Contents Introduction Warning Caution Main Unit Description Remote Control OSD basic adjustment DTV Features USB/CARD Reader Operation Specifications Trouble Shooting 1 Introduction Thank you very much for your purchase of our product of LCD TV. It serves as a normal color TV and PC monitor. To enjoy your set to the full from the very beginning, read this manual carefully and keep it handy for ready reference. INSTALLATION Locate the receiver in the room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Allow enough space between the receiver and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure. This TV receiver can be connected to AC100-240V 50/60HZ. Do not install the receiver in a location near heat sources such as radiator, air ducts, direct sunlight, or in a place somewhere like close compartment and close area. Do not cover the ventilation openings when using the set. The indicator light will last about 30 seconds to go out after cutting off the electricity, during this period, you cannot repower it on until the indicator light goes out, thanks a lot for your attention! 2 Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to avoid the risk of electric shock, do not disassemble this equipment by anyone except a qualified service personnel. This symbol is intended to alert the user to the presence of important operation and maintenance instructions in the literature accompanying the equipment. 3 Caution Caution High voltages are used in the operation of this product. Do not remove the back cabinet from your set. Refer servicing to qualified service personnel. Caution To prevent fire or electrical shock hazard, Do not expose the main unit to moisture. Caution Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver. Caution Avoid exposing the main unit to direct sunlight and other source of the heat. Do not stand the television receiver directly on other produces which give off heat. E. g. video cassette players, Audio amplifiers. Do not block the ventilation holes in the back cover. Ventilation is essential to prevent failure of electrical component. Do not squash power supply cord under the main unit. 4 Caution Caution Never stand on, lean on, push suddenly the product or its stand. You should pay special attention to children. Caution Do not place the main unit on an unstable cart stand, shelf or table. Serious injury to an individual, and damage to the television, may result if it should fall. Caution When the product is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet. Caution The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks. 5 Main unit description Control Panel Button Function VOL+ : Volume up. VOL- : Volume down. CH+ : TV channel up. CH- : TV channel down. MENU : Press to select the main menu. TV/AV : Select the input signal. POWER : Switch on when at standby mode or enter the standby mode. TV Terminal Connections 1 .USB input terminal. 2. HDMI input terminal. 3. VGA input terminal of simulation signal of PC. 4. PC AUDIO terminal. 5. SCART input terminal. 6. Video input terminal. 7. AUDIO input terminal. 8. ATV antenna/close circuit TV network port or DTV antenna port. 9. HEADPHONE output terminal. Power Input Configuration AC POWER 6 Optional Configuration as below: Connect the USB/CARD storage to the USB/CARD jack on the set. NOTE It is only 500 mA MAX of DC current output when you connect with USB jack or CARD socket. To ensure the Mobile HD works well, you should use other power supply for the Mobile HD. And do not use the USB jack and CARD socket in the same time. It supports Mobile HD by connecting with USB jack. The partitions of the Mobile HD can't be more than 4 partitions. The max partition is 2TB. It supports FAT/FAT32 document. The max FAT document is 4GB and the max FAT32 document is 2TB. 7 Remote control POWER: Press this button to switch on the TV when at standby mode or enter standby mode. MUTE: Press this button to mute or restore sound. NICAM/A2: In the TV condition, press this key to select the sound effects. SLEEP: Set the sleep timer. ASPECT: Press to select the different picture size. USB/CR: Press to select the MEDIA signal source. (Used for models with USB/CR function only) DISPLAY: Display TV information . AUTO: Press to adjust the picture automatically in PC mode. PMODE: Select picture mode. SMODE: Select sound mode. DTV: Press to enter the DTV channel. (Used for models with DTV function only) SOURCE: Press to change signal source. ENTER: Enter the selected option or perform the selected operation. MENU: Press this button to enter the main menu for various optional adjustable setting. EXIT: Exit the OSD (On-screen display). 0-9: Select and switch to a channel using 0 - 9. -/--: Switch the program digit. : Switch back and front between the current and previous channels. CH-/CH+: Change the channel up and down. VOL-/VOL+: Adjust the volume. INFO: Display some information of current program in DTV mode. (Used for models with DTV function only) AUDIO: Press to select the DTV audio. (Used for models with DTV function only) FAV: Switch between custom set " Favourite List" (Used for models with DTV function only) TV/RADIO: Switch between DTV program and radio program (only audio but not image). (Used for models with DTV function only) 8 EPG: Enter electronic program guide. (Used for models with DTV function only) Stop playing the MEDIA or stop to record. (Used for models with USB/CR function only) SUBTITLE: Open or close subtitle. (Used for models with DTV function only) TEXT: Press to enter the Teletext mode. (Used for European region only) Press to start playing the MEDIA or to pause playing. (Used for models with USB/CR function only) HOLD: Freeze a multi-page passage on screen in Teletext mode. (Used for European region only) : Start to record. INDEX: Press this button to go to the index page in Teletext. (Used for European region only) Press to play backward. (Used for models with USB/CR function only) SIZE: Display the top, bottom or all of page to read easily in Teletext mode. (Used for European region only) Press to play forward. (Used for models with USB/CR function only) REVEAL: Press this button to reveal the hidden information in Teletext page. Press again to hide the information. (Used for European region only) Skip to previous chapter (Used for models with USB/CR function only) SUBPAGE: Carry out the function of SUBCODE in the text while enter the text display mode. (Used for European region only) Skip to next chapter (Used for models with USB/CR function only) RED,GREEN,YELLOW, CYAN: Correpond to the different colored subjects. (Used for european region and USB/CR function only) 9 OSD basic adjustment Picture You can select the type of picture, which best corresponds to your viewing. 