User manual MARANTZ CC4001 - Product Manual

Model CC4001 User Guide CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. 2. 3. 4. 5. 6. 7. 8. 9. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacture's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment. Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Additional Safety Information! · This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. · Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. · When the switch is in the OFF position, the apparatus isn't completely switched-off from the MAINS. · The equipment shall be installed near the power supply so that the power supply is easily accessible. CONTENTS FOREWORD.....................................................................................................1 EQUIPMENT MAINS WORKING SETTING .............................................................................1 COPYRIGHT ............................................................................................................................1 FOREWORD This section must be read before any connection is made to the mains supply. INTRODUCTION ..............................................................................................2 PRODUCT FEATURES ............................................................................................................2 APPLICABLE DISCS TO THE UNIT ........................................................................................2 PLAYING CD-R/CD-RW DISCS ...............................................................................................2 PLAYING MP3 FILES ...............................................................................................................2 EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. CC4001 can be powered by 120V AC only. BEFORE USING...............................................................................................3 NOTES FOR REMOVING SHIPPING SCREWS .....................................................................3 NOTES ABOUT THE DISCS ....................................................................................................3 INAPPROPRIATE PLACES FOR INSTALLATION ..................................................................3 PRECAUTIONS ........................................................................................................................4 USING REMOTE CONTROL UNIT ..........................................................................................4 LOADING BATTERIES .............................................................................................................4 COPYRIGHT Recording and playback of any material may require consent. For further information refer to the following: --Copyright Act 1956 --Dramatic and Musical Performers Act 1958 --Performers Protection Acts 1963 and 1972 --Any subsequent statutory enactments and orders NAMES AND FUNCTIONS ..............................................................................5 FRONT PANEL..........................................................................................................................5 DISPLAY WINDOW...................................................................................................................6 REAR PANEL ............................................................................................................................7 REMOTE CONTROLLER..........................................................................................................8 REMOTE CONTROL CODE SETTING ....................................................................................9 CONNECTIONS .............................................................................................10 OPERATION...................................................................................................11 CONNECTING THE POWER SUPPLY AND TURNING ON .................................................11 NORMAL PLAYBACK ............................................................................................................11 PAUSE PLAYBACK.................................................................................................................12 STOP PLAYBACK ...................................................................................................................12 CHANGE DISCS WHILE PLAYING .......................................................................................12 PLAYING YOUR FAVORITE TRACKS OF A DISC ...............................................................13 PLAYING YOUR FAVORITE PARTS OF A TRACK ..............................................................13 SEARCH YOUR FAVORITE TRACKS (AMS (AUTOMATIC MUSIC SCAN)PLAY) ..............13 PLAYING TRACKS IN A RANDOM SEQUENCE (RANDOM PLAY) .....................................14 REPEAT PLAY .......................................................................................................................15 PLAYING TRACKS IN A SPECIFIC SEQUENCE (PROGRAM PLAY) ..................................15 BACK TO NORMAL PLAY WITHOUT CLEARING PROGRAM .............................................16 CHECK THE PROGRAM .......................................................................................................16 CHANGE PROGRAMMED TRACKS .....................................................................................16 CLEAR PROGRAMMED TRACKS .........................................................................................17 DISPLAY WINDOW BRIGHTNESS ADJUSTMENT ..............................................................18 SWITCHING PLAYING TIME DISPLAY .................................................................................18 TROUBLE SHOOTING ..................................................................................19 SPECIFICATIONS..........................................................................................20 1 ENGLISH INTRODUCTION ENGLISH PLAYING MP3 FILES APPLICABLE DISCS TO THE UNIT Audio CD (CDDA) Audio CDs contains music tracks only. There are many sites on the Internet from which you can download music files in MP3 format. These files can be downloaded following the instructions on the site and stored on CD-R/RW discs which can then be played on the this unit. The music on commercially available music CDs can be converted into MP3 files on a computer using MP3 encoding programs. When this is done, the data is reduced to approximately 1/10 the original size. This MP3 data can then be stored on a CD-R/RW disc, allowing you to create a single 12 cm CD-R/RW disc containing about 10 times more music than a normal music CD, that is some 100 tracks or more (*). * This is an approximately value for MP3 files of tracks about 5 minutes long converted at a standard bit rate (128 kbps) and stored on a CD-R/RW disc with a capacity of 650 MB. * According to copyright law, use of recorded material other than for personal listening etc. without permission from the copyright owner is prohibited. PRODUCT FEATURES · MP3 File and CD-R/RW Play Compatible This unit can play back music CD format and CD-R/RW discs containing MP3 music data. For restrictions about MP3 files, please refer to "PLAYING MP3 FILES". · While Playing a disc, four other discs can be changed · Direct Disc Access Button Direct Disc Access button is equipped both on the front panel of the unit and on the remote control unit for one-touch disc change to any of the 5 discs in the unit. CD-R NOTES: This unit is compatible with the MP3 file specifications shown in the table below. Playback of MP3 files based on specifications other than those shown in the table below cannot be guaranteed. CD-RW · Various Play Modes such as Random, Program, Repeat, and AMS (Automatic Music Scan) · Headphone Jack with Volume · RS-232C Control Port and IR Flasher Input RS-232C port which supports both unit control and operating status transmission is equipped to enable central control with custom installation. Also, Flasher input is equipped to realize wired control when you cannot use remote control due to the installation on the rack, etc. PLAYING CD-R/CD-RW DISCS This unit can play back the CD-RW (ReWritable) discs as well as ordinary Audio CD and CD-R (Recordable) discs. · This unit can play back music CD format and CD-R/CD-RW discs which contain MP3 music data. However, some discs may have problems such as unable to play, noise or sound distortion. *For details, please read the instruction manual provided with a CD recorder. · The CD-R and CD-RW discs should contain properly-recorded TOC information so that they can be played back. In CD recorders, the task of writing TOC information is referred to as finalizing the disc. Discs that are not finalized cannot be properly recognized as an Audio CD and played back by regular CD players and Super Audio CD players. For details, please read the instruction manual provided with a CD recorder. *TOC stands for Table Of Contents and contains information such as the total number of tracks and total playing time of the disc. · This unit can play only the discs recorded in the CD-DA format designed for music reproduction. Do not attempt to play a disc containing other data, such as a CD-ROM for PCs, on this unit. · As the playback of a CD-RW disc necessitates partial change of the player setup, it may take longer time for reading the TOC information than when an Audio CD or CD-R disc is played. Extension ".MP3 (.mp3)" ISO9660 Level 1 ISO9660 Level 2 Number of folders that can be recognized (per disc) maximum99 maximum255 Number of tracks that (per folder) maximum999 can be recognized (per disc) Constant bitrate (32kbps­320kbps) Bit rate Variable bitrate 8 kHz (MPEG2.5 audio layer 3) 11.025 kHz (MPEG2.5 audio layer 3) 12 kHz (MPEG2.5 audio layer 3) 16 kHz (MPEG2 audio layer 3) 22.05 kHz (MPEG2 audio layer 3) Sampling frequency 24 kHz (MPEG2 audio layer 3) 32 kHz (MPEG1 audio layer 3) 44.1 kHz (MPEG1 audio layer 3) 48 kHz (MPEG1 audio layer 3) Writing program's format File type · 5 Sets of Built-In Remote Control Codes Because there are 5 sets of built-in remote control code signals for between the unit and remote control unit, up to 5 units installed in the same place can be remotely controlled independently. · Aluminum Front Panel Hairline finish aluminum front panel is used for quality look. 2 · Generally speaking, the higher the MP3 file's bit rate, the better the sound quality. With this unit it is recommended to use MP3 files written with a bit rate of 128 kbps or greater. · This unit is compatible with variable bit rate. (In variable bit rate, time display may not be appeared properly.) · The writing