LAC2800R.DITALLR_ENG_MFL41655318 ENGLISH MODEL : LAC2800R DEUTSCH FRANÇAIS ESPAÑOL ITALIANO Table of Contents 2 3 4 5 6 Table of Contents Safety Note Front Panel About Detachable Control Panel Attaching the control panel Detaching the control panel 9 9 10 Listening RDS broadcasting RDS broadcasting information Connecting an Auxiliary Equipment Listening a CD Pause or restart a CD Search for a section within a track / file Skip to another track / file Intro scan Repeat Shuffle MP3/WMA TRACK -10 / +10 MP3/WMA Folder UP/DOWN See information about your music Installation Basic installation Removing the existing receiver unit ISO-DIN installation 7 8 Connection Basic operation Mute Changing the general settings Using the EQ Adjusting the sound level XDSS+ Checking the clock 11 12 Troubleshooting Specifications 9 Listening to the radio Auto search memory Storing and recalling broadcast frequencies To scan the preset stations To tune in the preset stations This product is manufactured to comply with Directive 2006/28/EEC(ANNEX I , 3.2.9), 72/245/EEC, and 2006/95/EC. European representative : LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere, The Netherlands (Tel : +31-036-547-8940) 2 CAR CD/MP3/WMA Receiver Safety Note CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : This product uses a Laser System. To ensure proper use of this product, please read this owner's manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT SPLIT COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Always operate the vehicle in a safe manner. Do not become distracted by the vehicle while driving, and always be fully aware of all driving condition. Do not change settings, or any functions. Pull over in a safe and legal manner before attempting such operations. Do not use for many hours at extremely low or high temperature. (-10~60°C) To reduce the risk of electric shock, do not remove the cover or back of this product. There are no user-serviceable parts inside. Refer servicing to qualified service personnel. To reduce the risk of fire or electric shock, do not expose this product to dripping or splashing water, rain, or moisture. The temperature of unit's outside can be extremely high, please use the unit after proper installation in your vehicle. This unit cannot play 8cm disc (use 12cm disc only). Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Caution When being connected in a wrong way, the unit displays as follows. · Antenna port short : "ANTENNA ON PORT SHORT CIRCUIT CHECK" After connecting it again, restart the unit. You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players. (Mastered/Live File System : Disc format system for Windows Vista) 8 cm CAR CD/MP3/WMA Receiver 3 Front Panel 1 2 3 [PWR]/[MUTE] Volume UP/DOWN [+/-] i · Skip / Search I/i i · Seek/ Tune I/i U · Auto Store [U/AS] u · Preset Scan [u/PS] u · MP3/WMA Track +10/-10 U/u u · Folder Up/Down U/u Disc slot Display Window Eject Z Release · [PTY] Programme Type · [TA] Traffic Announcement · Display [DISP] 9 10 11 12 13 14 15 4 5 6 7 8 AUX In [AUX] Preset Station [1-6] Shuffle [SHF] Repeat [RPT] Intro Scan [INT] Play/Pause B/X · Equalizer [EQ] · Extreme Dynamic Sound System [XDSS] 16 [BAND] 17 Source [SRC] 18 Select [SEL] / [MENU] 4 CAR CD/MP3/WMA Receiver About Detachable Control Panel Attaching the control panel 1 2 Align the left side of the panel with the stopper. Push the right side or panel into the unit until it clicks. Detaching the control panel 1 1 2 2 3 4 Press the " " (RELEASE) to open the control panel. Hold the right part of the control panel. Pull out the control panel. Place the control panel in the supplied protective case. 2 3 1 Caution · The control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the display. · Do not leave the control panel in any area exposed to high temperatures or direct sunlight. · Do not drop the control panel or otherwise subject it to strong impact. · Do not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. 4 Control panel Protective Case Note Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn off the ignition before cleaning, and remove the key from the ignition switch. CAR CD/MP3/WMA Receiver 5 Installation Basic Installation Bend the claws according to the thickness of the dashboard ISO-DIN Installation Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. 1 2 3 4 Remove the existing receiver unit. Make the necessary connections. Install the installation sleeve. Install the unit into the installation sleeve. 4 5 6 3 2 1 2 1 3 4 5 6 Control panel Control panel Slide the unit into the ISO-DIN frame. Fit screws removed from the old unit. Slide the unit and frame into the dash opening. Install the dash panel or adapter plate. Install the trim ring to the unit. Install the control panel to the unit. Removing the existing receiver unit A If there is already an installation sleeve for the receiver unit in the dashboard, it must be removed. 