User manual JWIN JC-CD160 - INSTRUCTION MANUAL

FUNCTION OF CONTROLS R 17 1 7 19 18 5 6 14 16 9 LUD C D / C D - R / C D - R W PLAYE R LUD PUSH SEL JC-CD160 DISP RPT RDM SCAN ALL DIR SONG CLASSIC BND JAZZ MUT CLK 3 MUSIC MUTE LOUD MONO AF PTY EON ST LOC LUD Instruction Manual 60 WATT/DIGITAL TUNING SYSTEM SCN A/PS 1 LUD 2INT 3RPT 4RDM 5 6 MODE 20 15 LUD 21 22 23 12 13 8 4 2 11 10 C D / C D - R / C D - R W PLAYE R LUD PUSH SEL DISP RPT RDM SCAN ALL DIR SONG CLASSIC BND JAZZ MUT CLK CONTROL FUNCTIONS 1POWER ON/OFF Press the button to power up the unit Press and hold for more than 1 second to turn off unit. 2,3. SEL (control mode select)/MENU KEY Push to select the desired mode,VOL(volume),BAS(bass),TRE(treble) BAL(balance),or FAD(fader). This button normally functions as the volume control.Adjust the level rotate(3) clockwise after selecting the desired control mode. Otherwise the mode will go back to the volume control mode. Control Mode Volume control Bass control Treble control Balance control Fader control Turn clockwise: For less volume For less bass For less treble To decrease the right speaker volume To decrease the front speaker volume Turn counter clockwise: For more volume For more bass For more treble To increase the left speaker volume To increase the rear speaker volume MUSIC MUTE LOUD MONO AF PTY EON ST LOC LUD 60 WATT/DIGITAL TUNING SYSTEM SCN A/PS 1 LUD 2INT 3RPT 4RDM 5 6 MODE CAR CD PLAYER ASP 12/45SEC RECEIVER(AM/FM) DETACHABLE FRONT PANEL MENU KEY Hold the SEL key to choose the menu. 1) menu1: AUDIO DSP FUNCTION Press and hold longer than one second to activate the DSP feature.Rotate the SEL knob to select DSP mode sound effect as shown in sequence below .User setting value of bass/treble in normal mode is always memorized.In rock/classic/pops mode,bass/treble mode is skipped and level is not changeable FLAT----CLASSICS----POP M----ROCK M----DSP OFF. Bass and Treble gain of each mode is as shown in below table. Initial value of bass/treble in NORMAL mode is 0 dB. -- 1 -- LCD DISPLAY NORMAL FLAT ROCK CLASSIC POP DSP OFF FLAT M ROCK M CLASSIC M POP M BASS (F=100HZ) X dB 0 dB 6 dB 2 dB -4 dB MID (F=1KHZ) TREBLE (F=10KHZ) 0 dB 0 dB 0 dB 0 dB 0 dB X dB 0 dB 2 dB 2 dB -2 dB 8. LOCAL/DISTANT BUTTON Press local/distant(LO/DX) button for listening to weak stations.LOC indicator will appear on the display. Press this button again (Distant mode) for normal operation. 9. DISPLAY BUTTON (Set the Clock) Selects radio frequency or clock display. To set the clock: 1.With clock display selected,hold down the (CLK) button until clock display starts flashing. 2.Press (-) to change minutes,(+) to change hours. 3.Press (CLK) button to start the clock. 10. PRESET STATIONS Six numbered preset button store and recall stations for each band. Storing station 1.Select a band (if needed) 2.Select a station 3.Hold a preset button longer than one second.Preset station number appears in the display when station is saved. Recall a station: 1.Select band (if needed) 2.Press a preset button for less than one second to select stored station. 11. AUTOMATICALLY STORE STATIONS Select six strong stations and store them in current band. 1.Select a band (if needed) 2.Hold A/PS button for more than three seconds.The new station replace stations already stored in that band. Preset A/PS 1.Select a band (if needed) 2.Touch A/PS for more than one second but less than three seconds.Radio pauses for five seconds at each station.Touch A/PS again to stop scanning when the desired station is reached. 12.STEREO/MONO SELECTOR This function will only affect FM reception.Press this button if the FM reception becomes noisy/hissy. If the station being received is in stereo,it will now be played in mono.Press this button again to return tthe receiver to normal reception 13.MODE BUTTON (MODE) By pressing this key,user can select RADIO mode,AUX mode,CD PLAYER mode. 14.MUTE BUTTON Press the MUTE button to stop and the lcd will flashing indication "MUTE". To stop this function, press again the same button. 