User manual LEXIBOOK ST5

Introduction English English Congratulations! You have just purchased a Lexibook® Universal 5 in 1 Remote Control. Compatible with over 3000 brands of audio-visual product, this universal remote control combines the functions of several remotes: TV, Video Recorder (VCR), Satellite (SAT), DVD and Auxiliary (AV). Caution: Before its first use, you must set up the remote control so that it functions with your chosen audio-visual products. To do so, please read these instructions carefully. 2. If you have problems programming or using the remote control: · · · Check whether the remote control is pointing directly at the appliance and that there are no obstacles between the remote control and the appliance. Check whether you are pressing the correct button for the Television, VCR, Satellite or DVD player for your choice of appliance. Check whether your appliance is designed to receive a remote infrared signal. 2. 3. 4. 5. 6. Press the Press the Press the OFF. key and Device key (TV, VCR, SAT etc.) which you key again, the indicator light will flash. once at a time (setup counter up) until the equipment turns want to control at the same time, then the indicator light will turn on. The LED keeps flashing. Try different keys on your remote control for the equipment you wish to control. If you manage to control it, press the appropriate key for that equipment (TV, VCR, SAT, etc.), indicator should flash and turn off to indicate that the code is accepted. Warranty This product is covered by our two-year guarantee. For all matters relating to the guarantee or our after-sales service, please contact your retailer and have your receipt on hand. Our guarantee covers manufacturing or assembly defects with the exception of all damage resulting from a failure to respect the instructions, or any inappropriate handling of the article (such as taking it apart, exposing it to heat or humidity, etc). Freephone customer service: 0808 100 3015 Customer service address: Wolfe Lodge, Bordon, Hants GU35 ONH Website: www.lexibook.com Required programming procedure 7. There are two programming modes: manual and automatic programming. To programme manually, use the code specific to the manufacturer or brand of the appliance (4-digit code). Automatic programming is used when the specific codes are unknown. 1. Manual Setting 1. Look up the four-digit code for your brand and type of equipment in the code tables on the following pages. 2. Press the key and Device key which you want to control at the same time, then the indicator light will turn on. 3. Press the four-digit code for your equipment. Each time LED blink one time. If the LED turn off, it indicates that the code is accepted. 4. 5. If the LED blink 2 times and then on, it indicates that the code is wrong. If the first code in the list for your appliance do not work, try every code one after the other for your appliance. You need exit the set ting modes and restart the process. If these codes does not work, try setting Auto Scan procedure (automatic programming). Note: 1. If no key on your remote is pressed for 10 seconds, the programming process will stop automatically, and you will have to start over. 2. Exit the setting mode: Press any device key in the setting process. LED turnoff. 4. 1. 2. If you do not manage to control your equipment, restart the procedure from step 4. Note: 1. 2. 3. If no key on your remote is pressed for 30 seconds, the programming process will stop automatically, and you will have to start over. If the LED indicator is off on the setting mode, it stands for stop the setting mode. If the code is not match with your equipment, then repeat step 1 to 6. key, the power 3. Power Scan Concepts 1. During the power scan mode, if you press and hold code data is transmitted continuously. 2. 3. During the power scan mode, if you press and release , the power code data is transmitted on time in reverse direction. During the power scan mode, if you press and release Device key, the current code data is selected. Select the device key in TV-added (TV, VCR, SAT, etc...). Press 5 times. and Digital 1. LED will be flashing. The flashing time is stand for 1st digit of the selected code. E.g.: Code=5476, Led will be flashing How to test the selected code? 3. Press 4 times. Press 7 times. and Digit 2, LED will be flashing. The flashing time is stand for the 2nd digit of the selected code. E.g.: Code=5476, Led will be flashing 4. and Digit 3, LED will be flashing. The flashing time is stand Note: · The programming mode cancels out if you press buttons other than the digits. · Try the remote control. If it does not work properly, try to programme it with other codes. · If your television has a video function (combined television/video) you must programme it by pressing the VCR button on the remote control. Copyright © Lexibook 2004 1 for the 3rd digit of the selected code. E.g.: Code=5476, Led will be flashing 5. 6. Press and Digit 4, LED will be flashing. The flashing time is stand for the 4th digit of the selected code. E.g.: Code 5476, Led will be flashing 6 times. If LED will not be flashing, it stands for number 0. 2 Copyright © Lexibook 2004 3 Copyright © Lexibook 2004 English Quick Power Scan (Auto Find) Setting 1. Turn on the equipment you want the remote to control (TV, VCR, SAT , etc.), and point the remote toward it. Troubleshooting