User manual JOHN LEWIS JLBIWD1400

JLBIWD 1400 Built-in 1400 spin washer-dryer Instruction manual On/Off 1400 900 700 500 Extra dry Store dry Iron dry Programme time Prewash Wash Rinse Rinse hold Drain Spin Drying Spin Drain Softeners Rinse Soak 30° Cold 30° 40° Delicates 30° Delicates 40° Economy 60° 60° Economy 40° 40° 30° Drying Economy 40° 40° Easy iron 40° Drying 60° Rinse hold Spin Prewash Quick Extra Automatic Time rinse dry dry Delay start Start/ Pause Wool End JLBIWD1400 Synthetics Cottons 30 Minute wash Off 90° Important Safety Information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings have been provided in the interest of safety. You MUST read them carefully before use or installation by a qualified person. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. Installation This appliance is heavy. Care should be taken when moving it. It is dangerous to alter the specifications or attempt to modify this product in any way. All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in instructions. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely. Child Safety This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product. Pets and children have been known to climb into washer-dryers. Please check your drum before use. The glass door becomes very hot during the washing cycle. Keep children away from the vicinity of the appliance whilst it is in operation. Keep all packaging well away from children. Keep all detergents in a safe place out of children's reach. Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine. Garments which have been in contact with volatile petroleum products should not be machine washed. If volatile cleaning fluids are used, care should be taken to ensure that the fluid is removed from the garment before placing in the machine. Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum. Only use the advised quantities of fabric softener. Damage to the fabric can ensue if you over-fill. Refer to the manufacturer's recommendations of quantities. As some duvets and eiderdowns should be washed/dried in large commercial machines because of their bulk, please check with the manufacturer of the item before washing in a domestic machine. The users should always check that they have not left their gas lighters (disposable or otherwise) in their clothing. Never tumble dry items that have had contact with chemicals such as dry cleaning fluid.These are of a volatile nature and could cause an explosion. Only tumble dry items which have been washed in water or require airing. Use Maintenance and Cleaning Always unplug the appliance and turn off the water supply after use. Do not overload the appliance. See relevant section in the instruction book. Only wash and dry fabrics which are designed to be machine washed and dried. If in doubt, consult the care label on the clothes. Before washing, ensure that all pockets are empty and buttons and zips are fastened. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass before washing. Underwired bras must NOT be machine washed. Plastic detergent dispensers should not remain in the drum during the drying cycle, as the plastic used is not designed to withstand the heat. If you wish to washthrough-to-dry you should use the conventional detergent dispenser drawer. Leave the porthole door slightly ajar between washes to preserve the door seal. Service Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Force Centre. Always insist on genuine spare parts. 2 Contents Important Safety Information Your New Washer-Dryer Description of the Appliance Detergent dispenser drawer Child safety feature 2 4 5 5 5 For the Installer Installation Instructions Technical Specifications Unpacking Positioning Installation on a suspended floor Building-in Water inlet Water drainage Levelling Special conditions In the interest of the environment Electrical connection Permanent connection 6 6 7 7 7 8-10 10 11 12 12 12 12-13 13 Select the desired programme/temperature 20 Select the spin speed or the "Rinse hold" option 20 Select the desired options 20 Select the "Delay start" 20 Start the programme 20 How to change an option or a programme during its cycle 20 How to interrupt a programme 21 How to open the door during the cycle of a programme 21 End of programme 21 Drying 2.5 kg of cotton 22 Autodrying 1.5 kg of synthetics 22-23 Washing and Drying Wash Care Symbols Washing Programmes Drying Programmes Maintenance and Cleaning Descaling After each wash Maintenance Wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the filter Cleaning the water inlet filter The dangers of freezing Emergency emptying out 24 24 26-27 28 29-30 29 29 29 29 29 29 29-30 30 30 30 For the User The Control Panel Programme information Operating Sequence Load the laundry Measure out the detergent