15. SCAN BUTTON Press this button briefly (LESS THAN 2 SEC.)and the radio will tune to the next memory preset station, pausing for 6 seconds, and repeating the process endlessly until a selection is made. To stop scanning, press this button briefly once again, or press the preset button that Corresponds to the channel number blinking on display. 16.PANEL RELEASE BUTTON Press the button and the right-side section of the panel will release. 2) menu2:BEEP ON--BEEP OFF The situation of beep sound is selected.The 2 mode is selected as also vol up or vol dn key. BEEP ON mode: A beep sound is generated when each key is pressed. BEEP OFF mode: The beep sound is disabled. 3) menu3:VOL LAST--VOL Addition VOLUME ELEVEL is determined when POWER ON LAST VOLUME:Final VOLUME LEVEL generates power before power off. ADJUST VOLUME:VOLUME LEVEL selected by the user is produced. 4) menu4:SEEK1--SEEK2 SEEK1:SEEK is activated right away when key is pressed for longer than 500ms. SEEK2:SEEK is activated after key is released. 5) menu5:ESP12--45 OPTION While ANTI-SKIP PROTECTION FUNCTION (ASP) If in use,the player is likely to receive shocks or vibrations.The ANTI-SHOCK FUNCTION is active to provide uninterrupted playback. Should the player receive shocks for more than 45 seconds continuously in cd playback playback,the sound will mute for a very short while and will resume once the player has stabilised from the shock. ESP12:Selected ESP time 12 seconds. ESP45:Selected ESP time 45 seconds. 4. LOUDNESS BUTTON -Press this button to boost the bass and treble response.Push the button again to return to normal operation.This function is useful when listening at low levels.Loudspeakers are ineffici ent at low power levels and will tend to sound flat.The loudness control will boost the bass and treble response thus giving a more lively performance. While this function is operating,the display shows LUD. 5. LCD DISPLAY -The liquid crystal display will display the current status of the unit. 6. BAND SELECTOR SWITCH Press this switch to select the desired Radio band.Selection is made in regular sequence as FM-AM. 7. AUTOMATIC OR MANUAL TUNING(FREQ UP>>OR FREQ DOWN<<) (A) RADIO MODE When pressed for less than 1 second,these keys operate as manual tuning mode. When pressed longer than 1 sec.,they are operated as SEEK tuning mode.(AUTO) (B) CD PLAYER MODE When pressed for less than 1 second,these keys operate as TRACK UP or TRACK DOWN. When pressed longer than 1 sec.,they will operate as CUE or REVIEW mode. -- 2 -- -- 3 -- REMOVING THE FRONT PANEL CD CONTROL LOCATION OF PARTS 17 19 18 Front Panel LUD C D / C D - R / C D - R W PLAYE R LUD Release Button PUSH SEL DISP RPT RDM SCAN ALL DIR SONG CLASSIC BND JAZZ MUT CLK MUSIC MUTE LOUD MONO AF PTY EON ST LOC LUD INSTALLING THE FRONT PANEL 60 WATT/DIGITAL TUNING SYSTEM SCN A/PS 1 LUD 2INT 3RPT 4RDM 5 6 MODE 20 21 22 23 17.CD EJECT BUTTON Press the EJECT button to remove the CD.The receiver will automatically switch to radio mode. 18.CD SLOT 19.TRACK/SEARCH BUTTON FORWARD AND REVERSE TRACK SEARCH Press the SKIP button or during play to go to the desired track(song). ( ....REVERSE)( ....FORWARD) Press and hold the SKIP button or during play to scan the disc at high speed.When the desired music section of the disc is found,release the button.Normal play will resume. 20.PAUSE BUTTON During PLAY ,press button to PAUSE.Press it again to resume play. 21.INT BUTTON (Priview all Tracks) This feature allowes you to listen to the first 10 seconds of each track on the display .Press the key SCAN indicator appears on the LCD pannel. To cancel the function press the key again. 22.REPEAT BUTTON (RPT) To repeat the current track press the key.The RPT indicator appears on the LCD panel and the track be repeated continuously. To cancel the function press the key again. 