program may change the positions of the folders and files when writing the MP3 files on the CD-R/RW disc, so the files may not be played in the expected order. · Make sure to give MP3 files the extension ".MP3 (.mp3)". Files with extensions other than ".MP3 (.mp3)" or without extensions cannot be played. (On Macintosh computers, MP3 files can be played by adding the extension ".MP3 (.mp3)" after the file name consisting of a maximum of 8 Roman capital letters and/or numerals when recording them on CD-R/RW discs.) · Files other than those with the extension ".MP3 (.mp3)" are not counted. · It may not be possible to play some CD-R/RW discs due to dirt, scratches or the disc's properties. · Do not apply seals or tape to the label or signal side of CDs or CD-R/RW discs. The glue could get on the disc surface, making the disc get stuck inside the set. · This unit is multi-session compatible. Only first music CDs can be played if the first session is a music CD, and all the MP3 files can be played if the first session consists of MP3 files. · This unit is mixed-audio compatible. If the first session consists of MP3 files and mixed up with music and MP3 files, only the MP3 files can be played. · This unit is not compatible with packet write programs. · This unit is not compatible with play lists. · This unit is not compatible with ID3-Tag. · This unit cannot display the total time for discs recorded in MP3 format. BEFORE USING NOTES FOR REMOVING SHIPPING SCREWS At the bottom of the player there are two red shipping screws for use when the player is transported. Before using the player, turn these screws counterclockwise and remove them. If the shipping screws are still in place and the power is turned on, unplug the power cord from the power outlet and remove the shipping screws. Retain these screws as they will be needed when the player is transported. Before transporting the player, take out the discs, close the disc tray, set to standby mode and unplug the power cord from the power outlet. Then install the shipping screws by turning them clockwise. Be sure to fasten them securely. * Use discs which satisfy the CD standards such as those with the "CD logo" or " " mark on their disc label surfaces. INAPPROPRIATE PLACES FOR INSTALLATION To keep your player in perfect working order for the longest possible time, avoid installing the player in the following locations. · Wherever it will be exposed to direct sunlight · Wherever it will be close to a heater or other heat-radiating appliance · Wherever the humidity is high or ventilation is poor · Wherever it is very dusty · Wherever it will be subject to vibration · On top of a rickety stand or in an unstable location which is tilted at an angle · In an audio rack with little space at the top and bottom or other location where the heat dissipation will be obstructed · To ensure proper heat dissipation, install the player while leaving clearances between the player and wall or other components, as shown in the figure below. · On top of an amplifier or other component which dissipates a great deal of heat * The quality of the laser and other components can be harmed if the player is placed directly on top of an amplifier or other device which generates heat. NOTES ABOUT THE DISCS * Handle the discs carefully so as not to scratch their surfaces. * Keep the surfaces of the discs clean at all times. When cleaning the surfaces of discs, always be sure to use the special cleaner and wipe the surfaces in the directions shown in the figure below. No guarantees are made for playback if discs which do not satisfy the appropriate CD standards are used. Similarly, no guarantees are made for their sound quality even if it is possible to play such discs. * To protect your discs from damage, avoid placing them in the following locations. · Where they will be exposed to direct sunlight or where they will be close to a heater or other heat-radiating appliance · Where the humidity level is high or it is very dusty · Near a window or other such location where they may be exposed to rain · Wipe the surface radially from the center. · Do not wipe the surface in the circumferential direction. * Get into the habit of putting the discs back in their cases after use. * Do not attach pieces of paper or stickers to the label surfaces of the discs. When a disc has a piece of plastic tape or rental CD label with paste protruding from the edge or when a disc still bears traces of sticky tape or adhesive labels, do not attempt to play it. If such a disc is played on the CD player, you may find that you cannot remove it or that some other kind of malfunctioning may occur. 4 ins. (0.1 m) or more 5 DISC CD CHANGER CC4001 1 2 3 4 5 DISC SKIP STANDBY 4 ins. (0.1 m) or more OPEN/CLOSE PLAY STOP PAUSE 1 2 3 4 5 DISC TOTAL EACH REMAIN R TRACK MIN SEC 12345 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MP3 CD PROGRAM RANDOM REPEAT 1DISC REPEAT RANDOM LEVEL POWER ON/STANDBY PHONES shipping screws 4 ins. (0.1 m) or more * Do not use discs which come in special shapes. Do not attempt to play heart-shaped or octagonal discs or discs with any other special shapes. You may find that you cannot remove them or that some other kind of malfunctioning may occur in the player. 7 Do not place objects on top · Refrain from placing any objects on top of the player. 