User manual MARANTZ PM7001

Model PM7001 User Guide Integrated Amplifier CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shockto persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacture's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Additional Safety Information! · This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. · Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. · When the switch is in the OFF position, the apparatus isn't completely switched-off from the MAINS. CONTENTS BEFORE USE ........................................................................................................................................ 1 FEATURES ............................................................................................................................................ 2 BEFORE MAKING CONNECTIONS ..................................................................................................... 3 WIRING SPEAKER CABLE ................................................................................................................................ 3 BI-WIRING CONNECTION ................................................................................................................................. 3 ENGLISH CONNECTIONS .................................................................................................................................... 4 NAMES AND FUNCTIONS OF PARTS ................................................................................................. 6 FRONT PANEL ................................................................................................................................................... 6 REAR PANEL ..................................................................................................................................................... 7 RC4001PM REMOTE CONTROLLER ................................................................................................................ 8 BASIC OPERATION ............................................................................................................................ 11 PLAYBACK ........................................................................................................................................................ 11 RECORDING .................................................................................................................................................... 11 HOW TO USE AND SET FEATURES .................................................................................................. 12 MAIN IN JACKS ................................................................................................................................................ 12 REMOTE CONTROL JACKS ............................................................................................................................ 13 TROUBLESHOOTING ......................................................................................................................... 14 OTHERS .............................................................................................................................................. 15 SPECIFICATIONS & DIMENSIONAL DRAWINGS .............................................................................. 15 This section must be read before any connection is made to the mains supply. 7 Do Not Touch Hot Spots During and Immediately After Use During and immediately after use, the PM7001 is hot in areas other than the controls and rear panel connection jacks. Do not touch hot spots and especially the top panel. Contact with hot areas can cause burns. 7 EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. PM7001 can be powered by 120V AC only. 7 Battery Handling Improper use of dry cell batteries can result in electrolyte leaks, rupture and corrosion. Read the following precautions before use. · If not planning to use the remote controller for an extended period of 1 month or more, remove the batteries. · Do not mix old batteries with new batteries. · Load batteries in the proper direction indicated on the remote controller. · Do not mix batteries of differing type. Even batteries of the same shape and size can have differing voltages. · If batteries leak, wipe the case clean of any adhering electrolyte and replace the old batteries with new batteries. 