User manual LG DU-37LZ30

LCD Colour Television OWNER'S MANUAL MODELS: DU-30LZ30 DU-37LZ30 DU-42LZ30 Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. Internet Home Page : http://www.lge.com http://www.lg.ca P/NO : 3828TUL275D(0406-REV00) Printed in Korea Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. U.S.A. only ----------------------------------------------COMPLIANCE: The responsible party for this product's compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-201-816-2000 http://www.lgusa.com --------------------------------------------------------------- 2 Safety Instructions Safety Instructions WARNING : To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION : These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use the attachments / accessories specified by the manufacturer. 3 Safety Instructions Safety Instructions continued 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 4 Contents Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Introduction Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Connection Options . . . . . . . . . . . . . . . . . . . . . .7 Remote Control Key Functions . . . . . . . . . . . . . .8 Installation Installation Instruction . . . . . . . . . . . . . . . . . . . . . . .9 External Equipment Connections . . . . . . . . . .11~15 Antenna Connection . . . . . . . . . . . . . . . . . . . . .11 VCR Setup / Cable TV Setup . . . . . . . . . . . . . .12 External A/V Source Setup . . . . . . . . . . . . . . . .13 Monitor Out Setup / DVD Setup . . . . . . . . . . . .13 HDSTB Setup / Digital Audio Output . . . . . . . . .14 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Operation Screen Setup for PC mode Adjustments for screen position, clock, and phase Turning the TV On . . . . . . . . . . . . . . . . . . . . . . On-screen Menus Language Selection . . . . . . . Setup Menu Options EZ Scan (Channel Search) . . . . . . . . . . . . . . Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . DTV Signal Strength . . . . . . . . . . . . . . . . . . . Channel Label Setup . . . . . . . . . . . . . . . . . . Main Picture Source Selection . . . . . . . . . . . Front LED (Light Emitting Diode) Display . . . Video Menu Options EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Picture Control (User Option) . . . . . . XD Function . . . . . . . . . . . . . . . . . . . . . . . . . Color Temperature Control . . . . . . . . . . . . . . Video Preset . . . . . . . . . . . . . . . . . . . . . . . . Audio Menu Options Audio Language . . . . . . . . . . . . . . . . . . . . . . EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . Manual Sound Control (User Option) . . . . . . Stereo/SAP Broadcasts Setup . . . . . . . . . . . Front Surround . . . . . . . . . . . . . . . . . . . . . . . TV Speakers On/Off Setup . . . . . . . . . . . . . . . .16 . .17 . .17 . . . . . . . . . . . . . . . . . .18 .18 .19 .19 .20 .20 .21 .21 .21 .22 .22 .23 .23 .23 .24 .24 .24 Time Menu Options Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .25 Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .25 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .25 Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .26 Option Menu Features Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Caption / Caption Mode . . . . . . . . . . . . . . . . . .28 Caption Option / Cinema Mode Setup . . . . . . . .29 Demo (Review) . . . . . . . . . . . . . . . . . . . . . . . . .29 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Lock Menu Options Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .31 PIP (Picture-in-Picture)/Twin Picture Watching PIP/POP/Twin Picture . . . . . . . . . . . ..32 Selecting an Input Signal Source for PIP/Twin Picture . .32 Swapping PIP/POP/Twin Picture . . . . . . . . . . . .32 TV Program Selection for PIP . . . . . . . . . . . . . .32 Moving the PIP sub picture . . . . . . . . . . . . . . . .33 Adjusting Main and Sub Picture Sizes for Twin Picture . .33 POP (Picture-out-of-Picture: Channel Scan) . . .33 External Control Device Setup . . . . . . . . . . . . . . . .34~38 IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39~40 . . . . . . . . . . . . . . . . . . . . . .41 Programming the Remote Programming Codes . . . . . . . . . . . . . . . . . . . . . . .42~43 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .44 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .47 Setup and Operation Checklist Setup and Operation Checklist (See pages 11~15 for available connection and operational setup options.) 