3 ENGLISH 7 Cautions on handling power cord · Do not touch the power cord with wet hands. · When disconnecting the power cord, always make sure that you take hold of the plug. Yanking out or bending the cord can damage it and/or cause electric shocks or a fire. · Get into the habit of disconnecting the power plug before leaving home. USING REMOTE CONTROL UNIT 7 Cautions on handling batteries Misuse of the batteries can result in electrolyte leakage, rupturing, corrosion, etc. Bear in mind the following points when using batteries. · Remove the batteries from the remote control unit if the unit is not going to be used for a prolonged period (a month or more). · Do not use an old battery together with a new one. · Insert the batteries while ensuring that their ª and · poles are properly aligned with the corresponding markings on the remote control unit. · Batteries with the same shape may have different voltages. Do not use different types of batteries together. · If electrolyte has leaked, thoroughly wipe the inside of the battery compartment, and then insert new batteries. · When batteries which are no longer required are to be discarded, follow the directions (regulations) laid down by the local authorities in the area concerned for their disposal. LOADING BATTERIES Batteries in this remote control unit have a life of approximately 1 year under normal operating conditions. If the remote control unit is not going to be used for an extended period of time, remove the batteries. Also, if you notice that the batteries are starting to run down, replace them as soon as possible. 7 Remote control Operate the remote control unit (RC4001CC) within a distance of approx. 5 m from the infrared signal reception window (remote sensor) on the front of the CD Changer. Remote control operation may not be possible if the remote control unit's transmitter is not pointing in the direction of the remote sensor or if there is an obstruction between the transmitter and the remote sensor. Remote control operating range Approx. 16.4 ft. (5m) 1 ENGLISH 7 Do not attempt repairs yourself · Refrain from lubricating the player: doing so can cause malfunctioning. · Only qualified engineers with specialized expertise are authorized to repair the pick-up and parts inside the player. q Remove the battery cover. 5 2 DISC CD CHAN GER 4 5 3 CC40 01 STAND DISC BY POWE R SKIP ON/ST ANDB Y OPEN /CLOS REPE AT PLAY RAND OM STOP E PAUS E LEVE L PRECAUTIONS · In winter, droplets of water form on the insides of the windows of a heated room: this is called condensation. This player uses an optical lens, so the condensation may form in the following cases. - In a room immediately after the heating has been turned on - In a room where the humidity level is high - When the player has been suddenly brought from a cold location into a warm room Since, in cases like this, the track numbers may not be read and the player is prevented from operating properly, wait about 30 minutes, and then operate the player. · This player may cause interference on a tuner or TV set. If this is the case, place it further away from the tuner or TV set. · Compact discs have much less noise than analog records and hardly any noise is heard before play starts. Bear in mind, therefore, that if the volume control on the amplifier is set too high, you will risk damaging other audio components. · Do not use commercially available lens cleaners, as they may damage the lens. PHON ES w Insert the batteries with correct ª /· orientation. Two AA-size batteries Remote control unit (RC4001CC) e Close the battery cover until it clicks shut. 4 NAMES AND FUNCTIONS FRONT PANEL /3 5 DISC CD CHANGER CC4001 1 MP3 CD PROGRAM R TRACK DISC TOTAL EACH REMAIN MIN SEC 12345 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 /4 v b /0 OPEN/CLOSE PLAY . STOP , PAUSE m 1 2 3 4 5 DISC SKIP 2 3 4 5 RANDOM REPEAT 1DISC REPEAT RANDOM LEVEL STANDBY POWER ON/STANDBY PHONES x z c /2 /1 n /5 /6 z POWER ON/STANDBY button When it is pressed, the display window lights up, and the power comes on. When it is pressed again, the display window is extinguished, and goes into the standby status. n 4/1, ¡/¢ (Track Skip/Search buttons) These buttons can be used as both track skip and track search buttons. (on the main unit only.) ¡/¢ : Each time this button is pressed, the track being played is skipped forward. When this button is continuously held down, tracks are searched forward (Fast Forward). 4/1 : When this button is pressed, the unit goes back to the beginning of the current track. If the button is pressed more times, the track being played is skipped back. When this button is continuously held down, tracks are searched backward (Fast Rewind). In program play, Fast Forward and Fast Rewind can be done in the playing track only. , 7 STOP button Press this button to stop playback. Also this button is used to clear programs. /3 1-5 (Disc Select button) Choose a disc to play. . 