboard that embedded PC Health chip) Logo-DIY: Provide CBROM utility for user to create their own loge in the BIOS. Built in high quality PCI-Based HRTF 3D Extension Positional Audio Chip (Option for motherboard that embedded Audio chip) - Supports rear side speakers, C3DX positional audio in 4 channels speaker mode. - Professional digital audio interface to support 24-bit SPDIF IN and OUT (44.1K and 48K format). - HRTF-base 3D positional audio, supporting DirectSoundTM 3D and Aural A3DTM interface. - Digital functions that capable to provide hi-fi stereo, Dolby, 3D surround effects, and playing MP3 music. You can add our Optical kit (Option for motherboard that embedded Audio chip) to connect any optical Input/Output device for super high quality sound transaction, such as playing & recording MD(Mini Disk)/CD; CD-ROM directly recording to MD; combine with DVD player to create a home theater system (This upgrade kit includes Optical Module, Optical Cable, and Software DVD Driver). · · · 1 1-2-2 Key Feature · · · · · · Multi-Speed Support Provide 66/75*/83*/95*/100/112*/117*/124*/133*/150*MHz Front Side Bus Frequency to support Intel Pentium®II / Pentium®III, Celeron processor for Slot1 interface or Intel Celeron PPGA on a ZIP Socket 370 interface. Chipset VIA Apollo Pro AGPset . DRAM Memory SupportSupport 3 x 168-pin DIMM sockets (3.3V) for memory from 8M Byte to 1.5GB Byte in either EDO (66MHz only) or SDRAM (66MHz/100MHz/133 MHz) type module with ECC or parity check. AGP, ISA, and PCI expansion SlotsProvide an AGP slot, one 16-bit ISA slot, and four 32-bit PCI master slots. Super Multi-I/O: Provides two high-Speed UART compatible serial ports and one parallel port with EPP and ECP capabilities. Two floppy drives of either 5.25" or 3.5" (1.44MB or 2.88MB) are also supported without an external card. PCI Bus Master IDE Controller and ULTRA DMA 33/66 : On-board PCI Bus Master IDE controller with two connectors that supports four IDE devices in two channels, provides faster data transfer rates, and supports Enhanced IDE devices such as Tape Backup, CDROM, ZIP, LS-120 Drives. This controller also supports PIO Modes and Bus Master IDE Ultra DMA 33/66Mbyte/Second. ACPI supporting for OS Directed Power Management. Ring-In Wake up: When Ring-In the system can wake up from SMI Mode. Ring-In Power On: When Ring-In the system can power on automatic by this function. RTC Power On: Enabled RTC Power On function, you can set RTC alarm to power on the system at the time length that correspond to your setting. Power Button: Press the button will place the system power on/off. Wake on LAN : The system can power on by server in Network. Support Software Power Off function. Power Support: Efficient PWM switching power instead of traditional Linear Voltage Regulator to prevent power component from being burned-out. PC 99 ready PS/2 Mouse: This mainboard support PS/2 mouse set. USB Port Connector: This mainboard supports two USB port connectors for USB devices. Optional IrDA: This mainboard supports an optional infrared port module for wireless interface, with independent 3rd UART (32-byte FIFO). AGP: Accelerated Graphics Port, for to 533MB/sec data transfer rate and 66/133MHz Bus clock to improve graphic functions. ATX Form Factor: Dimensions 30.5cm x 19cm. Your memory module(s) must be PC133 compliant SDRAM chips and specified to run on 133MHz or 150MHz. When you are running at 150MHz, make sure all of your PCI devices have enough tolerance to run on 37.5MHz . Otherwise, it may cause your system become very unstable. · · · · · · · · * * 2 Chapter 2 Hardware Installation 2-1 Unpacking This mainboard package should contain the following: · · · · The mainboard USER'S