User manual LUX WH1093

ROYAL INSTALLATION AND INSTRUCTION MANUAL PEMASANGAN DAN BUKU PETUNJUK WASHING MACHINE MESIN CUCI WH1093 WH1093 GB 147165000 ID Important Safety Information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings have been provided in the interest of safety. You MUST read them carefully before use or installation by a qualified person. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. Installation · This appliance is heavy. Care should be taken when moving it. · It is dangerous to alter the specifications or attempt to modify this product in any way. · All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in instructions. · Care must be taken to ensure that the appliance does not stand on the electrical supply cable. · If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely. · Only wash fabrics which are designed to be machine washed. If in doubt, consult the care label on the clothes. · Before washing, ensure that all pockets are empty and buttons and zips are fastened. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass before washing. Underwired bras must NOT be machine washed. · Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine. · Garments which have been in contact with volatile petroleum products should not be machine washed. If volatile cleaning fluids are used, care should be taken to ensure that the fluid is removed from the garment before placing in the machine. · Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum. · Only use the advised quantities of fabric softener. Damage to the fabric can ensue if you over-fill. Refer to the manufacturer's recommendations of quantities. · As some duvets and eiderdowns should be washed in large commercial machines because of their bulk, please check with the manufacturer of the item before washing in a domestic machine. Child Safety · This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product. · Pets and children have been known to climb into washing machines. Please check your drum before use. · The glass door becomes very hot during the washing cycle. Keep children away from the vicinity of the appliance whilst it is in operation. · Keep all packaging well away from children. · Keep all detergents in a safe place out of children's reach. · When the appliance is to be scrapped, cut off the electrical supply cable and destroy the plug with the remaining cable. Disable the door catch in order to prevent children from becoming trapped inside while playing Maintenance and Cleaning · Leave the porthole door slightly ajar between washes to preserve the door seal. · For information on maintenance and cleaning your washing machine see page 23 of this Instruction manual. Use · Always unplug the appliance and turn off the water supply after use. · Do not overload the appliance. See relevant section in the instruction book. 2 Service · This product should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Ecological hints To save water and energy and help protect the environment, we recommend that you follow these hints: · Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). · The machine works more economically if it is fully loaded. · With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. · Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed. Environment Information · Materials marked with the symbol are recyclable. · Check with your local Council or Environmental Health Office to see if there are facilities in your area for re-cycling this appliance. · When the appliance is to be scrapped, cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside. · Help to keep your country tidy - use authorised disposal sites for your old appliance. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Important Your machine is fitted with a balance control device, which ensures the machine is stable during the spin. If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the wash load manually and select a spin programme. For more detailed information see the section headed "Something Not Working". 3 Contents For the User Important Safety Information Description of the Appliance Door lock indicator Detergent dispenser drawer Child safety feature For the Installer 2 5 5 5 5 Installation Technical Specifications Unpacking Positioning Water inlet Water drainage Levelling Special conditions In the interest of the environment 6 6 7 7 8 8-9 9 9 9 The Control Panel 11-15 Programme information 15 Special features 16 Using your washing machine 17-18 Load the laundry Measure out the detergent Measure out the fabric softener Select the desired programme Select the spin speed or the "No spin" option Select the desired options Select the "Delay start" Start the programme How to change an option or a programme during its cycle How to interrupt a programme How to open the door during the cycle of a programme End of programme 17 17 17 17 17 17 18 18 18 18 18 18 Electrical connection 10 Guide to use the Instruction Manual The following symbols will be found in the text to guide you throughout the instructions: Hints and tips on Washing Wash Care Symbols Washing Programmes Maintenance and Cleaning Descaling After each wash Maintenance Wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the pump Cleaning the water inlet filter The dangers of freezing Emergency emptying out 19 20 21-22 23-24 23 23 23 23 23 23 23-24 24 24 24 Safety instructions Hints and tips Environmental information Something Not Working 25-26 This appliance complies with the following E.E.C. Directives: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications. 