User manual JVC AV28CH1EUB - AV28CH1 - Instruction Manual

ENGLISH ENGLISH DEUTSCH DEUTSCH FRANÇAIS FRANÇAIS NEDERLANDS NEDERLANDS CASTELLANO CASTELLANO ITALIANO ITALIANO PORTUGUÊS PORTUGU PORTUGUÊS AV28CH1EU AV28CH1EU COLOUR TELEVISION VICTOR COMPANY OF JAPAN, LIMITED INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI INSTRUÇÕES FARBFERNSEHGERÄT TELEVISEUR COULEUR KLEURENTELEVISIE TELEVISOR A COLOR TELEVISORE A COLORI TELEVISOR A CORES © 2001 VICTOR COMPANY OF JAPAN, LIMITED LCT1139-001A-U 0112-T-CR-JMUK Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS UNIT. 1. Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit. 2. Avoid damaging the AC plug and power cord. 3. Avoid improper installation and never position the unit where good ventilation is unattainable. When installing this television, distance recommendations must be maintained between the 15 cm floor and wall, as well as installation in a tightly enclosed area or piece of furniture. Adhere to the minimum distance guidelines shown for 10 cm 10 cm 15 cm safe operation. 4. Do not allow objects or liquid into the cabinet openings. 5. In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover. 6. The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it. 7. The main power button on the TV does not fully isolate the TV from the AC supply. If you are not going to use this TV for a long period of time, be sure to disconnect the AC plug from the AC socket. ENGLISH CONTENTS PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 T-V LINK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 REMOTE CONTROL BUTTONS AND FUNCTIONS . . . . . . . . 9 MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PICTURE SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 PICTURE FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SOUND SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 ADDITIONAL MENU OPERATIONS . . . . . . . . . . . . . . . . . . . . 27 ADDITIONAL PREPARATION. . . . . . . . . . . . . . . . . . . . . . . . . 29 CH/CC NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 TV BUTTONS AND PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . 32 TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 1 PREPARATION I Connecting the Aerial and VCR If connecting a VCR, follow A B C . If not connecting a VCR, follow 1. To operate T-V LINK functions, a T-V LINK compatible VCR must be connected to the EXT-2 terminal on the TV. For details about T-V LINK functions, see "T-V LINK FUNCTIONS" on page 5. Note: · For further details, refer to the manuals provided with the devices to be connected. · The connecting cables are not provided. · A video can be viewed from the VCR without performing C. For details, refer to your VCR instruction manual. · To connect additional external devices, please see "ADDITIONAL PREPARATION" on page 29. · When a decoder is connected to a T-V LINK compatible VCR, set the DECODER (EXT-2) function to ON. For details, see "Using the DECODER (EXT-2) function" on page 28. Otherwise, you will not be able to view scrambled channels. Aerial 75-ohm Coaxial Cable Back of the TV EXT-2 S EXT-3 S EXT-1 21-pin SCART Cable VCR 75-ohm Coaxial Cable To Aerial Input AV IN/OUT Terminal To Aerial Output I Connecting the power cord to the AC outlet Caution: · Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit. I Putting Batteries into the Remote Control Use two AAA/R03 dry cell batteries. Insert the batteries from the - end, making sure the + and polarities are correct. To open the battery compartment, slide the door downwards and lift off. Replace the door by sliding it upwards until it is secure. Note: · Follow the warnings printed on the batteries. · Battery life is about six months to one year, depending on your frequency of use. · If the remote control does not work properly, replace the batteries. · The batteries we supply are only for setting up and testing your TV, please replace them as soon as necessary. · Always use good quality batteries. 2 PREPARATION I Initial Settings When the TV is first turned on, it enters the initial setting mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to make the initial settings. 