User manual MARANTZ SR9200

R Model SR9200 User Guide AV Surround Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (Cable-TV) system installer's attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture ­ Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. Accessories ­ Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 14. AC POLARIZED PLUG 13. Power-Cord Protection ­ Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Protective Attachment Plug ­ The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug. Outdoor Antenna Grounding ­ If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1. Lightning ­ For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. Power Lines ­ An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Overloading ­ Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Object and Liquid Entry ­ Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 12. Grounding or Polarization ­ This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 2. 3. 4. 5. 6. 7. 8. 15. 9. 16. 10. Ventilation ­ Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Power Sources ­ This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 17. 18. 11. 19. i 20. Servicing ­ Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service ­ Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or plug is damaged. 22. Replacement Parts ­ When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check ­ Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Wall or Ceiling Mounting ­ The product should be mounted to a wall or ceiling only as recommended by the manufacturer. Heat ­ The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 21. 23. a. b. c. d. 24. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way, and When the product exhibits a distinct change in performance ­ this indicates a need for service. 25. e. f. FIGURE 1 EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC - NATIONAL ELECTRICAL CODE This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. ii FEATURES .................................................... 2 AMPLIFIER FEATURES ............................................................................... 2 AUDIO/VIDEO FEATURES .......................................................................... 2 FLEXBILITY FEATURES .............................................................................. 2 OTHER FEATURES ..................................................................................... 2 BASIC OPERATION (PLAY BACK) ............ 33 SELECTING AN INPUT SOURCE. ............................................................. 33 SELECTING THE SURROUND MODE ...................................................... 33 ADJUSTING THE MAIN VOLUME ............................................................. 33 ADJUSTING THE TONE(BASS & TREBLE) CONTROL. ........................... 33 TEMPORARILY TURNING OFF THE SOUND ........................................... 34 USING THE SLEEP TIMER ........................................................................ 34 NIGHT MODE ............................................................................................. 34 DIALOGUE NORMALIZATION MESSAGE ................................................ 34 DESCRIPTION ............................................... 3 FRONT PANEL .............................................. 5 FL DISPLAY ................................................... 7 REAR PANEL ................................................ 9 REMOTE CONTROL UNIT RC3200A ......... 11 LOADING BATTERIES ............................................................................... 11 ACTIVATING THE RC3200A ...................................................................... 11 OPERATING DEVICES .............................................................................. 12 REMOTE-CONTROLLABLE RANGE ......................................................... 12 OPERATING AMP & TUNER ...................................................................... 13 SHOW THE STATUS OF SR9200 ON THE LCD OF RC3200A ................. 15 WORKING WITH MODES .......................................................................... 16 ADJUSTING THE SETTINGS .................................................................... 16 LEARNING COMMANDS ........................................................................... 18 RECORDING MACROS ............................................................................. 18 RC3200 EDIT .............................................................................................. 20 IMPORTANT NOTICES .............................................................................. 21 CLEANING RC3200A ................................................................................. 21 HOW TO RESET THE RC3200A ................................................................ 21 SURROUND MODE ..................................... 35 OTHER FUNCTION ..................................... 39 TV AUTO ON/OFF FUNCTION .................................................................. 