User manual JETWAY P4XFBU

P4XFB/P4XFBU USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-P4XFBR1A Release date: September 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE .............................................................................. ii MANUAL REVISION INFORMATION ............................................. 1 COOLING SOLUTIONS .................................................................. 1 CHAPTER 1 INTRODUCTION OF P4XFB/P4XFBU MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD............................................................... 2 SPECIFICATION .......................................................................................... 3 PERFORMANCE LIST ................................................................................ 4 LAYOUT DIAGRAM & JUMPER SETTING ........................................... 5 CHAPTER 2 HARDWARE INSTALLATION 2-1 HARDWARE INSTALLATION STEPS ..................................................... 7 2-2 CHECKING MOTHERBOARD'S JUMPER SETTING .......................... 7 2-3 INSTALL CPU ............................................................................................... 8 2-3-1 GLOSSARY ........................................................................................ 8 2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU.................................... 9 2-4 INSTALL MEMORY .................................................................................... 9 2-5 EXPANSION CARD ...................................................................................... 10 2-5-1 2-5-2 2-5-3 2-5-4 PROCEDURE FOR EXPANSION CARD INSTALLATION ..................10 ASSIGNING IRQ FOR EXPANSION CARD ............................................ 11 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD.......... 11 AGP SLOT .....................................................................................................11 2-6 CONNECTORS, HEADERS ........................................................................ 12 2-6-1 CONNECTORS .............................................................................................12 2-6-2 HEADERS ...................................................................................................... 15 2-7 STARTING UP YOUR COMPUTER.......................................................... 18 CHAPTER 3 INTRODUCING BIOS 3-1 3-2 3-3 3-4 3-5 3-6 ENTERING SETUP....................................................................................... 19 GETTING HELP............................................................................................ 19 THE MAIN MENU ........................................................................................ 20 STANDARD CMOS FEATURES................................................................. 21 ADVANCED BIOS FEATURES .................................................................. 22 ADVANCED CHIPSET FEATURES .......................................................... 24 3-6-1 DRAM TIMING SETTINGS ............................................................ 25 3-6-2 AGP FUNCTION SETTINGS .......................................................... 26 3-6-3 PCI TIMING SETTINGS.................................................................. 26 3-7 INTEGRATED PERIPHERALS.................................................................. 26 3-7-1 ONCHIP IDE FUNCTION................................................................ 27 3-7-2 ONCHIP DEVICE FUNCTION ....................................................... 28 3-7-3 ONCHIP SUPER IO FUNCTION .................................................... 29 3-8 POWER MANAGEMENT SETUP.............................................................. 30 3-8-1 PM WAKE UP EVENTS .................................................................. 31 i 3-8-1.1 IRQS ACTIVITIES ......................................................................... 31 3-9 PNP/PCI CONFIGURATION SETUP......................................................... 32 3-9-1 IRQ RESOURCES ............................................................................ 33 3-10 PC HEALTH STATUS................................................................................. 33 3-11 MISCELLANEOUS CONTROL ................................................................ 34 3-12 LOAD STANDARD/OPTIMIZED DEFAULTS ....................................... 35 3-13 SET SUPERVISOR/USER PASSWORD ................................................... 35 CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION MAGIC INSTALL SUPPORTS WINDOWS 9X/ME/NT4.0/2000/XP.............. 36 4-1 VIA 4 IN 1 INSTALL VIA SERVICE PACK 4 IN 1 DRIVER ..................... 37 4-2 SOUND INSTALL ALC AUDIO CODEC DRIVER ............................... 39 4-3 USB2.0 INSTALL USB2.0 DRIVER .................................................... 40 4-4 PC-HEALTH WINBOND HARDWARE DOCTOR MONITORING SOFTWARE 41 4-5 MAGIC BIOS INSTALL BIOS LIVE UPDATE UTILITY................................ 42 4-6 PC-CILLIN INSTALL PC-CILLIN2002 ANTI-VIRUS PROGRAM ............. 43 4-7 HOW TO DISABLE ON-BOARD SOUND................................................. 45 4-8 HOW TO UPDATE BIOS ............................................................................. 