User manual JOHN LEWIS JLBIHD601

JLBIHD601 - JLBIHD902 built-in cooker hood Instruction manual Important Safety Information It is most important that this instruction manual should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings ha ve been pr ovided in the inter est of saf ety .You MUST read them carefully before use or installation by a qualified person. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. Installation · Any installation work must be undertaken by a qualified and competent person to the relevant National Standards. · This hood must be installed in accordance with the installation instructions and all measurements must be adhered to. · If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS.6172, BS.5440 and BS.6891 (Natural Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation & Use) Regulations, the Building Regulations issued by the Department of the Environment, the Building standards (Scotland) (Consolidated) Regulations issued by the Scottish Development Department. · The fan motor of this cooker hood incorporates a cut-out device which will operate if the cooker hood is installed below the minimum height recommended under section `Clearance Height', or if the motor becomes overheated. If the cut-out device is activated, switch off the fan motor and allow the cooker hood to cool. The cut-out device will reset itself when the fan motor has cooled significantly. · It is dangerous to alter the specifications or modify this product in any way. · When installed between adjoining wall cabinets the wall cabinets must not overhang the hob. · If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. · If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. · Do not install above a cooker with a high level grill. Use · This product is for domestic use only. · Never leave frying pans unattended during use as overheated fats and oils might catch fire. · Never do flambé cooking under this cooker hood. · Do not leave naked flames under the hood. · This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Maintenance and Cleaning · This appliance can be a hazard if the synthetic paper and charcoal filters are not replaced as recommended. Service · Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunction. Refer to your local Service Force Centre. Always insist on genuine spare parts. Environmental Information · After installation please dispose of the packaging with due regard to safety and the environment. · The symbol on the product or on its packaging indicates that this product should not be treated as normal household waste. Instead it shall be handed over to an approved collection facility for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Child Safety · This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. 2 Contents For the User Important Safety Information Description of the Appliance Using the cooker hood Cooker Hood Controls To Operate Recirculation Extraction For the Installer 2 4 10 10 10 10 10 Electrical Connections Electrical Requirements Electrical Connection 9 9 9 Installing the Cooker Hood Installation Requirements Unpacking Fitting the Wall Brackets Fitting the Canopy Hood Extraction Recirculation Fitting the Chimney Stack 5 5 5 6 6 7 7 8 Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove/Replace Charcoal Filter Changing the Light Bulb 11 11 11 12 12 12 Something Not Working Repairs and After Sales Service 13 13 Guide to use the Instruction Manual The following symbols will be found in the text to guide you through the instruction book Safety instructions Step by step instructions Environmental Information This appliance complies with the followings E.E.C. Directives: - 89/336 (Electromagnetic Compatibility Directive) - 73/23 (Low Voltage Directive) - 93/68 (General Directives) and subsequent modifications 3 Description of the Appliance 240 18 min. 560 560 max. 765 100 598 - 698 - 898 210 150 490 205 650 min. 4 Installation Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas. The chimney hood must be installed according to the instructions suppliers below and by qualified and competent personnel to the relevant National Standards. This cooker hood is designed to be fixed to any vertical surface over a cooking area, and can be used in the extraction (ducted to the outside) or recirculation mode. The installation work must be undertaken by a qualified and competent person. The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation. 15 7.2.1 12c Unpacking Before unpacking the cooker hood position the carton with the arrows pointing upwards as illustrated on the carton. The cooker hood is made up of the following components: Ref Qty Product Components 1 1 Hood body, complete with controls, lighting, fan and filters. 2 1 Telescopic Chimney comprising: 2.1 1 Upper section 2.2 1 Lower section 9 1 ø150-120 Ducting spigot 10 1 ø120-125 Ducting flange 15 1 Air outlet connector Ref Qty 7.1 2 7.2.1 2 12c 6 12d 2 Ref Qty 1 Installation Components Hood body fixing brackets Upper chimney wall fixing brackets Chimney fixing screws Screws M4x25 Documentation Instruction booklet 2.1 2 2.2 10 9 12c 12c 7.1 1 12d 5 Installing the Cooker Hood Fitting the Wall Brackets · Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. · Draw a horizontal line at 650 mm above the hob for installation without the back panel, or at height H (H=height of the visible part of the panel) for installation with the back panel. · Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. · Mark the wall at the centres of the holes in the bracket. · Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. · Mark the wall at the centres of the holes in the bracket. · Place bracket 7.1 as shown 95 mm from the vertical reference line and 210 mm above the horizontal reference line. · Mark the centres of the holes in the bracket. · Repeat this operation on the other side. 650 min. Splashback (Optional) The Splashback must be fitted before fixing the hood body and, if it is to be fixed at both top and bottom, must be fitted at the correct height prior to installing the bases. As this operation is rather complex, it should be carried out either by the kitchen installer or a qualified person who knows the final dimensions of the units. For fixing at the top only, proceed as follows: · Rest the back panel on the base, inserting the lower plate between the upper surface and the wall, centring it on the vertical reference line. · Mark the centres of the two holes in the upper plate. · Drill ø 8 mm holes at all the centre points marked. · Insert the wall plugs (not supplied) in the holes. · Fix the brackets using the screws (not supplied). · Fix the back panel (where present) using the screws (not supplied). Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then special fixing screws will be required (not supplied). 