39 ATTENUATION TO ANALOG INPUT SIGNAL ............................................ 39 LISTENING OVER HEADPHONES ............................................................ 39 VIDEO ON/OFF .......................................................................................... 39 DISPLAY MODE ......................................................................................... 39 SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT ........... 39 RECORDING AN ANALOG SOURCE ........................................................ 40 RECORDING A DIGITAL SOURCE ............................................................ 40 7.1 CH INPUT. ............................................................................................ 41 AUX2 INPUT ............................................................................................... 41 BASIC OPERATION (TUNER) .................... 42 LISTENING TO THE TUNER ...................................................................... 42 PRESET MEMORY ..................................................................................... 42 MULTI ROOM SYSTEM ............................... 44 MULTI ROOM PLAYBACK USING THE MULTI ROOM OUT TERMINALS .... 44 MULTI ROOM PLAYBACK USING THE MULTI SPEAKER TERMINALS ...... 44 OPERATION TO MULTI ROOM OUTPUTS WITH THE REMOTE CONTROLLER FROM SECOND ROOM. .................................................. 44 CONNECTING ............................................. 22 CONNECTING THE AUDIO COMPONENTS ............................................. 22 CONNECTING THE VIDEO COMPONENTS ............................................. 22 CONNECTING THE VIDEO COMPONENTS WITH S-VIDEO / COMPONENT ... 23 CONNECTING THE MONITOR AND VIDEO CAMERA ............................. 23 CONNECTING THE DIGITAL / 7.1CH INPUT ............................................ 24 CONNECTING THE SPEAKERS ............................................................... 24 CONNECTING THE SPEAKERS WITH EXTERNAL AMPLIFIER ............. 25 CONNECTING THE ANTENNA AND POWER CORD ............................... 25 CONNECTING THE REMOTE CONTROL BUS (RC-5) ............................. 26 CONNECTING FOR THE MULTI ROOM ................................................... 26 TROUBLESHOOTING ................................. 46 SETUP ......................................................... 27 ON SCREEN DISPLAY MENU SYSTEM ................................................... 27 INPUT SETUP (ASSIGNABLE DIGITAL INPUT) ........................................ 28 SPEAKER SETUP ...................................................................................... 28 PREFERENCE ........................................................................................... 30 SURROUND ............................................................................................... 31 PL2 (PRO LOGIC II) MUSIC PARAMETER ............................................... 31 MULTI ROOM ............................................................................................. 32 7.1 CH INPUT LEVEL ................................................................................. 32 DC TRIGGER SETUP ................................................................................ 32 1 ENGLISH TABLE OF CONTENTS FEATURES AMPLIFIER FEATURES · THX Ultra certified 7ch amplifiers have enough power for even the most difficult conditions found in large rooms. Enormous power reserves endow the system with substantial dynamic ability at high sound levels. 160 watts to each of the seven main channels the power amp section features an advanced, premium high- storage power supply capacitors, and fully discrete output stages housed in cast aluminum heat sinks . · Current feedback 7ch Amplifier Current feedback topology combines total operation stability with excellent frequency response, while requiring only minimal amounts of negative feedback. It makes excellent transient response and superb sonic transparency. FLEXBILITY FEATURES FUTURE-PROOF INTERFACE ARCHITECTURE a versatile RS232 port allows the SR9200's internal Flash Memory to be directly computer accessed for installing such future upgrades as new DSP algorithms, new surround formats/parameters, and other types of processing updates. MULTIROOM CAPABILITY a full set of line outs for audio, composite video, allows for set-up of an additional system in another room, and complete second-room control can be achieved with such A/V distribution control systems as Xantech ,Niles , to name but a few. Digital I/O Assignable nine Digital inputs, for connection to other sources, such as DVD,DSS, CD or LD. A optical Digital input on front AUX1 terminals, for connection to portable player or game. Two Digital outputs for connection to digital recorder as CD-R or MD. ENGLISH OTHER FEATURES AUDIO/VIDEO FEATURES · THX SURROUND EX built in to decode the additional two surround buck channels from THX Surround EX-encoded DVDs and laserdiscs. · DTS-ES decoder built in to decode the impeccable 6.1-channel discrete digital audio from DTS-ES encoded DVD-Video