User manual LG 32LX2D

LCD TV OWNER'S MANUAL MODELS: 26LX1D 32LX1D 26LX2D 32LX2D 32LP1D 37LP1D 42LP1D Internet Home Page : http://www.lge.com http://www.lg.ca Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. TM P/NO : 3828TUL309D (0503-REV01) Printed in Korea Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. U.S.A. only ----------------------------------------------COMPLIANCE: The responsible party for this product's compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-201-816-2000 http://www.lgusa.com --------------------------------------------------------------- 2 TV Guide On Screen Notices In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. Use of the CableCARD TradeMark. TM "CableCARD is a trademark of Cable Television Laboratories, Inc." TM Digital Cable Compatibility This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable operator enhanced program the TV Guide On Screen system, and data enhanced television service may require the use of a set top box. For more information contact your local cable operator. 3 Safety Instructions Safety Instructions WARNING : To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. Ow ner's Man ual 2. Keep these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 3. Heed all warnings. 4. Follow all instructions. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 11. Only use the attachments / accessories specified by the manufacturer. 4 Safety Instructions 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. Note - If the TV feels cold to the touch, there may be a small "flicker" when when it is turned on. This is normal, there is nothing wrong with TV. - Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. - Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 5 Contents Contents 2 3 Warnings TV Guide On Screen Notices / Digital Cable Compatibility Safety Instructions Accessories Controls (Model Name: 32/37/42LP1D) Connection Options (Model Name: 32/37/42LP1D) Controls (Model Name: 26/32LX1D, 26/32LX2D) Connection Options (Model Name: 26LX1D/2D) Connection Options (Model Name: 32LX1D/2D) Remote Control Key Functions Introduction 4~5 8 9 10 11 12 13 14~18 Installation Instruction 19 20 20 21 22~23 24~25 26~29 30 30 31 31 32~35 36~41 42~43 44~50 51~68 Various Installation How to use back cover Swivel Stand (32/37/42LP1D, 26/32LX2D only) Antenna or Cable Connection VCR Setup DVD Setup HDSTB Setup External AV Source Setup Digital Audio Output Monitor Out Setup (32LX1D/2D, 32/37/42LP1D only) TM CableCARD Setup PC Setup IEEE1394 TM G-LINK Setup TM TV Guide On Screen System Setup TM TV Guide On Screen System Feature Installation External Equipment Connections Basic operation 69 69 69 69 70 71 71 72 73 73 74 74 75 75 76 76 76 77 77 78 78 79 79 80 80 Turning on the TV Volume Adjustment Channel Selection On Screen Menus Language Selection On Screen Menus Selection and Adjustment EZ Scan (Channel Search) Manual Scan Channel Edit DTV Signal Strength Channel Label Setup Main Picture Source Selection Input Label EZ Picture APM (Adaptive Picture Mode) Manual Picture Control (EZ Picture-Custom option) Color Temperature Control Video Reset Audio Language EZ SoundRite EZ Sound Manual Sound Control (EZ Sound-Custom option) Stereo/SAP Broadcasts Setup Front Surround TV Speakers On/Off Setup BBE Setup Menu Options Operation 6 Video Menu Options Audio Menu Options Contents Time Menu Options 81 81 82 82 83 84 85 85 86 87 87 88 88 89~90 91 91 92 92 93 94 94 94 94 95 95 95 96 96 97 98 98 99 99 100 101 101 Auto Clock Setup Manual Clock Setup On/Off Timer Setup