Detailed instructions for use are in the User's Guide.
ISO 9001 CERTIFIED
www.liteputer.com.tw
DX-610/626
6CH. DMX DIMMER PACK
Lite-Puter Enterprise Co., Ltd.
WEBSITE: www.liteputer.com.tw E-MAIL: sales@liteputer.com.tw
Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
INDEX
Safety Introductions ................. ........... 2
Chapter 1.Introduction of DX-610/626
1-1 1-2 1-3 1-4 1-5 1-6 Feature................................................................ 3 Brief device introduction................................... 3 Specification ...................................................... 3 Front panel ......................................................... 4 Output terminal board / Sockets panel ............ 4 Wiring Diagram .................................................. 6
Chapter 2Operation
2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 Standard DMX512 Signal................................... 6 DMX start address setting................................. 6 Dimming/Switching setting............................... 7 Warm up setting (0...6%)................................... 7 Channel output status preview......................... 7 Manual dimming ................................................ 8 Display the dimming value of DMX channel, internal temperature.......................................... 8 DMX status & DMX address .............................. 8
1
Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
SAFETY INTRODUCTIONS
Please note the load power
Please refer to the data we suggest to ensure the normal total working hours of DX-610/626 1. If DX-610/626 is installed in a rack, please make sure the rack is airy. Otherwise the machine will become over-heat and result in the mis-function. DX-610: the max. output of each channel if 10A: For testing (DO Not over 30 minutes) DX-626: the max. output of each channel if 20A: For testing (DO Not over 30 minutes) 3. DX-610: the output of each channel is8A: For several hours use (Theaters, Stages) DX-626: the output of each channel is16A: For several hours use (Theaters, Stages) 4. DX-610: the output of each channel is 8A: Can work for the whole year without switching off (Hotels, Restaurants, Buildings) DX-626: the output of each channel is 12A: Can work for the whole year without switching off (Hotels, Restaurants, Buildings)
2.
Working Environment
1. Temperature Under 35°C 2. If the machine is installed in a rack, then the temperature inside the rack must be under 45°C 3. Humidity40% --- 80%
Suggested Dimming Lights
Incandescent lamps, halogen lamps, low volt halogen lamps with ballast.
2
Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
Chapter 1.
1-1 Feature
Introductions of DX-610/626
6 dimming channels. Auto tracking of frequency and phase. Temperature control device: When the temperature is over 35the fan will start automatically. Auto tracking of frequency: Enables stable dimming output in different frequencies. Testing function: Can do test without connecting a console. Warm-up function to protect the loads. (Warm-up setting 0---6.0%)
1-2 Brief device introductions
DX-610: 10A no fuse breaker. DX-626: 25A no fuse breaker. Fan for temperature controlling to sink heat and clean the dust inside. (37CFM X 1) The front panel can be dismantled easily for quick repair.
1-3 Specification
Power Output AC100-240V, 45-63Hz, 3Ø4W, 1Ø2W DX-610: Maximal output is 10A each channel DX-626: Maximal output is 20A each channel (Please refer to the user manual) DMX signal output/ input DMX signal connector Analog signal power input Analog input channel DMX512/ 1990 XLR 5Pin, RJ11-6p4c phone jack DC 0-10V 9 channels PIN 1~6( CH1~6, PIN 7(NC, PIN 8(V+12V OUT,PIN 9(GND Analog signal connector D-Type Plug 9Pin(F)
3
Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
Dimension Location Weight 1-4 Front panel
482(W) x 88(H) x 300(D)mm 19" 2U standard rack 8Kg
4
CH1 CH2 CH3 CH4 CH5 CH6
2
DMX OUT
6CH. DMX DIMMER PACK
DX-610/626
ANALOG IN 0~10VDC
PUSH
1 2 3
4 5 6
PIN1~6:CH1~CH6 PIN7:NC PIN8:V+12V OUT PIN9:GND
10 9 8 7 6 5 4 3 2
10 9 8 7 6 5 4 3 2
10 9 8 7 6 5 4 3 2
ON FNC DMX
L
1:V+12V 2:Data+ 3:Data4:GND
T
4 3 2 1 4 3 2 1
DMX IN
CONTROL OFF
7
(1) Power on/ off switch
8
(5) (6) (7)
6
Function Key
5
3
1
(2) DMX OUT/ IN (5 pin) (3) DMX IN (RJ11, phone jack)
Dimming VR of Channel 1- 6 No fuse breaker (Channel 1-3)
(4) LED display/ function keys
(8) No fuse breaker (Channel 4-6)
1-5 Output terminal board / Sockets panel
TERMINAL TYPE
9
10 11
12
13 (12) Power input terminal board. (DX-610: 20A Single phase; DX-626: 40A Single phase)
(9) DMX connector (RJ11, phone jack)
(10) DMX IN
(XLR-3 pin)
(13) Output terminal board (10A each channel, External power no fuse
4 Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
(11) DMX OUT (XLR-3 pin)
breaker is necessary when mounting.)
AMERICAN TYPE
Output sockets (DX-610: 10A each channel; DX-626: 15A each channel,External power no fuse breaker is necessary when mounting.)
SCHUKO TYPE
Output sockets (DX-610: 10A each channel; DX-626: 16A each channel,External power no fuse breaker is necessary when mounting.)
1-6 Wiring diagram
5 Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
3 PHASES 4 WIRES N THE BEST WIRING DIAGRAM R S T
E N V1 V2 V3
SINGLE PHASES 2 WIRES
N V
V
E N V1 V2 V3
PS.:
There are `3 PHASES 3 WIRES' and `SINGEL PHASE 3 WIRES' as option.
Chapter 2.
2-1
Operation
Standard DMX512 Signal
This point flashing when receiving DMX
2-2
DMX start address setting
STEP-1 holdingDMX, pressorto find the start address.
: move 1 number forward : up to Channel 512
: move 1 number backward :down to Channel 1
6
Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
DX-626 is a 6 channel dimmer pack so when setting this unit: 1 as C.001, the output is from Channel 1 Channel 6. 2 as C.007, the output is from Channel 7 Channel 12. 3 It is allowed for setting more than 1 piece of DX-626 at the same start address.
2-3
Dimming/Switching setting
STEP-1 pressDMXkey into DMX status STEP-2 press and hold theFNCkey for 3 sec. Default settingall channel are dimming mode
STEP-3 pressFNCkey to select channel STEP-4 pressorto select dimming mode or switching mode
(dimming)
(Switching)
2-4
warm up setting (0...6%)
STEP-1 pressFNCkey
STEP-2 pressFNCkey to select the setting channel, EX :select channel 1 STEP-3 press,key to adjust Channel 1 set on 6% for warm up
2-5
Channel output status preview
STEP-1 Enter to DMX status and pressDMXkey STEP-2 pressorto preview
7
Lite-Puter DX-610/626 [EUM-E]
ISO 9001 CERTIFIED
www.liteputer.com.tw
2-6
Manual dimming
STEP-1 PushVR1-VR6to do the prompt dimming output of individual channel. When there is another signal inputting from a console, it will take the higher value as the output.
2-7
Display the dimming value of DMX channel,
internal temperature.
PressLto display the dimming value of DMX channel. PressTto display the internal temperature.
2-8
DMX status & DMX address
a.pressDMXto DMX status b.10 minutes unused of unit, the DMX will activate to DMX status
8
Lite-Puter DX-610/626 [EUM-E]
...