discs, DVD-Audio discs, CDs and laserdiscs. · DOLBY DIGITAL decoder built in to decode the 5.1-channel digital audio of DVDs, Digital TV, HDTV, satellite broadcasts and other sources. · DOLBY PRO LOGIC II decoder provides better spatiality and directionality on Dolby Surround program material; provides a convincing three-dimensional sound field on conventional stereo music recordings. · HDCD decoding capability to deliver the full sonic benefits of HDCD-encoded CDs from a standard non-HDCD CD player when connected to the SR9200 via the player 's digital output. · CIRCLE SURROUND decoder built in to decode surround sound from any stereo or passive matrix-encoded material. · Multi-channel (7.1ch)direct inputs accommodate future multichannel sound formats or an external digital decoder. · 192kHz/24-bit D/A CONVERTERS for all channels. · ADDC (Advanced Double Differential Converter) output for STEREO playback. · Source Direct mode bypasses, tone controls and bass management for purest audio quality. · Four sets of Y/Cr/Cb component video inputs and component video outputs provide unsurpassed video quality and switching flexibility from component video sources. · Easy to use on-screen menu system in all video monitor output. · High-quality AM/FM tuner with 50 station presets. · 2way programmable learning remote control RC3200A. 2 THX® is an exclusive set of standards and technologies established by the world-renowned film production company, Lucasfilm Ltd. THX resulted from George Lucas' desire to reproduce the movie soundtrack as faithfully as possible both in the movie theater and in the home theater. THX engineers developed patented technologies to accurately translate the sound from a movie theater environment into the home, correcting the tonal and spatial errors that occur. When the THX mode of the SR9200 is on, three distinct THX technologies are automatically added: Re-Equalization-restores the correct tonal balance for watching a movie in a home environment. These sounds are otherwise mixed to be brighter for a large movie theater. Re-EQ compensates for this and prevents the soundtracks from being overly bright and harsh when played in a home theater. Timbre Matching-filters the information going to the surround speakers so they more closely match the tonal characteristics of the sound coming from the front speakers. This ensures seamless panning between the front and surround speakers. Adaptive Decorrelation-slightly changes one surround channel's time and phase relationship with respect to the other surround channel. This expands the listening position and creates with only two surround speakers the same spacious surround experience as in a movie theater with multiple surround speakers. The Marantz SR9200 was required to pass a rigorous series of quality and performance tests, in addition to incorporating the technologies explained above, in order to be THX Ultra certified by Lucasfilm Ltd. THX Ultra requirements cover every aspect of performance including pre-amplifier and power amplifier performance and operation, and hundreds of other parameters in both the digital and analog domain. Movies which have been encoded in Dolby Digital, DTS, Dolby Pro Logic, stereo and Mono will all benefit from the THX mode when being viewed. The THX mode should only be activated when watching movies which were originally produced for a movie theater environment. THX need not be activated for music, movies made especially for TV, or shows such as sports programming, talk shows, etc. This is because they were originally mixed for a small room environment. "Lucasfilm®" and "THX®" are registered trademarks of Lucasfilm Ltd. Lucasfilm and THX are trademarks or registered trademarks of Lucasfilm Ltd. ©Lucasfilm Ltd. & TM. Surround EX is a jointly developed technology of THX and Dolby Laboratories, Inc. and is a trademark of Dolby Laboratories, Inc. All rights reserved. Used under authorization. DTS was introduced in 1994 to provide 5.1 channels of discrete digital audio into home theater systems. DTS brings you premium quality discrete multi-channel digital sound to both movies and music. DTS is a multi-channel sound system designed to create full range digital sound reproduction. The no compromise DTS digital process sets the standard of quality for cinema sound by delivering an exact copy of the studio master recordings to neighborhood and home theaters. Now, every moviegoer can hear the sound exactly as the moviemaker intended. DTS can be enjoyed in the home for either movies or music on of DVD's, LD's, and CD's. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. DTS-ES Extended Surround is a new multi-channel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTSES Extended Surround greatly improves the 360-degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999. In addition to the 5.1 surround channels (FL, FR, C, SL, SR and LFE), DTS-ES Extended Surround also offers the SB (Surround Back) channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal formats with different surround signal recording methods, as DTS-ES Discrete 6.1 and DTSES Matrix 6.1. ] Dolby Digital identifies the use of Dolby Digital (AC-3) audio coding for such consumer formats as DVD and DTV. As with film sound, Dolby Digital can provide up to five full-range channels for left, center, and right screen channels, independent left and right surround channels, and a sixth ( ".1") channel for low-frequency effects. Dolby Surround Pro Logic II is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround program material; provides a convincing three-dimensional soundfield on conventional stereo music recordings; and is ideally suited to bring the surround experience to automotive sound. While conventional surround programming is fully compatible with Dolby Surround Pro Logic II decoders, soundtracks will be able to be encoded specifically to take full advantage of Pro Logic II playback, including separate left and right surround channels. (Such material is also compatible with conventional Pro Logic decoders.) THX Surround EX - Dolby Digital Surround EX is a joint development of Dolby Laboratories and the THX division of Lucasfilm Ltd. In a movie theater, film soundtracks that have been encoded with Dolby Digital Surround EX technology are able to reproduce an extra channel which has been added during the mixing of the program. This channel, called Surround Back, places sounds behind the listener in addition to the currently available front left, front center, front right, surround right, surround left and subwoofer channels. This additional channel provides the opportunity for more detailed imaging behind the listener and brings more depth, spacious ambience and sound localization than ever before. Movies that were created using the Dolby Digital Surround EX technology when released into the home consumer market may exhibit a Dolby Digital Surround EX logo on the packaging. A list of movies created using this technology can be found on the Dolby web site at http ://www.dolby.com. "SURROUND EX TM" is a trademark of Dolby Laboratories. Used under authorization. 3 ENGLISH DESCRIPTION ® ENGLISH HDCD® (High Definition Compatible Digital ®) is a patented process for delivering on Compact Disc the full richness and details of the original microphone feed. HDCD encoded CDs sound better because they are encoded with 20bits of real musical information as compared to 16-bits for all other CDs. HDCD overcomes the limitation of the 16-bit CD format by using a sophisticated system to encode the additional four bits onto the CD while remaining completely compatible with the CD format. When listening to HDCD recordings, you hear more dynamic range, a focused 3-D sound stage, and extremely natural vocal and musical timbre. With HDCD, you get the body, depth and emotion of the original performance not a flat, digital imitation. ® , HDCD®, High Definition Compatible Digital ® and Pacific MicrosonicsTM are either registered trademarks or trademarks of Pacific Microsonics, Inc. in the United States and/or other countries. HDCD system manufactured under license from Pacific Microsonics, Inc. This product is covered by one or more of the following: In the USA: 5,479,168, 5,638,074, 5,640,161, 5,808,574, 5,838,274, 5,854,600, 5,864,311, 5,872,531, and in Australia: 669114. Other patents pending. Circle Surround is backward compatible, such that surround playback is possible from any stereo or passive matrix-encoded material. Five full-bandwidth, discrete channels of information can be extracted from an enormous library of material not multi-channel encoded. These sources include many of today's DVDs and laser discs, as well as most all video tape, VCD, Compact Disc, radio and television broadcast material. Circle Surround and the symbol are trademarks of SRS Labs, Inc. Circle Surround technology is incorporated under license from SRS Labs, Inc. 4 @6 qw e rtyu @7 i o !0 !1 !2 AV SURROUND RECEIVER SR9200 SELECTOR VOLUME DOWN DISPLAY CLEAR MEMO DOWN GYRO TUNING UP F/P AUTO-TUNE T-MODE UP SELECT ENTER LD DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R TUNER MUTE ATT STANDBY MULTI-SPK SLEEP S-DIRECT AUX1 DIGITAL S-VIDEO AUX1 INPUT VIDEO L AUDIO R POWER ON/STANDBY PHONES MULTI ROOM A/D 7.1CH-IN AUX2 R @5 @4 @2 @0 !8 @3 @1 !9 !7 !6 !5 !4 !3 q POWER switch and STANDBY indicator When this switch is pressed once, the unit turns ON and display appears on the display panel. When pressed again, the unit turns OFF and the STANDBY indicator lights. When the STANDBY indicator is turned on, the unit is NOT disconnected from the AC power. u MEMO (memory) button Press this button to enter the tuner preset memory numbers or station names. i GYRO TUNING dial Rotate this dial to change the frequency or the preset number. w SELECT (MULTI FUNCTION MODE SELECT) button Press this button to change the mode for MULTI FUNCTION control dial. o F/P (FREQUENCY / PRESET) button During reception of AM or FM, you can change the function of the GYRO TUNING dial for scanning frequencies or selecting preset stations by pressing these