User manual LG 23LC1RB

LCD TV OWNER'S MANUAL MODEL: 23LC1R* Internet Home Page : http://www.lge.com http://www.lg.ca ENERGYSATR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. P/NO : 38289U0024C (0605-REV00) Printed in Korea Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. U.S.A. only ----------------------------------------------COMPLIANCE: The responsible party for this product's compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-800-243-0000 http://us.lge.com --------------------------------------------------------------2 Safety Instructions Safety Instructions WARNING : To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. Ow ner's Man ual 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 11. Only use the attachments / accessories specified by the manufacturer. 3 Safety Instructions Safety Instructions continued 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. Note - If the TV feels cold to the touch, there may be a small "flicker" when when it is turned on. This is normal, there is nothing wrong with TV. - Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. - Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 4 Contents Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . .3~4 Sound Menu Options EZ Audio . . . . . . . . . . . . . . . . Equalizer Adjustments . . . . . . AVL (Auto Volume Leveler) . . Sound Balance . . . . . . . . . . . Stereo/SAP Broadcasts Setup Time Menu Options Auto Clock Setup . . . . . . . . . Manual Clock Setup . . . . . . . On/Off Timer Setup . . . . . . . Sleep Timer Setup . . . . . . . . Auto Off . . . . . . . . . . . . . . . . Special Menu Options Closed Captions . . . . . . . . . . Caption/Text . . . . . . . . . . . . . Captions . . . . . . . . . . . . . . . . Key Lock . . . . . . . . . . . . . . . . Lock Menu Options . . . . . . . . Lock Menu Setup . . . . . . . . . Power indicator . . . . . . . . . . . PC Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 .21 .21 .22 .22 .23 .23 .24 .24 .24 .25 .26 .26 .27 .28 .29 .29 .30 Introduction Controls . . . . . . . . . . . . . . . . . . . . . . .6 Connection Options . . . . . . . . . . . . . . .7 Remote Control Key Functions . . . . . .8 Installation Accessories . . . . . . . . . . . . . . . . . . . .9 Kensington Security System . . . . . . . .9 Installation Instruction . . . . . . . . . . . . . .10 Please set it up carefully so the product doesn't fall over . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 External Equipment Connections . .13~16 Antenna Connection . . . . . . . . . . . . .13 VCR Setup . . . . . . . . . . . . . . . . . . . .14 Cable TV Setup . . . . . . . . . . . . . . . . .14 External A/V Source Setup . . . . . . . .15 DVD Setup . . . . . . . . . . . . . . . . . . . .15 DTV Setup . . . . . . . . . . . . . . . . . . . .16 Using Headphones . . . . . . . . . . . . . .16 PC Setup . . . . . . . . . . . . . . . . . . . . .16 Maintenance . . . . . . . . . . . . . . . . . . . . . . . .31 Troubleshooting Checklist . . . . . . . . . . . . .32 Operation TV Operation Overview . . . . . . . . . . . Menu Language Selection . . . . . . . . . Channel Menu Options Memorizing the Channels with EZ Scan . Add/Delete Channels with Manual Program . . . . . . . . . . . . . . . . . . . . . Favorite Channels Setup . . . . . . . . . Picture Menu Options EZ Video . . . . . . . . . . . . . . . . . . . . . Manual Picture Control( User option) Picture format(ARC) . . . . . . . . . . . . .17 .17 .18 .18 .19 .20 .20 .20 Product Specifications . . . . . . . . . . . . . . . .34 After reading this manual, keep it handy for future reference. 5 Introduction Introduction Controls CH VOL ENTER MENU INPUT /I On/Off Button Enter Input Button Volume Button Channel Buttons Menu Buttons Button Remote Control Sensor Power/Standby Indicator Glows amber in Standby mode, Glows blue when the TV is turned on. 6 Introduction Connection Options VIDEO IN2 VIDEO VIDEO INPUT L/MONO AUDIO AUDIO INPUT ANTENNA PC SOUND INPUT PC INPUT JACK INPUT COMPONENT (DTV/DVD IN) AUDIO AC IN PC INPUT R ANT IN ( 75 ) PC SOUND H/P VIDEO IN1 S-VIDEO AC INPUT COMPONENT (DTV/DVD IN) ((480i/480p/720p/1080i), Audio) AUDIO/VIDEO INPUT S-VIDEO INPUT HEADPHONE JACK 7 Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the TV. MUTE Switches the