12.d Fitting the Canopy Hood · Screw the two screws item 12d supplied onto the brackets 7.1. · Hook the hood body onto the bracket 7.1, centring it around the vertical line. · Use the adjusting screws item 12d underneath the hood to level the hood body 7.1 H 210 7.1 95 95 X 7.2.1 1÷2 6 Extraction (Ducted) The cooker hood is more effective when installed in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be evacuated through an outside vent of ø125 (5ins) or ø150mm (6ins). The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102-B1. When the cooker hood is ducted to the outside the charcoal filter must be removed. Fitting the Ducting · Fit the ø150mm (6ins) ducting to the spigot on top of the hood body as illustrated. · When using ø125mm (5ins) ducting fit item 9 and 10 on to the spigot on the top of the hood body as illustrated. · For the best performance use the shortest possible run of ducting and we recommend the use of rigid pipe in preference to flexible hose as this will improve the flow of air while reducing turbulence, which causes noise and a loss of performance. · If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler, then its flue must be be of the room sealed or balanced flue type. · If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The cooker ducting when fitted in the extraction mode must never be connected to central heating flues, radiators or water heaters. ø 150 ø 125 9 10 Recirculation Mode The cooker hood is supplied specified for use in the recirculation mode, with the charcoal filter fitted. In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney. · Push fit the air outlet connector item 15 onto the air outlet. · Ensure the activated charcoal filter has been fitted. 15 7 12c Fitting the Upper Chimney · Slightly widen the two sides of the upper chimney and hook them behind the brackets item 7.2.1 ensuring they are correctly seated. · Secure the sides to the brackets using the 4 screws item 12c (2.9 x 9.5mm) supplied. 2.2 2 2.1 12c Fitting the Lower Chimney · Slightly widen the two sides of the lower chimney and hook them between the upper chimney and the wall, ensuring they are correctly seated. · Fix the lower chimney to the hood body using 2 screws item 12c (2.9 x 9.5mm) supplied. · Make sure that the air outlet connection is aligned with the chimney outlets. 12c 8 Electrical Connections DOUBLE INSULATED DO NOT EARTH Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. 9 Using the cooker hood The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air. Cooker Hood Controls The cooker hood functions are controlled by four push button switches located centrally in the control fascia. L S V1 Turns the worktop lighting On and Off Mains light - illumination indicates fan motor is running Motor ON/OFF switch. Depress to turn the extractor motor on at a LOW speed, to ensure that light cooking vapours are silently extracted. Medium speed, suitable for general use. This speed provides an optimum treated air flow to noise level ratio. Maximum speed, used to extract intensive levels of cooking vapour emissions. S V1 V2 V3 L V2 V3 To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters. The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack. Extraction In the extraction mode the contaminated air enters the cooker hood passing through the grease filters and is passed out through the ducting into the atmosphere. To obtain the best performance when cooking it is advisable to switch the cooker hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing. When used in the ducting mode the charcoal filters are not required. Never do flambé cooking under this cooker hood. Never leave frying pans unattended during use, as over-heated fats and oils can catch fire. Do not leave naked flames under the cooker hood. Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously. 10 Maintenance and Cleaning Before carrying out any maintenance or leaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel. Metal Grease Filters The grease filters absorb grease and dust during cooking to help keep the cooker hood clean inside, and should be cleaned approximately once every month or more often if the hood is used for more than 3 hours a day. Remove the metal grease filters one at a time by: Releasing the catches on the filters, the filters can be removed. The metal grease filters should be washed, by hand, in mild soapy water or in a dishwasher. Allow to dry completely before replacing. 11 Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. To Remove/Replace the Charcoal Filters 1. First remove the metal grease filters. 2. Rotate the charcoal filter anti-clockwise (A) and remove. 3. To replace the charcoal filters, remove the metal grease filters. 4. Place the filter over the inlet grille at either end of the fan housing and rotate clockwise (B) into position. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. B A Changing the Light Bulb Remove the screw fastening the lamp cover. Pull the lamp cover downwards. Rotate the light bulb anti-clockwise to unscrew. To replace the light bulb insert a replacement into the holder then rotate the bulb clockwise into position. Ensure you take care not to overtighten the bulb. 5. Replace the lamp cover. If the light bulb fails to function check that the bulb is fully screwed into the holder. If bulb failure has occurred then it should be replaced with a 220-240 Volt 40W clear globe shaped bulb with a small E14 screw thread. Replacement filters and light bulbs can be obtained from your local Service Force Centre. 1. 2. 3. 4. 12 Something not Working If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Force agent. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · Make sure the switch is in the `ON' position. The cooker hood is not working effectively · Check that the fan speed is set high enough for the task · Ensure the grease filter is clean. · Ensure the kitchen is adequately vented to allow the entry of fresh air. · If set up for recirculation, check that the charcoal filter is still effective. · If set up for extraction, check that the ducting and outlets are not blocked. · The safety cut-out device has been tripped. · Tum off the hob and then wait for the device to reset. The cooker hood has switched off during operation Repairs and After Sales Service In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact our extended warranty administrators by telephoning: When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of fault 4. The model and serial number of the appliance (found on the rating plate - see picture) 0870 01 07887 They will give you details for your local Service Force Centre. Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working". Your oven is covered by a 3 year parts and labour guarantee (see separate details given at point of sale). Please retain your purchase receipt safely for the service engineer to verify the purchase details. 5. The purchase date. Please note that a valid purchase receipt is required for in-guarantee service calls. 13 John Lewis Partnership 171 Victoria Street London SW1E 5NN www.johnlewis.com 436002885_02 - 060227 0306