MANUAL for mainboard Cable set for Ultra DMA 66 IDE x1, Floppy x1 CD for Drivers PACK The mainboard contains sensitive electronic components that can be easily damaged by electron-static, so the mainboard should be left in its original packing until it is installed. Unpacking and installation should be done on a grounded anti-static mat. The operator should be wearing an anti static wristband, grounded at the same point as the antistatic mat. Inspect the mainboard carton for obvious damage. Shipping and handling may cause damage to your board. Be sure there are no shipping and handling damages on the board before proceeding. After opening the mainboard carton, extract the system board and place it only on a grounded anti-static surface component side up. Again inspect the board for damage. Press down on the entire socket IC's to make sure that they are properly inserted. Do this only on with the board placed on a firm flat surface. Warning: Do not apply power to the board if it has been damaged. You are now ready to install your mainboard. The mounting hole pattern on the mainboard matches the ATX system board. It is assumed that the chassis is designed for a standard ATX main board mounting. Place the chassis on the anti-static mat and remove the cover. Take the plastic clips, Nylon stand-off and screws for mounting the system board, and keep them separate. 3 2-2 Mainboard Diagram J3 MINI- DIN CPUFAN ATX POWER CONN. SLOT-1 PL1 U18 DIM M 1 DIM M 2 DIM M 3 USB J1 J4 U10 C PU PAR ALLELPO T R ZIF SO KE 370 CT CO M1 DIMM1 DIMM2 BT1 C C M2 OO M2 J5 SL T-1 O U11 J2 GAM E MIC LINE-IN LINE-OUT VIA Apollo Pro AG C JP12 SYSFAN U7 C MI8738B JP11 JP2 JP3 IR1 AGP AGP1 IDE2 IDE1 IDE2 IDE1 S P K IN 1 S P D IF IN 1 S P D IF O U T JP4 JP7 FDD JP 1 FDD PCI1 BATT. + JP14 PCI 1 PCI2 PCI4 PCI 4 SL1 KEYLO K TBSW C PCI 3 V IA 8 2 C 5 9 6 B WOL Figure 2-2 Option for motherboard that embedded Audio chip 4 JP13 SPE R R TBLE HDLE AKE ST D D BIO S PCI3 N SMI PS-O PCI 2 U16 DIMM3 2-3 Quick Reference for Jumpers, Connectors & Expansion Socket Jumpers Jumper JP11,JP12 U18 JP14 Name CPU Bus Frequency Selection CPU Ratio Selector CMOS RAM Clear Description Refer to page 6 Refer to page 6 1-2 Normal ,2-3 Clear CMOS Page p. 6 p. 6 p. 7 Connectors Connector PL1 MINI-DIN USB PRINT COM1, COM2 FDD IDE1 IDE2 HDLED SMI JP13 IR1 CPUFAN, SYSFAN PS-ON WOL Name ATX Power Connector PS/2 Keyboard/PS/2 Mouse USB Port Connector Parallel Port Connector Serial Port COMA , COMB Floppy Driver Connector Primary IDE Connector Secondary IDE Connector IDE activity LED SMI Suspend Switch Front Panel Connector Infrared Module Connector FAN Connector ATX power button/soft power button Wake On LAN Description 20-Pin Block 6-Pin Female 5-Pin Connector 26-Pin Female 9-Pin Connector 34-Pin Block 40-Pin Block 40-Pin Block 2-Pin Connector 2-Pin Connector 16-Pin Block 10-Pin Block Extra fanning system connectors 2-Pin Connector 3-pin Block Page p.9 p.9 p.9 p.9 p.10 p.10 p.10 p.11 p.11 p.11 p.11 p.12 p.12 p.12 P.13 Jumpers & Connectors (Option for motherboard that embedded Audio chip) Item number JP4 JP1 JP2 JP3 AGC SPKIN 1 SPDIFIN 1 SPDIFOUT JP7 Name On-Board Sound Enable/Disable AUX IN CD-Audio CD-Audio Line IN/Line Out/MIC /Game Connector PC Speaker In SPDIF (Sony/Philips Digital Interface) IN SPDIF (Sony/Philips Digital Interface) OUT For Optional Optical Kit Connector Description 1-2 : Disabled , 2-3 : Enabled 4-pin Block 4-pin Block 4-pin Block 15-pin Connector + 3 phone jack 2-pin Block 3-pin Block 2-pin Block 10-pin Connector Page p.13 p.13 p.13 p.13 p.13 p.14 p.14 p.14 p.14 Expansion Sockets Socket/Slot DIMM1,DIMM2, DIMM3 Slot1 Zip Socket370 AGP SLOT PCI1, PCI2,PCI3 ,PCI4 SL1 CPU Slot CPU Socket AGP SLO ...