CD PLAYER DP-R7090 DP-R6090 INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is used for two models. Model availability and features (functions) may differ depending on the country and sales area. COMPACT DIGITAL AUDIO B60-3245-00 MA ( T, M ) I D 98/12 11 10 9 8 7 6 5 4 3 2 1 97/12 11 10 9 8 7 6 5 Introduction DP-R7090/R6090 (En) 2 Before applying power Units are designed for operation as follows. Caution : Read this section carefully to ensure safe operation. U.S.A. and Canada ................................................................ AC 120 V only Australia .................................................................................. AC 240 V only Europe and U.K. ..................................................................... AC 230 V only China ......................................................................................... AC 220 V only *Other countries ............................ AC 110-120 / 220-240 V switchable AC voltage selector switch *AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. AC110-220V AC220-240V LINE OUTPUT VARIABLE L SYSTEM CONTROL DIGITAL OUTPUT COAXIAL OPTICAL SL16 XS 8 R TEXT AC110-220V AC220-240V Note: Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch. Move switch lever to match your line voltage with a small screwdriver or other pointed tool. For the United Kingdom Factory fitted moulded mains plug 1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse. 2. The fuse cover must be refitted when replacing the fuse in the moulded plug. 3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live Do not connect those leads to the earth terminal of a three-pin plug. Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Caution : Read this section carefully to ensure safe operation. WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. The marking of products using lasers (Except for some areas) REQUIREMENT BY NEDERLAND GAZETTE Batteries are supplied with this product. When they empty, you should not throw away. Instead, hand them in as small chemical waste. CLASS 1 LASER PRODUCT The marking is located on the rear panel and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. DP-R7090/R6090 (En) Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future. Keep this manual handy for future reference. 3 Special features CD-TEXT support ¶ The text information (disc title, track titles, names of the artists, songwriters, composers, etc.) recorded on the CDs can be easily called and displayed in alphanumerics. (Some @# Japanese words and text may not be displayed.) ¶ D.R.I.V.E. (Dynamic Resolution Intensive Vector Enhancement) IC is built in for drastic reduction of distortion at small signal level. ¶ High-performance new D/A converter achieving a 24-bit resolution. (DP-R7090 only) ¶ Edit function for rearranging tracks according to the tape length so that no music is interrupted in the middle. * ¶ Auto space function. % ¶ Easy operation functions allow systematic operation with other KENWOOD components connected through the system control connection. 6 Advanced technologies incorporated in pursuit of improved sound quality and stability Convenient features for dubbing CD onto tape Easy operation functions Accessories Audio cord ........................ (1) System control cord ............ (1) AC plug adaptor .............. (1) Remote control unit ......... (1) REMOTE CONTROL UNIT Batteries (R6/AA) .............. (2) Contents RC-P0601 Use to adapt the plug on the power cord to the shape of the wall outlet. (Accessory only for regions where use is necessary.) Caution: Read the pages marked carefully to ensure safe operation. Introduction .................................................................. 2 Before applying power ................................................ 2 Safety precautions ....................................................... 2 Special features ................................................................... 3 Searching for tracks by title (TITLE SEARCH) ......... 12 Displays ...................................................................... 13 Programmed play (PGM mode) ................................ 14 To check or change the programmed tracks .................. 15 To add a track to the program ......................................... 15 To clear tracks from the program .................................... 15 System connections .................................................... 4 Connection to a general-use amplifier .............................. 5 Connection to digital amplifier or MD ............................... 5 Adjusting the output levels of the output jacks and headphone output ............................................................... 5 To use the headphone ......................................................... 5 Repeated playback .................................................... 16 To repeat only the programmed tracks ........................... 16 To repeat the entire disc ................................................... 