buttons. e SURROUND MODE Selector & MULTI FUNCTION control dial This dial changes surround mode sequentially or select contents of OSD menu system. !0 AUTO TUNING button When this button is pressed and Auto scan function starts when the GYRO TUNING dial is rotated. r ENTER (MULTI FUNCTION ENTER) button Press this button to enter the setup by MULTI FUNCTION dial. !1 FM MODE button Press this button to select the auto stereo mode or mono mode when the FM band is selected. The "AUTO" indicator lights in the auto stereo mode. t DISPLAY mode button When this button is pressed, the FL display mode is changed as NORMAL Auto Off Off and the display off indicator(DISP) lights up in condition of DISPLAY OFF. !2 VOLUME control knob Adjusts the overall sound level. Turning the control clockwise increases the sound level. !3 ATT (Attenuate) button If the selected analog audio input signal is greater than the capable level of internal processing, PEAK indicator will light. If this happens, you should press the ATT button. "ATT" is displayed when this function is activated. The signal-input level is reduced by about the half. Attenuation will not work with the output signal of "REC OUT" (TAPE, CD-R/MD, VCR1 and VCR2 output). This function is memorized for each input function. y CLEAR button Press this button to cancel the station-memory setting mode or preset scan tuning. 5 ENGLISH FRONT PANEL !4 MUTE button Press this button to mute the output to the speakers. Press it again to return to the previous volume level. @5 PHONES jack for stereo headphones This jack may be used to listen to the SR9200's output through a pair of headphones. Be certain that the headphones have a standard 1 / 4" stereo phone plug. Note that the main room speakers will automatically be turned off when the headphone jack is in use. ENGLISH !5 INPUT FUNCTION SELECTOR buttons (AUDIO/ VIDEO) These buttons are used to select the input sources. The video function selector, such as TV, LD, DVD, DSS, VCR1 and VCR2, selects video and audio simultaneously. Audio function sources such as CD, TAPE, CDR/MD, and TUNER may be selected in conjunction with a Video source. This feature (Sound Injection) combines a sound from one source with a picture from another. Choose the video source first, and then choose a different audio source to activate this function. Press TUNER button to switch the between FM or AM. Notes: · When using headphones, the surround mode will automatically change to STEREO. · The surround mode returns to the previous setting as soon as the plug is removed from the jack. @6 INFRARED transmitting sensor window This window transmits infrared signals for the remote control unit. @7 INFRARED receiving sensor window This window receives infrared signals for the remote control unit. !6 AUX1 input jacks These auxiliary video/audio and optical digital input jacks accept the connection of a camcorder, portable DVD, game etc. !7 AUX1 button This button is used to select the AUX1 input source. !8 AUX2 button This button is used to select the AUX2 (L/R input of 7.1 CH. IN). !9 S. (Source) DIRECT button When this button is pressed, the tone control circuitry is bypassed as well as Bass Management. Notes: · The surround mode is automatically switched to AUTO when the source direct function is turned on. · Additionally, Speaker Configurations are fixed automatically as follow. · Front SPKR = Large, Center SPKR = Large, Surround SPKR = Large, Sub woofer = On @0 7.1CH INPUT button Press this button to select the 7.1CH INPUT. @1 SLEEP button Set the sleep timer function with this button. @2 A/D (Analog/Digital) SELECTOR button This is used to select between the analog and digital inputs. Note: · This button is not used for an input source that is not set to a digital input in the system setup menu. @3 M-SPKR (Multi Room Speaker) button Press this button to activate the Multiroom Speaker system . "MSPKR" indicator will light in the display. @4 MULTI (Multi Room) button Press this button to activate the Multiroom system . "MULTI " indicator will light in the display. 6 as DISP ST AUTO PRO LOGIC DIRECT TEST MOVIE d CINEMA MUSIC MUSIC PRO LOGIC DISC 6.1 fgh ANALOG ATT DIGITAL MTX 6.1 SLEEP PEAK j OTHER PCM L k C R TUNED MULTI SLEEP M-SPKR AUTO SURR COPY THX SURR EX NIGHT DIGITAL SURROUND 96kHz LFE SL S SR ¡0 ¡1 ST AUTO l ¡2 DISP PRO LOGIC DIRECT TEST MOVIE ¡3 CINEMA MUSIC MUSIC PRO LOGIC DISC 6.1 ¡4 ATT ¡5 ANALOG DIGITAL OTHER PCM L C R TUNED MULTI SLEEP M-SPKR AUTO SURR COPY THX SURR EX NIGHT MTX 6.1 SLEEP PEAK DIGITAL SURROUND 96kHz LFE SL S SR TM0 ¡9 ¡8 ¡7 ¡6 a DISP (Display Off) indicator This indicator lights when the SR9200 is in the display off condition. k ENCODED CHANNEL STATUS indicators These indicators display the channels that are encoded with a digital input signal. If the selected digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, "L", "C", "R", "LS", "RS" and "LFE" will light up.If the digital input signal is 2 channel PCM-audio, "L" and "R" will be displayed. If Dolby Digital 5.1ch signal with Surround EX flag