User manual MATSONIC MS6391E

Mainboard User's Manual This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademarks IBM, VGA, and PS/2 are registered trademarks of International Business Machines. Intel, Pentium, Pentium-III, MMX, and Celeron are registered trademarks of Intel Corporation. Microsoft, MS-DOS and Windows 95/98/NT are registered trademarks of Microsoft Corporation. Sound Blaster is a trademark of Creative Technology Ltd. PC-cillin and ChipAwayVirus are trademarks of Trend Micro Inc. AMI is a trademark of American Megatrends Inc. A3D is a registered trademark of Aureal Inc. Gamut is a registered trademark of Formosoft International Inc. SuperVoice is a registered trademark of Pacific Image Communications Inc. MediaRing Talk is a registered trademark of MediaRing Inc. Other names used in this publication may be trademarks and are acknowledged. Copyright © 2000 All Rights Reserved MS6391E, V1.3 S54T/JUNE 2000 MS6391E Mainboard User's Manual Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: q Reorient or relocate the receiving antenna. q Increase the separation between the equipment and the receiver. q Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected. q Consult the dealer or an experienced radio/TV technician for help. Shielded interconnect cables and shielded AC power cable must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system's manufacturer could void the user's authority to operate the equipment. Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: q This device may not cause harmful interference, and q This device must accept any interference received, including interference that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada. II MS6391E Mainboard User's Manual Table of Contents Chapter 1: Introduction ..............................................................1 Key Features......................................................................2 Package Contents ...............................................................5 Static Electricity Precautions ...............................................6 Pre-Installation Inspection...................................................6 Chapter 2: Mainboard Installation ...............................................7 Mainboard Components......................................................8 Install A CPU ....................................................................9 Install Memory................................................................. 10 Setting Jumper Switches ................................................... 11 Install the Mainboard........................................................ 13 Install the Extension Brackets ........................................... 14 Install Other Devices........................................................ 20 Expansion Slots................................................................ 21 Chapter 3: BIOS Setup Utility .................................................. 23 Introduction ..................................................................... 23 Running the Setup Utility.................................................. 24 Standard CMOS Setup Page ............................................. 25 Advanced Setup Page ....................................................... 26 Power Management Setup Page ........................................ 28 PCI / Plug and Play Setup Page ......................................... 30 Load Optimal Settings ...................................................... 31 Load Best Performance Settings ........................................ 31 Features Setup Page ......................................................... 31 CPU PnP Setup Page ........................................................ 33 Hardware Monitor Page.................................................... 34 Change Password............................................................. 34 Exit.................................................................................. 35 Chapter 4 Software & Applications ........................................... 36 Introduction ..................................................................... 36 Using the PCI Sound Pro Application ................................ 36 The Four Speakers System................................................ 37 Speaker Installation .......................................................... 37 Speaker Position............................................................... 37 Mixer Setup ..................................................................... 38 Demo .............................................................................. 