sound on or off. TV Returns to the TV mode. INPUT Selects: TV, Video1, Video2, S-Video, Component or PC input sources. POWER MTS (Refer to p.22) MENU ENTER INPUT TV Video1 Video2 S-Video Component PC D E  MENU FAV (Refer to p.19) EXIT NUMBER buttons CH D / E (Channel button) VOL F / G (Volume button) AUDIO (Refer to p.21) CC (Refer to p.26) ARC (Refer to p.20) VIDEO (Refer to p.20) SLEEP (Refer to p.24) FLASHBK Press the FLASHBK button to return to the last channel you were watching. Installing Batteries · Open the battery compartment cover on the back side and insert the batteries with correct polarity. · Use two 1.5V batteries of AAA type. Don't mix used batteries with new batteries. 8 Installation Installation Accessories Owner's Manual AAA Batteries Remote Control Power Cord Tie Holder - Arrange the wires with the tie Holder. D-sub cable (PC) Audio cable (PC) 2-TV Bracket Bolts 1-TV Bracket, 2-Wall Bracket Installation guide Rack 4-Anchor 4-Screws for wall mount rack Fixing screw Kensington Security System - The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For the detailed installation and use of the Kensington Security System, refer to the user's guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors. NOTE - The Kensington Security System is an optional accessory. NOTES a. If the TV feels cold to the touch, there may be a small "flicker" when when it is turned on. This is normal, there is nothing wrong with TV. b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. 9 Installation Installation Instruction Unfolding the stand base 1. Place the set with its front facing downward on a cushion or soft cloth. 2. Hold down the release button inside the stand and strongly pull out the stand with your two hands. Note: Here shown may be somewhat different from your set. The stand won't move if you don't press release button. Wall Mount: Horizontal installation 4 inches 4 inches 4 inches 4 inches 4 inches For proper ventilation, allow a clearance of 4" on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. Desktop Pedestal Installation 4 inches 4 inches 4 inches 4 inches For proper ventilation, allow a clearance of 4" on each side and from the wall. 10 Installation Installation Instruction Continued Connection of TV 1. Connect the aerial cable to the socket marked +75 on the back. For the best reception an outdoor aerial should be used. 2. To connect an additional equipment, see the External Equipment Connections section. 3. Connect the power cord. Note: Here shown may be somewhat different from your set. ( ) Positioning your display Adjust the position of the panel in various ways for maximum comfort. · Tilt range 12 Be careful that your hands are not pressed down when tilting the screen. 11 Installation Please set it up carefully so the product doesn't fall over Set it up close to the wall so the product doesn't fall over when it is pushed backwards. The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the product doesn't fall over when it is pulled in the forward direction. It will prevent the product from falling forward and hurting people. It will also prevent the product from damage caused by fall. Please make sure that children don't climb on or hang from the product. Accessories / 2-TV Bracket Bolts 1-TV Bracket, 2-Wall Bracket The Product Back Side The Product Back Side 1 3 2 1. Use the bracket and the bolt to fix the product to the wall as shown in the picture. 2. Secure the bracket with the bolt (not provided as parts of the product, must purchase separately) on the wall. 3. Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. Notes · When moving the product to another place undo the ropes first. · Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. · To use the product safely make sure that the height of the bracket that is mounted on the wall is same as that of the product. 12 Installation External Equipment Connections Antenna Connection - For optimum picture quality, adjust antenna direction. Connecting to an Inside Antenna Setup - Typical wall antenna jack used in apartment buildings, connect the antenna cable as shown below. (Use the correct type of antenna cable for the type of wall antenna jack.) Turn clockwise to tighten. 