Measure out the fabric softener Switch the machine on 14-17 18 19-21 19 19 19 19 Something Not Working Service and Spare Parts 31-32 33 This appliance complies with the following E.E.C. Directives: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications. Guide to use the Instruction Book The following symbols will be found in the text to guide you throughout the instructions: Safety instructions Hints and tips Environmental information 3 Your New Washer-Dryer Your new washer-dryer, which is fitted with the Jet System, meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. Even small loads are washed "economically" because the amount of water used is regulated automatically according to the load and type of fabric. The programme progress display shows the programme steps selected, the programme phase which is running and the end of the programme. The programme selector dial combines the function of programme and temperature selection, making it easier to set the programme. Automatic cooling of the wash water to 60°C before draining, with the 90°C programme. This reduces thermal shock to fabrics, helping to prevent creasing. The special wool programme with its new delicate wash system treats your woollens with extreme care. The balance control device ensures that the washer-dryer remains stable when spinning. The two drying programmes will give your wash that soft, relaxed feel whatever the weather. Ecological hints To save water and energy and help protect the environment, we recommend that you follow these hints: Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). The machine works more economically if it is fully loaded. With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed. Try to load the maximum drying capacity of the machine as small loads are uneconomical. Save energy and reduce drying time by ensuring the laundry load has been thoroughly spun before attempting to machine dry. Environmental Information Materials marked with the symbol are recyclable. Check with your local Council or Environmental Health Office to see if there are facilities in your area for re-cycling this appliance. When the appliance is to be scrapped, cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside. Help to keep your country tidy - use authorised disposal sites for your old appliance. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Important Your machine is fitted with a balance control device, which ensures the machine is stable during the spin. If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the wash load manually and select a spin programme. For more detailed information see the section headed "Something Not Working" (See pages 31 to 32). 4 Description of the Appliance 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Filter 5 Adjustable feet On/Off 1400 900 700 500 Extra dry Store dry Iron dry Programme time Prewash Wash Rinse Rinse hold Drain Spin Drying Spin Drain Softeners Rinse Soak 30° Cold 30° 40° Delicates 30° Delicates 40° Economy 60° 60° Economy 40° 40° 30° Drying Economy 40° 40° Easy iron 40° Drying 60° Rinse hold Spin Prewash Quick Extra Automatic Time rinse dry dry Delay start Start/ Pause Wool End JLBIWD1400 Detergent dispenser drawer Prewash Main wash Fabric softener C0110 Child safety feature This machine incorporates a special child safety feature to prevent small children from being trapped inside the machine. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical. P1131 5 Synthetics Cottons 30 Minute wash Off 90° Installation Instructions It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. Technical Specifications DIMENSIONS Height Width Depth 82 cm 60 cm 54 cm 230-240 V/50 Hz 2050 W (10 A) Minimum Maximum Washing Cotton, linen Synthetics Delicate fabrics Wool/Hand wash Drying Cotton, linen Synthetics MaximumZ 16 S Energy Water 0.05 MPa (0.5 bar) 0.80 MPa (8. bar) 5.kg 2 kg 2.kg 1 kg 2.5.kg 1.5.kg 1400 rpm 0.85 kWh 49 litres POWER SUPPLY VOLTAGE TOTAL POWER ABSORBED WATER PRESSURE MAXIMUM RECOMMENDED LOAD SPIN SPEED CONSUMPTION DATA FOR WASHING 5 KG NORMALLY SOILED COTTON ITEMS WITH PROGRAMME " "Cottons Economy 60°" (White Cottons): 6 Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all the packaging for re-use in case the machine is to be transported again. Using a spanner unscrew and remove the rear right bolt. Lay the machine gently on its back, making sure that the hoses are not squashed. Set the machine upright and remove the two remaining bolts from the back. Pull out the three plastic spacers from the holes into which the bolts were fitted. Plug the open holes with the plugs supplied with the instruction booklet. P0256 P0020 P0255 Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Your new washer-dryer has been designed to be permanently plumbed in to your