7 COPYRIGHT Recording and playback of any material may require consent. For further information refer to the following: -- Copyright Act 1956 -- Dramatic and Musical Performers Act 1958 -- Performers Protection Acts 1963 and 1972 -- Any subsequent statutory enactments and orders 7 Do Not Locate in the Following Places To ensure long-lasting use, do not locate the PM7001 where: · Exposed to direct sunlight. · Near to sources of heat such as heaters. · Highly humid or poorly ventilated. · Dusty. · Subjected to mechanical vibrations. · On wobbly, inclined or otherwise unstable surfaces · Radiated heat is blocked such as in cramped audio racks. To ensure proper heat radiation, ensure the below clearance from walls and other equipment. Left 7-7/8 ins. (0.2 m) or more Above 7-7/8 ins. Right 7-7/8 ins. (0.2 m) or more (0.2 m) or more 7 Accessories Check Before use, check the below accessories were included in the package. · AC power cable The power cable included in the package can be used with the PM7001 only. It cannot be used with other equipment. · RC4001PM remote controller · AA-size batteries x 2 Rear 7-7/8 ins. (0.2 m) or more 7 Keep Objects Off Keep objects off the PM7001. Blocking the vent can result in accident and damage. · Registration Card · User Guide (This manual) 1 ENGLISH BEFORE USE FEATURES ENGLISH INTEGRATED AMPLIFIER PM7001 INPUT SELECTOR VOLUME PHONO CD TUNER AUX/DVD 1 RECORDER 2 MUTE STANDBY REC SELECTOR OFF POWER ON/OFF PHONES BASS TREBLE BALANCE 1 MIN SPEAKERS 2 MAX SOURCE DIRECT TUNER AUX/DVD RECORDER 21 COPY RECORDER2 1 2 CD PHONO ON OFF ON OFF - + - + L R The PM7001 is an integrated amplifier developed on the design concepts of Marantz's PM-11S1 high-end model amplifier. · Short Power Line Layout In order to improve the momentary-current supply capability, a new layout which places priority on making the large current line connections as short as possible was adopted. In this layout the power supply circuit, main-amplifier output stage, and heatsink are unified, and the large current line is arranged to be as short as possible while still achieving symmetry on the left and right sides. · CD Direct Buffer Amplifier The PM7001 incorporates a specialized input buffer amplifier nearby the CD input jack. This buffer amplifier faithfully transmits the CD input jack signal by preventing interference from between the left and right channels, and from the effects of other circuits. A discrete configuration high-speed buffer amplifier which is built on the HDAM ®SA technology is incorporated into the buffer amplifier circuit. · Current Feedback Amplifier Both pre-amplifier and main-amplifier incorporate a high-speed current feedback amplifier circuit, which faithfully amplify signals from the CD player. Moreover, the high-speed current feedback amplifier reproduces a natural sound field space. · CD Direct Selector The output of CD direct buffer amplifier has a specialized relay switch, which directly transmits the input signal by the shortest path to the pre-amplifier. · Improved Momentary-Current Supply Capability It is known that sound quality differs between amplifiers that use the same spec, and Marantz believes that this is caused by differences in speaker drive capability. The PM7001 mainamplifier has the capability to momentarily pass 25 amperes or more of current, providing high-powered drive to the speakers. 2 WIRING SPEAKER CABLE · Be careful not to short circuit in wiring speaker cables. · Peel off the corting of speaker cable as shown below. Approx. 7/16 ins. (10 mm) Here following is explained BI-WIRING connection that improve sound quality. The speakers in this explanation have low and mid/high input jacks that support a BI-WIRING connection. To determine whether or not your speakers support a BI-WIRING connection, check in the instruction manual that came with your speakers or contact the manufacturer. Cut the corting of cable. Peel off the edge of cable. Twist conductors. BI-WIRING CONNECTION A bi-wiring connection separately connects the low and mid/ high jacks of the speaker to the amplifier using separate speaker cables. Because separate cables are used for low and mid/high sounds, the kick back current in the low speaker causes little interference with the mid/high speaker. The PM7001 and speakers of Connection Example 1 (pg. 5) use a bi-wiring connection, therefore also refer to that page for help. · Wiring with speaker cable. Turn counter-clockwise to loosen. Insert conductor of cable. Turn clockwise to tighten. CD player, etc. PM7001 Bi-wiring Speaker system connection Mid/high speaker Band pass filter Low speaker Your