45 USER'S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE P4XFB/P4XFBU MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER'S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE). PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER'S BENEFIT, WITHOUT INTENT TO INFRINGE. ii Manual Revision Information Reversion 1.0 Revision History First Release Date September 2002 Item Checklist P4XFB/P4XFBU motherboard Cable for IDE/Floppy CD for motherboard utilities Cable for USB Port 3/4(Option) P4XFB/P4XFBU User's Manual Intel Pentium 4 Processor Family Cooling Solutions As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable, long-term system operation. The overall goal in providing the proper thermal environment is keeping the processor below its specified maximum case temperature. Heatsinks induce improved processor heat dissipation through increased surface area and concentrated airflow from attached fans. In addition, interface materials allow effective transfers of heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of thermal grease and mounting clips to attach the heatsink to the processor. When selecting a thermal solution for your system, please refer to the website below for collection of heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are recommended for maintaining the specified Maximum T case requirement. In addition, this collection is not intended to be a comprehensive listing of all heatsinks that support Intel processors. For vendor list of heatsink and fan, please visit : http://developer.intel.com/design/Pentium4/components/index Chapter 1 1 Introduction of P4XFB/P4XFBU Motherboard 1-1 Feature of motherboard The P4XFB/P4XFBU motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the VIA P4X266E Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB. These motherboards use the newest VIA P4X266E Chipset. Supports 533MHz System Bus in data transfer rate for P4XFB. The motherboard provided 100MHz/133MHz Memory clock frequency, support PC133/PC100 SDRAM and DDR266/DDR200 DDR Module. The VIA VT8233A V-Link LPC South Bridge offer ULTRA ATA 133 to provide speedier HDD throughout that boosts overall system performance. These motherboards also has an integrated AC'97 2.1 CODEC on board which is fully compatible with Sound Blaster Pro that gives you the best sound quality and compatibility. For those wanting even greater graphic performance, an AGP 4X slot is included on the board, support AGP 2X/4X capability and Fast write Transaction. With USB control as well as capability of expanding to 4x USB2.0 function ports delivering 480Mb/s bandwidth, and 2x USB1.1 function ports delivering 12Mb/s bandwidth in P4XFBU, 4x USB1.1 function ports in P4XFB delivering 2x12Mb/s bandwidth and rich connectivity, these motherboards meet future USB demand also has built-in hardware monitor function to monitor and protect your computer. A useful software tool "Magic BIOS" examines the BIOS version automatically with the correct version available on the web, links the site for users to download the latest version of BIOS and updates the BIOS. Use "Magic BIOS", users can download and update BIOS automatically and completed under the OS easily. These motherboards provide high performance & meets future specification demand. It is really wise choice for your computer. 1-2 Specification 2 Spec Design Chipset CPU Socket (mPGA478B Socket) Description ATX form factor 4 layers PCB size: 30.5x21.0cm VIA P4X266E North Bridge Chipset VIA VT8233A South Bridge Chipset Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package processor Support 1.5G2.66G 478 Pin Pentium 4 processor Reserves support for future Intel Pentium 4 processors 168-pin SDR SDRAM module socket x1 and 184-pin DDR Module socket x 2 Support 1 pcs PC133/PC100 SDRAM Module expandable to 1.0GB, or 2 pcs DDR266/DDR200 DDR Modules Expandable to 2.0GB AGP slot x1 support AGP 2.0 & 4X mode 32-bit PCI slot x5 Two PCI IDE controllers support PCI Bus Mastering, ATA PIO/DMA and the ULTRA DMA 33/66/100/133 functions that deliver the data transfer rate up to 133 MB/s VIA VT 6202 USB2.0 chip Provided 4xUSB2.0 ports support 480Mb/s bandwidth for USB2.0 devices . AC'97 Digital Audio controller integrated AC'97 Audio CODEC on board Audio driver and utility included Award 2MB Flash ROM PS/2 keyboard and PS/2 mouse connectors Floppy disk drive connector x1 Parallel port x1 Serial port x2 USB connector x2 for P4XFB/P4XFBU USB headers x2 (connecting cable option) for P4XFB USB headers x 4 (connecting cable option) for P4XFBU Audio connector (Line-in, Line-out , MIC & Game Port) Memory Socket Expansion Slot & Headers Integrate IDE USB2.0 (Only for P4XFBU) Audio BIOS Multi I/O 1-3 Performance List 3 The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report Intel Pentium 4 1.9GHz mPGAB package 256MB DDR266 x1 (SAMSUNG K4H280838B-TCB0) 256MB SDRAM x1 (KINGMAX KSV684T4A1A-06) VGA Expansion Card: NVDIA Geforce2 MX-400 64MB (1024x768xHi-color) IBM DTLA-305040 (ATA-100) Hard Disk Driver: Award Optimal default BIOS: Win 98SE OS: CPU: DRAM: DDR266 PC133 SDRAM 3D Mark 2000 5432 5360 3D Mark 2001 2509 2479 3D Winbench 2000 104 102 Final Reality 9.99 9.06 Content Creation Winstone 2000 43.2 41.5 Content Creation Winstone 2001 50.3 49.5 Content Creation Winstone 2002 20.1 18.6 Business Winstone2001 44.1 42.8 Winbench 99: CPU Mark 99 111 101 FPU Winmark 99 6610 6610 Business Disk Winmark99 7150 7090 Hi-end Disk Winmark99 18800 18500 Business Graphic Winmark 434 428 Hi-end Graphic Winmark 1260 1230 SYS Mark 2000/2001 : SISMark 2000/2001 Rating (Internet Content Creation / Office Productivity) SISMark 2000 208 (226/195) 200 (217/188) SISMark 2001 150 (175/129) 142 (160/126) SISOFT Sandra 2001 : Dhrystone ALU MIPS 3626 3630 Whetstone FPU MFLOPS 1137/2371 1135/2368 Int ALU/RAM MB/S 1181 701 Float FPU/RAM MB/S 1183 701 Integer SSE2 IT/S 7547 7554 Floating-Point SSE2 IT/S 9352 9350 QUAKE3 DEMO1 FPS 169.1 146.7 DEMO2 FPS 169.7 146.1 WCPUID System/CPU Clock 101/1918.93 101/1918.93 1-4 Layout Diagram & Jumper Setting PS/2 MOUSE PRINT GAME/MIDI PORT 4 MIC K/B Power ON Jumper (JP1) PS2 KB/Mouse Port USB Port ATX 12V Power Conn. ATX Power Conn. CPU FAN PC99 Back Panel CPU Socket SDR SDRAM DIMM x1 DDR SDRAM DIMM x2 Front Panel Audio ATX P9 Power Conn. VIA P4X266E Chip CD Audio System FAN