or DTS-ES signal comes in, "L", "C", "R", "LS", "S" , "RS" and "LFE" will show. s PRO LOGIC II mode indicators (MOVIE, MUSIC, PRO LOGIC) These indicators illuminate when one of the Dolby Pro Logic II modes is in use. d Circle Surround mode indicators (CINEMA, MUSIC) These indicators illuminate when one of the Circle Surround modes is in use. l Main Information Display This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of unit's operation. f ATT (Attenuation) indicator This indicator lights when the attenuation function is active. ¡0 Multi-room system indicator MULTI : This indicator lights when the multi-room system is active. SLEEP : This indicator lights when the sleep timer to multi-room system is active. M-SPKR : This indicator lights when the Multi-room Speaker output is active. g DIGITAL Input Indicator This indicator lights when digital input has been selected. h ANALOG input indicator This indicator lights when an analog input source has been selected. ¡1 TUNER's indicators ST(Stereo) : This indicator illuminates when an FM station is being tuned in stereo condition. AUTO : This indicator illuminates when the tuner's Auto mode is in use. TUNED : This indicator illuminates when a station is being received with sufficient signal strength to provide acceptable listening quality. j SIGNAL FORMAT indicators 2 DIGITAL, 2 SURROUND, dts, ES, PCM, 96kHz, HDCD, and OTHER When the selected input is a digital source, some of these indicators will light to display the specific type of signal in use. 7 ENGLISH FL DISPLAY ¡2 AUTO.SURR (Auto Surround mode) indicator. This indicator illuminates to show that the AUTO SURROUND mode is in use. ENGLISH ¡3 THX SURR EX (THX Surround EX mode) indicator. When THX surround EX mode is selected , this indicator lights. ¡4 DTS-ES mode indicators (DISC6.1, MTX6.1) These indicators will show to DTS-ES decoding mode. ¡5 PEAK indicator This indicator is a monitor for an analog audio input signal. If the selected analog audio input signal is greater than the capable level of internal processing, this will light. If this happens, you should press the ATT button. ¡6 SLEEP timer indicator This indicator lights when the seep timer function in main-room is in use. ¡7 NIGHT mode indicator This indicator lights when the SR9200 is in the Night mode, which reduces the dynamic range of digital program material at low volume levels. ¡8 COPY indicator This indicator lights when DIGITAL COPY system is active. ¡9 TEST tone indicator This indicator blinks in generating the test tone in speaker level setup. TM0 DIRECT (Soruce direct) indicator This indicator lights when the SR9200 is in the SOURCE DIRECT mode. 8 z x cv bn m , . /0 DIGITAL-OUT OPT 1 L ­ PRE OUT MAIN IN GND MULTI VIDEO OUT MONI. 1 MONI. 2 MODEL NO.SR9200 FRONT LEFT + ­ MULTI ROOM LEFT + Y FRONT MULTI ROOM RIGHT ANTENNA 2 R GND LD COAX 3 C AM CB MONITOR OUT RIGHT DVD CR SURR. BACK LEFT CENTER RS232C 4 SW DSS Y DSS IN SURR. VCR2/ DVD-R IN BACK RIGHT SURR. LEFT R 5 SL EXT. IR OUT FRONT L CD TV CB 6 DC OUT 1 DC OUT 2 SR SURR. IN TAPE IN VCR1 OUT CR SURR. RIGHT 7 SBL IN MULTI RC OUT SURR. BACK OUT Y DVD IN SWITCHED 120W 1A VCR1 IN UNSWITCHED 120W 1A SPEAKER SYSTEMS 6-8 OHMS 8 SBR S.W IN CD-R CENTER /MD OUT IN VCR2/ DVD-R OUT CB RC-5 9 MULTI OUT CR S-VIDEO COMPONENT VIDEO AC OUTLETS 120V 60HZ AC IN DIGITAL-IN R L 7.1CH-IN R AUDIO L R L VIDEO ¤0 /9 /8 /7 /6 /5 /4 /3 /2 /1 z DIGITAL INPUT (Dig.1 - 9) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 5 digital inputs with coaxial jacks, 4 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components. b FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best x Preamp Outputs (L, R, SL, SR, SBL, SBR, C) When the jumper plugs that link the Amplifier Inputs with these outputs are removed, these jacks may be connected to an external power amplifier. n Multiroom Outputs (Audio L&R, Video) These are the audio and video output jacks for the remote zone (Multi Room). Connect these jacks to the optional audio power amplifiers or video display devices to view and listen to the source selected by the mulitroom system in a remote room. c Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. m MONITOR OUT There are 2 monitor outputs and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT. v Main Amplifier Inputs When the jumper plugs that link the Preamp Outputs with these inputs are removed, these jacks may be used to connect an external source to the internal amplifiers. Notes: · When connecting a equipment, remove the attached jumper plugs and store them carefully so as not to lose them. · Only remove the jumper plugs when required. After you finish using an Main Amp Input jack, replace the jumper plug. 9 ENGLISH REAR PANEL , COMPONENT VIDEO INPUT/OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR9200. The SR9200 has four component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly lifelike colors and crisp detail. /4 AUDIO IN/OUT (CD, TAPE, CD-R, TV, DVD, DSS, LD, VCR1, VCR2) These are the analog audio inputs and outputs. There are 9 audio inputs (6 of which are linked to video inputs) and 4 audio outputs (2 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players,DVD players and etc.... The audio inputs and outputs require RCA-type connectors. ENGLISH /5 7.1 CHANNEL INPUT By connecting a DVD Audio player, SACD player, or other component that has a multi channel port, you can playback the audio with 5.1 channel or 7.1 channel output. Notes: · This component video output is available to OSD menu system. . Speaker outputs terminals (for Main room) Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left, and surround back right speakers. /6 RS232C The RS232C port is to be used in conjunction with an external controller to control the operation of the SR9200 by using an external device. The RS232C port may also be used in the future to update the operating software of the SR9200 so that it will be able to support new digital audio formats and the like as they are introduced. /0 Speaker outputs terminals (for Multi room) Two terminals are provided for the left and right speakers for Multiroom(2nd zone) /7 REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC5) terminals. Notes: · Connect the these jacks to the matching + or ­ terminals on your speakers. When making speaker connections, always make certain to maintain correct polarity by connecting the red (+) terminals on the SR9200 to the red terminals on the speaker and the black (­) terminals on the SR9200 to the black terminals on the speakers. /8 MULTI ROOM REMOTE IN/OUT terminals IN: Connect to multi-room remote control device, available from your Marantz dealer. OUT: Connect to the Marantz component equipped with remote control (RC-5) terminals in another room (Second zone). /1 AC INLET Plug the supplied power cord into this AC INLET and then into the power outlet on the wall. /9 DC TRIGGER output terminals Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc...) Use the system OSD setup menu to determine the conditions by which these jacks will be active. /2 AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power only when the SR9200 is turned on and is useful for components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the SR9200 is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with its own power switch. Note: · This output voltage is for (status) control only, It is not sufficient for drive capability. ¤0 External IR transmitter terminal If the SR9200 is located inside a rack or cabinet that will not allow infrared beams to transmit to 2way remote commander, you will need to connect a IR transmitter to this output to be able to use the 2way remote controller. Then install the remote transmitter in an unblocked location where you can easily receive IR signal. Caution: · In order to avoid potential turn-off thumps, anything plugged in here should be powered up before the SR9200 is turned on. Note: · An optional remote transmitter kit is required. /3 VIDEO IN/OUT (TV, DVD, DSS, LD, VCR1, VCR2) These are the video inputs and outputs. There are 6 video inputs and 2 video outputs and each one includes both composite video and Svideo configurations. Connect VCRs, LD players, DVD players, and other video components to the video inputs. S-video sources can be viewed through the S-video outputs, and composite sources can only be viewed through the composite output. The 2 video output channels can be used to be connected to video tape recorders for making recordings. 10 Press this button turns on the backlight to LCD display. This chapter describes the functions which control the SR9200. Please look at the user guide of the RC3200A for operation instructions. K Serial port To connect the RC3200A with your computer by attached serial cable for future upgrades. 12 11 10 9 ^ L LCD touch scren The LCD touch screen is divided into different sections: Here the date and time are displayed when you are operating your devices. In this area you can see: · the page number; · the device you are operating; · the battery level indicator. With these soft buttons you operate your device. 1 8 7 6 5 VOL Navigation bar: These are the labels of the 4 hard buttons below the touch screen. OK CH 2 3 4 H S Ex M LOADING BATTERIES When you use RC3200A for the first time, you have to install the batteries. The RC3200A requires 3 AA-batteries (3 x 1,5 V) to function. Note · Attached batteries are to check basic function of remote commander, you can use either primary or rechargeable batteries. A Select buttons to Navigation bar These buttons work with navigation bar in LCD. Each function may also be provided with an alphanumeric function indicator visible in navigation bar of LCD display. 1. Remove the back cover. B CH (Channel) UP and DOWN buttons Use these buttons to select the preset number of tuner in the SR9200 or channel of TV. C S (Status) button Press this button to see (jump to) the status of SR9200 on LCD panel. 2. Insert the new batteries (AA type) with correct (+) and (­) polarity. D M (Menu) button Use this button to entry the OSD menu system. E Ex (Exit ) button