1 2 Remove the rear support from the unit. Remove the control panel and trim ring from the unit. Insert the lever A into the hole on one side of the unit. Perform the same operation on the other side and pull the unit out from the mounting sleeve. A 3 6 CAR CD/MP3/WMA Receiver Connection Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits. 1 2 1 2 3 4 3 4 5 6 5 6 7 8 7 8 B A Power Antenna A5 Power Antenna(Blue) A6 Dimmer(Pink) A7 To Ignition(Red) A4 To Battery(+)(Yellow) A8 Ground(-)(Black) Control Relay Dimmer Switch Ignition Switch B1 B2 B3 BATTERY B B B B B B B B 1 2 3 4 5 6 7 8 Violet : Rear Right + Violet/ Black Stripe : Rear Right ­ Gray : Front Right + Gray / Black Stripe : Front Right ­ White : Front Left + White/Black Stripe : Front Left ­ Green : Rear Left + Green/ Black Stripe : Rear Left ­ B4 B5 B6 B7 B8 A1, A2, A3 : Not connected CAR CD/MP3/WMA Receiver 7 Basic Operation ON PLAYER 1. Turn the unit on. 2. Select a source. 3. Adjust the volume. PWR/MUTE SRC VOLUME + or - Basic operation - more you can do Mute Press PWR/MUTE to cut the sound. To cancel it, press again. right now. AUX (Auxiliary) ON / OFF It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit. AUX (Auxiliary) 00dB / +6dB You can adjust the volume level of each source to prevent radical changes in volume when switching between sources. You can set to 0 dB or +6 dB. You may be surprised at a loud sound when you change the source from the external component to another source. DEMO OFF/ ON You can change the initial indication on the display to information name (function name, EQ name, etc...) while listen to a source. BEEP 2ND / ALL BEEP 2ND : The beep is generated when a key is long pressed. (1 sec) BEEP ALL : The beep is generated when any key is pressed. Changing the general settings 1 Press and hold SEL/MENU so that one of menu items appears. 2 Press SEL/MENU and press + or - to select one of the settings specified belows. 3 Press and hold SEL/MENU finish the setting. AF(Alternative frequency) ON / OFF When the reception quality drops, the tuner automatically changes to another station in the network, broadcasting a better reception quality, using the PI and AF codes. REG (Region) ON / OFF REG ON : The unit switches to another station, within the same network, broadcasting the same program when the receiving signals from the current station become weak. REG OFF : The unit switches to another station, within the same network when the receiving signals from the current station become weak. (This mode, the program may differ from the one currently received.) TA(Traffic Announcement) ALARM / SEEK TA ALARM : When a newly tuned station has no TP information for 5 seconds, a double beep sound is output. TA SEEK : When the newly tuned station does not receive TP information for 5 seconds, the receiver retunes to the next station which has the same PI as the last station, but has the TP information. PI (Programme Identification) SOUND / MUTE PI SOUND : If the sound of a station with different PI is heard intermittently, the receiver mutes the sound after 1 second. PI MUTE : If the sound of a station with different PI is heard intermittently, the receiver mutes the sound 8 CAR CD/MP3/WMA Receiver Using the EQ EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully. Press XDSS/EQ repeatedly. The indicator lights up in the following order. POP t CLASSIC t ROCK t OFF(Not displayed.) Note When XDSS+ is set to "Off", you can adjust the EQ settings. Adjusting the sound level Press SEL/MENU repeatedly to select the mode you want to adjust from volume, balance and fader. Note When EQ and XDSS+ is set to "Off", you can adjust the sound level (BAS, TRB) settings. XDSS+ (Extreme Dynamic Sound System) Press and hold XDSS/EQ for more 2 seconds. (XDSS+ : Improves the treble, bass sound.) Checking the clock You can see the clock pressing DISP. Listening to the radio ON PLAYER 1. Select a source to tuner. 2. Select a band. 3. Auto seek. Manual seek. SRC BAND < / > (Press and hold) Listening RDS broadcasting ON PLAYER 1. Select a source to tuner. 2. Select a band to FM. 3. Select a programme types. 4. Select a station in PTY type. RDS broadcasting information. Press the PTY repeatedly for selecting each mode. Music group t Speech Group t Search off NO. MUSIC GROUP 1. 2. 3. 4. 5. 6. POP M, ROCK M EASY M, LIGHT M. CLASSICS, OTHER M JAZZ, COUNTRY NATION M, OLDIES FOLK M NO. SPEECH GROUP 1. NEWS, AFFAIRS, INFO 2. SPORT, EDUCATE, DRAMA 3. CULTURE, SCIENCE, VARIED 4. WEATHER, FINANCE, CHILDREN 5. SOCIAL, RELIGION, PHONE IN 6. TRAVEL, LEISURE, DOCUMENT SRC BAND Press and hold PTY 1-6 Listening to the radio - more you can do Auto search memory Press U/AS. The six strongest broadcast frequencies will be stored under preset button 1-6 in the order of their signal strength.To cancel, press U/AS. Storing and recalling broadcast frequencies 1 Press BAND to select desired band you want to store. 2 Select the desired frequency and press one of preset buttons 1-6 and hold until the beep sound. 3 Repeat steps 1-2 to preset other stations.The next time, you press the same preset button, the radio station frequency is recalled from the memory. To scan the preset stations Press u/PS. Each preset station appears. To cancel it, press u/PS again. Connecting an Auxiliary Equipment To tune in the preset stations Press BAND to select the desired band and press the desired preset button 16. Note When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. Auxiliary input MP3 Player, etc Line out ON PLAYER 1. Select a source to AUX. 2. Play the connected Auxiliary Equipment. 3. Ad ...