38 III MS6391E Mainboard User's Manual Appendix A: Gamut .............................................................A1 Introduction ....................................................................A2 Before Installation ..........................................................A3 Installation .....................................................................A4 Produce MP3 file Use CD-Cashier ................................A5 Play MP3 filesUse Musician ........................................A7 Play music CDUse 3DFS-ACD .....................................A8 Play MIDI filesUse Midier ..........................................A9 Recording audio dataUse Voice-Catcher .................... A10 IV 1: Introduction Chapter 1 Introduction This mainboard supports all Socket 7 processors including newer designs which feature a 100 MHz system bus . The mainboard firmware supports CPU Plug and Play so that the system will automatically adopt the correct configuration for the Socket-7 processor that you install. This mainboard uses the SiS540 chipset which integrates a 3D AGP Graphics Accelerator and has an embedded 10BaseT/100BaseTX Ethernet Network Interface.The mainboard has a built-in PCI 3D Sound System and a V.90 Fax/Modem DAA module is shipped with the mainboard. There is an ADIMM slot onboard for either an optional Video Bridge Card or a display buffer cache card. The video bridge card connects to an external TV, a TFT LCD panel display, or a secondary CRT display monitor. In addition, the mainboard has a full set of I/O Ports and two expansion slots. This mainboard has all the features you need to develop a powerful multimedia workstation that is network ready, and has built-in communications. The board is Baby-AT form factor and supports both AT/ATX power supply. If you use an ATX supply, it supports all of the ATX power management features including ACPI (Advanced Configuration and Power management Interface), power saving modes and keyboard power on hot keys feature. 1 MS6391E Mainboard User's Manual Key Features The key features of this mainboard include: Socket-7 Processor Support Supports all recent socket-7 processors including the Intel P55C (Pentium MMX), the Cyrix/IBM 6x86L/6x86MX /MII, the AMD K6/K6-2/K6-III, IDT C6, and WinChip 2/2A CPUs Supports socket-7 processors with system bus frequencies of 66/100 MHz CPU Plug and Play support lets the firmware automatically configure the CPU Memory Support Two DIMM slots for 168-pin SDRAM memory modules Support for 66MHz, 100MHz memory bus Maximum installed memory is 2 x 512MB = 1 GB Expansion Slots Two 32-bit PCI slots One ADIMM slot for optional display cache card or video bridge card Onboard IDE channels Primary and Secondary PCI IDE channels Support for PIO (programmable input/output) modes Support for Multiword DMA modes Support for Bus Mastering and Ultra DMA 33/66 modes Power Supply and Power Management Provides AT/ATX power connector ACPI and previous PMU support, suspend switch, keyboard power on/off Supports Wake on Modem, Wake on LAN and Wake on Alarm 2 1: Introduction Built-in Graphics System Onboard 128-bit 2D/3D 100MHz Host interface AGP Graphics Accelerator Complies with AGP V2.0 Shared memory architecture allows a maximum of 64 MB main memory to act as frame buffer Supports high resolutions up to 1920x1200 16M colors, up to 2048x2048 Texture size and Virtual screen up to 4096x4096 Supports hardware DVD Accelerator Sound System Complies with the PC98 audio specification 16-bit CODEC for full-duplex playback and recording HRTF 3D professional audio supports both Direct Sound 3D ® and A3D ® -compatible interfaces plus support for 4channel speakers Driver support for MS-DOS, Microsoft Windows 95/98/2000/NT 4.0 Built-in 32ohm earphone buffer and 3D surround sound Provides MPU-401 Game/MIDI port and legacy Sound Blaster 16 support Downloadable Wave-table Synthesizer supports Direct Music® Stereo Mixer supports analog mixing from CD-Audio and Line In or digital mixing from voice, FM/Wave-table and digital CD-Audio 3 MS6391E Mainboard User's Manual Onboard I/O Ports Provides PC99 Color Connectors for easy peripheral device connections Floppy disk drive connector with 1Mb/s transfer rate One serial port with 16550-compatible fast UART One parallel port with ECP and EPP support Optional ATX Form card provides two USB ports, a PS/2 port for mouse and a infrared port Built-in Ethernet LAN 10BaseT/100BaseTX Ethernet LAN LAN controller integrates Fast Ethernet MAC and PHY compliant with IEEE802.3u 100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD standards Compliant with ACPI 1.0 and the Network Device Class Power Management 1.0 High Performance provided by 100Mbps clock generator and data recovery circuit for 100Mbps receiver Fax/Modem DAA Module 56 Kbps Fax/Modem DAA module Supports V.90, V.34, V.32bis, V.32, V.22bis, V.22 Supports Auto Fallback and MNP 5, V.42bis data compression with 115,200-compatible Virtual UART Requires 16MB RAM and Microsoft Windows 95/98/NT Onboard Flash ROM Automatic CPU and board configuration Supports Plug and Play configuration of peripheral devices and expansion cards Built-in virus protection using Trend's ChipAwayVirus provides boot process virus protection. 