Sleep Timer Auto Off Aspect Ratio Control Cinema 3:2 Mode Setup Caption Caption/Text Caption Option Auto Demo (Review) Logo Light Freeze & Magnify (DTV/CADTV 720p or 1080i mode only) Parental Lock Setup Cable Menu Options Scrambled Channel Cable Channel List Emergency Alert Message Brief Info. Watching PIP/POP/Twin Picture Selecting an Input Signal Source for PIP/Twin Picture TV Program Selection for PIP Moving the PIP Sub Picture Adjusting Main and Sub Picture Sizes for Twin Picture Swapping the PIP/Twin Picture POP (Picture-out-of-Picture: Channel Scan) Notes on Memory card What is Memory Card Precaution for Using the Memory Card Insert/Eject Memory Card Supported Files Mode Basic Operation JPEG File Viewing Options Photo List OSD Display Picture Selection and Popup menu MP3 Files Playing Operation Music List OSD Display MP3 File Selection and Popup menu Screen Saver Option Menu Features Lock Menu Options Operation CableCARD Function TM Brief Info. PIP (Picture-inPicture)/POP/ Twin Picture 102~107 External Control Device Setup Reference 108~109 IR Codes 110 Programming the Remote 111~112 Programming Codes 113~114 Troubleshooting Checklist 115 115 Maintenance Product Specifications 7 Introduction Introduction Accessories Ensure that the following accessories are included with your TV. If any accessory is missing, please contact the dealer from where you purchased the product. Power Cord 75 Round Cable G-LINK Cable D-sub 15 pin cable TV UT INP TV W PO AU DIO ER D DV DE MO BLE EO /VID TV CA ME NU DA Y- VC R ST B Y+ DA TV R TE EN GU EX IT IDE 94 13 VO L TE MU V FA MA RK INF GE PA O i 1 GE PA 4 2 7 5 8 C H 3 P PI 6 0 ER M TI P SA CC FR EE ZE TO AU EZ C PI MO DE P PI CH P PI + CH AD JU ST EZ SO C M/ T EC EJ UN D M AP P PI AP SW O TI RA T PU IN 9 K HB AS FL 1.5V 1.5V Polishing Cloth Polish the screen with the cloth. Twister Holder Arrange the wires with the twister holder. Owner's Manual Remote Control / Batteries 8 Introduction Controls (Model Name: 32/37/42LP1D) - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. Logo Display Lamp 1394 IEEE Channel Display Power Standby Indicator Illuminates red when the TV is in standby mode. When the TV is switched on, blinks green and then illuminates green. DTV, CADTV mode TV, CATV, DTV, CADTV mode 1394 IEEE HDMI mode IEEE1394 Stereo mode mode Video1-2 mode Component1-2 mode Remote Control Sensor PC mode CH VOL MENU TV/VIDEO/ TV GUIDE R AUDIO L/MONO IN2 VIDEO ON/OFF S-VIDEO ON/OFF Button Memory Card Slot (For mode) TV GUIDE Button TV/VIDEO / CHANNEL (E, D) Button S-VIDEO Input Buttons MENU Button Audio/Video Input 2 VOLUME (F,G) Buttons 9 Introduction Connection Options (Model Name: 32/37/42LP1D) COMPONENT2 VIDEO COMPONENT2 (VIDEO / AUDIO Input) AUDIO L R AC IN G-LINK TM DIGITAL AUDIO OUTPUT / DVI INPUT / COMPONENT1 INPUT Port MONITOR OUT HDMI / IEEE1394 Port CableCARD TM AUDIO/VIDEO INPUT1 Slot HDMI CableCARD AC IN IEEE 1394 R AUDIO L (MONO) VIDEO G-LINK DIGITAL AUDIO (OPTICAL) OUTPUT S-VIDEO MONITOR OUT VIDEO1 CABLE REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT COMPONENT1 PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) COMPONENT1 INPUT R L ANTENNA VIDEO INPUT AUDIO INPUT RS-232C INPUT (CONTROL/SERVICE) / RGB INPUT (PC/DTV INPUT) PC AUDIO INPUT REMOTE CONTROL Port ANTENNA Input CABLE Input COMPONENT1 (VIDEO / AUDIO INPUT) * The HDMI port can receive video via High-Definition Multimedia Interface (HDMI) or the Digital Visual Interface (DVI). Note: An adapter or special cable is required to plug DVI into an HDMI port (available at home theater or computer stores). 