speaker system must satisfy the below conditions. If it does not, the PM7001's protective circuit will active, whereby preventing proper playback. In some cases, the amplifier and speakers may be damaged. · If using 1 set of speakers, total speaker impedance must be 4 or more. · If using 2 sets of speakers, total speaker impedance must be 8 or more. 3 ENGLISH BEFORE MAKING CONNECTIONS CONNECTIONS Connection Example : Basic Connection for Stereo Playback Refer also to the instruction manuals of components to connect equipment correctly. ENGLISH Record Player To LINE OUT jacks CD player L PHONO PRE OUT MAIN IN GND L L To LINE OUT jacks R R R CD TUNER Tuner L R AUX / DVD RECORDER 1 IN OUT RECORDER 2 IN OUT L SYSTE SYSTE SEPARATE R To LINE OUT jacks ON OFF DVD Player To LINE OUT jacks CD-R, etc. To LINE IN jacks To LINE OUT jacks MD or Tape deck, etc. To LINE IN jacks 4 Speaker Main-amplifier Speaker If you have another mainamplifier, you can use the PM7001 as the pre-amplifier by connecting as shown in the diagram below. POWER ON/OFF To input jacks To power outlet PHONO PRE OUT MAIN IN SPEAKERS R L SYSTEM 1 L MODEL NO. PM7001 GND L L R R R AC IN SYSTEM 2 SERIAL NO. CD TUNER AUX / DVD RECORDER 1 IN OUT RECORDER 2 IN OUT IN L L REMOTE CONTROL SYSTEM 1 OR SYSTEM 2 4 -16 OHMS SYSTEM 1 AND SYSTEM 2 8 -16 OHMS SEPARATE OUT R R ON OFF Set to "OFF" MF / HF MF / HF LF LF Remove shorting bar. L CH speaker Remove shorting bar. Remove shorting bar. R CH speaker Remove shorting bar. · Use a bi-wiring connection (pg. 3) for speakers. · Set the SPEAKERS button 1 and button 2 on the front panel in the ON position. 5 ENGLISH CONNECTIONS NAMES AND FUNCTIONS OF PARTS FRONT PANEL qw e INPUT SELECTOR ENGLISH r INTEGRATED AMPLIFIER PM7001 t y u VOLUME PHONO CD TUNER AUX/DVD 1 RECORDER 2 MUTE STANDBY REC SELECTOR OFF POWER ON/OFF PHONES BASS TREBLE BALANCE 1 MIN SPEAKERS 2 MAX SOURCE DIRECT TUNER AUX/DVD RECORDER 21 COPY RECORDER2 1 2 CD PHONO ON OFF ON OFF - + - + L R !4 !3 !2 !1 !0 o i q POWER ON/OFF button Pressing this button once turns power to the amplifier ON, and pressing it again turns power to the amplifier OFF. When the button is in the ON position, power can be switched ON/OFF using the supplied remote controller. If the power is switched OFF using the remote controller, the amplifier engages in standby mode. When in this mode, you cannot switch the power ON by pressing the POWER ON/OFF button q. The amplifier remains in standby mode even if this button is pressed. To switch the power ON, either turn the INPUT SELECTOR knob e or press the MAIN POWER ON button z on the remote controller. u VOLUME knob Turning this knob clockwise increases the volume, while turning it counterclockwise decreases the volume. The volume can also be adjusted using the remote controller. If the amplifier's protective circuit activates, the VOLUME knob u automatically turns for approx. 15 seconds and the volume decreases. i SOURCE DIRECT button When this button is pressed in, the audio signal is transmitted bypassing the balance and tone control circuits, allowing you to enjoy a higher level of sound quality. w STANDBY indicator This indicator is lit red when the amplifier is in standby mode. When in standby mode, you can switch the power ON by using the MAIN POWER ON button z on the remote controller. If the amplifier's protective circuit activates, this indicator flashes and the amplifier's power automatically shuts off. o SPEAKERS 1/2 buttons These buttons turn the speaker output to the speakers connected to the SPEAKERS SYSTEM 1 and 2 terminals E on the rear panel ON and OFF. When listening with headphones, turn the speaker output OFF. e INPUT SELECTOR knob This knob selects the input source for playback. The selected input source is displayed on the function indicator. The amplifier memorize the selected input source when the power is turned OFF, and then re-selects the same input source when the power is turned ON again. !0 BALANCE knob This knob is used to adjust the sound level from one of either the L (left) or R (right) channels. If the BALANCE knob !0 is turned all the way round to one side, sound is not output from the opposite side. Please note that this knob does not function when the SOURCE DIRECT button i is in the ON position. r MUTE indicator When the MUTE button c on the remote controller is pressed, the MUTE function is activated and the volume is lowered. Pressing the MUTE button c again releases the MUTE function. Moreover, the MUTE function can also be released by pressing the VOLUME 3/4 button c on the remote controller. If the amplifier's protective circuit activates, this indicator flashes for approx. 