jWINSheriff V4.2 Operation Manual Introduction 2 System Feature jWINSheriff V4.2 provides advanced digital technology that supercedes old-fashioned CCTV monitoring and VCR systems. It allows 'instant replay' and simultaneous recording. jWINSheriff V4.2 also provides security personnel to define 'security events' that require recording compression of non-event periods into a few frames of video for continuity. This eliminates long hours of tape review and allows you to quickly find any date, time or alarm by random access. System Requirements This chart reflects the minimum system requirements to operate V4.2 ONE Card OS CPU Expansion Slot System Memory Video Memory Main board Hard Disc Space DirectX For Remote View Windows98SE or Higher Pentium II 400MHz or Higher 1 PCI Slot 128MB or More 16MB or More IBM PC Compatible 10GB or More Version 8.0 or Higher Modem or Network Card TWO CARDS Windows98SE or Higher Pentium III 700MHz or Higher 2 PCI Slot 256MB or More 32MB or More (ATI Series) Intel845, SiS645 Series or Higher 20GB or More Version 8.0 or Higher Modem or Network Card jWINSheriff. In case of using above two card, Program might do not work according to the specification of Main board or VGA adapter. 3 Installing jWINSheriff Board 1) Turn off power on the computer. * It is very important to turn the computer's power before you open the case. Static Electricity can provide a big enough shock to damage the components of your PC. NEED TO EXPLAIN ABOUT PROPER GROUNDING BEFORE TOUCHING ANY COMPONENTS. 2) Open computer case and Please install as follows: 3) Check to make sure there is a PCI slot available. AGP (VGA) Slot PCI Slot ISA Slot < PCI slot > 4) Please install securely in the slot. < PCI slot Installation > 5) Secure the card in place by tightening the screw. 6) Close the case then turn on the computer 4 Install System Video Out A User may connect CCTV camera, video phone, or video out port of any security system to one of camera input ports on GVC capture card. Also, a user may use TV out to connect an external analog CCTV monitor. 5 Install Software 1) After installed jWINSheriff Board, and turn on your computer, automatically display as below "Found New Hardware Wizard" program. At that time, click all of "Cancel" button, and finished Wizard program. (according to a type of board and quantity of board, can be repeated.) 2) To install jWINSheriff V4.2 software, You must insert `the installation CD' in your CD-ROM drive. 3) Then, the installation program will run automatically. (If not, run 'Autorun.exe' file) 6 4) Select "Install Recorder". 5) Before installation takes place, a dialog box will ask whether it should install with driver. If you selected "Yes", it will install the jWINSheriff program with driver (The Driver is jWINSheriff on your needed to run this program. If this is your first installation of Computer, you must select "Yes") 6) And then Installing device driver. 7) According to indicating the install program, click "Next" program. 8) Reboot computer, if you had done installation successfully. The program icon will appear on window of your desktop. jWINSheriff warning! jWINSheriff uses a specific data format. So, you must designate the specific data file by using the setup program's 'Storage Space' section after installation. jWINSheriff will not record data without specific jWINSheriff storage space. 7 Main Screen Overview Screen Mode Minimize/ Close Channel Rotation PTZ Control PTZ Speed Control PTZ Extension Video & Audio Recording Status Setup Local Viewer Power Warning Digital Out Local Viewer: Run Local Viewer[Search] Setup : Run Setup Minimize/Close : Hide Button DVR Recorder in tray bar, and Close Button[Exit] Video & Audio Recording Status : Status of Recording about Video and Audio Warning: Display Warning Message Screen Mode : Division of Display Screen [1,1/4,2/4,3/4,4/4,1/9,10/9,16,etc..] Channel Rotation: Automatically Changing Channel PTZ Control: PTZ basic button PTZ Speed Control: Slide bar for PTZ moving speed PTZ Extension: Button about expending PTZ control panel Digital Out Switch: Switch button about Digital-out on Capture board Exit: Exit Button 8 SETUP 9 Preset ID and Password The preset ID is set in "Administrator," Password is set in "Admin." Setup Tree General - Display Device - Video Input Signal - Communication Setup(WebCam Server) - PTZ Setup - Save Image Quality - Font - Use Full screen mode - Check Daily Reboot - Use Password - User Add/Delete - Windows Shell mode - Site Name Sensor / Alarm Setup Camera / Motion Detection - Camera Setup - Motion Setup - Overlay Setup - PTZ Receiver Setup Audio Setup Schedule Setup Holiday / Recording Frame - Holiday Registration - Event Recording Setup - Motion recording Setup - On Time recording Setup - Sensor recording Setup Storage Space ETC - Using Line Monitor - Using Alert Mode - Notify E-mail 10 Display Device Basically, jWINSheriff support DirectX, but the graphic card of your computer sometimes do not support above DirectX and YUV Overlay. In this case, you must set up "Display Device" to "RGB Device" (The default value is "RGB Device".) Video Input Signal jWINSheriff support both of Video signal NTSC and PAL type. In NTSC, maximum recording speed is 30 fps, in PAL TYPE; maximum recording speed is 25fps on each channel. 11 Setup the communication 1) Using TCP/IP - Check "Use TCP/IP" in Check box. 12 2) Using Dynamic IP by DHCP of ADSL, Cable modem. - First, verify the network connection and Internet connection is working. - Check "Use TCP/IP" in Check box. - Click "Web registration." - Click "Register Web server" -> Pop-up window will appear. - Key in "www.inetdvr.com" in "Web server" - In "Site Name" key in a characteristics name instead of IP address. 3) Using in network behind Firewall or internal IP. To set the Port settings, Select TCP/IP (default value 911 for Video, 912 for Audio), You must notify it to your network manager for these changes. (Please inquiry details to your network manager.) 13 4) Using Serial Device - Check "Use Serial Device" in check box. - Set up communication port and transfer rate. 14 5) Using PSTN (Public Subscriber Telephone Network) Dialup Modem. - Check "Use serial device" in check box. - Check "In Modem device." - Click "Find Modem" or set up communication port. - Set up "Baud rate" WebCam Server 1) Using a WebCam Server Even if you have no client program at the remote site you can watch images to using a web browser. Check "Web Cam Server" for this function. 