AGP Slot VIA VT8233A Chip PCI Slot VIA VT6202 Chip ATA 133 IDE Conn. Floppy Connector Clear CMOS (JBAT) Front Panel Connector IR Connector Speaker Conn. Winbond W83697HF Chip System FAN1 2MBit Flash ROM BIOS Wake On LAN USB3 Port (for P4XFBU) USB1 Port Jumpers Jumper Name Description Page 5 JBAT JP1 CMOS RAM Clear Keyboard Power On Enable/Disabled Name ATX Power Connector ATX 12V Power Connector ATX P9 Power Connector PS/2 Mouse & PS/2 Keyboard Connector USB1.1 Port Connector for P4XFB USB2.0 Port Connector for P4XFBU Parallel Port Connector Audio/Game Connector Serial Port COM1/2 Connector Floppy Driver Connector Primary/Secondary IDE Connector 3-pin Block 3-pin Block Description 20-pin Block 4-pin Block 6-pin Block 6-pin Female 4-pin Connector 25-pin Female 3 phone jack+15-pin Connector 9-pin Connector 34-pin Block 40-pin Block P.7 P.7 Page P.12 P.12 P.13 P.13 P.13 P.13 P.13 P.13 P.14 P.14 Connectors Connector ATXPWR ATX12V ATXP9 PS2KBM CN1 COM_LP AUDIO_GAME COM1/COM2 FDD IDE1/IDE2 Headers Header AUDIO USB1 USB3 (for P4XFBU) HD-LED RESET SPEAK PWR-LED PWR-BTN WOL SFAN1, SYSFAN, CPUFAN IR CD_IN Name SPEAKER, MIC header USB1.1 Port Headers USB2.0 Port Headers IDE activity LED Reset switch lead PC Speaker connector Power LED Power switch Wake On-LAN Headers FAN Headers IR infrared module Headers CD Audio-In Headers Description 9-pin Block 9-pin Block 9-pin Block 2-pin Block 2-pin Block 4-pin Block 2-pin Block 2-pin Block 3-pin Block 3-pin Block 5-pin Block 4-pin Block Page P.15 P.15 P.15 P.15 P.16 P.16 P.16 P.16 P.16 P.17 P.17 P.17 Expansion Sockets Socket/Slot ZIF Socket 478 Pin SDR1 DDR1, DDR2 PCI1 PCI5 AGP Name CPU Socket SDRAM Module Socket DDR Module Socket PCI Slot AGP 4X Mode Slot Description 478-pin mPGA CPU Socket 168-pin SDR SDRAM Module Expansion Socket 184-pin DDR Module expansion Socket 32-bit PCI Local Bus Expansion slots AGP Expansion Slot Page P.9 P.9 P.9 P.10 P.11 Hardware installation Chapter 2 6 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10. Install Driver and Utility 2-2 Checking Motherboard's Jumper Setting (1) CMOS RAM Clear (3-pin) : JBAT A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JBAT to store the CMOS data. To clear the CMOS, follow the procedure below: 1. Turn off the system and unplug the AC power 2. Remove ATX power cable from ATX power connector 3. Locate JBAT and short pins 2-3 for a few seconds 4. Return JBAT to its normal setting by shorting pins 1-2 5. Connect ATX power cable back to ATX power connector Note: When should clear CMOS 1. Troubleshooting 2. Forget password 3. After over clocking system boot fail JBAT 1 3 JBAT 1 3 1-2 closed Normal 2-3 closed Clear CMOS CMOS RAM Clear Setting (2) Keyboard Power On function Enabled/Disabled: JP1 When setting Enabled you can using keyboard by key in password to power on system. 7 JP1 1 JP1 1 3 3 1-2 closed (Default) K/B Power ON Disable 2-3 closed K/B Power ON Enabled Keyboard Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter cards. Processor slot/socket - the slot or socket used to mount the system processor on the motherboard. Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM. AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X (66MHz), 2X (133MHz), or 4X (266MHz). PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound cards, network interface cards, and modems; runs at 33MHz. ISA - Industry Standard Architecture - a relatively low speed interface primarily used for sound cards and modems; runs at approx. 8MHz. Serial Port - a low speed interface typically used for mouse and external modems. Parallel Port - a low speed interface typically used for printers. PS/2 - a low speed interface used for mouse and keyboards. USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards, scanners, and some digital cameras. Sound (interface) - the interface between the sound card or integrated sound connectors and speakers, MIC, game controllers, and MIDI sound devices. LAN (interface) - Local Area Network - the interface to your local area network. BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software. Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing the "computing" in "personal computer" Front Side Bus Frequency - the working frequency of the motherboard, which is generated by the clock generator for CPU, DRAM and PCI BUS. CPU L2 Cache - the flash memory inside the CPU, normal it depend on CPU type. 8 2-3-2 About Intel Pentium 4 478-pin CPU This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system. WARNING! Be sure that there is sufficient air circulation across the processor's heatsink and CPU cooling FAN is working correctly, otherwise it may cause the processor and motherboard overheat and damage, you may install an auxiliary cooling FAN, if necessary. To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and open it by first pulling the level sideways away from the socket then upward to a 90-degree angle. Insert the CPU with the correct orientation as shown below. The notched corner should point toward the end of the level. Because the CPU has a corner pin for two of the four corners, the CPU will only fit in the orientation as shown. mPGA478B Colden Arrow CPU ZIF mPGAB Socket When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press the level to Locate position slightly without any extra force. 