1 Press the Main power button on the TV. The Power lamp lights red (for power on), then green (for TV on) and the JVC logo is displayed. ENGLISH D0044-EN Note: · If the power lamp stays red and does not change to green: Your TV is in the standby mode. Press the # (Standby) button on the remote control to turn your TV on. · The JVC logo does not appear when your TV has been turned on once. In this case, use the "LANGUAGE" and "AUTO PROGRAM" functions to make the initial settings. For details, see "INSTALL" on page 23. Main power button Power lamp 2 Press the a button. The LANGUAGE menu appears. LANGUAGE 1 4 7 2 5 8 0 3 6 9 Yellow button Blue button AV BACK TV OK TV D0002(E)-EN P MENU OK 3 Press the 5 and 6 buttons to choose ENGLISH. Then press the a button. English is set for the on-screen display description. The COUNTRY menu appears as a sub-menu of the AUTO PROGRAM function. There are two COUNTRY menus. Pressing the yellow button changes the COUNTRY menu as follows: P TV BACK TV OK START MORE BACK TV OK START MORE D0003-EN 4 Press the 5 and 6 buttons to choose the country where you are now located. 3 PREPARATION 5 Press the blue button to start the AUTO PROGRAM function. The AUTO PROGRAM menu appears and received TV channels are automatically registered in the Programme numbers (PR). AUTO PROGRAM CH 10 20% 9 Now, the initial settings are complete, and you can watch the TV. Note: · When your TV can detect the TV channel name from the TV channel broadcast signal, it automatically registers the TV channel name (ID) to the Programme number (PR) in which the TV channel has been registered. · If a TV channel you want to view is not set to a Programme number (PR), manually set it using the MANUAL function. For details, see "EDIT/MANUAL" on page 24. · The TV channel is not registered in Programme number PR 0 (AV). When you want to register a TV channel to PR 0 (AV), manually set it using the MANUAL function. For details, see "EDIT/MANUAL" on page 24. EDIT PR AV 01 02 03 04 05 06 07 08 09 BACK TV OK ID BBC1 CH / CC CH CH CH CH CH CH CC CC CC 21 22 23 24 25 26 01 02 03 ID INSERT DELETE MANUAL BACK TV OK MOVE D0004-EN If "ACI START/ACI SKIP" appears in the AUTO PROGRAM menu: You can use the ACI (Automatic Channel Installation) function to decode the ACI data and complete the registration of all the TV channels in a short period of time. For details of the ACI function and how to use it, refer to "Using the ACI function" on page 27. If you don't want to use the ACI function, press the 6 button to choose ACI SKIP and then press a . To cancel the AUTO PROGRAM function: Press the b button. 6 After the TV channels have been registered in the Programme numbers (PR), the EDIT menu appears. You can proceed to edit the Programme numbers (PR) using the EDIT/MANUAL function. For details, see "EDIT/MANUAL" on page 24. When not using the EDIT/MANUAL function: If you do not need to use the EDIT/MANUAL function, go to the next step. 7 Press the a button to display the T-V LINK menu. T-V LINK DOWNLOAD TV VCR BACK TV OK EXIT D0005-EN 8 Operate the T-V LINK menu according to the type of a VCR connected to the EXT-2 terminal. When a T-V LINK compatible VCR is not connected: Press the b button to exit the T-V LINK menu. The T-V LINK menu disappears. When a T-V LINK compatible VCR is connected: Follow the operating procedure "Downloading the data to VCR" on page 27 to transmit the Programme number (PR) data. 4 T-V LINK FUNCTIONS When a T-V LINK compatible VCR is connected to the EXT-2 Terminal on the TV, it is easier to set up the VCR and to view videos. T-V LINK uses the following features: To use T-V LINK functions: A T-V LINK compatible VCR is necessary. The VCR must be connected to the EXT-2 terminal on the TV by a fully wired SCART cable. Note: · A "T-V LINK compatible VCR" means a JVC VCR with the T-V LINK logo or a VCR with one of the following logos. However, these VCRs may support some or all of the features described below. For details, refer to your VCR instruction manual. "Q-LINK" (a trademark of Panasonic Corporation) "Data Logic" (a trademark of Metz Corporation) "Easy Link" (a trademark of Phillips Corporation) "Megalogic" (a trademark of Grundig Corporation) "SMARTLINK" (a trademark of Sony Corporation) Note: · Operation via the TV is not possible. · Generally, the VCR cannot record a TV channel that cannot be received properly by the VCR's tuner, even though you can view that TV channel on the TV. However, some VCRs can record a TV channel by using the TV's output if that channel can be viewed on the TV, even though the TV channel cannot be received properly by the VCR's tuner. For details, refer to your VCR instruction manual. ENGLISH