3 PLAY button Press this button to start playback. /4 DISC SKIP button When this button is pressed while multiple discs are placed on the tray, a disc to play can be chosen with rotating the tray clockwise. When this button is pressed while the tray is open, the turn table in the tray rotates so that the disc can be replaced. x STANDBY indicator Lights up in red color while standby status. /0 0 OPEN/CLOSE button Press this button to open the tray. Put on a disc with label side up. Press the button again to close the tray. c Disc tray The disc to be played is placed on the tray. /5 PHONES (headphones) jack The headphones are connected to this jack. Caution Close the tray by pressing the operation button, not by pressing it in with your hand. Caution Do not press the disc tray in by hand. This may cause malfunction. Caution Use headphones with a standard plug. v Remote sensor The infrared control signal emitted from the remote control unit is sensed here. /1 RANDOM button Playback tracks randomly. (See page 14) b Display window This screen shows the operating status. /2 REPEAT button Playback a track or disc repeatedly. Use this button also to switch to the Repeat mode (One Track Repeat, One Disc Repeat, and All Disc Repeat). (See page 15) /6 LEVEL (headphone volume) control This control is used to adjust the headphone volume. Turn it clockwise to increase the headphone volume. m 8 PAUSE button Press this button to pause playback. If pressed again, the unit returns to playback. 5 ENGLISH NAMES AND FUNCTIONS ENGLISH DISPLAY WINDOW a bcde 1 2 R TRACK DISC TOTAL EACH REMAIN MIN SEC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 MP3 CD PROGRAM f g h RANDOM REPEAT 1DISC n m 3 4 5 l a 3 (Play) indicator This lights during disc play. k j i l Remote Control indicator This lights during a remote control unit is operated. h REMAIN indicator This lights while displaying track and disc remaining times. b 8 (Pause) indicator This lights when play is paused. i 1-20 (track number display) Displays the number of tracks recorded in a disc, the number of remaining tracks, and the number of tracks programmed with program play. · Cannot display more than 20 tracks. m Disc Number indicator Displays the disc number chosen. c MP3 indicator This lights during MP3 play. n Disc indicator Displays the disc numbers on the tray. d CD indicator This lights during Audio CD play. j Time indicator Displays the time. e PROGRAM indicator This lights during program play. k Track Number indicator Displays the track number chosen. f RANDOM indicator This lights during random play. g REPEAT indicator This lights during repeat play. 6 NAMES AND FUNCTIONS REAR PANEL ENGLISH REMOTE CONTROL IN EXT. INT. RS-232C OUT R COAXIAL OPTICAL ANALOG OUT L DIGITAL OUT FLASHER IN AC IN MODEL NO. CC4001 AB C D E FG H A EXT./INT. (External/Internal switch) When this unit is used as a standalone component, set this switch to the INT. side. When it is used connected to external component by a remote connecting cable and to audio component with a remote sensor that supports remote controls by Marantz, set this switch to the EXT. side. C REMOTE CONTROL IN/OUT (input and output) connectors When the remote control connectors on the unit and on a Marantz AV component are connected using the accessory remote connecting cables, the components can be operated as a system by remote control. · When connecting to a component which is equipped with remote control connectors, the unit's REMOTE CONTROL IN connector must always be connected to the REMOTE CONTROL OUT connector on the other component to be connected. · When connecting a component which is not equipped with an infrared remote sensor, this component must always be connected to the unit's REMOTE CONTROL OUT connector. D ANALOG OUTPUT connectors These are the output jacks of the analog audio signals. The supplied analog connection cord can be connected to the CD, AUX, or other connectors on an amplifier. Be sure to connect the L and R channels correctly to the corresponding jacks. F DIGITAL AUDIO OUT OPTICAL This jack is to be connected with a recording device, amplifier, D/A converter, etc that has optical digital input using an optional square type optical digital cable. G Flasher Input jack A control port for professionals (custom installers). This is used to control the unit from other rooms using keypad, etc. Caution Never connect to the PHONO connector on the amplifier. Caution If the unit is used as standalone and the switch is set to EXT. position, remote control unit cannot be used. E DIGITAL AUDIO OUT COAXIAL This jack is to be connected with a recording device, amplifier, D/A converter, etc that has coaxial digital input using an optional coaxial digital cable. H AC Inlet Connect the supplied power cord to this jack and a household AC power outlet. B RS-232C External Control Port A control port for professionals (custom installers). 7 NAMES AND FUNCTIONS ENGLISH REMOTE CONTROLLER z ON button n 1, ¡ (Search buttons) 1: ¡: While this button is pressed during playback, the track is searched backward. While this button is pressed during playback, the track is searched forward. /4 RECALL button Use this button to check the programmed tracks while programming or stopped programming. (See page 16) z x c STANDBY ON When this button is pressed while the unit is in standby status, the power of the unit is turned on. OPEN/CLOSE TIME DIMMER /7 /6 x STANDBY button When this button is pressed while the power is on, the unit goes into the standby status. /5 0 -9 (Numerical buttons) Use these buttons to choose tracks and to input track number in each mode. 