2-4 Install Memory This motherboard provides two 184-pin DDR DUAL INLINE MEMORY MODULES (DIMM) sites for DDR memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB SDR SDRAM, or one 168-pin SDR DIMM sites for SDRAM memory for maximum memory size of 1.0GB. Valid Memory Configurations Bank Bank 0, 1 (DDR1) Bank 2, 3 (DDR2) Total Bank Bank 0, 1 (SDR1) Total 184-pin DDR DIMM DDR266/DDR200 DDR DRAM Module DDR266/DDR200 DDR DRAM Module System Memory (Max. 2.0GB) 168-pin SDR DIMM PC133/PC100 SDR DRAM Module System Memory (Max. 1.0GB) X1 X1 X2 X1 X1 Total Memory 64MB1.0GB 64MB1.0GB 64MB2.0GB Total Memory 64MB1.0GB 64MB1.0GB 9 Generally, installing SDR/DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 168-pin SDR/184-pin DDR SDRAM module looks like. DDR (BANK 1 0+BANK1) DDR (BANK 2 2+BANK3) SDR (BANK0+BANK 1 1) Figure 2-4 NOTE! WARNING! When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. For the SDR SDRAM CLOCK is set at 133MHz, use only PC133/DDR266compliant SDR/DDR Modules. When this motherboard operate at 133Mhz, most system will not even boot if non-compliant modules are used because of the strict timing issues, if your SDR/DDR Modules are not PC133/DDR266-compliant, set the SDRAM clock to 100MHz to ensure system stability. NOTE! It is only can install either SDRAM or DDR Module at one time. Don't install both DDR Module and SDR Module at same time, it will have risk to damage your Memory and Motherboard. 2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. 2. Remove your computer's cover and the bracket plate on the slot you intend to use. 3. Align the card's connectors and press firmly. 4. Secure the card on the slot with the screen you remove above. 5. Replace the computer system's cover. 6. Set up the BIOS if necessary. 7. Install the necessary software driver for your expansion card. 2-5-2 Assigning IRQs For Expansion Card 10 Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use. Standard Interrupt Assignments IRQ 0 1 2 3* 4* 5* 6* 7* 8 9* 10 * 11 * 12 * 13 14 * 15 * Priority N/A N/A N/A 8 9 6 11 7 N/A 10 3 2 4 N/A 5 1 Standard function System Timer Keyboard Controller Programmable Interrupt Communications Port (COM2) Communications Port (COM1) Sound Card (sometimes LPT2) Floppy Disk Controller Printer Port (LPT1) System CMOS/Real Time Clock ACPI Mode when enabled IRQ Holder for PCI Steering IRQ Holder for PCI Steering PS/2 Compatible Mouse Port Numeric Data Processor Primary IDE Channel Secondary IDE Channel * These IRQs are usually available for ISA or PCI devices. 2-5-3 Interrupt Request Table For This Motherboard Interrupt request are shared as shown the table below: INT A INT B INT C INT D INT E Slot 1 Slot 2 Slot 3 Slot4 Slot5 Onboard USB 1 Onboard USB 2 AC97/MC97 INT F INT G INT H IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support "Shared IRQ" or that the cards don't need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable. 2-5-4 AGP Slot This motherboard provides an AGP Slot, support the 2X/4X AGP VGA card. 11 2x notch AG SLO P T 4x notch 2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (20-pin block) : ATXPWR ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed. Press this switch again will turn off the power to the system board. Pin 1 PIN ROW2 ROW1 1 2 3 4 5 6 7 8 9 10 3.3V -12V GND Soft Power On GND GND GND -5V +5V +5V 3.3V 3.3V GND 5V GND 5V GND Power OK +5V (for Soft Logic) +12V (2) ATX 12V Power Connector (4-pin block) : ATX12V This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. Pin 1 12 (3) ATX P6 Power Connector (6-pin block) : ATXP9 This is a new defined 6-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 3.3V and 5V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. RED ORG ORG BLK BLK BLK 3.3V GND GND Power Connector on Motherboard GND 3.3V 5V Power Plugs from Power Supply (4) (5) (6) (7) (8) PS/2 Mouse & PS/2 Keyboard Connector: PS2KBM The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: CN1 The connectors are 4-pin connector that connect USB devices to the system board. Parallel Port Connector (25-pin female): COM_LP Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The Onboard Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. Audio and Game Connector : AUDIO_GAME This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin D-Subminiature Receptacle Connector for joystick/MIDI Device. Audio output to speaker Line-out : Audio input to sound chip Line-in : Microphone Connector MIC : Game/MIDI : For joystick or MIDI Device Serial Port COM1, COM2 : COM1, COM2 COM1, COM2 are the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled through BIOS SETUP. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. PS/2 Mouse PRINT GAME/MIDI PORT PS/2 USB COM1 COM2 Keyboard MIC LINE-IN LINE-OUT 13 (9) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. Pin 1 Primary IDE Connector (11) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. Secondary IDE Connector Pin 1 14 · · Two hard disks can be connected to each connector. The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. 2-6-2 Headers (1) Line-Out/MIC Header for Front Panel (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. Without install the cable, this header default setting is 5-6 short, 9-10 short. When you install the cable you have take off these jumpers. AUDIO AUD_MIC AUD_MIC_BIAS AUD_FPO _R UT HP_O N AUD_FPO _L UT Pin 1 2 AUD_G ND AUD_VC C AUD_RET_R AUD_R _L ET 9 10 Line-Out, MIC Headers (3) USB1.1 Port Headers (9-pin): USB1, USB2.0 Port Headers (9-pin): USB3 (for P4XFBU only) These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. +DATA G ND O C +DATA G ND O C +DATA G ND -DATA Pin 1 Pin 1 +DATA G ND -DATA USB2.0 Port Headers (for P4X533U only) USB1.1 Port Headers (4) IDE Activity LED: HD-LED This connector connects to the hard disk activity indicator light on the case. 15 -DATA VC C VC C -DATA VC C VC C USB3 USB1 (5) (6) (7) (8) Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. See the figure below. Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. See the figure below. Power LED: PWR-LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. Power switch: PWR-BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. Pin 1 JW_FP1 SPKR NC G ND VC C5 HDLED RE T SE SPEAK Pin 1 VC 5 C HDDL D E G ND RSTSW NC VC C5 AC D PILE PWR BTN G ND PWR-LED PWR-BTN System Case Connections (9) Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled. WOL 1 3 Wake-On-LAN Headers 16 5VSB G ND WO L (10) FAN Headers (3-pin) : SFAN1, SYSFAN, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of connector. CPUFAN 3 1 SYSFAN 1 3 3 SFAN1 1 FAN Speed Headers (11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. IR NC VC C5 IRTX Pin 1 2 G ND IRRX 5 6 IR infrared module Headers (12) CD Audio-In Headers (4-pin) : CD_IN CD_IN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. C -IN D 4 1 CD Audio-In Headers 17 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. 4. Turn on your peripheral as following order: a. Your monitor. b. Other external peripheral (Printer, Scanner, External Modem etc...) c. Your system power. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. 5. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. The system will then run power-on test. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen. If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance. Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM install or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency 6. During power-on, press key to enter BIOS setup. Follow the instructions in BIOS SETUP. 7. Power off your computer: You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. If you use Windows 9X, click "Start" button, click "Shut down" and then click "Shut down the computer?" The power supply should turn off after windows shut down. 18 Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best. In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: · · · · Press to quit the BIOS Setup. Press (up, down, left, right) to choose, in the main menu, the option you want to confirm or to modify. Press when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu. Press Page Up/Page Down or +/­ keys when you want to modify the BIOS parameters for the active option. 3-1 Entering Setup Power on the computer and by pressing immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing , and keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press to continue, or to enter Setup 3-2 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press . 19 3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press to accept or enter the sub-menu. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc : Quit F10 : Save & Exit Setup Miscellaneous Control Load optimized Defaults Load Standard Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item Time, Date, Hard Disk Type... Figure 3-1 Standard CMOS Features Use this Menu for basic system configurations. Advanced BIOS Features Use this menu to set the Advanced Features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system's performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management Setup Use this menu to specify your settings for power management. PnP/PCI configurations This entry appears if your system supports PnP/PCI. PC Health Status This entry shows your PC health status. Miscellaneous Control Use this menu to specify your settings for Miscellaneous control. 20 Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. 3-4 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) > > > > IDE IDE IDE IDE Primary Master Primary Slave Secondary Master Secondary Slave Thu, Sep, 12 2002 16 : 48 : 35 Press Press Press Press Enter Enter Enter Enter None None None None Item Help Menu Level > Change the day, month, year and century Drive A Drive B Video Halt On Base Memory Extended Memory Total Memory 1.44M, 3.25 in. None EGA/VGA All,But Keyboard 640K 56320K 57344K Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Optimized Defaults F1:General Help F7:Standard Defaults Date The date format is . Day of the week, from Sun to Sat, determined by BIOS. Read-only. Day Month The month from Jan. through Dec. The date from 1 to 31 can be keyed by numeric function keys. Date The year depends on the year of the BIOS. Year Time 21 The time format is . Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<­> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually. If you select Manual, related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer. If the controller of HDD interface is SCSI, the selection shall be "None". If the controller of HDD interface is CD-ROM, the selection shall be "None" The settings are Auto Normal, Large, and LBA. Access Mode number of cylinders Cylinder number of heads Head write precomp Precomp Landing Zone landing zone number of sectors Sector 3-5 Advanced BIOS Features CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Advanced BIOS Features Anti-Virus Protection CPU L1 Cache CPU L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot other Device Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Typematic Rate Setting Typematic Rate (Chars/Sec) Typematic Delay (Msec) Security Option OS Select For DRAM > 64MB HDD S.M.A.R.T. Capability Report No FDD For Windows Video BIOS Shadow Disabled Enabled Enabled Enabled Floppy HDD-0 CDROM Enabled Disabled Enabled On Disabled 6 250 Setup Non-OS2 Disabled Yes Enabled Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Anti-Virus Protection 22 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table. Activates automatically when the system boots up causing a warning Enabled message to appear when anything attempts to access the boot sector of hard disk partition table. CPU Internal Cache The default value is Enabled. Enabled (default) Enable cache Disable cache Disabled Note: The internal cache is built in the processor. External Cache Choose Enabled or Disabled. This option enables the Level 2 cache memory. CPU L2 Cache ECC Checking Choose Enabled or Disabled. This option enables the Level 2 cache memory ECC (error