I TV Auto Power On/VCR Image View I Pre-set Download Download the registered data on the TV channels from the TV to the VCR. The Preset Download function automatically begins when the initial setting is complete or whenever the AUTO PROGRAM or EDIT/MANUAL operations are performed. Note: · This function can be operated via VCR operation. When the VCR starts playing, the TV automatically turns on and the images from EXT-2 terminal are displayed on the screen. When the VCR menu is operated, the TV automatically turns on and the images from EXT-2 terminal are displayed on the screen. Note: · This function does not operate if your TV's main power is turned off. Set your TV's main power to on (standby mode). When "FEATURE NOT AVAILABLE" is displayed: If "FEATURE NOT AVAILABLE" is displayed, the download was not performed correctly. Before trying to download again, ensure the following: · The VCR power is turned on. · The VCR is T-V LINK compatible. · The VCR is connected to the EXT-2 terminal. · The SCART cable is fully wired. I Direct Rec "What You See Is What You Record" You can record to VCR the images that you are currently viewing on TV by a simple operation. For details, read the manual for your VCR. Operate via the VCR. "VCR IS RECORDING" is displayed. In the following conditions, the VCR will stop recording if the TV is turned off, if the TV channel or input is switched, or if the menu is displayed on the TV: · When recording images from an external device connected to the TV. · When recording a TV channel after it has been unscrambled on a decoder. · When recording a TV channel by using the TV's output because that TV channel cannot be properly received on the VCR's tuner. 5 BASIC OPERATION I Turn the Main power on Press the Main power button on the TV. The Power lamp lights red and your TV is in the standby mode. Note: · If the Power lamp lights green, the TV is already on. To turn the Main power off: Press the Main power button again. The Power lamp goes off. Caution: · The main power button on the TV does not fully isolate the TV from the AC supply. If you are not going to use this TV for a long period of time, be sure to disconnect the AC plug from the AC socket. Main power button Power lamp I Turn the TV on from standby mode Press the # (Standby) button, the b button, the 6 buttons or the Number buttons. The Power lamp lights red to green and your TV will be turned on. 1 4 7 2 5 8 0 3 6 9 To turn the TV off: Press the # (standby) button again. The Power lamp changes from green to red and the TV enters standby mode. Number buttons I Choose a TV channel Choose a Programme number (PR) in which the desired Programme TV channel has been set. AV Use the 6 buttons: Press the 6 buttons to choose the desired Programme number (PR). Use the Number buttons: Enter the desired Programme number (PR) with the Number buttons. Example · PR 12 press 1 and 2. · PR 6 press 6. Use the PR LIST: P TV MENU OK P F.T/L FREEZE SUB-P 1 Press the h (Information) button to display the PR LIST. PR LIST PR AV 01 02 03 04 05 06 07 08 09 TV OK TV ID BBC1 -10 +10 6 D0006-EN BASIC OPERATION 2 Press the 5 and 6 buttons to choose a Programme number (PR). Then press the a button. Note: · For Programme numbers (PR) with the CHILD LOCK function set, the n (CHILD LOCK) mark is displayed next to the Programme number (PR) in the PR LIST. · You cannot use the 6 buttons to choose a Programme number (PR) with the CHILD LOCK funtion set. · Even if you try to choose a Programme number (PR) with the CHILD LOCK function set, the n (CHILD LOCK) mark will appear, and you cannot watch the TV channel. To watch the TV channel, see "CHILD LOCK" on page 21. · If you do not have a clear picture or no colour appears, change the colour system manually. See "COLOUR SYSTEM" on page 16. Use the 6 buttons: Press the 6 buttons to choose an EXT terminal. Use the PR LIST: 1 Press the h (Information) button to display the PR LIST. 2 Press the 5 and 6 buttons to choose an EXT terminal. Then press the a button. ENGLISH Note: · The EXT terminals are registered after the Programme number PR 99. · You can choose a video input signal from the S-VIDEO signal (Y/C signal) and regular video signal (composite signal). For details, see "S-IN (S-VIDEO input)" on page 19. · If you do not have a clear picture or no colour appears, change the colour system manually. See "COLOUR SYSTEM" on page 16. · When choosing an EXT terminal