75 Round Cable 300 Flat Wire Antenna Converter Copper Wire UT ANT IN ( 75 ) Apartment Buildings Wall Connection Jack Antenna Jack - If you have a 75 round cable, insert the bronze wire and then tighten the connection nut. If you have a 300 flat wire, connect the twisted wire to the antenna converter and then connect the converter to the antenna jack on the TV. - If using 75 round cable, do not bend the bronze wire. It may cause poor picture quality. Connecting to an Outdoor Antenna Setup - This type of antenna is commonly used in single family dwellings. VHF Antenna Turn clockwise to tighten. UHF Antenna UT ANT IN ( 75 ) 75 Round Cable 300 Flat Wire Copper Wire Single Family Home Antenna Converter Antenna Jack - In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown to the right. - If signal needs to be split for two TVs, use an antenna signal splitter for connection. VHF UHF NPUT ANT IN ( 75 Signal Amplifier 13 Installation External Equipment Connections Continued VCR Setup - In Video mode, TV automatically reverts to TV mode if the TV buttons are pressed. COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P Connection 1 Set VCR switch to 3 or 4 and then tune TV to the same channel number. VIDEO IN1 S-VIDEO Connection 2 1. Connect the audio/video output jacks on VCR to the corresponding input jacks on the TV. When connecting the TV to a VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual.) 3. Use the INPUT button on the remote control to select Video1. - If connected to S-VIDEO on rear panel, select the S-Video external input source. Typical Antennas ANT IN 2 1 S-VIDEO OUT ANT OUT Direct Connection CH3 IN CH4 VCR VIDEO (R) AUDIO (L) COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P VIDEO IN1 S-VIDEO Typical Antennas ANT IN 2 1 S-VIDEO OUT IN CH4 ANT OUT Direct Connection CH3 VCR VIDEO (R) AUDIO (L) Cable TV Setup - After subscribing to a local cable TV service and installing a converter, you can watch cable TV programming. - For further cable TV information, contact a local cable service provider. Connection 1 1. Select 3 or 4 with channel switch on cable box. 2. Tune the TV channel to the same selected output channel of cable box. 3. Select channels at the cable box or with the cable box remote control. COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P Connection 2 1. Connect the audio/video output jacks on Cable Box to the corresponding input jacks on the TV. When connecting the TV to Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). 2. Use the INPUT button on the remote control to select Video1. 3. Select channels with the cable box remote control. VIDEO IN1 S-VIDEO 2 1 (R) AUDIO (L) TV VCR VIDEO RF Cable Cable Box 14 Installation External A/V Source Setup Connections Connect the audio/video output jacks on the external A/V equipment to the corresponding input jacks on the TV. When connecting the TV to external A/V equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P VIDEO IN1 S-VIDEO Camcorder Viewing Setup 1. Turn on the external A/V equipment. 2. Use the INPUT button on the remote control to select Video1 or Video 2. 3. Operate the corresponding external equipment. Refer to external equipment operating guide. External Equipment side panel Video Game set R AUDIO L VIDEO VIDEO IN2 VIDEO AUDIO R L/MONO Camcorder DVD Setup External Equipment Video Game set R AUDIO L VIDEO Connections 1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) jacks and connect the DVD audio outputs to the AUDIO jacks. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV. NOTE: If your DVD player does not have component video output, use S-Video. Viewing Setup 1. Turn on the DVD player, insert a DVD. 2. Use the INPUT button on the remote control to select Component. 