4 Description of the Appliance 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Filter 5 Adjustable feet 6 Door lock indicator 1 2 Royal Miniprogram 30° Easy Iron 40° Spin Drain Rinse Handwash Cold Handwash 30° Handwash 40° Delicate Cold Delicate 30° Delicate 40° Cottons Off Synthetics 95° Economy 60° 60° Economy 40° 40° 30° Cold 60° Economy 60° 40° 30° Cold Wash time Spin Child lock Super rinse Quick Wash Delay start Night cycle Prewash Stain Start/Pause WH1093 6 3 Door lock Indicator It stays on during the whole programme indicating that the door is locked. When the light goes out, the door can be opened. 4 5 Detergent dispenser drawer Prewash Main wash Fabric softener Child safety feature This machine incorporates a special child safety feature to prevent small children from being trapped inside the machine. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical. P1131 5 Installation It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. Technical specifications DIMENSIONS Height Width Depth Cotton Synthetics Delicates Woollens Hand wash Silk 85 cm 60 cm 60 cm 7.0 3.0 3.0 2.0 2.0 1.0 kg kg kg kg kg kg MAXIMUM LOAD SPIN SPEED POWER SUPPLY VOLTAGE/ FREQUENCY TOTAL POWER ABSORBED MINIMUM FUSE PROTECTION WATER PRESSURE Minimum Maximum 1000 rpm max. 220-240 V/50 Hz 2200W 10 A 0.05 MPa 0.8 MPa 6 Unpacking Warning ! Slide out the polythene bag containing the polystyrene block before using the appliance. Pull off adhesive strips from inside machine on top of drum. Keep all packaging away from children All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 5. Set the machine upright and remove the remaining rear screw. Slide out the relevant pin. 6. Plug all the holes with the plugs which you will find in the envelope containing the instruction manual. P1128 P0002 P1129 P0001 1. Using a spanner, unscrew and remove the two rear bottom screws. Slide out the two plastic pins. Lay the machine on its back, taking care not to squash the hoses. This can be avoided by placing one of the corner packing pieces between the machine and the floor 1 2 3 Important ! You are advised to keep all the packaging for reuse in case the machine is to be transported again. In case of moving out the same precautions as per paragraph "The dangers of freezing" must be taken i.e. the residual water in the hoses must be pumped out. Keep all packaging away from children Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Your new washing machine has been designed to be permanently plumbed in to your home's water supply and drainage system. However, if this is not possible, it may be connected to suitable existing tap with the drain hose discharging into a sink. The appliance has one inlet hose, with female 3/4" BSP thread connector. If this connection is not compatible with the plumbing of the existing installation, a variety of connectors are available from good hardware stores and plumber merchants to suit most domestic plumbing. Any alteration to your existing plumbing must be carried out by a competent person, or qualified plumber. P1123 P1126 2. Remove the polystyrene block(s) from the bottom of the machine and release the two plastic bags. 3. Very carefully slide out the left polythene bag, removing it towards the right and then downwards. Installation on a Suspended Floor P1127 4. Very carefully slide out the right polythene bag, removing it towards the left and then upwards. Remove the bottom cover found inside the drum of your appliance, lay it's hook as the arrow 'A' indicates and push the top of the cover to seal it closed. 7 Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor beams with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable. Water inlet Connect the hose to a tap with a 3/4" thread. Always use the hose supplied with the appliance to connect to the water supply. Do not use previously used hoses for water connection. P1199 U piece supplied Place the drain hose into your standpipe, which should have an internal diameter of approximately 38mm thus ensuring there is an air break between the drain hose and standpipe. P1088 38 mm (11.2) standpipe diameter 30 cm (12") Installation should comply with local water authority and building regulations' requirements. The appliance must be connected to a cold water supply. A minimum water pressure of 0.05 MPa is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum distance of 5.02m (16.5 ft) between the appliance's inlet and the bottom of the water storage tank. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. When discharging into a standpipe ensure that the top of the standpipe is no more than 90cm (35.4'') and no less than 60cm (23.6'') above floor level. 3 pin P1039 The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter of 18mm. P0021 Water drainage This appliance is designed to be permanently plumbed into your home's drainage system using one of the following methods. 1. Into a drainage standpipe. Firstly form a hook in the end of the drain hose using the "U" piece" supplied. If your drain hose looks like this (see below) you do not require the "U" piece". Just push the hose firmly into the standpipe. P1212 8 Min. 60 cm (23.6) Max. 90 cm (35.4) 2. Onto a sink outlet spigot. If the outlet spigot has not been used before, remove any blanking plug that may be in place. Some vibration is inevitable, especially if mounted on a wooden floor. Sprung wooden floors are particularly susceptible to vibration. For advice, consult a builder. If possible, always place the machine on a solid floor. Special conditions If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine. Warning The machine should NOT be placed on deep pile carpeting. Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown. Loop P1198 P1197 Push the drain hose onto the spigot and secure with a clip if required, ensure a loop is formed in the drain hose (see diagram) to prevent waste from the sink entering the washing machine. In the interest of the environment Washing machines and dishwashers should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. Important Before connecting the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. For a correct functioning of the machine the drain hose must be hooked on the proper support piece situated on the top of the back side of the appliance. SHOWER Levelling Level the washing machine by raising or lowering the feet. The feet may be tight to adjust as they incorporate a self locking nut, but the machine MUST be level and stable (check diagonally). RAINWATER 'RUN-OFF' SINK BATH TOILET BIDET WASHING MACHINE DISHWASHER FOUL DRAIN SURFACE WATER DRAINS & SEWERS FOUL SEWERS SEWAGE TREATMENT WORKS TREATED DISCHARGE RIVER RIVER UNTREATED DISCHARGE P0987 P1051 Any necessary adjustment can be made with a spanner. Accurate levelling prevents vibration, noise and displacement of the machine during operation. 9 It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local water authority. Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. Should the appliance power supply cable need to be replaced, this must be carried out by a Service Force agent. The manufacturer declines any liability should this safety measure not be observed. The plug must still be accessible after the appliance has been installed The appliance should not be connected to the electrical supply by means of an extension cable. The power supply cable must be easily accessible after installing the appliance. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance's rating plate. The rating plate is located at the top of the rim of the open door. Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. Mo Pro d. ..... d. No ..... . ..... ..... . Ser . No . ..... .... Mod. .......... Prod. No. ........... P0042 BD Ser. No. ......... This machine is designed to operate on a 220-240 V, singlephase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2.2 kW), also taking into account any other appliances in use. Important! When the appliance is installed the power supply cable must be easily accessible. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre. 10 The Control Panel Royal Miniprogram 30° Easy Iron 40° Spin Drain Rinse Handwash Cold Handwash 30° Handwash 40° Delicate Cold Delicate 30° Delicate 40° Cottons Off Synthetics 95° Economy 60° 60° Economy 40° 40° 30° Cold 60° Economy 60° 40° 30° Cold Wash time Spin Child lock Super rinse Quick Wash Delay start Night cycle Prewash Stain Start/Pause WH1093 1 2 3 7 48 59 6 10 11 1 Detergent dispenser drawer 2 Programme selector dial The selector is divided into the following sections: · Cottons, linens · Synthetics · Delicates · Handwash · Special programmes "Easy Iron 40°" and "Minipro gram 30°". · Reset / Off programme OFF Miniprogram 30° Easy Iron 40° Spin Drain Rinse Handwash Cold Handwash 30° Handwash 40° Delicate Cold Delicate 30° Delicate 40° Off 95° Economy 60° 60° Economy 40° 40° 30° Cold 60° Economy 60° 40° 30° Cold Spin speed The following speeds are available for the different fabrics: · Cottons : 1000/ 800/ 600/ 400/ 0 max 1000 r.p.m. · Synthetics : 900/ 800/ 600/ 400/ 0 max 900 r.p.m. · Delicates : 700/ 600/ 400/ 0 max 700 r.p.m. h min 1000 Spin Child lock Cotton 95° Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause Cottons L002 Synthetics 0 No spin «0» option No spin option can be selected by depressing the spin button .By selecting this option the spinning phases are suppressed. If you select this option with programmes for cotton and synthetics, the machine will perform some extra rinses. L001 The selector dial can be turned either clockwise or anticlockwise. Positions "Economy 60° " correspond to an ENERGY SAVING programmes and position "Cold" to a cold wash. Before setting the dial to any position ensure that the machine is turned to the "Off" position. Important At the end of the programme the selector dial must be turned to position "Off". 