with no input signal, the EXT terminal number becomes fixed on the screen. · This TV set has a function which can automatically change over the input according to a special signal output from an external device. (The EXT-4 terminal does not support it.) I Adjust the volume Press the 5 buttons to adjust the volume. The Volume indicator appears and the volume changes as you press the ­/+ buttons. To return to a TV channel: Press the b button, the 6 buttons or the Number buttons. I Watch images from external To use the Programme number PR 0 (AV): When the TV and VCR are connected only by the Aerial cable, choosing the Programme number PR 0 (AV) allows you to view images from the VCR. Set the VCR RF channel to the Programme number PR 0 (AV) manually. For details, see "EDIT/MANUAL" on page 24. Pressing the o button changes the choice as follows: TV mode Programme numbers PR 1 ­ PR 99 PR 0 devices Choose an EXT terminal to which the desired external device has been connected. Use the o button: Press the o button to choose an EXT terminal. Pressing the o button changes the choice as follows: TV mode Programme numbers PR 1 ­ PR 99 EXT modes EXT modes EXT-1 EXT-2 EXT-1 EXT-2 EXT-4 EXT-3 EXT-4 EXT-3 Note: · The VCR RF channel is sent as the RF signal from the VCR. · Also refer to your VCR instruction manual. 7 BASIC OPERATION I Operating with the buttons on the TV 1 2 Press the P p buttons to turn the TV on from standby mode. Press the P p buttons to choose a Programme number (PR) or an EXT terminal. Press the r (Volume) button and the q buttons to adjust the volume. 1 Press the r (Volume) button. The volume level indicator appears. Behind the Cover 3 2 Press the q buttons while the volume level indicator is displayed. 8 REMOTE CONTROL BUTTONS AND FUNCTIONS 1 Muting Button You can turn the volume off instantly. Press the l (Muting) button to turn off the Volume. Pressing the l (Muting) button again resumes the previous Volume level. 1 4 7 2 5 8 0 3 6 9 ENGLISH 2 Number Buttons You can choose a Programme number (PR) by entering the Programme number. Example: · PR 12 press 1 and 2. · PR 6 press 6. You can also press the o button repeatedly to choose an EXT terminal. AV P TV MENU OK 3 ZOOM Button P F.T/L You can change the screen size according to the picture aspect ratio. Choose the optimum one from the following ZOOM modes. AUTO: For any picture format except Normal Picture (4:3 Aspect Ratio), the picture will be automatically displayed in the optimum screen size. For Normal Picture (4:3 Aspect Ratio), the picture displayed in accordance with the ZOOM mode set on the 4:3 AUTO ASPECT menu. For details, see "4:3 AUTO ASPECT" on page 17. Note: · AUTO may not function properly with poor signal quality. In this case, choose an optimum ZOOM mode manually. · This TV supports WSS (wide-screen signals). When broadcasts with WSS are received with the ZOOM mode set at AUTO, the most suitable ZOOM mode is automatically chosen according to the WSS received. REGULAR: TV Use to view a normal picture (4:3 aspect ratio) as its original size is. PANORAMIC: This mode stretches the left and right sides of a normal picture (4:3 Aspect Ratio) to fill the screen, without making the picture appear unnatural. Note: · The top and bottom of the picture are slightly cut off. 9 REMOTE CONTROL BUTTONS AND FUNCTIONS 14:9 ZOOM: This mode zooms up the Wide Picture (14:9 Aspect Ratio) to the upper and lower limits of the screen. Adjusting the visible area of the picture If subtitles or the top (or bottom) of the picture are cut off, adjust the visible area of the picture manually. 1 Press the c button. The ZOOM menu appears. 16:9 ZOOM: This mode zooms up the Wide Picture (16:9 Aspect Ratio) to the full screen. 2 Press the a button to display the ZOOM mode indication. Indicator is displayed. 16 : 9 ZOOM D0010-EN 16:9 ZOOM SUBTITLE: This mode zooms up the Wide Picture (16:9 Aspect Ratio) with subtitles to the full screen. 3 While it is displayed, press the 6 buttons to adjust the visible area vertically. Note: · You cannot adjust the visible area in REGULAR or FULL mode. FULL: This mode uniformly stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the wide TV screen. 