User manual LASERLINE 921K

OPERATING INSTRUCTIONS SELF-LEARNING PROCEDURE EMERGENCY CODE (PIN CODE) DISPLAY PROCEDURE To display the PIN CODE, activate the self-learning procedure and wait 10 seconds for the LED to switch OFF. The immobiliser will use the LED for displaying 5 sequences of flashes that will correspond to 5 numbers. The following table shows an example of a PIN CODE and the corresponding LED flashes: LASERLINE model 921K immobiliser is a sophisticated electronic device for vehicle protection, which ensures very reliable protection with a simple operation procedure.The system consists of a control unit, LED/Receptacle and two code keys. The 921K immobiliser deactivates the main electric circuits of the vehicle (starter solenoid, petrol pump, injection or ignition coil...) and simply operates by a coded key that must be touched to a receptacle on the vehicle fascia before starting the vehicle. Activation of the system is automatically carried out approximately 20 seconds after switching the ignition off. Once activated, a dash fascia mounted LED will flash. From now on, the immobiliser operates on two specific points of the vehicles starting-ignition or fuel supply systems, to prevent an unauthorised attempt to start the vehicle. To switch the immobiliser off, touch the coded key into the receptacle and remove. You have approximately 20 seconds to start the vehicle. If you fail to start the vehicle within this 20 seconds the system will re-activate automatically and it will be necessary to re-touch the coded key to the receptacle in order to start the vehicle. Note: always switch OFF the immobiliser before switching ON the ignition key as accidental activation of Self-Learning Procedure may occur. If accidental activation of Self-Learning Procedure does occur, wait for LED to flash at a rate of 1 flash per 2 seconds before disarming. All the wires of the immobiliser are black and are recognisable by a code printed on the end of them. When the installation is completed, all the codes on the ends of the wires are removed so that they are not identifiable and the immobiliser cannot be neutralised. There are thousands of millions of combinations for the coded keys, so each key is unique and cannot be replicated. When one of the 2 supplied coded keys is lost, it is necessary to execute the SELF-LEARNING PROCEDURE. 1 ) Deactivate the immobiliser by inserting a CODED KEY into the receptacle. 2) Turn ignition key to ON position. 3) Insert and hold one of the CODED KEYS into the receptacle. 4) Maintaining the CODED KEY into the receptacle, turn OFF the ignition key. 5) Remove the CODED KEY from the receptacle. For the numbers 5 6 0 5 4 n° of corresponding flashes n° 5 consecutive LED flashes n° 6 consecutive LED flashes n° 10 consecutive LED flashes n° 5 consecutive LED flashes n° 4 consecutive LED flashes 2 sec. Pause 2 sec. Pause 2 sec. Pause 2 sec. Pause 2 sec. Pause On the above example, the PIN CODE to note at the end of these instructions would be 5 6 0 5 4. 6) Check if the LED is steady ON, as indication of the beginning of SELF-LEARNING PROCEDURE. 7 ) Within 10 secods of the LED remaining ON, insert into the receptacle a new/spare CODED KEY, followed by the original CODED KEY first used to enter the SELF-LEARNING PROCEDURE. Each KEY learning is signalled by a short pause of the LED 8 ) When the 10 seconds from the last CODED KEY as elapsed, the immobiliser exits from the SELFLEARNING PROCEDURE and displays the EMERGENCY CODE (PIN CODE) via flashing of the LED. 9) Note the PIN CODE in the space provided at the end of these instructions. Verify that all CODED KEYS operate; otherwise, repeat the above steps. It is imperative to note on a piece of paper this Emergency Pin Code, if it is different from the original pin code displayed in the rear of these instructions. This pin code must then be stored in a secure location. Note: If you intend to leave these instructions in the vehicle, the pin code in the back of these instructions should be removed for safekeeping. This emergency code is derived from the first CODED KEY memorised when you self-learn a new CODED KEY. If you want to change the pin code from the original code, you may have to follow the self-learning procedure more than once alternating the first CODED KEY until a new pin code is given. HOW TO DISARM THE IMMOBILISER USING THE "EMERGENCY CODE" If the CODED KEYS do not work correctly or have been lost, to disarm the immobiliser you must insert the "EMERGENCY CODE" (PIN CODE) as follows: 1) With the immobiliser ON, turn ON the ignition key. 2) The LED in the receptacle will now flash at a rate of 10 seconds ON, 2 seconds OFF, 10 seconds ON, 2 seconds OFF etc. 3) At any point when the LED is OFF, switch the ignition OFF. (If you miss the 2 second period whilst the LED is OFF the LED will again come on for 10 seconds). 4) The LED will start to flash and the immobiliser is ready to accept the PIN CODE. If not interrupted, the LED will flash 10 times. Turn ON the ignition key for 1 second after the LED as displayed the flashes corresponding to each digit of your PIN CODE, read PIN CODE at the end of these instructions from left to right. For a better understanding, see the example. If the inserted PIN CODE is correct, the immobiliser will disarm itself and automatically enter the "SELFLEARNING PROCEDURE", signaling this condition by LED ON for 10". Follow SELF-LEARNING PROCEDURE from step 6. If the inserted PIN CODE is wrong, the immobiliser will remain ON. Note After the above operations, any lost or stolen CODED KEYS become useless. Code memorisation can only occur when the LED located in the receptacle is constantly on. No more than 10 seconds must elapse between memorising each CODED KEY. When 4 CODED KEY have been memorised, the immobiliser will automatically exit from the self-learning procedure or 10 seconds after the last CODED KEY was memorised. If a new CODED KEY has been