check correction). Quick Power On Self-Test This category speeds up Power On Self Test (POST) after you power on the computer. If this is set to Enabled. BIOS will shorten or skip some check items during POST. Enabled (default) Enable quick POST Normal POST Disabled First/Second/Third/Fourth Boot Device The BIOS attempts to load the operating system from the devices in the sequence selected in these items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAD and Disabled. Swap Floppy Drive Switches the floppy disk drives between being designated as A and B. Default is Disabled. Boot Up Floppy Seek During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks. Boot Up NumLock Status The default value is On. On (default) Keypad is numeric keys. Keypad is arrow keys. Off Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) 23 Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000. Security Option This category allows you to limit access to the system and Setup, or just to Setup. The system will not boot and access to Setup will be denied if the System correct password is not entered at the prompt. Setup (default) The system will boot, but access to Setup will be denied if the correct password is not entered prompt. OS Select For DRAM > 64MB Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2. Set to OS/2 if using more than 64MB and running OS/2. 3-6 Advanced Chipset Features The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Advanced Chipset Features > DRAM Timing Settings > AGP Timing Settings > PCI Timing Settings System BIOS Cacheable Video RAM Cacheable Memory Hole Press Enter Press Enter Press Enter Disabled Disabled Disabled Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults DRAM Timing Settings Please refer to section 3-6-1 AGP Timing Settings Please refer to section 3-6-2 PCI Timing Settings Please refer to section 3-6-3 System BIOS Cacheable 24 Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Video RAM Cacheable Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Memory Hole You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements. The settings are: Enabled and Disabled. 3-6-1 DRAM Timing Settings CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software DRAM Timing Settings Auto Configuration RAS Active Time RAS Precharge Time RAS to CAS Delay CAS Latency Bank Interleave DRAM Command Rate Standard 6T 3T 3T 2.5T Disabled 2T Command Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults RAS Active Time This field let's you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: 2T and 3T. RAS Precharge Time If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: 2T and 3T. CAS Latency When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The settings are: 2T and 2.5T. 3-6-2 AGP Timing Settings 25 CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software AGP Timing Settings AGP AGP AGP * AGP AGP AGP AGP CPU AGP Transfer Aperture Size Mode Driving Control Driving Value Fast Write Master 1 WS Write Master 1 WS Read to AGP Post Write Delay Transaction 64M Auto Auto DA Disabled Enabled Enabled Disabled Disabled Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Note: Change these settings only if you are familiar with the chipset. 3-6-3 PCI Timing Settings CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software PCI Timing Settings PCI PCI CPU PCI Master 1 WS Write Master 1 WS Read to PCI Write Buffer Delay Transaction Disabled Disabled Enabled Disabled Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The settings are: Enabled and Disabled. 3-7 Integrated Peripherals CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Integrated Peripherals > OnChip IDE Function > OnChip Device Function > Onboard Super IO Function Init Display First Press Enter Press Enter Press Enter PCI Slot Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults OnChip IDE Function 26 Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2 Onboard Super IO Function Please refer to section 3-7-3 Init Display First This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings are: PCI Slot, AGP Slot. 3-7-1 OnChip IDE Function CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software OnChip IDE Function OnChip IDE Channel0 OnChip IDE Channel1 Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE 32-bit Transfer Mode IDE HDD Block Mode IDE Prefetch Mode Delay For HDD (Secs) Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto Enabled Enabled Enabled 0 Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4. Primary/Secondary Master/Slave UDMA Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/33 and Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled. IDE HDD Block Mode 27 Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. The settings are: Enabled, Disabled. 3-7-2 OnChip Device Function CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software OnChip Device Function AC97 Sound Device Game Port Address Midi Port Address Midi Port IRQ AC97 Modem Device USB Host Controller USB Keyboard Legacy Support Auto 201 Disabled 10 Auto Enabled Disabled Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults AC97 Sound Device This item allows you to decide to enable/disable the chipset family to support AC97 Audio. The settings are: Enabled, Disabled. Game Port Address/Midi Port Address This will determine which Address the Game Port/Midi Port will use. AC97 Modem Device This item allows you to decide to enable/disable the chipset family to support AC97 Modem. The settings are: Auto, Disabled. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled. USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The settings are: Enabled, Disabled. 