4 HYPER SOUND Button You can enjoy sounds with a wider ambience. Press the / (HYPER SOUND) button to turn the HYPER SOUND function on or off. Note: · Use for pictures with a 16:9 aspect ratio that have been squeezed into a normal picture (4:3 aspect ratio), you can restore their original dimensions. Note: · The HYPER SOUND function does not work properly with mono sound. · The HYPER SOUND function can be also turned on or off by using the SOUND SETTING menu. For details, see "HYPER SOUND" on page 18. Choose the ZOOM mode 1 Press the c button to display the ZOOM menu. ZOOM AUTO REGULAR PANORAMIC 14:9 ZOOM 16:9 ZOOM 16:9 ZOOM SUBTITLE FULL BACK TV OK D0009-EN 2 Press the 6 buttons to choose a ZOOM mode. Then press the a button. The picture expands and the chosen ZOOM mode is displayed in about 5 seconds. Note: · The ZOOM mode may be automatically changed due to the control signal from an external device. When you want to return to the previous ZOOM mode, choose the ZOOM mode again. 10 REMOTE CONTROL BUTTONS AND FUNCTIONS 5 Information Button You can display the PR LIST or the Current Time on the screen. 8 Standby Button Press the # (Standby) button to turn the TV on or off. When the TV is turned on, the power lamp changes from red to green. Press the h (Information) button. Pressing the h (Information) button changes the display as follows: PR LIST PR AV 01 02 03 04 05 06 07 08 09 TV OK 9 Colour Buttons ID BBC1 12 : 00 The colour buttons are used for the teletext operations or the menu operations. For details, see "~ Teletext Control Buttons and VCR P DVD Switch" on page 12 or "MENU OPERATION" on page 14. ENGLISH 0 OK Button No indication The a button is used to operate menus. For details, see "MENU OPERATION" on page 14. - 6 Buttons You can choose a Programme number (PR) or an EXT terminal. -10 D0011-EN +10 Note: · You can choose Programme numbers (PR) or EXT terminals with the PR LIST. For details, see "Use the PR LIST:" on page 6. · This TV uses teletext data to set the current time. If the TV has not received a TV channel that has teletext programmes since it was turned on, the time display is blank. To view the current time, choose a TV channel that has teletext programmes. The time will still be displayed as long as you do not turn off the TV, even if you choose other TV channels. · When watching videos, an incorrect current time is sometimes displayed. · The h (Information) button is also used to operate menus. For details, see "MENU OPERATION" on page 14. Press the 6 buttons to choose an Programme number (PR) or an EXT terminal. The 6 buttons are also used to operate menus. For details, see "MENU OPERATION" on page 14. = VCR/DVD Control Buttons and VCR P DVD Switch These buttons can be used to operate a JVC brand VCR or DVD player. Pressing the button having the same appearance as the original remote control button of a device makes the function work in the same way as the original remote control. 1 Set the VCR P DVD Switch to the VCR or DVD position. VCR: When you are operating the VCR, set the switch to the VCR position. DVD: When you are operating the DVD player, set the switch to the DVD position. 6 TV Button You can return to a TV channel instantly. Press the b button. The TV returns to the TV mode and a TV channel appears. Note: · The b button is also used to operate menus. For details, see "MENU OPERATION" on page 14. 2 Press the VCR/DVD Control Button to control your VCR or DVD player. 7 5 Buttons You can adjust the volume. Press the 5 buttons to adjust the sound. Note: · The 5 buttons are also used to operate menus. For details, see "MENU OPERATION" on page 14. Note: · If your device is not made by JVC, these buttons cannot be used. · Even if your device is made by JVC, some of these buttons or any one of the buttons may not work, depending on the device. · You can use the p buttons to choose a TV channel. The VCR will receive or choose the chapter the DVD player plays back. · Some DVD player models use the p buttons for both operating of Fast forward/backward functions and choosing the chapter. In this case, the 1/¡ the buttons do not work. 11 REMOTE CONTROL BUTTONS AND FUNCTIONS I ~ Teletext Control Buttons and VCR P DVD Switch Using the List Mode You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons. P TV MENU OK To store the page numbers: 1 Press B button to engage the List mode. P F.T/L The stored page numbers are displayed at the bottom of the screen. 2 Press a Colour button to choose a position. Then press the Number buttons to enter the page number. 1 2 5 8 0 3 6 9 Basic operation You can view three types of teletext broadcasts on the TV: FLOF (Fastext), TOP and WST. 4 7 AV 1 Choose a TV channel with a teletext broadcast. 