17 Editing ......................................................................... 18 To check the edited contents ........................................... 19 Playing or recording the edited contents ....................... 19 To clear the edited contents ............................................. 19 Controls and indicators ............................................... 7 Operation of remote control unit ............................... 8 Preparing to play tracks .............................................. 9 Normal play (TRACK mode) ...................................... 10 Playing tracks in order from track No.1 .......................... 10 Playback from desired track ............................................. 11 Skipping tracks .................................................................. 11 Searching ........................................................................... 11 Playback in random order (Random playback) ....... 20 Timer operations ........................................................ 21 Maintenance ............................................................... 22 In case of difficulty ..................................................... 23 Specifications ............................................................. 24 System connections DP-R7090/R6090 (En) 4 Caution: Do not plug in the power lead until all connections are completed. Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Malfunction of microcomputer If operation is not possible or erroneous display appears even though all connections have been made properly, reset the £ microcomputer referring to "In case of difficulty". Caution regarding placement To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below. Left and right panels: 10 cm Rear panel: 10 cm 75 coaxial cable with RCA PIN. (Commercially-available) Commercially-available optical fiber cable SL 16/XS8 switch 6 Digital component (MD, DAT, etc.) (COAXIAL) DIGITAL INPUT (OPTICAL) LINE OUTPUT VARIABLE L SYSTEM CONTROL DIGITAL OUTPUT COAXIAL OPTICAL SL16 XS 8 R TEXT AC110-220V AC220-240V To AC outlet Remove the protection cap when using the DIGITAL OUTPUT (OPTICAL) jack. Commercially-available optical fiber cable SYSTEM CONTROL DIGITAL INPUT OPTICAL System control cord Digital amplifier (or ordinary amplifier, receiver, etc.) CD L Audio cord R To wall AC outlet Notes 1. Connect all cords firmly. If connections are loose there could be loss of sound or noise produced. 2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit. DP-R7090/R6090 (En) 5 Connection to a general-use amplifier Use the provided audio cords to connect the OUTPUT jacks of this unit to the CD input jacks (or AUX jacks) of the amplifier. Connection to digital amplifier or MD Connect the DIGITAL OUTPUT (OPTICAL or COAXIAL) jack to the digital input jack of the amplifier, DAT recorder, MD recorder, etc., using an optical fiber cable or coaxial cable which are commercially available in audio stores. ÷ When using an optical fiber cable to connect this unit to a digital amplifier, insert the plug straight into the jack until a snap sound is heard. ÷ Be careful not to bend, coil, or bundle the optical fiber cable. ÷ Optical fiber cables available on the market may not always be able to be used with this player. If your cord cannot be used with this unit, consult the store from which you purchased the cord or your nearest dealer. Optical fiber cable Adjusting the output levels of the output jacks and headphone output The OUTPUT level (UP/DOWN) keys of the remote control unit can adjust the output levels from the LINE/OUT and PHONES jacks of the unit. To use the headphone Connect a stereo headphone to the PHONES jack of the CD player. Adjust the sound volume using the remote control unit. Output level OUTPUT -12dB OUTPUT DOWN UP REMOTE CONTROL UNIT RC-P0601 ÷ It is not favorable for the sound quality to decrease the output level from this unit too much. Use these keys for coordination with other line levels. ÷ Adjusting the headphone output level also changes the LINE/OUT level. Do not adjust the output level from this unit particularly during recording. ÷ Please note that the sound output is at the maximum level when the power is turned on. DP-R7090/R6090 (En) 6 SYSTEM CONTROL CONNECTIONS Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below. [XS8] Mode : lets you combine F, f, and terminals [SL16] Mode : for terminals only This unit is compatible with both [XS8] and [SL16] modes. Select the mode according to the connected components. 4 Amplifier or receiver SYSTEM CONTROL SYSTEM CONTROL This unit j SYSTEM CONTROL Cassette deck SL16 XS 8 ÷ Do this operation after completing all connections. (Ensure that the unit is set to STANDBY mode.) Notes 1. If your amplifier or receiver does not have a system control terminal, do not connect any system control cords to the system control terminals on the other components. 2. Do not connect system control cords t ...