MAC 250 Krypton/Entour user manual All measurements are expressed in millimeters 469 364 538 119 315 375 393 270° 270° 128.5° 128.5° 560 © 2004-2005 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark. P/N 35000126 Rev. H CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 MAC 250 Krypton/Entour safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the serial data link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 8 9 CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DMX Mode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DMX Address selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tailoring performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information readouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Test and service utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 11 11 12 13 DMX-512 CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Lamp power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Effect position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Speed control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 OPTICAL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Rotating gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixed gobos (MAC 250 Entour only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Color filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting the optional 14° lens (MAC 250 Entour only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 20 22 23 26 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Lamp replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Updating software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 30 31 31 32 DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 MAC 250 Krypton DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 MAC 250 Entour DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 CONTROL MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ERROR MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 CIRCUIT BOARD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 SPECIFICATIONS - MAC 250 KRYPTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 SPECIFICATIONS - MAC 250 ENTOUR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 This page left intentionally empty. 4 MAC 250 Krypton/Entour INTRODUCTION Thank you for selecting the Martin MAC 250 Krypton or the MAC 250 Entour. Features Some of the many features include: · · · · · · · · · · efficient, 3000 hour, 250 watt discharge lamp 12 interchangeable dichroic colors 7 interchangeable indexed-rotation gobos interchangeable 3-facet rotating prism motorized focus full-range dimming fast blackout and strobe effects coated optics user-installable firmware switch-selectable power supply settings The MAC 250 Entour additionally features: · 10 fixed gobos · Tilt locks · Optional lens providing a 14° beam angle For the latest firmware updates, documentation, and other information about this and all Martin Professional products, please visit the Martin web site at http://www.martin.com. Please check the Martin web site at http://www.martin.dk for the latest product software and documentation. Comments or suggestions regarding this document may be e-mailed to service@martin.dk or posted to Martin Professional A/S Olof Palmes Allé 18 DK-8200 Aarhus N, Denmark Attn: Service Department Please review the important safety precautions in this manual before installing and operating the fixture. MAC 250 Krypton/Entour safety information Warning! This product is for professional use only. It is not for household or residential use. This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation, lamp explosion, and falls. Read this manual before powering or installing the fixture, follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture. If you have questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin 24-hour service hot line at +45 70 200 201. PROTECTION FROM ELECTRIC SHOCK Warning! Always disconnect from mains supply before replacing the lamp. · Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when not in use. · Always ground (earth) the fixture electrically. · Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault protection. Introduction 5 · Do not expose the fixture to rain or moisture. · Refer any service operation not described in this manual to a qualified technician. PROTECTION FROM UV RADIATION AND LAMP EXPLOSION · Never operate the fixture with missing or damaged lenses and/or covers. · When replacing the lamp, allow the fixture to cool for at least 15 minutes before opening the fixture or removing the lamp. Protect your hands and eyes with gloves and safety glasses. · Do not stare directly into the light. Never look at an exposed lamp while it is lit. · Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life. PROTECTION FROM BURNS AND FIRE Danger! Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get very hot - up to 120° C (248° F). Allow the fixture to cool for at least 45 minutes before handling. Prolonged exposure to unshielded lamp can cause eye and skin burns. · Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the specified type and rating. · Keep all combustible materials (for example fabric, wood, paper) at least 1 meter (39 inches) away from the fixture. Keep flammable materials well away from the fixture. · Do not illuminate surfaces within 3 meters (10 feet) of the fixture. · Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents. · Never place filters or other materials over the lens. · Do not modify the fixture or install other than genuine Martin parts. · Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F). Protection from injury due to falls · Do not lift or carry the fixture alone. · When suspending the fixture, verify that the structure can hold at least 10 times the weight of all installed devices. · Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable. · Block access below the work area whenever installing or removing the fixture. 6 MAC 250 Krypton/Entour SETUP Unpacking The MAC 250 Krypton/Entour comes with: · · · · · MSD 250/2 lamp (factory installed) 3-meter, 3-wire IEC power cable user manual 1/4-turn clamp mounting bracket 5-meter, 3-pin shielded XLR control cable The MAC 250 Entour also comes with an extra 14° lens. The packing material or flightcase is carefully designed to protect the fixture during shipment - always use it to transport the fixture. When installing the MAC 250 Entour model you may find it useful to lock the head in place using the tilt locks. AC power Warning! For protection from electric shock, the fixture must be grounded (earthed). The power supply shall have overload and ground-fault protection. Important! Verify that power supply settings match the local AC supply before use. The MAC 250 Krypton/Entour is factory configured for 230 V / 50 Hz operation. If your AC power supply is different, the fixture must be configured for the local voltage and frequency. Always use the settings that are closest to your AC supply. CONFIGURING FOR LOCAL AC POWER Frequency Voltage 50 60 250 230 210 100 120 Figure 1: Power supply settings 1. Disconnect the fixture from power. Setup 7 2. Remove the 2 Phillips screws in the access cover directly behind the power and data connectors. Lift off the cover. 3. Locate the selection switches. 4. Move the voltage switch to the setting that most closely matches the local AC voltage. If your voltage falls halfway between 2 settings, select the higher voltage. For example, if the AC voltage is 220 V, use the 230 V setting instead of 210 V. 5. Move the frequency switch to the setting that matches the local AC frequency: 50 or 60 Hz. 6. Replace the cover. INSTALLING A PLUG ON THE POWER CABLE The power cable must be fitted with a grounding-type cord cap that fits your power distribution system. Consult an electrician if you have any doubts about proper installation. · Following the cord cap manufacturer's instructions, connect the yellow and green wire to ground (earth), the brown wire to live, and the blue wire to neutral. The table below shows some pin identification schemes. Wire brown blue yellow/green Pin live neutral ground Marking "L" "N" Screw color yellow or brass silver green Table 1: Plug wiring APPLYING POWER Warning! The power cables must be undamaged and rated for the electrical requirements of all connected devices. Important! Powering through a dimmer system can damage the fixture. 1. Verify that the supply cable is undamaged and rated for the current requirements of all connected devices. 2. Plug the prepared power cable into the AC socket and a grounded AC power supply. Installation LOCATION AND ORIENTATION ...