home's water supply and drainage system. However, if this is not possible, it may be connected to a suitable existing tap with the drain hose discharging into a sink. The appliance has an inlet hose, with female 3/4" BSP thread connector. If this connection is not compatible with the plumbing of the existing installation, a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing. Any alteration to your existing plumbing must be carried out by a competent person, or qualified plumber. Remove the polystyrene base and take off the bottom panel by unscrewing the central screw. Carefully slide out the right polythene bag. P0457 P0015 Repeat the operation for the left and central polythene bags. Re-fit the bottom panel using the 4 screws supplied with the door hinges (in the plastic bag) and the previously removed screw. Installation on a Suspended Floor P0016 P0453 Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor beams with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable. 7 Building-in This appliance has been designed to be built into the kitchen furniture. The recess should have the dimensions shown in picture A. 600 600 6 4 1 1 2 7 5 3 820 min 515 176,5 596 570 min. P0982 23 B 818 416 120 54 8 90 0 49 1 195 P0965 A When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped. Fig. AB. a) Door The dimensions of the door should be: - width 595-598 mm - thickness 16-22 mm The height (C-Fig. C) depends on the height of the adjacent furniture's base. 35 Ø 12.5-14 depth 16 -22 165 160 416 595598 B ,5 22+1 C P0422S C Preparation and assembly of the door The machine is originally pre-arranged for the assembly of a door opening from right to left. In this case it is sufficient to screw in the hinges (1) and the counter-magnet (6) provided with the appliance, at the right level (Fig. B). b) Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door. The distance between the holes hobs fixing centres must be 416 mm. The distance (B) from upper edge of the door to the centre of the hole depends on the adjacent furniture's dimensions. The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with the appliance. 8 c) Mounting the door Fix the hinges (1) to the machine by means of the M5x15 screws (3-Fig. B). The hinges can be adjusted to compensate for possible uneven thickness of the door. To align the door perfectly it is necessary to loosen the screw (3-Fig. B), adjust the door and tighten the screw again. d) Counter-magnet (6) The appliance is pre-arranged for a magnetic closure of the door. To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet (4) on the appliance (See fig. D). Recommendations regarding the construction and fitting of a base when the installation requires an integrated appliance to be raised Where the appliance has been raised by mounting onto a wooden base provided by the installer. The material used to construct the base should have a non slip surface, be water repellent and if possible be one solid piece. If it is not possible to use one solid piece, due to the additional height required, ensure that any additional strips of timber are glued and screwed to the underside of the base (see Fig. F). 5 mm Hardwood strip 6 4 40 mm 100 mm Additional pieces of timber should run from front to back 600-605 mm F P0984 Front view D If the door has to be opened from left to right, invert the position of the plates (7), the magnet (4) and the plate (5) (Fig. B and E). Mount the countermagnet (6) and the hinges (1) as previously described. Drill four fixing holes see Fig. G 600-605 mm 4 6 E 490 mm 5 7 1 95 mm 50 mm Front edge 3 P0983 G 2 Top view 9 Position the base into the recess with its front edge as far forward as the adjoining plinth line will allow. The reason for placing the base in this position is to allow a small strip of beading to be fitted in front of the appliance feet. Fix the base firmly to the floor using four appropriate countersunk screws (see Fig. H). Water inlet Connect the hose to a tap with a 3/4" thread. Always use the hose supplied with the appliance to connect to the water supply. Do not use previously used hoses for water connection. The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window "A". Should this occur, turn the water tap off and refer to your Service Centre to replace the hose. Hardwood strip 5 mm x 25 mm 5 X 25 X 605 490 600-605 H A P0352 With the appliance installed adjust all four feet ensuring the machine is stable, and a clearance of approximately 5 mm is left between the top of the machine and the underside of the worktop. A final check for stability should be carried out with the machine on spin with a load, this will identify the need for any further fine adjustment to the feet. A strip of beading approximately 605 mm W, x 5 mm H, x 25 mm D must be screwed down into the base directly in front of the machine's feet, this will provide additional security. If required an additional door magnet, part number 1242394-00/3 and disc, part number 1242393-00/5 are available from spare parts. Installation should comply with local water authority and building regulations' requirements. The appliance must be connected to a cold water supply. A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum distance of 5.02m (16.5 ft) between the appliance's inlet and the bottom of the water storage tank. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. P0021 10 Water drainage This appliance is designed to be permanently plumbed into your home's drainage system using one of the following methods. 1. Into a drainage standpipe. Firstly form a hook in the end of the drain hose using the "U" piece" supplied. If your drain hose looks like this (see below) you do not require the "U" piece". Just push the hose firmly into the standpipe. P1212 U piece supplied P1199 2. Onto a sink outlet spigot. If the outlet spigot has not been used before, remove any blanking plug that may be in place. Place the drain hose into your standpipe, which should have an internal diameter of approximately 38mm thus ensuring there is an air break between the drain hose and standpipe. 38 mm (11.2) standpipe diameter 30 cm (12") P1197 Push the drain hose onto the spigot and secure with a clip if required, ensure a loop is formed in the drain hose (see diagram) to prevent waste from the sink entering the washing machine. When discharging into a standpipe ensure that the top of the standpipe is no more than 90cm (35.4'') and no less than 60cm (23.6'') above floor level. 3 pin Loop P1198 Max. 90 cm (35.4) Min. 60 cm (23.6) Important Before connecting the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. P1039 The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter of 18 mm. 11 Levelling Level the washing machine by raising or lowering the feet. The feet may be tight to adjust as they incorporate a self locking nut, but the machine MUST be level and stable (check diagonally). In the interest of the environment Washing machines and dishwashers should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. SHOWER SINK BATH TOILET BIDET P1051 WASHING MACHINE DISHWASHER Any necessary adjustment can be made with a spanner. Accurate levelling prevents vibration, noise and displacement of the machine during operation. Some vibration is inevitable, especially if mounted on a wooden floor. Sprung wooden floors are particularly susceptible to vibration. For advice, consult a builder. If possible, always place the machine on a solid floor. RAINWATER 'RUN-OFF' FOUL DRAIN SURFACE WATER DRAINS & SEWERS FOUL SEWERS SEWAGE TREATMENT WORKS TREATED DISCHARGE RIVER RIVER UNTREATED DISCHARGE P0987 Special conditions If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine. Warning The machine should NOT be placed on deep pile carpeting. Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local water authority. Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance's rating plate. 12 The rating plate is located at the top of the rim of the open door. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. WARNING: A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. Should the appliance power supply cable neeed to be replaced, this must be carried out by our Service Force Centre. The power supply cable must be easily accessible after installing the appliance. Important If the mains supply cable is damaged it must be replaced; contact our warranty administrators on 0870 0107887 who will give you details for your local Service Force Centre. Mo Pro d. ..... d. No ..... . ..... ..... . Ser . No . ..... .... Mod. .......... Prod. No. ........... P0042 BD Ser. No. ......... The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS1363/A) fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live GREEN & YELLOW E 13 A Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point. N L BROWN BLUE P1041 CORD CLAMP The wire coloured green and yellow must be connected to the terminal marked with the letter «E» or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal marked «N» or coloured black. The wire coloured brown must be connected to the terminal marked «L» or coloured red. 13 The Control Panel On/Off 1400 900 700 500 Extra dry Store dry Iron dry Programme time Prewash Wash Rinse Rinse hold Drain Spin Drying End Wool Spin Drain Softeners Rinse Soak 30° Cold 30° 40° Delicates 30° Delicates 40° Off Economy 60° 60° Economy 40° 40° 30° Drying Economy 40° 40° Easy iron 40° Drying 60° Rinse hold Spin Prewash Quick Extra Automatic Time rinse dry dry Delay start Start/ Pause JLBIWD1400 1 23 4 5 6 7 8 9 11 1 0 12 1 Detergent dispenser drawer 2 Mains-on light This light comes on when the "On/Off" button is pressed, and goes out when it is pressed again. 