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "PICTURE" menu. Enter the "PICTURE" menu by pressing " " button. 2. Press " / " button to select "PICTURE MODE" and press the " / " button to select the picture mode . 3. Press " / " button to select "BRIGHTNESS" and press the " / " button to enter brightness adjustment menu to adjust brightness. 4. Press " / " button to select "CONTRAST" and press the " / " button to enter contrast adjustment menu to adjust contrast. 5. Press " / " button to select "SATURATION" and press the " / " button to enter color adjustment menu to adjust saturation. 6. Press " / " button to select "SHARPNESS" and press the " / " button to enter sharpness adjustment menu to adjust sharpness. 7. Press " / " button to select "HUE" and press the " / " button to enter hue adjustment menu to adjust hue. Note: The item hue is only for NTSC 8. Press " / " button to select "COLOR TEMP" menu and press the " / " button to select the color temp. Sound You can select the type of sound, which best corresponds to your listening. 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "SOUND" menu. Enter the "SOUND" menu by pressing " " button . 2. Press " / " button to select "SOUND MODE" and press the " / " button to select the sound mode . 3. Press " / " button to select "BASS" and press the " / " button to enter bass adjustment menu to adjust bass. 4. Press " / " button to select "TREBLE" and press the " / " button to enter treble adjustment menu to adjust treble. 10 5. 6. Press " / " button to select "BALANCE" and press the " / " button to enter balance adjustment menu to adjust balance. Press " / " button to select "AVL" and press the " / "button to select the avl function on or off. FUNCTION You can make the desired adjustment in the TV mode. 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "FUNCTION" menu. Enter the "FUNCTION" menu by pressing " " button . 2. Press " / " button to select "LANGUAGE" menu and press the " / " button to select the OSD language which you desire. 3. Press " / " button to select "OSD DURATION" and press the " / " button to select the time how long you want OSD display. 4. Press " / " button to select "ASPECT RATIO" menu and press the " / " button to select the size which you desire. 5. Press " / " button to select "TT LANGUAGE" menu and press the " / " button to select the local TELETEXT LANGUAGE. 6. Press " / " button to select "BLUE SCREEN" and press the " / "button to select the blue background on or off. 7. Press " / " button to select "RESET", then press "ENTER" button to enter. Press the " / " button to select "YES" or "NO". ATV 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "ATV" menu. Enter the "ATV" menu by pressing " " button. 2. Press " / " button to select "AREA" and press the " / " button to select the local country. 11 3. Press " / " button to select "AUTO SEARCH" and press the "ENTER" button to enter. Press " / " button to select "YES" or "NO". 4. Press " / " button to select "MANUAL SEARCH" and press the "ENTER" button to enter. a. CHANNEL Press " / " button to select "CHANNEL" and press the " / " button to select the different channel . b. COLOR SYSTEM Press " / " button to select "COLOR SYSTEM" and press the " / " button to select the local color system . c. SOUND SYSTEM Press " / " button to select "SOUND SYSTEM" and press the " / " button to select the local sound system . d. FINE TUNE Press " / " button to select "FINE TUNE" and press the " / " button to select the frequency which you want to fine tune . e. SKIP Press " / " button to select "SKIP" and press the " / "button to select skip the channel on or off. f. MANUAL SEARCH Press " / " button to select "MANUAL SEARCH" and press the " / " button to adjust the channel's frequency . 5. Press " / " button to select "CHANNEL EDIT" and press the "ENTER" button to enter. a. Press " / " button to select one channel and press "RED" button to pitch on. Press " / " button to select another channel which you want to swap . Press "ENTER" button to confirm. b. Press " / " button to select one channel and press "GREEN" button to pitch on. Press " / " button to select another channel which you want to insert . Press "ENTER" button to confirm. c. Press " / " button to select one channel and press "YELLOW" button to pitch on. Press " / " button to select another channel which you want to copy. Press "ENTER" button to confirm. d. Press " / " button to select the channel which you want to delete and press "CYAN" button to pitch on. Press "ENTER" button to confirm. 12 e. Press " / " button to select the channel in the list, press "ENTER" button to enter the rename channel's window. Input channel name at "____", press "/ / " button to select "letter", "number", "_", "", "", "EMPTY" or "BAK SPC", and press "ENTER" button to confirm. Press " / / " button to select "OK" to save and return to the previous menu. Press " / / " button to select "CANCEL" to exit and return to the previous menu. PC 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "PC" menu. Enter the "PC" menu by pressing " " button. 2. Press " / " button to select "H POSITION" menu and press the " / " button to enter "H Position" adjustment menu to adjust "H Position". 3. Press " / " button to select "V POSITION" and pre ...