15 seconds and the MUTE function activates. While this indicator is flashing, the VOLUME knob u automatically turns and the volume decreases. !1 Tone Control knobs (BASS/TREBLE) These knobs are used to adjust the BASS and TREBLE sound level. Turning the knobs clockwise increases the sound level, and turning them counterclockwise decreases the sound level. Please note that these knobs do not function when the SOURCE DIRECT button i is in the ON position. !2 REC SELECTOR knob This knob switches the input sources for recording. Moreover, you can connect a tape deck, CD-R player, and other such device to the RECORDER 1 and 2 terminals I J to make copies. We recommend the knob be set to the OFF position when not recording to obtain optimal sound quality. (See page 11.) t Function indicator This indicator displays the input source currently selected by the INPUT SELECTOR knob e. y Power indicator This indicator is lit a blue color while power to the PM7001 is ON. 6 !3 Infrared Receptor Window This is the receptor of control signals sent from the RC4001PM remote controller. Point the remote controller towards this window to properly transmit signals. !4 PHONES jack This jack is for connecting headphones with a standard stereo plug. To listen with headphones, turn the speaker output OFF by setting the SPEAKERS 1 and 2 buttons o in the OFF position. REAR PANEL A PHONO B CD PRE OUT MAIN IN E SPEAKERS F L MODEL NO. PM7001 R L SYSTEM 1 GND L L R R R AC IN SYSTEM 2 SERIAL NO. CD TUNER AUX / DVD RECORDER 1 IN OUT RECORDER 2 IN OUT IN L L REMOTE CONTROL SYSTEM 1 OR SYSTEM 2 4 -16 OHMS SYSTEM 1 AND SYSTEM 2 8 -16 OHMS SEPARATE OUT R R ON OFF ML K J I H G A PHONO Input jacks These jacks are for connecting to an analog record player. MM cartridges can be used. H SEPARATE switch This switch is used for selecting the pre-amplifier and mainamplifier connection modes. OFF: Select this position when the amplifier is used as a normal integrated amplifier. (Standard factory setting) ON: The pre-amplifier and main-amplifier are separated. The PM7001 can be used as a main-amplifier when input is connected to the MAIN IN jacks D. B PHONO GND terminal Connect the grounding wire from an analog record player. C PRE OUT jacks These jacks are for connecting to the input jacks of another main-amplifier or active subwoofer. I RECORDER 1/RECORDER 2 output jacks These jacks are for connecting to the recording input jacks of a CD-R recorder, MD deck, tape deck, etc. Output signals can be selected using the REC SELECTOR knob !2 on the front panel. D MAIN IN jacks These jacks are for connecting to the output terminals of another pre-amplifier when using the PM7001 as the mainamplifier. In this case, set the SEPARATE switch H to the ON position. J RECORDER 1/RECORDER 2 input jacks These jacks are for connecting to the output jacks of a CDR player, MD deck, tape deck, etc. E SPEAKERS SYSTEM 1, 2 output terminals You can connect 2 speaker systems, SPEAKERS 1 and SPEAKERS 2 E. Speaker output can be turned ON/OFF from the SPEAKERS 1 and 2 buttons o on the front panel. K AUX/DVD input jacks These jacks are for connecting to the output jacks of a DVD player or other LINE component. F AC IN socket Connect the supplied AC power cable to this socket and a power outlet. L TUNER input jacks These jacks are for connecting to the output jacks of a tuner or other LINE component. G REMOTE CONTROL jacks These jacks are for connecting to other Marantz components such as a CD player or DVD player that has a remote control connector (D.BUS jack). You can use the remote controller supplied with the PM7001 to control the system. For more details, see page 13. M CD input jacks These jacks are for connecting to the output jacks of a CD player or similar component. 