4 Super rinse button This option can be selected with all programmes except Handwash and Miniprogram 30. The machine will add 2 rinses for cotton and 1 rinse for Synthetics and Delicates. This option is recommended for people who are allergic to detergents, and areas where the water is very soft. 3 Spin button Press this button to reduce the maximum speed of the final spin proposed by the machine for the selected programme. The display will show the selected spin speed and only for 5 seconds the max speed allowed for the selected programme. After 5 seconds the display will show selected spin speed and then the selected programme. 0 If you select «0» option, the machine eliminates all the spin phases. The display will show for 5 seconds the message «No Spin». 11 h min 1000 Spin Child lock Extra rinse YES Super rinse Quick Wash 2.33 Delay start Night cycle Prewash Stain Start/Pause L003 5 Quick Wash button This option can be used for lightly soiled items in order to obtain a good washing programme in a short time. This option is not available for "Cotton E 60°, "Cotton E 40°", "Synthetic E 60°", "Handwash" and "Miniprogram 30°" programmes. The washing time will be reduced according to the type of fabric . When this option is selected the corresponding light illuminates and the display shows "Quick" for 5 seconds. h min 1000 Spin Child lock Start in 30 min Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause L005 7 Night cycle button When you choose this option, the machine will not drain the water of the last rinse, so as not to wrinkle the laundry. As all spinning phases are suppressed, this washing cycle is very noiseless and it can be selected at night or in times with a more economical power rate. This option can be selected with all washing programmes. The machine will add 3 rinses for cotton and 1 rinse for Synthetics and Delicates. The cycle finishes with the water in the tub. To drain the water and to have the final spin, re-press the pause button. h min 1000 Spin Child lock Quick YES Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause L004 6 Delay Start button The wash programme can be delayed from 30 min ­ 60 min ­ 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button. Selecting the delayed start Select the programme and the required options. Select the delay start. The corresponding light illuminates and the display shows for 5 seconds the message «Start in...» to indicate that a delay start has been selected. Depress "Start/ Pause" button: the machine starts its countdown in hours and, for the last 2 hours, in minutes. The programme will start after the selected delay has expired. Cancelling the delayed start Depress "Start/ Pause" button. Depress repeatedly "Delay start" button until the message «Delay Start NO» is displayed. Depress "Start/Pause" button again to start the programme. Important! The door will be locked throughout the delay time (the door locked light is on). If you need to open the door, you must first set the washing machine to Pause by pressing the "Start/ Pause" button. The door locked light goes out. After you have closed the door press the "Start/ Pause" button again. h min 1000 Spin Child lock Night cycle YES Super rinse Quick Wash 2.32 Delay start Night cycle Prewash Stain Start/Pause L006 8 Prewash button Select this option if you wish your laundry to be prewashed before the main wash (not available for "Miniprogram 30°" and "Handwash" programmes). The prewash ends with a short spin at 700 rpm in programmes for cotton and synthetic fabrics, whereas in the programme for delicate fabrics the water is only drained. This option can be selected for heavily soiled laundry but not together with "Stain"option. h min 1000 Spin Child lock Prewash Yes Super rinse Quick Wash 2.54 Delay start Night cycle Prewash Stain Start/Pause L007 12 9 Stain button Select this button if you wish to add to the washing of heavy soiled laundry a stain phase: at the temperature of 40°C the special detergent for stains is loaded from the compartment marked . This function is available in cotton, synthetic & delicate programmes with a temperature of 40° or higher. The washing time will be prolonged by few minutes. The "Prewash" and the "Stain" options cannot be selected together 11 Display The display shows the following