15 The value of default port is 80, but the user can change the value of the default port. If there is no display of the image due to the firewall. (The remote user can connect the webcam server to the recorder without the network administrator authorization. Note: For broadband T1 and Dial up Connection The user sets up the frame rate according to the communication speed of the on line connection. The maximum number of frames that can be viewed is 30fps. The higher the fps the more CPU resources will be needed from the server. Therefore, the user can adjust the fps speed of upload from 1fps for PSTN Dial-up modem or less than 300Kbps, 2fps for 512Kbps and 30fps for 10Mbps on the basis of 4 channels. If you used WebAgent when you changed Web Server Port, WebAgent should be reinstalled. 2) Viewer When the user is monitoring the image through web browser, the user must set up the IP address of the server and port number, through the WebCam Sever set up port. If WebCam Server set up default port, that is Web server port, so you could insert just IP Address on web browser. For example, enter "http://192.168.10.99" or "http://192.168.10.99/html/index.html" on the location window of the web browser. 16 PTZ (Pan Tilt Zoom) Set up communication port for control PTZ, transfer rate, parity. The PTZ Receiver uses RS-485 communication protocol, and you can reserve that port for DVR capture board. "COM1" or "COM2", can only be used for (RS-232C) protocol. jWINSheriff supports setting each PTZ Receiver by different ID number (in tab "Set up Camera") Save Image Quality jWINSheriff supports MJPEG and MPEG4 algorism. MJPEG, provides higher image quality, While MPEG4 provides a higher compression rate. When selecting MPEG4, you must to set Key Frame term. 17 Font Set up User can change font of camera name. Full Screen Mode If there is no keyboard or mouse movement within a 60 second period the screen will automatically be changed to the full screen mode. Daily Reboot Feature When the daily reboot function is checked, the system will automatically reboot itself at the prescribed time. When systems are running for long periods of time they tend to accumulate very large memory files which can cause the system to freeze up. This feature is very useful for assigning dates and times to automatically reboot the system. Use Password Only authorized person can use the set-up page to change contents or shut the down. Default User ID/Password is "Administrator/Admin", "Anonymous/Guest" It's necessary to set authorizations for other User ID's operation and Remote Access. Specially, "Anonymous/Guest" is important when you used WebCam Server. When you accessed Webcam server, the Server will be start to find "anonymous". If the User ID is existed, the Server is checked channel which camera channels are shown by server setup. Otherwise, If there is no ID:Anonymous (ex, ID:Anonymous was Erased), every camera is not able to access by anyone. 18 User Add/Del To register new user, click "User Add/Del" button, and then click "Add new user". Insert new ID and Password about new user. In user authority, "allow multiple Access" have the function that multi user can do simultaneous access. However, supervisor is not permitted multiple accesses (Person that have authority of run/end, set up it.) 19 Window Shell Mode If you wanted to use your computer for DVR, Check this box. If you checked this, after computer rebooting, Only DVR runs on your computer without any application. Site Name This system window with "Site Name" to distinguish another DVR's from remote client Program. (This is same with site name of "register Web Server" in "Set up communication".) 20 Sensor/Alarm This section defines the sensor/alarm action. jWINSheriff supports 2 type of Sensor/alarm action. "x": If sensor works, record those images according to schedule. From above "x," click right mouse, you can use extension functions (Preset, Light On, User Operation). When PTZ was supported, "P1 ~ P16": When sensor works, camera operates to preset location. "L": When sensor works, turn on light. "U": This function controls the Aux 5 of PTZ Controller from user operation. As above, only PTZ controller is supported. If not so, and you use to alarm control in DVR Board, you can click alarm number connected with sensor number. You can set up one Sensor/alarms or sensors/ an alarm. 21 You can set NC (Normal Close), NO (Normal Open) and Alarm out duration. Digital out is worked by event on schedule, during how long time you set. It's not worked when you switched digital out. For setup NC, NO Click Sensor number For setup alarm out duration Click D/O channel number 22 Set up camera connection and resolution jWINSheriff program can identify camera signal automatically though the camera connected. When you do not see images (because of camera broken, disconnection of a cable), "Video loss" will occur at local or remote monitoring center. The recording resolution is supported by 320X240, 640X240, 640X480 on NTSC, 384*288, 768*288, 768*576 on PAL. "Don't display" is a function that will not display on Screen, but will continue to record on the DVR. jWINSheriff 23 Camera/Motion Detection To set up the Motion detection area, click and drag the left mouse button. To cancel the area, click and drag the right mouse button. Clicking on the "Detection sensitivity" button, you can control the sensitivity of Motion Detection. Also if you couldn't notify Motion detection area very well, you can change the color of Motion detection area to other color by clicking "Change detecting point" 24 Set up overlay (Advanced Model) If you use Overlay board (GVC-16R), you must set up brightness, color, etc. of Overlay board in addition 25 Set up types of PTZ Receiver You can set up different types PTZ receivers. 26 Set up Audio This function is a part that set voice sensitivity compounding camera. User can set up camera and audio environment to use audio. Click camera #1 button Setting audio, Icon of speaker shaped come out in lower column part. "Audio setting": Lower button is better quality, but file size is getting bigger and bigger. "Recording method": Always recording audio: If you can not click this button, audio will be recorded only when motion detection works. After connecting a microphone, press "Audio test" button, you can see yellow pulse signal. If i ...