7 ENGLISH NAMES AND FUNCTIONS OF PARTS NAMES AND FUNCTIONS OF PARTS ENGLISH RC4001PM REMOTE CONTROLLER Using this remote controller, you can control the PM7001 and Marantz CD players, DVD players, tuners, tape decks etc. that have a remote control receptor. The operations possible by remote controller may differ with each component; therefore see the instruction manual that came with the component. (See page 13) The RC4001PM remote controller buttons are laid out as shown below. z Power ON/OFF buttons · MAIN POWER ON button This button switches the power ON when the PM7001 is in STANDBY mode. · MAIN POWER OFF button This button switches the PM7001 to STANDBY mode when the power is ON. · SOURCE POWER button This button switches between power ON and STANDBY modes for Marantz products that have a standby function. By pressing this button after one of the buttons in the button group x, you can switch the power between ON and STANDBY modes for the Marantz product that corresponds to that button. By pressing this button after the AMP button x, you can switch the PM7001 between power ON and STANDBY modes. z x x Input selector buttons This group of buttons is used for selecting the input source. Caution In the PM7001, AUX and DVD, and RECORDER 2's TAPE and MD each share the same input jacks. The signal codes for controlling these Marantz products using the RC4001PM differ, therefore separate buttons have been built into the remote controller. c VOLUME adjustment buttons v · MUTE Button This button activates the mute function. Pressing this button again releases the MUTE function. The MUTE function can also be released by pressing either the VOLUME 3 or 4 buttons c. · VOLUME 3 Button This button increases the volume level. · VOLUME 4 Button This button decreases the volume level. c v Component operating buttons These buttons are for performing basic operations of a Marantz CD player, DVD player, etc. The function of each button changes to match the component selected as the input source using the input selector buttons x. 8 7 CD When the CD button x is pressed, the buttons in group v function as indicated in the table below. These buttons can only be used when a Marantz CD player is connected to the CD input jacks M. BUTTON NAME F/P -/-MODE MEMO SCROLL CANCEL TEXT (MODE ) TIME (MODE ) 1-9 0 ­ FUNCTION None Disc Select Auto Music Scan (AMS) Program Scroll/Recall Program Cancel Text Time 1-9 0 Previous Track Next Track Play Previous Track Next Track Fast Reverse Fast Forward Stop None Pause Open/Close 7 DVD When the DVD button x is pressed, the buttons in group v function as indicated in the table below. These buttons can only be used when a Marantz DVD player is connected to the AUX/DVD input jacks K. BUTTON NAME F/P -/-MODE MEMO SCROLL CANCEL TEXT (MODE ) TIME (MODE ) 1-9 0 ­ FUNCTION Disc Skip Disc Skip None None None None Audio OSD 1-9 0 Previous Chapter Next Chapter Play Previous Chapter Next Chapter Scan ­ Scan + Stop None Pause Open/Close + 2 4 ¢ 1 ¡ 7 12 8 OPEN/CLOSE + 2 4 ¢ 1 ¡ 7 12 8 OPEN/CLOSE 7 TUNER When the TUNER button x is pressed, the buttons in group v function as indicated in the table below. These buttons can only be used when a Marantz tuner is connected to the TUNER input jacks L. BUTTON NAME F/P -/-MODE MEMO SCROLL CANCEL TEXT (MODE ) TIME (MODE ) 1-9 0 ­ FUNCTION Frequency Direct Preset 10 T-mode (Stereo/Mono) Memo Display Cancel Preset Scan IF Band Preset 1 - Preset 9, 1 - 9 0 Preset Down Preset Up None None None Tuning Down Tuning Up None None None None 7 TAPE When the RECORDER 2 (TAPE) button x is pressed, the buttons in group v function as indicated in the table below. These buttons can only be used when a Marantz tape deck is connected to the RECORDER 2 (TAPE) jacks I. BUTTON NAME F/P -/-MODE MEMO SCROLL CANCEL TEXT (MODE ) TIME (MODE ) 1-9 0 ­ FUNCTION Deck A Deck B None None None Counter Reset None Time/Display None None Back Skip Forward Skip Play Back Skip Forward Skip Fast Rewind Fast Forward Stop Direction Pause Eject + 2 4 ¢ 1 ¡ 7 12 8 OPEN/CLOSE + 2 4 ¢ 1 ¡ 7 12 8 OPEN/CLOSE 9 ENGLISH NAMES AND FUNCTIONS OF PARTS NAMES AND FUNCTIONS OF PARTS ENGLISH 7 For use of Remote controller · Loading batteries Before using the remote controller for the first time, load the batteries in the remote controller. The batteries provided are used to verify the operations of the remote controller only. 7 Operatable range of Remote controller Operate the remote controller (RC4001PM) within a distance of approx. 5m from the infrared receptor window on the front of the PM7001. 1. Remove the battery cover which is found on the back side of the remote controller. Approx. 