3-7-3 Onboard Super IO Function 28 CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Onboard Super IO Function Onboard FDD Controller Onboard Serial Port 1 Onboard Serial Port 2 UART2 Mode RxD, TxD Active IR Duplex Mode Use IR Pins Onboard Parallel Port Parallel Mode EPP Mode Select ECP Mode Use DMA Enabled 3F8/IRQ4 2F8/IRQ3 Normal Hi, Lo Half IRRX/IRTX 378/IRQ7 SPP EPP1.7 3 Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Onboard FDD Controller Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and you wish to use it. If you install add-on FDC or the system has no floppy drive, select Disabled in this field. The settings are: Enabled and Disabled. Onboard Serial Port 1/Port 2 Select an address and corresponding interrupt for the first and the second serial ports. The settings are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto. UART2 Mode This item allows you to determine which InfraRed(IR) function of the onboard I/O chip, this functions uses. Onboard Parallel Port There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP, and EPP features. It has the following option: Disabled Line Printer port 0 (3BCH/IRQ7)/ Line Printer port 2 (278H/IRQ5)/ Line Printer port 1 (378H/IRQ7) Parallel Port Mode SPP : Standard Parallel Port EPP : Enhanced Parallel Port ECP : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose "SPP." To operate the onboard parallel port in the EPP modes simultaneously, choose "EPP." By choosing "ECP", the onboard parallel port will operate in ECP mode only. Choosing "ECP+EPP" will allow the onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After selecting it, the following message will appear: "ECP Mode Use DMA" at this time, the user can choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so after the user chooses the onboard parallel port with the EPP function, the following message will be displayed on the screen: "EPP Mode Select." At this time either EPP 1.7 spec. or EPP 1.9 spec. can be chosen. 3-8 Power Management Setup 29 The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Power Management Setup ACPI Function Video Off Option Video off Method MODEM Use IRQ Power Button Function Power After Power Failure > Wake Up Events Enabled Always off V/H SYNC+Blank 3 Instant-Off Off Press Enter Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults ACPI Function This item allows you to Enabled/Disabled the Advanced Configuration and Power Management (ACPI). The settings are Enabled and Disabled. Video Off Option This determines the manner in which the monitor is blanked. The choice are Suspend off, All Modes Off, and Always On. Video Off Method This determines the manner in which the monitor is blanked. Initial display power management signaling. DPMS (default) This option only writes blanks to the video buffer. Blank Screen V/H SYNC+Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off. Wake Up Events Please refer to section 3-8-1 3-8-1 Wake up Events 30 CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Wake Up Events VGA LPT & COM HDD & FDD PCI Master Wake-Up on Ring/LAN Wake-Up on PCI PME Wake-Up on RTC Alarm x Date of Month Alarm x Time (hh:mm:ss) Alarm > IRQs Activities OFF LPT/COM ON OFF Disabled Disabled Disabled 0 0:0:0 Press Enter Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Wake Up On Ring/PME During Disabled, the system will ignore any incoming call from the modem. During Enabled, the system will boot up if there's an incoming call from the modem. Wake-Up on RTC Alarm This function is for setting date and time for your computer to boot up. During Disabled, you cannot use this function. During Enabled, choose the Date and Time Alarm: Date(of month) Alarm You can choose which month the system will boot up. Set to 0, to boot every day. Time(hh:mm:ss) Alarm You can choose what hour, minute and second the system will boot up. Note: If you have change the setting, you must let the system boot up until it goes to the operating system, before this function will work. IRQs Activities Please refer to section 3-8-1.1 3-8-1.1 IRQs Activities CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software IRQs Activities Primary INTR ON Item Help IRQ3 (COM 2) Enabled IRQ4 (COM 1) Enabled IRQ5 (LPT 2) Enabled Menu Level >>> IRQ6 (Floppy Disk) Enabled IRQ7 (LPT 1) Enabled IRQ8 (RTC Alarm) Disabled IRQ9 (IRQ2 Redir) Disabled IRQ10 (Reserved) Disabled IRQ11 (Reserved) Disabled IRQ12 (PS/2 Mouse) Enabled IRQ13 (Coprocessor) Disabled IRQ14 (Hard Disk) Enabled IRQ15 (Reserved) Disabled Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults 3-9 PnP/PCI Configuration Setup 31 This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software PnP/PCI Configurations PnP OS Installed Reset Configuration Data Resources Controlled By x IRQ Resources PCI/VGA Palette Snoop Assign IRQ For VGA Assign IRQ For USB No Disabled Manual Press Enter Disabled Enabled Enabled Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Reset Configuration Data Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system can not boot. The settings are: Enabled and Disabled. Resource Controlled By The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows95/98. If you set this field to "manual" choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a ">"). The settings are: Auto(ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-9-1 IRQ Resources 32 CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software IRQ Resources IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 assigned assigned assigned assigned assigned assigned assigned assigned assigned assigned to to to to to to to to to to PCI PCI PCI PCI PCI PCI PCI PCI PCI PCI Device Device Device Device Device Device Device Device Device Device Item Help Menu Level >> Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults 3-10 PC Health Status This section shows the Status of you CPU, Fan, Warning for overall system status. This is only available if there is Hardware Monitor onboard. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software PC Health Status Shutdown Temperature CPU Warning Temperature Show PC Health in Post Current System Temperature Current CPU Temperature CPUFAN SYSFAN Vcore Vcc3.3 + 5V +12V -12V -5V VBAT(V) 5VSB(V) Disabled Disabled Enabled 25°C 38°C 5000 rpm 5000 rpm 1.78V 3.31V 4.98V 12.22V -12.36V -5.09V 3.21V 5.02V Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Shutdown Temperature This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed. Detect CPUFAN in Post During Enabled, system will warn the user if CPU Fan is not functioning. 3-11 Miscellaneous Control 33 This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility ­ Copyright(C) 1984-2002 Award Software Miscellaneous Control CPU Clock Ratio 8X Auto Detect DIMM/PCI Clk Enabled Spread Spectrum Disabled ** Current Host/PCI Clock is 100/33MHz ** Host/PCI Clock at Next Boot is 100/33MHz ** Current DRAM Clock is 133MHz ** DRAM Clock at next Boot is 133MHz AGP VddQ Select 1.5V (Default) VDIMM Select Default Item Help Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Optimized Defaults F1:General Help F7:Standard Defaults Auto Detect DIMM/PCI Clk This item allows you to enable/disable auto detect DIMM/PCI Clock. Spread Spectrum This item allows you to set the CPU Host/PCI clock and Spread Spectrum. The settings are: Enabled, Disabled. Host/PCI Clock at next Boot is This item allows you to select CPU frequency step by step increasing The choice are: 100MHz132MHz, 133MHz200MHz. DRAM Clock at next Boot is This field displays the capability of the memory modules that you can use The choice is either 100MHz or 133MHz (only select CPU Frequency 100MHz.) AGP VddQ Select This item allows you to select 1.5V of the AGP 4X VGA card. The choice are: 1.5V, 1.6V. VDIMM Select This item allows you to select 2.5V of the DDR Module. The choice are: 2.5V, 2.6V 3-12 Load Standard/Optimized Defaults 34 Load Standard Defaults When you press on this item, you get confirmation dialog box with a message similar to: Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press on this item, you get a confirmation dialog box with a message similar to: Load Optimized Defaults (Y/N)? N Pressing loads the default values that are factory settings for optimal performance system operations. 3-13 Set Supervisor/User Password You can set either supervisor or user password, or both of them. The differences are: Can enter and change the options of the setup menus. Can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press . The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press . You may also press to abort the selection and not enter a password. To disable a password, just press when you are prompted to enter the password. A message will confirm that the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely. PASSWORD DISABLED. When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer. You determine when the password is required within the BIOS Features Setup Menu and its Security option. If the Security option is set to "System", the password will be required both at boot and at entry to Setup. If set to "Setup", prompting only occurs when trying to enter Setup. Supervisor password: User password: Chapter 4 35 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL supports WINDOWS 9X/ME/NT4.0/2000/XP Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive). From MAGIC INSTALL MENU you may make 9 selections: 1. VIA 4 IN 1 install VIA Service Pack 4 IN 1 driver 2. SOUND install AC97 Audio Codec Installing driver 3. USB2.0 install USB 2.0 driver (Only for P4XFBU) 4. PC-HEALTH install Winbond PC-HEALTH hardware monitor Software 5. MAGIC BIOS install BIOS Live Update Utility 6. PC-CILLIN install PC-CILLIN2002 anti-virus program 7. DIRECTX8 install Microsoft DirectX 8.0 driver 8. BROWSE CD to browse the contents of the CD 9. EXIT to exit from MAGIC INSTALL menu 4-1 IDE Install VIA Service Pack 4 IN 1 Driver * The path of the file is X:\VIA\DRIVER\SETUP.EXE 36 IDE : AGPVXD : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS ONLY, IT WILL FIX PCI IRQ ROUTING SEQUENCE IRQ ROUTING : VIA PCI IRQ MINIPORT DRIVER IS TO BE INSTALLED UNDER WIN98 INF : VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS THE DRIVER WILL ENABLE VIA POWER MANAGERMENT CONTROLLER 1. Click IDE when MAGIC INSTALL MENU appears 2. Click NEXT when VIA Service Pack Wizard appears 3. This is to announce the Copy Write, click Yes 4. Click NEXT to choose all driver 37 5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 38 4-2 Sound Install ALC Audio Codec Driver 1. Click SOUND when MAGIC INSTALL MENU appears 2. Then auto detect operation system language edition, click OK, start to install DRIVER 3. Click Finish and Restart Windows 4. Click StartProgramAvance Sound ManagerAvRack. Then AVRACK Windows appears 5. Sound Effect select and KaraOK Mode 6. Manual Sound Effect Setting Function Note: The path of the file For WIN98/NT4.0/WIN2K is X:\CODEC\ALCCODEC\SETUP.EXE For WIN95 is X:\VIA\VIAUDIO\SETUP.EXE For Linux is X:\VIA\VIAUDIO\Linux For Real DOS Mode is X:\VIA\VIAUDIO\VIADOS 39 4-3 USB2.0 Install VIA USB2.0 Device Driver (Only for P4XFBU) 1. Click USB2.0 when MAGIC INSTALL MENU Appear 2. When USB2.0 Setup Program Appear, Click NEXT 3. Select Install USB Driver and Click NEXT 4. Select FINISH and Restart your Computer 5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE 40 4-4 PC-HEALTH Winbond Hardware Doctor Monitoring Software The path of the file is X:\VIA\HEALTH-W\SETUP.EXE (Support Windows 9X/ME/2K/NT/XP) In Windows 95/98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that's why it needs install PC-HEALTH twice to complete setup. 1. Click PC-Health when Magic Install Menu appears