4 1: Introduction Bundled Software PC-Cillin provides automatic virus protection under Windows 95/98 SuperVoice is data, fax and voice communication software Gamut provides professional audio features included MP3 encoding/playback MediaRing Talk provides PC to PC or PC to Phone internet phone communication S-YXG50 is music synthesizer software to playback MIDI files on the system Dimensions Baby-AT form factor (22cm x 22cm) Package Contents Your mainboard package ships with the following items: q q q q q q q q The mainboard This User's Guide 1 UDMA/66 IDE cable 1 Floppy disk drive cable Audio ports and Game/MIDI port extension bracket Serial/parallel ports extension bracket VGA extension bracket Support software on CD-ROM disc 5 MS6391E Mainboard User's Manual Optional Accessories You can purchase the following optional accessories for this mainboard. q q q q q Fax/Modem DAA module ATX Form card (2 USB ports, IR port & PS/2 mouse Port) 10BaseT/100BaseTX network adapter extension bracket SiS301 video bridge card 8/32 MB display cache card Static Electricity Precautions Components on this mainboard can be damaged by static electricity. Take the following precautions when unpacking the mainboard and installing it in a system. 1. Keep the mainboard and other components in their original static-proof packaging until you are ready to install them. 2. During installation, wear a grounded wrist strap if possible. If you don't have a wrist strap, discharge static electricity by touching the bare metal of the system chassis. 3. Handle the mainboard carefully by the edges. Avoid touching the components unless it is absolutely necessary. During installation put the mainboard on top of the static-protection packaging it came in with the component side facing up. Pre-Installation Inspection 1. Inspect the mainboard for damage to the components and connectors on the board. 2. If you suspect that the mainboard has been damaged, do not connect power to the system. Contact your mainboard vendor and report the damage. 6 2: Mainboard Installation Chapter 2 Mainboard Installation To install this mainboard in a system, follow the procedures in this chapter: q q q q q q q Identify the mainboard components Install a CPU Install one or more system memory modules Verify that any jumpers or switches are set correctly Install the mainboard in a system chassis (case) Connect any extension brackets or cables to the mainboard connector headers Install any other devices and make the appropriate connections to the mainboard connector headers. Note: 1. Before installing this mainboard, make sure jumper JP6 is set to Normal, the default setting is set to Clear CMOS. See this chapter for information on locating JP6 and the setting options. 2. Never connect power to the system during installation. Doing so may damage the mainboard. 7 MS6391E Mainboard User's Manual Mainboard Components Use the diagram below to identify the major components on the mainboard. Note: Any jumpers on your mainboard that do not appear in this illustration are for testing only. 8 2: Mainboard Installation Install A CPU This mainboard has a Socket-7 which may be installed with any of the socket-7 processors including the Intel P55C (MMX) series, the Cyrix/IBM 6x86L/6x86MX/MII series, the AMD K6/K6-2/K-III series, the IDT C6/Winchip 2/2A series. The mainboard supports system bus speeds of 66, 100 MHz. Do not try to install a Socket-370 processor in the Socket-7. A Socket-370 processor such as the PPGA Celeron or FCPGA Pentium III does not fit in the Socket-7. The board supports CPU plug and play, so the system can automatically run the installed processor with the correct clock speed and the correct system bus frequency. To automatically configure the processor, use the BIOS setup program to select the clock speed and system bus frequency. See chapter three for more information. To ensure reliability, make sure that your socket-7 processor is fitted with a heatsink/cooling fan assembly. The socket-7 processor installs into the ZIF (Zero Insertion Force) socket-7 on the mainboard. 1. Locate the Socket-7 and CPUFAN. Pull the locking lever out slightly from the socket and raise it to the upright position. Pin-1 Corner Socket-7 CPUFAN 9 MS6391E Mainboard User's Manual 2. On the processor, identify the Pin-1 corner by its beveled edge. 3. On the Socket-7, identify the Pin-1 corner. The Pin-1 corner is at the end of the locking lever when it is locked. 