3 Press and hold down A (Store) button. The four page numbers blink white to indicate that they are stored in memory. 2 Set the VCR P DVD switch to the P (Text) position. To call up a stored page: 1 Press the B button to engage the List 3 Press g (Text) button to display the teletext. Pressing g (Text) button changes the mode as follows: TEXT --TEXT --- mode. 2 Press a colour button to which a page has been assigned. To exit the List mode: Press the B button again. Text mode D0043-EN TV mode 4 Choose a teletext page by pressing the 6 buttons, Number buttons or Colour buttons. To return to the TV mode: Press the b button or g (Text) button. Note: · If you have trouble receiving teletext broadcasts, consult your local dealer or the teletext station. · The ZOOM function will not operate in the TV and text mode or Text mode. · No menu operations are possible when viewing a teletext programme. · Language display depends on the country which was set on the COUNTRY menu. If characters on a Teletext programme do not appear properly, change the COUNTRY Setting to other country's. For detail, "Changing the COUNTRY setting" on page 27. 12 REMOTE CONTROL BUTTONS AND FUNCTIONS Hold You can hold a teletext page on the screen for as long as you want, even while several other teletext pages are being received. Size You can double the height of the teletext display. Press the F (size) button. Press the C (Hold) button. Hold indication ENGLISH To cancel the Hold function: Press C (Hold) button again. Sub-page Some teletext pages include sub-pages that are automatically displayed. You can hold any sub-page, or view it at any time. Index You can return to the index page instantly. 1 Press the D (Sub-page) button to operate the Sub-page function. Sub-page numbers are displayed at the left of the screen. Colour* Yellow White Blue or Red Meaning of sub-page number Currently being displayed. Can be displayed. Cannot be displayed and it is not sent. Press G (Index) button. FLOF (Fastext)/TOP/WST: Returns to page 100 or a previously specified page. List mode: Returns to the page number displayed in the lower left area of the screen. Cancel You can search for a teletext page while watching TV. *: Background color of the sub-page number. 1 Press the Number button to enter a page number, or press a Colour button. The TV searches for a teletext page. 2 Press the 6 buttons to choose a subpage number. To cancel the Sub-page function: Press the D (Sub-page) button again. 2 Press H (Cancel) button. The TV programme appears. When the TV finds the teletext page, its page number appears in the upper left of the screen. Reveal Some teletext pages include hidden text (such as answers to a quiz). You can display the hidden text. 3 Press H (Cancel) button to return to a teletext page when the page number is on the screen. Note: · The TV mode cannot be resumed even by pressing the H (Cancel) button. A TV programme is temporarily displayed instead of the teletext programme. Each time you press the E (Reveal) button, text is hidden or revealed. 13 MENU OPERATION This TV has a number of functions you can operate using menus. To fully utilize all your TV's functions, you need to understand the basic menu operating techniques fully. 4 Press a button to complete the setting. The menu disappears. 1 Press the a button to display the MENU (main menu). The MENU (main menu) appears. In it, the titles of the menus are displayed. MENU PICTURE SETTING PICTURE FEATURES SOUND SETTING EXT SETTING BACK TV OK To return to the previous menu: Press h (information) button. To exit a menu instantly: Press the b button. FEATURES INSTALL Note: · When a menu is displayed on the screen, the ZOOM mode may be automatically changed to the FULL mode. This is not a malfunction. When the menu disappears, the ZOOM mode will return to the previously set ZOOM mode. D0013-EN 2 Press the 6 buttons to choose a menu title, and press the a button. The menu appears. PICTURE SETTING TINT CONTRAST BRIGHT SHARP COLOUR HUE BACK TV OK NORMAL RESET D0014-EN 3 Operate the menus according to the operation description of each function. Note: · For details, refer to the operation descriptions of each function described for each menu which follows this "MENU OPERATION". · The display appearing at the bottom of a menu indicates a button on the remote controller you can use when you operate a chosen function. 