3. Refer to the DVD player's manual for operating instructions. (If connected to S-VIDEO on rear panel, select the S-Video external input source.) COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P VIDEO IN1 S-VIDEO · Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports of the TV Video output ports of DVD player Y Y Y Y Y PB PR Y PB PR (R) AUDIO (L) DVD Pr Pb B-Y R-Y Cb Cr PB PR 15 Installation DTV Setup - To watch digitally broadcast programs, purchase and connect a digital set-top box. COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P VIDEO IN1 S-VIDEO Connections Connect the digital set-top box video outputs to the COMPONENT (Y, PB, PR) jacks and connect the digital set-top box audio outputs to the AUDIO jacks. Y PB PR (R) AUDIO (L) Viewing Setup 1. Turn on the digital set-top box. (Refer to the owner's manual for the digital set-top box.) 2. Use the INPUT button on the remote control to select Component. DTV Receiver (Set-top Box) Using Headphones - Plug headphones in to H/P jack as shown. - Adjust sound level to a headphone using the volume (F, G) buttons. While you are listening to sound through a headphone(s), TV speakers will not be heard. ANT IN ( 75 ) PC SOUND H/P S-VIDEO PC Setup - After setup, be sure to select PC source on TV. Connections 1. Set the monitor output resolution on the PC before connecting to the TV. 2. Connect the TV to the PC with the PC cable. 3. Connect the PC audio output to the TV's PC SOUND input. Viewing Setup 1. Turn on the PC. 2. Use the INPUT button on the remote control to select PC. Monitor Display Specifications MODE Resolution VGA SVGA XGA WXGA WXGA 640x480 800x600 1024x768 1280x768 1360x768 Horizontal Vertical Frequency(kHz) Frequency(Hz) 31.4 37.8 48.3 47.7 47.6 60 60 60 60 60 COMPONENT (DTV/DVD IN) AUDIO PC INPUT ANT IN ( 75 ) PC SOUND H/P VIDEO IN1 S-VIDEO NOTES a. For optimum picture quality, use standard 1360x768@60Hz computer output at a 60Hz refresh rate . Using other formats (VGA, SVGA, etc.) or refresh rates may result in reduced picture quality. (To change the computer video output format, please refer to the operating manual for the computer you are using). b. If the message "Out of range" appears on the screen, adjust the PC output to a format listed in the `Monitor Display Specifications' chart above. c. The synchronization input form for Horizontal and Vertical frequencies is separate. DPM (Display Power Management) mode If the PC goes to power saving mode, the monitor automatically switches to DPM mode. If you don't use the PC cable provided, DPM mode may not work. 16 Operation Operation TV Operation Overview 1. First, make all equipment connections. Plug the AC Adapter into the TV, then plug the AC Adapter into a power outlet. At this time, the TV is switched to standby mode. · In standby mode, press the POWER, TV, CH (D,E), INPUT or number button on the remote control or r / I, CH (D,E), INPUT button located on the TV to turn the TV on. 2. Select the viewing source by pressing INPUT. · Note: See page 18 if you have not auto programmed the TV to receive channels in your local broadcast area. 3. After viewing, press the POWER button on the remote control or r / I button located on the TV. The TV reverts to standby mode. NOTE · If you want to turn the TV off, press the on/off button located on the TV. If you intend to be away on vacation, disconnect the power plug from the wall power outlet. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use 2. Press the G button and then use D / E D / E button to select the Special menu. button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. 4. Press the ENTER button to save. 17 Operation Channel Menu Options Memorizing the Channels with EZ scan - For Auto program to work, the programming source must be connected to the TV and the TV must be receiving programming signals either over-the-air or from a cable-type service provider. 1. Press the MENU button and then use D the Channel menu. 2. Press the G button and then use EZ Scan. /E button to select Channel EZ Scan Manual prog. Favorite ch. To start D /E button to select 3. Press the G button to begin the channel search. · Wait for auto program to complete the channel search cycle before choosing a channel. The TV scans for over-the-air channels and then channels provided by a cable service. D FG E  MENU NOTES · When the channel search is complete, use the D / E buttons to review the memorized channels. · If you press the ENTER button in auto programming, the function will stop and only channels programming up to that time will remain. · Auto program function can memorize only the channels which are being received at that time. Add/Delete Channels with Manual Program - You can manually include or erase individual channels. The current channel number is displayed. 