memorised, it is necessary to memorise the original CODED KEYS if their continued use is desired. If only one CODED KEY is available no SELF-LEARNING PROCEDURE will take place and the procedure will enter EMERGENCY CODE (PIN CODE) DISPLAY PROCEDURE. To memorise only one CODED KEY follow the "USING THE EMERGENCY CODE (PIN CODE) TO DISARM THE IMMOBILISER" procedure and memorise single CODE KEY. LIFETIME WARRANTY Product warranty covers units to be free from defects in manufacture for the lifetime ownership of the original vehicle, in accordance with the terms and conditions of this warranty document. Any product, which is deemed to be defective, will be replaced or repaired. Accessories including remote controls, touch keys and additional modules are guaranteed for a period of 12 months from date of installation. Terms and Conditions 1. Product must be installed by an authorised qualified installer. 2. If product is transferred by an authorised installer onto another vehicle then in this case the warranty reverts back to 2 years from the date of the original installation. 3. Warranty is not transferable by the original customer to other owners of the product accessory. 4. The customer must complete and return the warranty registration document within 21 days from date of purchase in order for the warranty to be valid. 5. The warranty covers product only and not the quality of the installation. The warranty for installation is provided by the installer. We cannot be held responsible for costs arising due to incorrect installation. 6. All warranty claims must be directed through the original installer, accompanied by the original invoice, detailing date of installation and annual service record. Failure to do this will render the warranty invalid. 7. Continuance of product warranty is subject to an annual product service check for which a small charge may be levied by any authorised installer. Evidence of service check record must be provided in support of warranty claims. 8. Warranty does not cover costs incurred for breakdown assistance or vehicle recovery, due to product or accessory failure. Warranty does not extend to reimbursement for damage due to defects in products or accessories. Exclusions from Warranty Warranty will not be valid due to the following: Poor response to transmitters due to abnormally high electromagnetic interference. Low battery voltage in transmitters. Abuse or mistreatment of any product or accessory. Loss or damage due to accident, fire, lightening, explosion, flood or water, war or civil disturbances. Damage caused by external electrical source or from abnormal variation or failure of power supply. Failure caused by installation of accessories not approved by the product manufacturer. Failure of product occurring outside Great Britain. Replacement of defective parts within the guarantee period does not include consumable parts or include labour. 9. If product is repaired by a non authorised installer the product will cease to be covered by the warranty. 10. Original manufacturer negligence. 1. 2. 3. 4. 5. 6. 7. 8. Consumer Details All warranties are limited to the duration of this warranty. This is the complete warranty and no other express or implied warranty is valid. Nothing in this warranty shall affect your statutory rights. TURN ON THE IGNITION FOR 1 SEC. 1 2 3 4 5 6 7 8 9 10 2" PAUSE TURN ON THE IGNITION FOR 1 SEC. 1 2 3 4 5 6 7 8 9 10 2" PAUSE TURN ON THE IGNITION FOR 1 SEC. 1 2 3 4 5 6 7 8 9 10 ® 2" PAUSE TURN ON THE IGNITION FOR 1 SEC. CAR ALARM SYSTEMS GB 1 2 3 4 5 6 7 8 9 10 2" PAUSE TURN ON THE IGNITION FOR 1 SEC. 1 2 3 4 5 6 7 8 9 10 2" PAUSE CODE ? CORRECT IMMOBILISER DEACTIVATED INCORRECT IMMOBILISER STILL ACTIVATED EXAMPLE: the code to be inserted is 5 6 0 5 4. First digit 5 - Wait 5 flashes for the first digit. After the fifth flash has been completed and the LED has turned OFF, immediately turn ON the ignition key for 1". Turn the ignition OFF and after a pause, the LED will flash for the next digit of the PIN CODE; Second digit 6 Wait 6 flashes for the second digit. After the sixth flash has been completed and the LED has turned OFF, immediately turn ON the ignition key for 1". Turn the ignition OFF and after a pause, the LED will flash for the next digit of the PIN CODE; Third digits 0 - For the 0 digit, the flashes to be completed on the LED are 10. Continue until all the digits have been displayed and inputted correctly. USER MANUAL IMMOBILISER MODEL 921K YOUR PIN CODED IS: IMMOBILISER WITH ELECTRONIC KEY FOR ALL CARS WITH 12V NEGATIVE EARTH ELECTRICAL SYSTEMS NOTE Manufacturer declines any responsibility for damage of the immobiliser and the vehicle electrical system due to WRONG INSTALLATION OR TAMPERING. LASERLINE SpA RESERVES THE RIGHT TO EFFECT CHANGES OF THE PRODUCT WITHOUT FURTHER NOTICE. TEST APPROVAL NUMBERS MIRRC Reference Number: TE2 - 1188/1100 Category 2 WE ADVISE YOU TO CHOOSE AN ACCREDITATED INSTALLER. THE SYSTEM MUST BE FITTED FOLLOWING THE SUPPLIED INSTRUCTIONS; ANY ALTERATION OR ADDITION TO THE SYSTEM OR INSTALLATION CAN INVALIDATE THE CERTIFICATE OF INSTALLATION. TECHNICAL DATA POWER SUPPLY: ....................................................................................................................................... 12VDC CURRENTDRAW: ................................................................................................................................................. 1 m .A 5 REARMING DELAY: ............................................................................................................................. 20 seconds RELAYS CONTACT CAPACITY (continuous): ................................................................................................... 20 A Our commissioned Sales and Support Agents in the UK are LSp Agencies 33,Craven Court - Winwick Quay Warrington - Cheshire WA2 8QU Phone Number 01925 406300 (Sale support) cod.: is UT921K FILENAME: ISUT921K.P65