14 PICTURE SETTING PICTURE SETTING TINT CONTRAST BRIGHT SHARP COLOUR HUE BACK TV OK NORMAL Note: · You can change the HUE setting (picture hue) only when the colour system is NTSC 3.58 or NTSC 4.43. To return to the default settings in each TINT mode: RESET D0014-EN Press the blue button. Returns the picture settings in the currently chosen TINT mode to the default settings, and stores them in the TINT mode again. ENGLISH To display the PICTURE SETTING menu: 1 Press the a button to display MENU 3 Press the a button to complete the settings. The menu disappears. (main menu). 2 Press the 6 button to choose PICTURE SETTING, and press the a button. I TINT You can select one of three TINT modes (three kinds of picture settings) to adjust the picture settings automatically. 1 Press the 6 buttons to choose TINT. 2 Press 5 buttons to choose a mode. COOL: A cool white colour base with a boost in the colour and contrast levels that creates a more vivid picture. WARM: A warm orange/red colour base that creates the appropriate colour and contrast levels for watching films. NORMAL: A normal white colour base with normal colour and contrast levels. 3 Press the a button to complete the setting. The menu disappears. I Picture Adjustment You can change the picture settings of each TINT mode as you like. The picture settings changed are stored in the TINT mode. 1 Press the 6 buttons to choose an item. 2 Press the 5 buttons to change the setting. 2 Lower Darker Softer Lighter Reddish Item CONTRAST (picture contrast) BRIGHT (picture brightness) SHARP (picture sharpness) COLOUR (picture colour) HUE (picture hue) 3 Higher Brighter Sharper Deeper Greenish 15 PICTURE FEATURES PICTURE FEATURES DIGITAL VNR COLOUR SYSTEM 4:3 AUTO ASPECT BACK TV OK I COLOUR SYSTEM AUTO The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. 1 Press the 6 buttons to choose COLOUR SYSTEM. Then press the a button. The Sub-menu of the COLOUR SYSTEM function appears. COLOUR SYSTEM D0015-EN To display the PICTURE FEATURES menu: 1 Press the a button to display MENU (main menu). 2 Press the 6 button to choose PICTURE FEATURES, and press the a button. TV PAL BACK OK I DIGITAL VNR The DIGITAL VNR function cuts down the amount of noise in the original picture. You can choose from the three DIGITAL VNR function settings of AUTO, MIN and MAX. Note: · If you set the DIGITAL VNR effect too high it can make the picture less sharp. It is recommended to use the AUTO setting if you can. D0016-EN 2 Press the 5 buttons to choose the appropriate colour system. PAL: PAL system SECAM: SECAM system NTSC 3.58: NTSC 3.58 MHz system NTSC 4.43: NTSC 4.43 MHz system AUTO: This function detects a colour system from the input signal. Only when you are viewing a picture from Programme number PR 0 (AV), or EXT terminal, you can choose using the AUTO function. 1 Press the 6 buttons to choose DIGITAL VNR. 2 Press the 5 buttons to choose a setting. AUTO: The TV will automatically adjust the level of the DIGITAL VNR effect to match the amount of noise in the picture, giving you the best possible picture. MIN: The level of the DIGITAL VNR effect is set to the minimum. If you set the DIGITAL VNR function to AUTO but feel that the sharpness of the original picture has not been reproduced fully, change the setting from AUTO to MIN. · The MIN setting is not suitable for low-quality pictures which contain a lot of noise. MAX: The level of the DIGITAL VNR effect is set to the maximum. If you set the DIGITAL VNR function to AUTO but still notice some noise, change the setting from AUTO to MAX. · The MAX setting is not suitable for high-quality pictures which contain very little noise. 3 Press the a button to complete the setting. The menu disappears. Note: · The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. · When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3.58 or NTSC 4.43. 3 Press the a button to complete the setting. The menu disappears. 16 PICTURE FEATURES I 4:3 AUTO ASPECT You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Press the 6 buttons to choose 4:3 AUTO ASPECT. Then press the a button. The Sub-menu of the 4:3 AUTO ASPECT function appears. 4:3 AUTO ASPECT PANORAMIC REGULAR 14:9 ZOOM BACK TV OK ENGLISH D0017-EN 2 Press the 6 buttons to choose a ZOOM mode. 3 Press the a button to complete the settings. The menu disappears. 17 SOUND SETTING SOUND SETTING STEREO/ BASS TREBLE BALANCE HYPER SOUND OFF ON