Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia, Hong Kong and U.K.) MICRO COMPONENT SYSTEM UX-N1S Adjusting the voltage selector Use a screwdriver to slide the voltage marker so that it is set to the same voltage as where you are plugging in the unit. Bottom of the unit CAUTION: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1. Front: No obstructions and open spacing. 2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below. 3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more. Front view 15 cm 1 cm 15 cm 1 cm 15 cm 10 cm SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W 15 cm 15 cm Side view Basic and Common Operations Operating on the System To Turn on or off (standby) the power Press The STANDBY lamp on the System turns off/ on. See "Playing Back Discs" on page 4. Select a source* See "Listening to FM and AM Broadcasts" on page 5. See "Connecting a Portable Audio Device" on page 6. Adjust the volume * You can operate the source select buttons on the System only touch lightly, because these buttons are "touch sensor panel." If you touch any one of these buttons, they lights in blue briefly. You can adjust the volume level from level 0 (VOL MIN) to level 31 (VOL MAX). Adjust the volume Drop the volume in a moment Reinforce the bass sound Select a source See "Listening to FM and AM Broadcasts" on page 5. See "Connecting a Portable Audio Device" on page 6. You can adjust the volume level from level 0 (VOL MIN) to level 31 (VOL MAX). To restore the volume, press again, or adjust the volume level. AHB PRO indicator appears on the display. To cancel this function, press again. Press once to adjust the bass level or press twice to adjust the treble level. Then press VOLUME + to increase the level or press VOLUME ­ to decrease it. · You can adjust the bass and treble level from ­3 to +3. Press when the System is turned on. To cancel this function, press again. Press and hold for more than 2 seconds when the System is on standby. To cancel this function, press and hold for more than 2 seconds again. · Setting the Save mode allows you to reduce power consumption by turning the display off while on standby. Press briefly (except for FM mode). For setting the clock, see page 5. Press and hold until A.STBY indicator appears on the display. To cancel this function, press and hold again. · If no operation is done for about 3 minutes after CD playback stops, the System turns off. Press briefly and repeatedly to specify the time (in minutes) as follows: QP Link indicator (See page 6.) Main Display Turn off the System by using the sleep timer 10 20 30 60 90 120 150 Using Headphones Be sure to turn down the volume before connecting or wearing the headphones. · Connecting the headphones will deactivate the speakers. Operating on the Remote Control To Turn on or off (standby) the power Press The STANDBY lamp on the System turns off/ on. See "Playing Back Discs" on page 4. --Consists of CA-UXN1S and SP-UXN1S UX-N1W --Consists of CA-UXN1W and SP-UXN1W About the cooling fan A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus assuring normal operation of the unit. AC 110V 220-240V The model information is located on the bottom. INSTRUCTIONS GNT0065-018A[US/UB/A/UW/UJ] 0306MOCMDWJSC Voltage marker Precautions Notes on the power cord · When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small amount of power (5.0 W) is always consumed while the power cord is connected to the wall outlet. · When unplugging the System from the wall outlet, always pull the plug, not the power cord. · Do not handle the power cord with wet hands. · Disconnect the power cord before cleaning the System or moving the System. · Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents. · If the cord is damaged, consult a dealer and have the power cord replaced with a new one. Avoid moisture, water, dust, and high temperatures · Do not place the System in moist or dusty places. · If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using the System in this state may cause a fire or electrical shock. · Do not expose the System to direct sunlight or place it near a heating device. Notes on installation · Select a place which is level, dry and neither too hot nor too cold between 5°C and 35°C. · Do not install the System in a place subject to vibrations. · Do not put heavy objects on the System. To prevent malfunction or damage of the System · Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System. · Do not block the vents. To clean the cabinet · Use a soft cloth. Follow the relevant instructions on the use of chemically-coated cloths. · Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring. ©2006 Victor Company of Japan, Limited Warnings, Cautions and Others Caution -- button! Disconnect the mains plug to shut the power off completely. When installing the apparatus, ensure that the plug is easily accessible. The button in any position does not disconnect the mains line. The power can be remote controlled. · When the unit is on standby, the STANDBY lamp lights red. · When the unit is turned on, the STANDBY lamp goes off. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. CAUTION: · Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) · Do not place any naked flame sources, such as lighted candles, on the apparatus. · When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. · Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Caution for mains (AC) line BEFORE PLUGGING IN, check that your mains (AC) line voltage corresponds with the position of the voltage selector switch on the bottom of the unit and, if different, set the voltage selector correctly to prevent any damage or risk of fire/electric shock. CAUTION: DO NOT plug in before setting the voltage selector and all connection procedures are complete. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the System; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. Adjust the tone (Bass/ Treble) Point it at the remote sensor on the front panel. (The operating range is approx. 7 m.) Changing the display brightness STANDBY lamp Set the Save mode NOTE DO NOT turn off (standby) the System with the volume set to an extremely high level; Otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start playback. Display Information Disc play mode indicators (See page 4.) Tuner mode indicators (See page 5.) Timer mode indicators (See the right column and page 5.) Changing the display information (Clock and Source) Turn off the System automatically after CD playback is over (AUTO STANDBY function) [European Union only] There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer. Canceled · To check the time remaining until the shut-off time after setting the sleep timer, press SLEEP once. AHB PRO and A.STBY indicator (See the right column.) 1 3 Getting Started Supplied Accessories After unpacking, check to be sure that you have all the following items. The number in parentheses indicates the quantity of each piece supplied. · Remote control (x 1) · Lithium coin battery CR2025 (x 1) (The battery has been installed when shipped from the factory.) · AM loop antenna (x 1) · FM antenna (x 1) · AC plug adapter (x 1) (except for Hong Kong and Australia) If anything is missing, consult your dealer immediately. Playing Back Discs Prepare the Remote Control When you use the remote control for the first time, pull out the insulation sheet. Insulation sheet NOTES · Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. · Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of these things may cause the battery to give off heat, crack, or start a fire. · Do not leave the battery with other metallic materials. Doing this may cause the battery to give off heat, crack, or start a fire. · When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start to give off heat, crack, or start a fire. · Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to give off heat, crack, or start a fire. · Dispose of battery in the proper manner, according to federal, state, and local regulations. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. This System can play back the following discs--regular CD and CD-R/CD-RW (recorded either in the audio CD or MP3 format). · When playing back the MP3 track, MP3 indicator appears on the display. Programming the Playing Order--Program Play (except for MP3) To Set a Disc 1 On the System 2 3 1 On the System Press repeatedly until the PRGM (program) indicator appears on the display before you start playback. or Select the track number to program. Replacing the Battery in the Remote Control Insert the battery into the remote control by matching the polarity (+ and ­) correctly. Lithium coin battery (product number: CR2025) 2 3 Press to program the selected track. Repeat step 2 and 3 to program other tracks you want. · If you try to program a 33rd track, "FULL" will appear on the display. The tracks are played in the order you have programmed. The disc cover on the System opens. Connections Do not connect the AC power cord until all other connections have been made. NOTES · Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception. · If the cords are covered with vinyl, remove the vinyl to expose the tip of the cord by twisting the vinyl. Place a disc correctly with its label side up, then press down on the portions around the disc's center hole until you hear a click. · When removing the disc, take out the disc by holding it at the edge with pressing the System's pivot lightly. The disc cover on the System closes. · Do not close forcibly the disc cover with the hand. 4 5 Operations on the Program Play Mode Basic Disc Operations FM antenna (supplied) Extend it so that you can obtain the best reception. Playback the disc To connect the AM loop antenna 1 Hold To Press Check the programmed contents To erase the last step To erase the entire program To exit from program play or Press Press while playback is stopped. AM loop antenna (supplied) Turn it until the best reception is obtained. To assemble the AM loop antenna To On the System On the remote Current track number and elapsed playing time appear on the main display. · During playback, press again to stop playing for a moment. · While playback is stopped, total track number and total playing time (for MP3 disc, group number and track number) appear on the main display. Increases the track numbers. Press while playback is stopped. Press twice while playback is stopped to exit from the program play. · The stored program is erased. For better FM/AM reception 2 Insert 3 Release Stop playback Outdoor FM antenna (not supplied) PHONES RIGHT SPEAKERS LEFT COAXIAL ANTENNA Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 wire with coaxial type connector. Select a track Decreases the track numbers. Increases the group numbers while playback is stopped. Decreases the group numbers while playback is stopped. Fast-forwards the track by pressing briefly. To stop searching, press 6. Fast-reverses the track by pressing briefly. To stop searching, press 6. Playing Repeatedly--Repeat Play Press repeatedly before y ...