information: Duration of the programme ­ spin speed option selection - washing phases - delayed start ­ incorrect option selection ­ alarm message ­ end of programme. Duration of the selected programme After selecting a programme, the duration is displayed in hours and minutes (for example 2.23). The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric. If the load of laundry to be washed is small, at the beginning of the cycle the display will still indicate the programme duration relevant to the maximum load. The duration value will be gradually adjusted during the execution of the cycle. After the programme has started, the remaining time is updated every minute. Standby After 10 minutes of inactivity in Setup Mode or at the End of the Cycle, the backlight of the display automatically switches off. Pressing any key or moving the selector the display returns in its normal status. h min 1000 Spin Child lock Stain Yes Super rinse Quick Wash 2.34 Delay start Night cycle Prewash Stain Start/Pause L008 10 Start / Pause button This button has two functions: Start ­ Pause. Start After having selected the required programme, press this button to start the machine; the corresponding pilot light stops flashing and stays on during the washing programme. If you have selected the delayed start, the machine begins its countdown. The duration of the programme and the delay appears on the display. Pause To interrupt a programme which is running, depress the "Start/ Pause" button: the corresponding pilot light starts start to flash. To restart the programme from the point at which it was interrupted, press the "Start/ Pause" button again. h min 1000 Spin Child lock Cotton 95° Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause L0010 Spin speed After selecting a programme, the maximum spin speed proposed for the selected fabric/programme is displayed. h min 1000 Spin Child lock Cotton 95° Super rinse Quick Wash 2.23 Delay start h min Night cycle Prewash Stain Start/Pause 1000 Spin Child lock Cotton 95° Super rinse Quick Wash 2.23 Delay start L0011 Night cycle Prewash Stain Start/Pause L009 At the end of the programme the Start/pause button light goes out. If you press repeatedly the "Spin" button it is possible to reduce the spin speed proposed by the machine. 0 If you select «0» all the spin phases will be suppressed. The display will show for 5 seconds the message «No spin». 13 h min h min 0 Spin Child lock No spin Super rinse Quick Wash 2.23 Delay start 1000 Spin Child lock Start in 30 min Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause Night cycle Prewash Stain Start/Pause L0012 L0017 Option selection Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before depressing the "Start/ Pause" button. When you press an option button, (for ex. the Prewash ) the corresponding light illuminates and, on the display, appears the description of the selected function. If you press the same button again, the button light goes out and the display shows that this option has been deactivated. The countdown is updated every hour and for the last 2 hours, every 30 minutes. Incorrect option selection If an option which is not compatible with the set wash programme is selected, the message «Selection error» is displayed for about 3 seconds. h min 1000 Spin Child lock Selection error Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause h min h min 1000 Spin Child lock Prewash Yes Super rinse Quick Wash 2.54 Delay start 1000 Spin Child lock Prewash No Super rinse Quick Wash 2.54 L0018 Delay start Night cycle Prewash Stain Start/Pause Night cycle Prewash Stain Start/Pause Alarm messages L0013 L0014 Washing phases During the washing cycle, the display will show the different washing phases. In the event of operating problems, some corresponding messages are displayed (for more information see paragraph "Something not working" at page 25). Some of these problems are due to an incorrect use of your washing machine and are easy to resolve. h min h min 1000 Spin Child lock Washing Super rinse Quick Wash 2.23 Delay start 1000 Spin Child lock Spinning Super rinse Quick Wash 2.05 Delay start h min 1000 Spin Child lock No incoming water Super rinse Quick Wash 2.23 Delay start Night cycle Prewash Stain Start/Pause Night cycle Prewash Stain Start/Pause Night cycle Prewash Stain Start/Pause L0015 L0016 L0019 Delayed start The selected delay (20 hours max) set by means of the relevant button appears on the display for 5 seconds, then the selected programme displays.Press the Start/ Pause button to start the delay start. End of programme When the programme has finished (when the water has emptied out) and the light of the "Start/ Pause" button and the door locked light go out, then the door can be opened and the display will show alternatively the messages «Door openable» and «Cycle ended». 14 Miniprogram 30° h min h min 1000 Spin Child lock Door openable Super rinse Quick Wash 0 Delay start 1000