4. Match the Pin-1 corners and insert the processor into the socket. No force is required and the processor should drop into place freely. 5. Swing the locking lever down and hook it under the catch on the side of the socket. This secures the CPU in the socket. 6. All processors should be installed with a combination heatsink/cooling fan, connect the cable from the fan to the CPU fan power connector CPUFAN. Install Memory The mainboard has two DIMM sockets for system memory modules. You must install at least one memory module in order to use the mainboard. DIMM1 DIMM2 For this mainboard, you must use 168-pin, 3.3V unbuffered SDRAM memory modules. If the installed CPU uses a 100 MHz system bus, you must use PC100 memory. If the installed CPU uses a 66 MHz system bus, you must use PC66 memory. You can install any size memory module from 16 MB to 512MB, so the maximum memory size is 2 x 512MB = 1GB. The edge connectors on the memory modules have cut outs, which coincide with spacers in the DIMM sockets so that memory modules can only be installed in the correct orientation. 10 2: Mainboard Installation To install a module, push the retaining latches at either end of the socket outwards. Position the memory module correctly and insert it into the DIMM socket. Press the module down into the socket so that the retaining latches rotate up and secure the module in place by fitting into notches on the edge of the module. Setting Jumper Switches Jumpers are sets of pins which can be connected together with jumper caps. The jumper caps change the way the mainboard operates by changing the electronic circuits on the mainboard. If a jumper cap connects two pins, we say the pins are SHORT. If a jumper cap is removed from two pins, the pins are OPEN. JP6 1 1 JP2 JP3 1 1 JP1 Jumper JP1: Keyboard Power On Selector If you enable the keyboard power on feature, you can use hot keys on your keyboard as a power on/off switch for the system. Note: The system must provide 1A on the +5VSB (+5V Standby) signal before using the Keyboard Power On function. Function Disable Keyboard Power On Enable Keyboard Power On Jumper Setting Short Pins 1-2 Short Pins 2-3 11 MS6391E Mainboard User's Manual Jumper JP2: Fax/Modem Enable/disable Use this jumper to enable or disable the onboard Fax/Modem. Disable the Fax/Modem if you plan on using another Fax/Modem. Function Enable Fax/Modem Disable Fax/Modem Jumper Setting Short Pins 1-2 Short Pins 2-3 Note: If you have disabled the onboard audio system with jumper JP3, the Fax/Modem will not function even if it is enabled. Jumper JP3: Audio System Enable/disable Use this jumper to enable or disable the audio system integrated on this mainboard. Disable the built-in audio if you plan on using another audio system on an expansion card. Function Enable Audio Disable Audio Jumper Setting Short Pins 1-2 Short Pins 2-3 Note: If you disable the onboard audio system, you cannot use the onboard Fax/Modem. Jumper JP6: Clear CMOS Memory Use this jumper to clear the contents of the CMOS memory. You may need to clear the CMOS memory if the settings in the Setup Utility are incorrect and prevent your mainboard from operating. To clear the CMOS memory, disconnect all the power cables from the mainboard and then move the jumper cap into the CLEAR setting for a few seconds. Function Normal Operation Clear CMOS Memory Jumper Setting Short Pins 1-2 Short Pins 2-3 12 2: Mainboard Installation Install the Mainboard Install the mainboard in a system chassis (case). The board is a baby-AT size mainboard. However, the board supports an AT and an ATX power supply so you can use either an AT or ATX system case. If you use an AT case, some of the ATX power management features might not function. Install the mainboard in a case. Follow the instructions provided by the case manufacturer using the hardware and internal mounting points on the chassis. J1: AT J10 PWR1: ATX SYSTEMFAN If you are using a case with an ATX power supply , connect the power cable from the ATX power supply unit to the power connector PWR1 on the mainboard. If you are using a case with an AT power supply , connect the power cable from the AT power supply unit to the power connector J1 on the mainboard. If there is a cooling fan installed in the system chassis, connect the cable from the cooling fan to the SYSTEMFAN fan power connector on the mainboard. Connect the case switches and indicator LEDs to the J10 switch and LED connector header. 13 MS6391E Mainboard User's Manual See the illustration below for a guide to the J10 connector pin assignments. 