23.RANDOM BUTTON (RDM) Press the key. Tracks will be player in randomorder. To cancel the function the press the key again. PRECAUTIONS Do not touch the contacts on the front panel or on the unit body, since this may result in poor electrical conductivety.If dirt or other foreign substances get on the contacts, wiper them with a clean dry cloth. PRECAUTIONS WHEN HANDLING THE FRONT PANEL Do not leave the front panel in any area exposed to high temperatures or direct sunlight. Do not drop the front panel or otherwise subject it to strong impact. Do not allow such volatile agents as benzene, thinner, or insecticides to come into contactwith the surface of the front panel. Never try to disassemble the front panel. INSTALLATION NOTE: Choose the mounting location where the unit will not interfere with normal driving function. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop. Like an emergency stop. If installation angle exceeds 30 from horizontal the unit might not give optimum performance. Avoid installating the unit where it would be subject to high temperature.such as from direct sunlight. Lower case or from hot air,from the heater,or where it would be subect to dust,.dirt or excessive vibration. HOW TO REMOVE AND INSTALL THE FRONT PANEL 1. 2. Press the release button and pull-off the front panel. To install the front panel, insert the panel into the housing and make sure the panel is securely installed, otherwise, abnormalities occurs on the display or some keys will not function properly. DIN FRONT/REAR-MOUNT This unit be can properly installed either from Front (conventional DIN Front-mount) or Rear (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For detail, refer to the following illustrated installation methods. -- 4 --- 5 -- DIN FRONT- MOUNT (Method A) Installing the unit USING THE RESET BUTTON 1. Dashboard 2. Holder After inserting the holder into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place. 3. Screw Press button with a thin, pointed object if unit is malfonctioning. Though not a normal occurrence, the microprocessor which controls the operation of this unit can be affected by electrostatic noise. This generally is indicated by such symptoms as no power being supplied when you switch the unit on, failure of buttons and controls, or an abnormal display. Should this happen, press the reset button with a thin, pointed object to reset the microprocessor. 1 2 3 1 6 7 4 2 3 5 1. 2. 3. 4. 5. 6. 7. Dashboard N ut (5mm) Spring washer Screw (5 x 16mm) Screw Strap B sure to use the strap to secure the e b ack of the unit of the place. The strap c an be bent by hand to the desired angle. Plain washer FLASHING RESET SPECIFICATIONS MW(AM) SECTION 1. 2. 1 3. 3 Frame I sert fingers into the groove in the front n of frame and pull out to remove the frame .(When re-attaching the frame. Point the side with a groove downwards and attach it.) Lever In sert the levers supplied with the unit in to the grooves at both sides of the unit a shown in figure until they click. s P ulling the levers makes it possible to re move the unit from the dashboard. Frequency Range Channel Step Intermediate Frequency Usable Sensitivity Image Rejection Ratio If Rejection Ratio FM SECTION Frequency Range Channel Step Intermediate Frequency Image Rejection Ratio at 106KHz Signal to noise ratio CD PLAYER SECTION : 530 - 1710 KHz : 10 KHz : 450 KHz : 33 dB : >50 dB : >50 dB 4 SPEAKER WIRING CONNECTIONS ANTENNA RED(R) BLACK GROUND(-) BLUE AUTO ANT(+) RED B (+) YELLOW BACK UP : 87.5-107.9 MHz : 200 Khz : 10.7 MHz : >50 dB : >60 dB LINE OUT WHITE(L) RED(R) GRAY FUSE 0.5A 1A Signal to noise Radio Channel separation Frequency Response : More than 60dB : More than 60dB : 20Hz - 20KHz LINE IN WHITE(L) BLACK 7A GRAY + GRAY/BLACKVIOLET + VIOLET/BLACK- FRONT LEFT SPEAKER REAR LEFT SPEAKER + WHITE - WHITE/BLACK + GREEN/BLACK - GREEN FRONT RIGHT SPEAKER REAR RIGHT SPEAKER GENERAL Power Supply Voltage Speaker impedance Maximum Output Power Dimensions Chassis -- 7 -: DC 12 Volts Negative Ground : 4 -8 : 15W x 4CH : 178(W) x 50 (H) x 160(D)mm -- 6 --