10 Introduction Controls (Model Name: 26/32LX1D, 26/32LX2D) - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. Remote Control Sensor /Power Standby Indicator Illuminates red when the TV is in standby mode. When the TV is switched on, blinks green and then illuminates green. CH VOL MENU TV/ VIDEO/ TV GUIDE ON/OFF ON/OFF Button TV GUIDE Button TV/VIDEO / MENU Button VOLUME (F,G) Buttons CHANNEL (E, D) Button Buttons 11 Introduction Connection Options (Model Name: 26LX1D/2D) - Here shown may be somewhat different from your TV. S-VIDEO S-VIDEO VIDEO VIDEO2 Memory Card Slot (Form m m m mode) AUDIO Input (MONO) L R AUDIO VIDEO COMPONENT 2 COMPONENT2 (VIDEO Input) AC IN G-LINK TM DIGITAL AUDIO OUTPUT / DVI INPUT / COMPONENT1 INPUT Port AUDIO/VIDEO INPUT1 HDMI / IEEE1394 Port CableCARD TM Slot CableCARD AC IN HDMI IEEE 1394 AUDIO L (MONO) VIDEO S-VIDEO G-LINK OUTPUT DIGITAL AUDIO (OPTICAL) COMPONENT1 CABLE VIDEO1 VIDEO INPUT PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) COMPONENT1 INPUT AUDIO INPUT REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE PORT) DVI INPUT ANTENNA L R R RS-232C INPUT (CONTROL/SERVICE) / RGB INPUT (PC/DTV INPUT) PC AUDIO INPUT REMOTE CONTROL Port ANTENNA Input CABLE Input COMPONENT1 (VIDEO / AUDIO INPUT) * The HDMI port can receive video via High-Definition Multimedia Interface (HDMI) or the Digital Visual Interface (DVI). Note: An adapter or special cable is required to plug DVI into an HDMI port (available at home theater or computer stores). 12 VIDEO 2 Introduction Connection Options (Model Name: 32LX1D/2D) - Here shown may be somewhat different from your TV. S-VIDEO S-VIDEO VIDEO VIDEO2 Memory Card Slot (Form m m m mode) AUDIO Input (MONO) L R AUDIO TM AC IN G-LINK TM DIGITAL AUDIO OUTPUT / DVI INPUT / COMPONENT1 INPUT Port MONITOR OUT HDMI / IEEE1394 Port CableCARD Slot AUDIO/VIDEO INPUT1 HDMI CableCARD AC IN IEEE 1394 R AUDIO L (MONO) VIDEO G-LINK DIGITAL AUDIO (OPTICAL) OUTPUT S-VIDEO MONITOR OUT VIDEO1 CABLE REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT COMPONENT1 PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) COMPONENT1 INPUT R L ANTENNA VIDEO INPUT AUDIO INPUT RS-232C INPUT (CONTROL/SERVICE) / RGB INPUT (PC/DTV INPUT) PC AUDIO INPUT REMOTE CONTROL Port ANTENNA Input CABLE Input COMPONENT1 (VIDEO / AUDIO INPUT) * The HDMI port can receive video via High-Definition Multimedia Interface (HDMI) or the Digital Visual Interface (DVI). Note: An adapter or special cable is required to plug DVI into an HDMI port (available at home theater or computer stores). 13 VIDEO COMPONENT2 (VIDEO Input) COMPONENT 2 VIDEO 2 Introduction Remote Control Key Functions POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT Rotates the input mode between Antenna and Cable. In Video1-2, Component 1-2, RGB-DTV (or RGB-PC), HDMI/DVI, and IEEE1394 input sources, screen returns to the last TV channel. TV/VIDEO (Refer to p.17) External input modes rotate in regular sequence: Antenna, Cable, Video1-2, Component 1-2, RGB-DTV (or RGB-PC), HDMI/DVI). (Video 1-2, Component 1-2 input sources are linked automatically, Only if these are connected) E TV INPUT POWER TV/VIDEO TV AUDIO DVD MODE VCR STB CABLE DAY - DAY+ MENU TV GUID ENTER MODE Selects the remote operating mode: TV, VCR, DVD, CABLE, STB or AUDIO. EXIT 1394 MARK INFO i LIGHT Illuminates the remote control buttons. PAGE VOL MUTE FAV PAGE CH MENU Brings up the main menu to the screen. Enters or exits a Panel Menu in the TV Guide On Screen system. TV GUIDE Brings up the TV Guide On Screen system to the screen. 