1. Unpack TV and all accessories. 2. Connect all external video and audio equipment. see pages 11 ~ 15. 3 Install batteries in remote control. See page 8. 4. Turn TV on. See page 17. 5. Turn video source equipment on. 6. Select viewing source for TV. See page 20. 7. Fine-tune source image and sound to your personal preference or as required by source. See pages 21 ~ 24. 8. Additional features set up See Contents above. After reading this manual, keep it handy for future reference. 5 Introduction Introduction - This is a simplified representation of front panel. Here shown may be somewhat different from your TV. - This manual explains the features available on the DU-42LZ30 TV. Front Panel Controls E CHANNEL (E, D) Buttons CH FG VOLUME (F,G) Buttons VOL ENTER Button MENU Button TV/VIDEO Button ON/OFF Button ENTER MENU TV VIDEO /I ON/OFF Remote Control Sensor Power Standby Indicator Illuminates brightly when the TV is in standby mode. Dims when the TV is switched on. 6 Introduction Connection Options - This manual explains the features available on the DU-42LZ30 TVs. Back Connection Panel S-VIDEO Input VIDEO Input AUDIO Input S-VIDEO IN2 R AUDIO L/MONO DVI INPUT (PC/DTV INPUT) Digital Audio Inputs (DVI, Component1)/ Digital Audio Output Remote Control Port Monitor Output DVI Input (PC/DTV Input) S-Video Input COMPONENT 2 DVI COMPONENT1 PC/DVI OUTPUT INPUT INPUT AUDIO INPUT DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 COMPONENT 1 (MONO) S-VIDEO VIDEO VIDEO Antenna1 Antenna 2 AC INPUT REMOTE CONTROL UPGRADE PORT DIGITAL AUDIO (OPTICAL) RGB INPUT (PC/DTV INPUT) R L R AUDIO L AUDIO INPUT VIDEO INPUT Upgrade Port RGB Input (PC/DTV Input) PC/DTV Audio Input Audio/Video Input 1 Antenna2 Input Antenna1 Input Power Cord Socket DVD/DTV Input (Component 1,2) * DU-30LZ30 DVI Input (PC/DTV Input) DVI INPUT (PC/DTV INPUT) 7 Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the TV. LIGHT Illuminates the remote control buttons. TV/VIDEO Selects: DTV, Analog, Video1-2, Component 1-2, RGB-DTV (or RGB-PC), DVI-DTV (or DVI-PC) input sources. LIGHT MODE MODE Selects the remote operating mode: TV, VCR, DVD, CABLE, HDSTB or AUDIO. Select other operating modes, for the remote to operate external devices. POWER COMP/RGB/DVI Selects: Component 1-2, RGB-DTV (or RGBPC), DVI-DTV (or DVI-PC) input sources. NUMBER buttons DASH Used to enter a program number for multiple program channels such as 2-1,2-2,etc. TV/VID EO COMP/RGB/DVI TIMER POWER Turns your TV or any other programmed equipment on or off, depending on mode. TIMER Lets you select the amount of time before your TV turns itself off automatically. FLASHBK FLASHBK Tunes to the last channel viewed. SURF Use to scroll the Surf channel list. CHANNEL UP/DOWN Selects available channels found with EZ scan. RATIO Changes the aspect ratio. MUTE SURF VOL CH MUTE Switches the sound on or off. VOLUME UP/DOWN Increases/decreases the sound level. INFO When you watch the TV, displays information on top of the screen. Not available in Component 1-2, RGB and DVI mode. SAP Selects MTS sound: Mono, Stereo, and SAP. Change the audio language in DTV mode. THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference. MENU Brings up the main menu to the screen. SOUND Selects the sound appropriate for the program's character. FREEZE Freezes the currently-viewed picture. Main picture is frozen in PIP/Twin picturre mode. ADJUST Adjusts screen position, clock, and phase in PC mode. ZOOM Enlarges the main picture size. SIGNAL Displays the digital signal strength. MENU INFO SAP RATIO CC ENTER CC Select a closed caption: Off, EZ Mute, and On. EXIT SOUND VIDEO PLAY PAUSE STOP RECORD EXIT Clears all on-screen displays and returns to TV viewing from any menu. VIDEO Adjusts the factory preset picture according to the room. VCR/DVD BUTTONS Control some video cassette recorders or DVD player ("RECORD" button is not available for DVD player). PIP Switches between PIP, POP (Picture-out-ofPicture) and Twin picture modes. PIPCH-/PIPCH+ Changes to next higher/lower PIP channel. PIP INPUT Selects the input source for the sub picture. SWAP Exchanges the PIP/main images. REW FF SKIP PIP PIPCH- PIPCH+ PIPINPUT FREEZE ZOOM SIGNAL SWAP ADJUST Installing Batteries · Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). · Install two 1.5V AA batteries. Don't mix old or used batteries with new ones. Replace cover. 