3 "On/Off" button Press this button to switch the machine on. Press it again to switch the machine off. To empty out water there are 2 possibilities: · Select programme "Drain" and then depress the "Start/Pause" button: The water is emptied out without spinning. · Select the Spin programme : reduce the spin speed by means of the relevant button and then depress the "Start/Pause" button. The water is emptied out and the laundry is spun at the selected spin speed. Important ! Before selecting the "Drain" or "Spin" programmes, the selector dial must be positioned on Off (cancelling). The "Rinse hold" option CANNOT be selected for the automatic Washing & Drying programme. 4 "Spin" button Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washer-dryer or to select position "Rinse hold". The relevant light will light up. Spin speed The following speeds are available for the different fabrics: · Cottons, linen: 500/700/900 max 1400 r.p.m.; · Synthetics and wool: 500/700 max 900 r.p.m.; · Delicates and "30 Minute wash": 700 r.p.m. "Rinse Hold" position When RINSE HOLD option is selected, the last rinse water is not emptied out, to prevent the fabrics from creasing. When the programme has finished, the light of the "Start/Pause" button goes out, the light of the "Rinse hold" position and the "End" pilot light are alight to indicate that the water must be emptied out. The door is locked. 5 "Option" buttons Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before depressing the "Start/Pause" button. When these buttons are pressed, the corresponding pilot lights illuminate. When they are pressed again, the pilot lights go out. If an incorrect option is selected, the pilot lights flash for about 2 seconds, an acoustic signal is heard and the message Err is displayed. Press these buttons to select the following options: · "Prewash": select this option if you wish your laundry to be prewashed at 30°C max. before the main wash (not available for Wool and "30 Minute wash"). The prewash cycle ends with a short spin at 650 rpm in programmes for cotton and synthetic fabrics, whereas in the programme for delicate fabrics the water is only drained. This option can be selected for heavily soiled laundry. 14 Synthetics Cottons 30 Minute wash 90° · "Quick": select this option for laundry that is only slightly soiled in order to obtain a good wash result in a short time. This option is not available with the Wool programmes, the Energy saving programmes "Economy" and "30 Minute wash". The washing time will be reduced according to the type of fabric and the selected temperature. If you have already pressed the "Start/Pause" button, and you wish to cancel the delay time, proceed as follows: · set the machine to PAUSE by pressing the "Start/Pause" button; 0 · press the "Delay start" button until the symbol "0' " is displayed. · press the "Start/Pause" button again. Important! · The "Delay start" cannot be used with "Drain" or "Spin" programmes. Note! · With programme "Soak 30°" the selected delay (up to a maximum of 10 hours) corresponds to the soak time of the laundry in the drum. · The door will be locked throughout the delay time. If you need to open the door, you must first set the washer-dryer to Pause by pressing the "Start/Pause" button. After you have closed the door, press the "Start/Pause" button again. · "Extra rinse": this option can be selected with all programmes, except the Wool programmes and "30 Minute wash". The machine add 2 rinses for cotton and 1 rinse for synthetics and delicates. This option is recommended for people who are allergic to detergents, and areas where the water is very soft. 6 "Automatic Dry" button This button allows you to choose the required degree of drying for cottons and synthetics: - Extra dry (only for cottons) - Store dry (cottons and synthetics) - Iron dry (only for cottons) The drying time is automatically adjusted by the machine: the laundry will be dried to the selected degree of dryness. 9 "Start/Pause" button This button has two functions: · Start: after you have selected the desired programme and options, press this button to start the washerdryer. The light above the button will stop flashing and remain lit. If you have selected a delay time, the countdown will begin and will be shown on the display. · Pause: when you press this button again, the programme in progress is interrupted. The light above the button will start flashing. To restart the programme from the point at which it was interrupted, press the button again. Important! You must set the washer-dryer to Pause before you make any change in the programme in progress. 