1 4 7 2 5 8 0 3 6 9 FLASHBK THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference. PIP TIMER SAP CC PIP CH- PIP CH+ PIP INPUT RATIO EZ PIC ADJUST APM SWAP EZ SOUND EXIT Clears all on-screen displays and returns to TV viewing from any menu. 1394 (Refer to p.36~41) Use it to operate the DVHS, MicroMV camcorder and DSTB. INFO (Refer to p.93) When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB and HDMI/DVI mode. FREEZE AUTO DEMO M/C EJECT NUMBER BUTTONS 14 Introduction VCR/DVD/DVHS/Camcorder BUTTONS Control some video cassette recorders or DVD players ("RECORD" button is not available for DVD player). Control DVHS or camcorders while in IEEE 1394 mode. DAY + / DAYMoves forward or backward in 24 hour increments. TV INPUT POWER TV/VIDEO TV AUDIO DVD MODE VCR STB CABLE Mode Control Buttons Controls the Mode. For further details, see the ` Enter to the Mode. Mode' section. DAY - DAY+ MENU TV GUID E MARK Selects a photo or music you want to view or play in M/C EJECT When removing the memory card, this button is used. mode. ENTER EXIT 1394 MARK INFO i PAGE VOLUME UP/DOWN Increases/decreases the sound level. CH VOL MUTE FAV PAGE CHANNEL UP/DOWN Selects available channels found with EZ scan and Manual scan. PAGE UP/DOWN Moves from one full set of screen information to the next one. MUTE (Refer to p.18) Switches the sound on or off. FAV Use to scroll the Favorite channels. 1 4 7 2 5 8 0 3 6 9 FLASHBK PIP TIMER SAP CC PIP CH- PIP CH+ PIP INPUT RATIO EZ PIC ADJUST APM SWAP EZ SOUND -- (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2,etc. FLASHBK Returns to the last channel viewed. FREEZE AUTO DEMO M/C EJECT TIMER (Refer to p.82) Lets you select the amount of time before your TV turns itself off automatically. RATIO (Refer to p.84) Changes the aspect ratio. ADJUST (Refer to p.35) Adjusts screen position, size, and phase in PC mode. 15 Introduction PAGE VOL MUTE FAV PAGE CH PIP (Refer to p.94) Switches between PIP, POP (Picture-out-of-Picture) and Twin picture modes. Switches the video window locking or unlocking in the Listings Grid. PIP CH-/PIP CH+ (Refer to p.94) Changes to next higher/lower PIP channel. 1 4 7 2 5 8 0 3 6 9 FLASHBK PIP INPUT (Refer to p.94) Selects the input source for the sub picture in PIP/Twin picture mode. SWAP (Refer to p.95) Exchanges the main/sub images in PIP/Twin picture mode. SAP (Refer to p.79) Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode. EZ PIC (Refer to p.75) Selects a factory preset picture mode depending on the viewing environment. APM (Refer to p.75) Concurrently, compare with the Daylight, Normal, Night Time and Custom on the screen. EZ SOUND (Refer to p.78) Selects the sound appropriate for the program's character. CC (Refer to p.86) Select a closed caption: Off, CC1~4, Text1~4. FREEZE Freezes the currently-viewed picture. Main picture is frozen in PIP/Twin picture mode. AUTO DEMO (Refer to p.87) Displays the slide show to explain the main features of this TV. PIP TIMER SAP CC PIP CH- PIP CH+ PIP INPUT RATIO EZ PIC ADJUST APM SWAP EZ SOUND FREEZE AUTO DEMO M/C EJECT Installing Batteries i.e) 1 2 3 16 Open the battery compartment cover on the back side. Insert two batteries in correct polarity (+ with +, - with -). Don't mix old or used batteries with new ones. TV INPUT POWER TV/VIDEO TV DVD MODE VCR STB AUDIO CABLE DAY - DAY+ MENU TV GUID E ENTER Close the cover. * Use a remote control 7 meter distance and 30 degree (left/right) within the receiving unit scope. * Dispose of used batteries in a recycle bin to prevent environment. Introduction