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL m RANDOM button Playback tracks randomly. (See page 14) c 0 OPEN/CLOSE button /6 TIME button This button is used to switch the time display. Each time it is pressed, the displayed time cycles from "track elapsed time" "track remaining time" "total remaining time" "track elapsed time". (See page 18) /5 /4 /3 /2 Press this button to open the tray. Put on a disc with label side up. Press the button again to close the tray. , DISC1-DISC5 (Disc Select button) Choose a disc to play. v Caution Do not press the disc tray in by hand. This may cause malfunction. . REPEAT button Playback a track or disc repeatedly. Use this button also to switch to the Repeat mode (One Track Repeat, One Disc Repeat, and All Disc Repeat). (See page 15) /7 DIMMER button This button is used to adjust the brightness of the display window. v PROGRAM button This button is for program play. (See page 15) b /1 n m , RANDOM AMS REPEAT b 4, ¢ (Track Skip buttons) 4: When this button is pressed, the unit goes back to the beginning of the current track. If the button is pressed more times, the track being played is skipped back. ¢: Each time this button is pressed, the track being played is skipped forward. · Search buttons are provided separately for the remote control unit. Use n Search buttons for search function. /0 AMS (Automatic Music Scan button) Use this button for AMS play. (See page 13) /0 . /1 7 STOP button Press this button to stop playback. Also this button is used to clear programs. DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 /2 8 PAUSE button Press this button to pause playback. If pressed again, the unit returns to playback. REMOTE CONTROLLER RC4001CC /3 3 PLAY button Press this button to start playback. 8 NAMES AND FUNCTIONS REMOTE CONTROL CODE SETTING · The unit and remote control unit have five sets of built-in remote control codes for each. These codes enable up to five CC4001s installed in the same place to be controlled independently. · To use multiple units at the same time, set the second, third, forth, and fifth CC4001s and their remote control units' remote control codes. · To set the codes, follow the procedure below to control only selected unit is remotely controlled. · At the factory, the unit and remote control unit were set to CODE1. 7 Remote Control Unit Setting STANDBY ON 7 CC4001 Setting STANDBY ON Display Examples · When the remote control unit is set to CODE1 1 2 CD OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER 3 4 DISC 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL 1-5 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL 5 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 RECALL PROGRAM RECALL · When the remote control unit is set to CODE2 1 2 3 4 5 DISC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 CD RANDOM AMS REPEAT RANDOM AMS REPEAT DISC 1 DISC 2 DISC 3 DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 4 DISC 5 · When the remote control unit is set to CODE3 REMOTE CONTROLLER RC4001CC REMOTE CONTROLLER RC4001CC 1 2 3 CD · To set CODE2 Press RECALL button and Numerical button 2 on the remote control unit at a time for five seconds or more. · To set CODE3 Press RECALL button and Numerical button 3 on the remote control unit at a time for five seconds or more. · To set CODE4 Press RECALL button and Numerical button 4 on the remote control unit at a time for five seconds or more. · To set CODE5 Press RECALL button and Numerical button 5 on the remote control unit at a time for five seconds or more. · To synchronize the remote control code of the CC4001 with the remote control unit, press the PROGRAM and RECALL buttons on the remote control unit together. · The remote control code set is displayed on the display window for two seconds, and the setting is completed. DISC 4 5 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 · When the remote control unit is set to CODE4 1 2 3 4 5 DISC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 CD · When the remote control unit is set to CODE5 1 2 3 4 5 DISC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 CD Caution To reset the remote control to CODE1, press RECALL button and Numerical button 1 on the remote control unit at the same time for five seconds or more. 9 ENGLISH CONNECTIONS ENGLISH Depending on your amplifier/receiver/Stereo System, there are various ways to connect to this player. For correct connection please refer to instruction manuals of stereo system to be connected. To Analog Audio output (white) (red) Caution Do not connect audio output from this unit to PHONO input of your audio system. 1. 2. Connect the audio cable q to this unit's Analog Audio outputs and the stereo inputs on your amplifier, receiver or stereo system. Connect the optical cable w, coaxial cable e to the digital input on your AV amplifier, D/A converter, CD Recorder, etc. REMOTE CONTROL IN EXT. INT. EXT INT RS-232C RS 232C OUT ANALOG OUT L DIGITAL DIGITAL OUT FLASHER IN R COAXIAL OPTICAL AC IN MODEL NO. CC4001 To Digital Audio output w (Optional) e (Optional) Audio cable q (Supplied) To audio input terminals on amplifier INTEGRATED AMPLIFIER INPUT SELECTOR VOLUME PHONO CD TUNER AUX/DVD 1 RECORDER 2 Connect to digital input terminals of AV amplifier, D/A converter or CD recorder, etc.. MUTE PROTECT REC SELECTOR OFF POWER ON/OFF PHONES BASS TREBLE BALANCE MIN SPEAKERS MAX SOURCE DIRECT TUNER AUX/DVD RECORDER 21 COPY RECORDER2 1 2 CD PHONO ON OFF ON OFF