8 Installation Installation Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. MODE POWER LIGHT TV/VIDEO COMP/RGB/DVI TIMER FLASHBK MUTE VOL CH SURF SAP INFO RATIO CC ENTER MENU SOUND VIDEO EXIT PLAY PAUSE STOP RECORD 1.5V 1.5V REW FF SKIP PIP PIPCH- PIPCH+ PIPINPUT FREEZE ZOOM SIGNAL SWAP ADJUST Owner's Manual Batteries Power Cord D-sub 15 pin Cable Remote Control Installation Instruction Wall Mount: Horizontal installation Desktop Pedestal Installation For proper ventilation, allow a clearance of 4" on each side and 2" from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide. For proper ventilation, allow a clearance of 4" on each side and the top, 2.36" on the bottom, and 2" from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer. 4 inches 2 inches 4 inches 2 inches 4 inches 4 inches 4 inches 4 inches 4 inches 9 Installation Installation Instruction - This manual explains the features available on the DU-42LZ30 TVs. Rear A/V Cover * The connection panel is hidden behind the A/V cover. a. Remove the cover. b. Install wires as necessary. c. Reinstall the cover. Position the A/V cover with the TV back panel. d. Align the holes on the TV back panel with the two tuberance on the rear A/V cover and insert. e. Close cover. W ire Holders - Thread, then pull the wires through the hole on the TV stand. 10 Installation External Equipment Connections Antenna Connection Analog and Digital TV signals provided on one antenna - Antenna or Cable Service without a Cable Box Connections - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket Bronze Wire DVI INPUT (PC/DTV INPUT) S-VIDEO Antenna1 Antenna 2 RF Coaxial Wire (75 ohm) VHF Antenna UHF Antenna Turn clockwise to tighten. Bronze Wire Outdoor Antenna Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Be careful not to bend the bronze wire when connecting the antenna. · In a poor signal area to improve picture quality, purchase and install a signal amplifier. · If the antenna needs to be split for two TV's, install a "2Way Signal Splitter" in the connections. DVI INPUT (PC/DTV INPUT) Antenna1 Antenna 2 Signal Amplifier · If the antenna is not installed properly, contact your dealer for assistance. Analog and Digital TV signals provided on two separate antennas Wall Antenna Socket Bronze Wire RF Coaxial Wire (75 ohm) Analog Antenna Turn clockwise to tighten. DVI INPUT (PC/DTV INPUT) Wall Antenna Socket S-VIDEO Antenna1 Antenna 2 RF Coaxial Wire (75 ohm) Digital Antenna Bronze Wire NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches. The TV will let you know when the analog, cable, and digital channel scans are complete. 11 Installation NOTE: All cables shown are not included with the TV VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV - Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual.) 3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source) Do not connect to both Video and S-Video at the same time. COMPONENT 2 DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 DVI INPUT (PC/DTV INPUT) (MONO) COMPONENT 1 S-VIDEO VIDEO Antenna1 Antenna 2 RGB INPUT (PC/DTV INPUT) R L R AUDIO L AUDIO INPUT VIDEO INPUT 1 2 ANT IN ANT OUT S-VIDEO OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH 3 4 IN VCR Cable TV Setup - After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV. - For further information regarding cable TV service, contact your local cable TV service provider(s). Connection Option 1 1. Select 3 or 4 with channel switch on cable box. 2. Tune the TV channel to the same selected output channel on cable box. 3. Select channels at the cable box or with the cable box remote control. COMPONENT 2 DVD /DTV INPUT COMPONENT 1 MONITOR OUTPUT A/V INPUT1 DVI INPUT (PC/DTV INPUT) (MONO) S-VIDEO VIDEO Antenna1 Antenna 2 Connection Option 2 1. Connect the audio and video cables from the Cable Box's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). 2. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source) 3. Select your desired channel with the remote control for cable box. R L R AUDIO L AUDIO INPUT VIDEO INPUT 2 1 (R) AUDIO (L) TV VCR VIDEO OUTPUT SWITCH 3 4 RF Cable Cable Box 12 Installation External A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). COMPONENT 2 DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 COMPONENT 1 (MONO) S-VIDEO VIDEO R L R AUDIO L AUDIO INPUT VIDEO INPUT How to use 1. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source). 2. Operate the corresponding external equipment. Refer to external equipment operating guide. R AUDIO L VIDEO Camcorder Video Game Set Monitor Out Setup The TV has a special signal output capability which allows you to hook up a second TV or monitor. Connect the second TV or monitor to the TV's MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device's input settings. NOTE · Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV input sources cannot be used for Monitor out. S-VIDEO IN (R) AUDIO (L) VIDEO COMPONENT 2 DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 COMPONENT 1 (MONO) S-VIDEO VIDEO R L R AUDIO L AUDIO INPUT VIDEO INPUT DVD Setup How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. NOTE: If your DVD player does not have component video output, use S-Video. COMPONENT 2 DVI COMPONENT1 PC/DVI OUTPUT INPUT INPUT AUDIO INPUT DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 COMPONENT 1 (MONO) S-VIDEO VIDEO DIGITAL AUDIO (OPTICAL) RGB INPUT (PC/DTV INPUT) R L R AUDIO L AUDIO INPUT VIDEO INPUT How to use 1. Turn on the DVD player, insert a DVD. 2. Use the TV/VIDEO or COMP/RGB/DVI button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video 1 or Video 2 external input source.) 3. Refer to the DVD player's manual for operating instructions. · Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Y Y Y Y Y PB PR or or DIGITAL AUDIO OPTICAL (R) AUDIO (L) B R S-VIDEO (R) AUDIO (L) DVD NOTES · Digital Audio will not work for Component 2 input source. · Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. Video output ports on DVD player Pr Pb B-Y R-Y Cb Cr PB PR 13 Installation HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. - This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode. COMPONENT 2 DVI COMPONENT1 PC/DVI OUTPUT INPUT INPUT AUDIO INPUT DVI COMPONENT1 PC/DVI OUTPUT INPUT INPUT AUDIO INPUT DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 COMPONENT 2 (MONO) COMPONENT 1 S-VIDEO VIDEO DVI COMPONENT1 PC/DVI OUTPUT INPUT INPUT AUDIO INPUT DVD /DTV INPUT MONITOR OUTPUT A/V INPUT1 DVI INPUT (PC/DTV INPUT) (MONO) COMPONENT 1 UPGRADE PORT DIGITAL AUDIO (OPTICAL) RGB INPUT (PC/DTV INPUT) DIGITAL AUDIO (OPTICAL) RGB INPUT (PC/DTV INPUT) R L R AUDIO L S-VIDEO VIDEO Antenna1 Antenna 2 AUDIO INPUT VIDEO INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT (PC/DTV INPUT) R L R AUDIO L AUDIO INPUT VIDEO INPUT or or or (R) AUDIO (L) RGB-DTV OUTPUT DIGITAL AUDIO OPTICAL (R) AUDIO (L) B R or DIGITAL AUDIO OPTICAL (R) AUDIO (L) DVI-DTV OUTPUT Digital Set-top Box How to connect Use the TV's COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. Signal 480i 480p 720p 1080i Component 1/2 RGB-DTV,DVI-DTV Yes No Yes Yes Yes Yes Yes Yes How to use 1. Turn on the digital set-top box. (Refer to the owner's manual for the digital set-top box.) 2. Use TV/VIDEO or COMP/RGB/DVI on the remote control to select Component 1, Component 2, RGB-DTV, or DVI-DTV source. Digital Audio Output Send the TV's audio to external audio equipment (stereo system) via the Digital Audio Output Optical port. How to connect 1. Connect one end of an optical cable to the TV Digital Audio Optical Output port. 2. Connect the other end of the optical cable to the digital audio optical input on the audio equipment. 3. Set the " TV Speaker option - Off" in the AUDIO menu. Refer to page 23. See the external audio equipment instruction manual for operation. Caution: Do not look into the optical output port. Looking at the laser beam may damage your vision. DVI COMPONENT1 PC/DVI OUTPUT INPUT INPUT AUDIO INPUT REMOTE CONTROL UPGRADE PORT DIGITAL AUDIO (OPTICAL) 14 Installation PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. - The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. card, change the screen scanning rate for the graphic card accordingly. How to connect 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Use the TV's RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector. · If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the TV. · If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.) 3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required. COMPONENT 2 PC/DVI AUDIO INPUT DVD /DTV INPUT