1. Press the MENU button and then use D Channel menu. 2. Press the G /E button to select the button to select Channel EZ Scan Manual prog. Favorite ch. TV Memory 30 button and then use D /E Manual prog. 3. Press the G button and then use F / G button to select a channel you want to add to memory or erase. 4. Press the E button and then use F /G button to select Memory (add) or Erase (delete). D FG E  MENU 5. Press the ENTER button to save. The current channel is added to Memory or Erased from the channel list. 18 Operation Favorite Channels Setup - Favorite Channel lets you quickly tune in up to 8 channels of your choice without having to wait for the TV to scan through all the in-between channels. Channel EZ Scan Manual prog. Favorite ch. Favorite Ch. ----------------------------------------------------------------D FG E To set  MENU EXIT D FG E  MENU 1. Press the MENU button and then use 2. Press the G button and then use 3. Press the G button and then use D /E button to select the Channel menu. D /E D /E button to select Favorite ch.. button to select the first favorite channel position. 4. Use the F / G button to set the desired channel number for first favorite channel. 5. Repeat steps 3 to 4 to memorize other channels. 6. Press the ENTER button to save. · To tune to a favorite channel, press the FAV button repeatedly. The 8 favorite channels appear on the screen one-by-one. 19 Operation Picture Menu Options EZ V ideo - This function adjusts the TV for the best picture appearance. 1. Press the VIDEO button repeatedly to select the picture appearance setup option as shown below. Clear Optimum Soft User · You can also adjust EZ Video in the Picture menu. · Clear, Optimum and Soft are preset for good picture quality at the factory and cannot be changed. Manual Picture Control (User option) ( - You can adjust picture contrast, brightness, color, sharpness and tint to the levels you prefer. 1. Press the MENU button and then use D Picture menu. /E button to select the 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, Tint). Picture EZ Video Contrast Brightness Color Sharpness Tint Contrast 85 to make appropriate adjustments. · Contrast, Brightness, Color, and Sharpness are adjustable from 0 to 100. · Tint is adjustable from - 50 to + 50. 4. Press the ENTER button to save. 3. Use the F / G button D FG E  MENU Picture format (ARC) - You can watch TV in various picture formats; 16:9, Zoom, 4:3. Repeatedly press the ARC button to select your desired picture format. · 16:9 You can enjoy the cinema (the picture format of 16:9) or general TV programme through the 16:9 mode. The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full. · Zoom You can enjoy the cinema in a vast screen through the Zoom mode. The screen 4:3 is magnified to the upper / lower and left / right sides so that the screen 16:9 is full. The bottom and top of the picture may be lost. · 4:3 This picture format is 4 to 3 of general TV. NOTES Zoom is not available in PC mode. 20 Operation Sound Menu Options EZ Audio - This function lets you enjoy the best sound without any special adjustment because the TV selects the appropriate sound option based on the program content. 1. Use the AUDIO button to select the appropriate sound setup as shown below. Flat Music Movie Sports User · You can also adjust EZ Audio in the Sound menu. Equalizer Adjustments Sound EZ Audio AVL Balance Flat Music Movie Sports User G 0.1 0.5 FG D FG E 1 D E 5 10 KHz  Move Adjust Exit  MENU 1.Press the MENU button and then use D 2. Press the G button and then use 3. Press the G button and then use D /E D /E /E button to select the Sound menu. button to select EZ Audio. button to select User. 4. Press the G button and then use F / G button to select the band you want to adjust. Then, use D / E button to adjust the band level. 5. Press the ENTER button to save. AVL (Auto Volume Leveler) - AVL maintains an equal volume level automatically even if the channel is changed. 1.Press the MENU button and then use D the Sound menu. 2. Press the G button and then use D 3. Press the G button and then use On or Off. 4. Press the ENTER button to save. /E button to select to select A VL. Sound EZ Audio AVL Balance On Off / E button D /E button to to select D F E  MENU 21 Operation Sound Menu Options continued