7 " Time dry" button If you wish to carry out a timed programme instead of an electronic programme push the button until the drying time you want appears in the display according to the fabrics (cotton or synthetics) you have to dry. For Cottons and Synthetics you can select a drying time from 10 minutes to 130 minutes. 8 "Delay start" button This button makes it possible to delay the starting of the programme 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 23 hours. The delay you have selected is shown on the display for about 3 seconds; afterwards, the duration of the programme reappears. You must select this option after you have set the programme and before you press the "Start/Pause" button. The time value shown on the display will decrease by one unit every hour. You can change the delay time at any moment, before you press the "Start/Pause" button. 15 10 Display (Programme time) The following pieces of information are shown on the display: · Reset/cancellation of the programme If the programme selector dial is turned to "Off" position, three blinking dashes are displayed. Now you can select a new programme. (If, at the end of a washing cycle, the programme selector dial has not been turned to "Off" position , when you press the "On/Off" button to switch the machine on for the next washing, the display will show a blinking zero.) After starting the programme, the remaining time is updated every minute. Important! If you select a drying time longer then 55' minutes, after 3 seconds, the display will show it in hours and minutes (see the example below). Example: --Time dry 55 1.00 Time dry · Duration of washing programme in hours and minutes, after you have selected a programme (for example 2.05). · The washer-dryer has stopped with water in the tub, when the "Rinse hold" option has been selected or at the end of the "Soak 30°": this is indicated by a flashing zero. · The washer-dryer has completed the programme: this is indicated by a flashing zero. 2.05 The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric. While the programme is running (after you have pressed the Start/Pause button), the displayed time value decreases by one unit every minute. 0 · Delay start, a time value indicated in hours (23 hours max) and selected by means of the relevant button. 1.25 Delay start · Selection of drying time in minutes. 105 The delay time is displayed for 3 seconds, then the duration of the selected programme reappears. After you have pressed the Start/Pause button, the countdown is updated every hour, and, for the last two hours, every 30 minutes. 16 · An incorrect option selection has been made: this is indicated by the message Err when a function incompatible with the current programme is selected. Important! If you turn the programme selector dial to another programme when the machine is working, all the lights of the programme progress display will flash for about 2 seconds but the machine will not perform the new selected programme. 12 Programme selector dial The programme selector dial is divided into the following sections: · Cottons, · An alarm code indicates a fault in the machine operation (see page 31, "Something Not Working"). · Synthetics, · Delicates · Wool / Hand washing · Special programmes from "Soak 30°" to "30 Minute wash" E20 · Reset programme "Off" Spin Drain Softeners Rinse Soak 30° Cold 30° 40° Delicates 30° Delicates 40° Off Economy 60° 60° Economy 40° 40° 30° Drying Economy 40° 40° Easy iron 40° Drying 60° 11 Programme phase indicator lights When you select a programme, the lights relevant to the phases that form the programme light up. After you have started the programme, only the light relevant to the phase that is currently being carried out will remain lit. When the washing or drying programme has finished, the "End" light comes on and a flashing zero appears on the display. The light of the `Start/Pause is off. Prewash Wash Rinse Rinse hold Drain Spin Drying End Wool The selector dial can be turned either clockwise or anticlockwise to select the required wash and drying programme . "Economy" position corresponds to an ENERGY SAVING programme and "Cold" to a cold wash. Before setting the dial to any position ensure that the machine is turned to the "Off" position. Important! At the end of the programme the selector dial must be turned to position "Off". 