16.4 ft. (5m) 60° 2. Load the two new size "AA" batteries inside the battery compartment while taking care to align their polarities correctly with the polarity markings ( with and with ). Remote controller (RC4001PM) · Caution · Do not allow direct sunlight, an inverter fluorescent light or other strong source of light to shine onto the player's infrared receptor window. Otherwise, the operation of the remote controller may be disabled. Bear in mind that operating the remote controller may cause other devices operated by infrared rays to be operated by mistake. The remote controller cannot be operated if the space between the controller and the player's infrared reseptor window is obstructed. Do not place any objects on top of the remote controller. Doing so may cause one or more buttons to be held down which will cause the batteries to run down. · · · 3. Push the cover on the back side in the direction of the arrow to close. 10 PLAYBACK To explain how to play back input sources, representative examples are given with an CD player and analog record player. Before starting either procedure, check the component is correctly connected to the PM7001. RECORDING This example explains how to record from an input source such as an CD player to a recording device such as a CD-R. 1. Press the power ON/OFF switch of the CD player and CDR to activate power to both components. 7 Disc Playback on an CD Player 1. Press the power ON/OFF button of the CD player to activate power to it. 2. Press the POWER ON/OFF switch q to activate power to 3. 4. 5. it. Approximately 8 seconds after power has been activated, the muting turns OFF and audio output is enabled. Select the CD with the REC SELECTOR knob !2. If you want to listen to the recording source through the speakers, set the INPUT SELECTOR knob e to the CD position. Load a playback disc into the CD player and a recording disc into the CD-R. Start playback on the CD player. Then, start recording on the CD-R. 2. Press the POWER ON/OFF button q to activate power to 3. 4. 5. 6. 7. it. Approximately 8 seconds after power has been activated, the muting turns OFF and audio output is enabled. Select the CD from the INPUT SELECTOR knob e. To use the speakers connected to the SPEAKERS SYSTEM terminals, press the SPEAKERS button 1 and 2 o. Load a disc into the CD player and press the play button to start playback. Adjust the volume level from the VOLUME knob u. Adjust bass/treble as desired from the BASS and TREBLE knobs !1. Be sure to first set the SOURCE DIRECT button i in the OFF position. 7 Disc Playback on an Analog Record Player 1. Press the POWER ON/OFF switch q to activate power to 2. it. Approximately 8 seconds after power has been activated, the muting turns OFF and audio output is enabled. Select "PHONO" as the input source from the INPUT SELECTOR knob e. To prevent unexpected accidents, it is recommended to set the volume level to MIN. by turning the VOLUME knob u until muting the volume level. MM type cartridges can be connected. Use a step-up transformer when using an MC cartridge. To use the speakers connected to the SPEAKERS SYSTEM terminals, press the SPEAKERS button 1 and 2 o. Set a record on the analog record player and play it. Adjust the volume level from the VOLUME knob u. Adjust bass/treble as desired from the BASS and TREBLE knobs !1. Be sure to first set the SOURCE DIRECT button i in the OFF position. About the REC SELECTOR The REC SELECTOR knob !2 can be operated independently, irrespective of the input source selected using the INPUT SELECTOR knob e. OFF: Cannot record because no signal is output to the RECORDER 1, 2 jacks. PHONO, CD, TUNER, AUX/DVD: Selects the program source for recording. COPY RECORDER 1-2: Select this to copy the RECORDER 1 signal onto RECORDER 2. COPY RECORDER 2-1: Select this to copy the RECORDER 2 signal onto RECORDER 1. 3. 4. 5. 6. 7. q e INTEGRATED AMPLIFIER PM7001 INPUT SELECTOR VOLUME PHONO CD TUNER AUX/DVD 1 RECORDER 2 MUTE STANDBY REC SELECTOR OFF POWER ON/OFF PHONES BASS TREBLE BALANCE 1 MIN SPEAKERS 2 MAX SOURCE DIRECT TUNER AUX/DVD RECORDER 21 COPY RECORDER2 1 2 CD PHONO ON OFF ON OFF - + - + L R !2 q e INTEGRATED AMPLIFIER PM7001 INPUT SELECTOR PHONO CD TUNER AUX/DVD 1 RECORDER 2 u VOLUME MUTE STANDBY REC SELECTOR OFF POWER ON/OFF PHONES BASS TREBLE BALANCE 1 MIN SPEAKERS 2 MAX SOURCE DIRECT TUNER AUX/DVD RECORDER 21 COPY RECORDER2 1 2 CD PHONO ON OFF ON OFF - + - + L R !1 o i 11 ENGLISH BASIC OPERATION HOW TO USE AND SET FEATURES MAIN IN JACKS You can separate the pre-amplifier section and main-amplifier section by using the SEPARATE switch settings on the PM7001. If you have another pre-amplifier, you can use the PM7001 as the main-amplifier by connecting as shown in the diagram below. Pre-amplifier ENGLISH To PRE OUT Jacks To power outlet Set the SPEAKERS 1 and 2 button on the front panel to the ON position. PHONO PRE OUT MAIN IN SPEAKERS R L SYSTEM 1 L MODEL NO. PM7001 GND