17 Synthetics Cottons 30 Minute wash 90° Programme information Easy iron 40° With this programme at 40°C it is possible to wash synthetic garments which must be ironed. The laundry is gently washed and spun to prevent the fabrics from creasing. Max. load 1 kg. Final spin speed 900 r.p.m. Important! The spin speed will automatically assume the setting for cotton items. If required, reduce the speed to the desired level by depressing the "Spin" button. Softeners Hand washed garments can be be starched or softened with this programme. The machine performs 1 rinse, followed by a final long spin at the maximum speed, which can be reduced by depressing the "Spin" button. The final spin is foreseen only for cotton items as in the spin programme. Soak 30° This is a special programme for heavily soiled laundry. The machine performs a soak of about 20 minutes at 30°C. At the end of the soak time the machine will stop automatically with water left in the tub. The display will show a flashing zero. Pour the detergent for the soak programme into the compartment marked . This programme cannot be used for very delicate fabrics or Wool. Before starting a new washing phase, it is necessary to empty out the water by: · Draining only: turn the programme selector dial to "Drain" programme". (Depress the "Start/Pause" button). · Draining and spin: turn the programme selector dial to programme "Spin", reduce the spin speed by means of the "Spin" button, and then depress "Start/Pause" button. Important! · At the end of the soak (after having emptied out the water) you can select the washing programme. First turn the programme selector dial to "Off", then select the programme and depress the "Start/Pause" button. Note! · With programme "Soak 30°" it is possible to select the delay start only up to a maximum of 10 hours and it corresponds to the soak time of the laundry in the drum. Drain For emptying out the water of the programme "Soak 30°" or at the end of a programme with the "Rinse hold" option. Turn first the programme selector dial to "Off", then select the "Drain" programme and depress the "Start/Pause" button. Spin Separate long spin at the max speed for hand washed garments. It has to be used for cotton items. You can reduce the speed by means of "Spin" button to adapt it to the fabrics to be spun. 30 Minute wash This is a complete programme that can be combined with the following options: Spin speed reduction, "Rinse hold" and "Delay start". To be used for laundry which is lightly soiled or which needs freshening up. Max. load 2 kg. Washing temperature 30 C. Programme duration 30 minutes. Final spin speed 700 rpm. Rinse With this programme it is possible to rinse and spin the garments which have been washed by hand. The machine performs 3 rinses, followed by a final long spin at the maximum speed. Off = Reset programme To reset a programme turn the selector dial to "Off". Now a new programme can be selected. 18 Operating Sequence Before the first wash, we recommend that you run a cotton cycle at 90°C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the dispenser drawer and start the machine. WASHING 5 KG OF WHITE COTTON AT 90°C 4. Switch the machine on To switch the machine on, press the ON/OFF button: the mains-on light comes on. To switch the appliance off, depress the same button. Suppose you have 5 kg of laundry to wash. It is white cotton and is suitable for high temperature washing. On/Off --0 1.Load the laundry Open the door. Place the laundry in the drum, one item at a time, shaking them out as much as possible. Close the door. If the programme selector dial is on the "Off" (Reset) position, three flashing dashes will be displayed. If the programme selector dial is positioned on a wash programme, a flashing zero appears on the display. 5. Select the desired programme/temperature P0004 2.Measure out the detergent Pull out the dispenser drawer until it stops. Measure out the amount of detergent required and pour it into the main wash compartment . If you wish to carry out the prewash or a soak programme, pour detergent into the appropriate compartment marked . Turn the selector dial to 90° programme. The lights relevant to the phases that form the programme will light up. The display will show the duration of the selected programme, calculated on the basis of the maximum load for each type of fabric. The Start/Pause button light will start flashing. If the load of laundry to be washed is small, at the beginning of the cycle the display will still indicate the duration relevant to the maximum load. The duration value will be gradually adjusted during the cycle. 3.Measure out the fabric softener If required, pour fabric softener into the compartment marked , without exceeding the «MAX» mark. Wool Spin Drain Softeners Rinse Soak 30° Cold 30° 40° Delicates 30° Delicates 40° Off Economy 60° 60° Economy 40° 40° 30° Drying Economy 40° 40° Easy iron 40° Drying 60° Cottons 30 Minute wash 90° C0111 C0112 Close the drawer gently. If your laundry needs a soak time, turn the programme selector dial to "Soak 30°" and then, before starting a washing cycle, empty the water as described in the "Soak 30°" paragraph. 19 Synthetics 2.05 6. Select the spin speed or the "Rinse hold" option Press the "Spin" button repeatedly in order to select the desired spin speed or the "Rinse hold" option. If you select the "Rinse hold" option, the machine will stop at the end of the programme with the water still in the tub. The relevant light will light up. The selected delay time value (up to 23 hours) will appear on the display for 3 seconds, then the duration of the programme will appear again. Delay start 1400 900 700 500 Rinse hold Spin During this period it is possible to load other laundry: press the "Start/Pause" button. Open the door. Load the laundry. Close the door and press the "Start/Pause" button again. 7. Select the desired options If your laundry is very dirty, it may be advisable to select the "Prewash" option. If your laundry is only slightly soiled, select the "Quick" option. If you wish the laundry to undergo an extra rinse, select the "Extra Rinse" option. The relevant light illuminates. 9. Start the programme Press the "Start/Pause" button. The relevant light will stop flashing, and only the light relevant to the phase that is in progress will remain lit. The machine starts operating. If you have chosen a delayed start, the washer dryer will begin the countdown. The display will show the duration of the programme or the selected delay. Prewash Quick Extra rinse 10. How to change an option or a programme during its cycle It is possible to change any option before the programme carries it out. Before you make any change, you must pause the machine by pressing the "Start/Pause" button. 8. Select the "Delay start" Before you start the programme, if you wish the start to be delayed, press the "Delay start" button repeatedly, or keep it pressed, to select the desired delay. Changing a running programme is possible only by resetting it. Turn the programme selector dial to "Off" and then to the new programme position. Start the new programme by depressing the "Start/Pause" button. The washing water in the tub will not emptied out. 20 11. How to interrupt a programme Depress the "Start/Pause" button to interrupt a programme which is running, the corresponding light starts to flash. Depress the button again to restart the programme. 13. End of programme At the end of the programme, the machine stops automatically and displays a flashing zero. The "End" light illuminates. If the "Rinse hold" option has been selected, the light of the "Start/Pause" button goes out, a flashing zero appears on the display, the "Rinse hold" pilot light and the "End" light are on (the door will be locked) to indicate that the water must be emptied out before opening the door. To drain the water or to spin see the paragraphs "Draining only" or "Draining and spin" on page 18. Release of the lock is also indicated by the illumination of the "End" light. Turn the programme selector dial to Reset "Off" and then press the "On/Off" button to switch the machine off. Remove the laundry from the washer dryer. Check whether the drum is completely empty, by rotating it with your hand. The purpose of this is to prevent any items of laundry from remaining accidentally in the drum, where they might get damaged in a subsequent wash (e.g. by shrinking) or bleed colour into another load of laundry. We advise you to close the water supply tap and disconnect the plug from the socket. Leave the door ajar in order to air the machine. 12. How to open the door during the cycle of a programme You can open the door, after having set the washerdryer to Pause, provided the following conditions exist: · the machine is not in the heating phase beyond 55°C; · the level of the water is not high; · the drum is not turning. If these requirements are met, when you pause the washer dryer, the door can be opened. Should it not be possible to open the door, and should it be absolutely necessary to do so, switch the machine off by pressing the "On/Off button. After approximately 3 minutes, you can open the door. Pay attention to the level and temperature of the water in the washer-dryer! When you close the door and press the "On/Off" button again, the machine will resume the programme from the point where it had been interrupted. 21 Drying DRYING 2.5 KG OF COTTON You have for example just machine-washed and spun at 1400 rpm 5 kg of laundry. They are cotton fabrics of medium weight which you want to iron as soon as they are dry. Remove the laundry from the appliance and divide the items to obtain two loads of approx. 2.5 kg each. The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. 1. Load the laundry. 2. Depress the "On/Off" button to switch the machine on. 3. Turn the programme selector dial to the "Drying" programme in the Cottons sector. 4. If you wish to carry out the electronic drying, depress "Automatic dry" button until the light "Iron Dry" illuminates. Extra dry Store dry Iron dry