12 Speaker Pins 1-3-5-7 Power LED Pins 2-4-6 HDD LED Pins 15-16 Reset Switch Pins 17-18 Suspend LED Pins 19-20 Power/Suspend Switch Pins 21-22 21 22 Install the Extension Brackets The extension brackets are used to connect features on the mainboard to external connectors that can be attached to the system chassis. Follow the steps below to install the extension brackets. Note: All the ribbon cables used on the extension brackets have a red stripe on the Pin-1 side of the cable. VGA Extension Bracket The VGA extension bracket has a 15-pin connector for an external monitor cable. 1 VGA Header VGA Extension Bracket 14 2: Mainboard Installation 1. On the mainboard, locate the VGA header for this bracket. 2. Plug the cable from the bracket into the VGA header. 3. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. Fax/Modem Module The Fax/Modem DAA module plugs directly into the mainboard in line with to an expansion slot opening in the system chassis. When you remove the slot cover from the system chassis, you can access the LINE and TEL RJ11 connectors on the metal edge of the Fax/Modem DAA module. DAA1-Modem Header 1 1. Locate the Modem header on the mainboard. 2. Plug the Fax/Modem DAA module into the Modem header. 3. Remove the modem header slot cover. Line & Tel RJ11 Sockets Modem DAA Module Modem Header 15 MS6391E Mainboard User's Manual Audio Ports and Game/MIDI Port Extension Bracket This bracket provides three audio jacks for stereo line in, stereo line out and microphone. In addition it has a 15-pin D-connector which can be used by either a joystick or a MIDI device. If you are using a four channel speaker system, channel one and two are output through the Stereo Line-out, and the rear speaker channels three and four are output through Stereo Line-in. 1 J4-Sound Header Stereo Line-in /Rear speaker channels 3-4 Microphone Stereo Line-out /Speaker channels 1-2 Game/MIDI Audio Ports & Game/MIDI Extension Bracket 1. On the mainboard, locate the J4-Sound header for this bracket. 2. Plug the cable from the bracket into the header. 3. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. 16 2: Mainboard Installation Serial/Parallel Ports Extension Bracket This bracket has one serial port - COM1 (9-pins) and one parallel port ­ LPT1 (25pins). 1 COM1 Header 1 PRN1 Serial Port COM1 Parallel Port LPT1 Serial/Parallel Ports Extension Bracket 1. On the mainboard, locate the headers COM1 and PRN1 for this bracket. 2. Plug the serial cable into COM1 and the parallel cable into PRN1. 3. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. 17 MS6391E Mainboard User's Manual LAN Network Adapter Extension Bracket This bracket supports an RJ45 network connector and connects to the built in LAN header LAN1 on the mainboard. 1 LAN Header LAN Extension Bracket 1. On the mainboard, locate the LAN header for this bracket. 2. Plug the cable from the bracket into the LAN header. 3. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. 18 2: Mainboard Installation ATX Form Card This ATX Form card provides a mini-DIN port for infrared, one mini-DIN port for a PS/2 mouse. In addition it has two USB (Universal Serial Bus) ports. 1 ATX Header Infrared Port PS/2 Mouse Port USB Ports ATX Form Card 1. On the mainboard, locate the ATX header for this bracket. 2. Plug the cable from the bracket into the ATX header. 3. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. 19 MS6391E Mainboard User's Manual Install Other Devices Install and connect any other devices in the system following the steps below. 1 IDE2 11 IDE1 FDD1 Floppy Disk Drive The mainboard ships with a floppy disk drive cable that can support one or two drives. Drives can be 3.5" or 5.25" wide, with capacities of 360K, 720K, 1.2MB, 1.44MB, or 2.88MB. Install your drives and connect power from the system power supply. Use the cable provided to connect the drives to the floppy disk drive header FDD1. IDE Devices IDE devices include hard disk drives, high-density diskette drives, and CD-ROM or DVD-ROM drives, among others. The mainboard ships with an IDE cable that can support one or two IDE devices. If you connect two devices to a single cable, you must configure one of the drives as Master and one of the drives as Slave. The documentation of the IDE device will tell you how to configure the device as a Master or Slave device. The Master device connects to the end of the cable. Install the device(s) and connect power from the system power supply. Use the cable provided to connect the device(s) to the Primary IDE channel connector IDE1 on the mainboard. If you want to install more IDE devices, you can purchase a second IDE cable and connect one or two devices to the Secondary IDE channel connector IDE2 on the mainboard. If you have two devices on the cable, one must be Master and one must be Slave. 20 2: Mainboard Installation Internal Sound Connections If you have installed a CD-ROM drive or DVD-ROM drive, you can connect the drive audio cable to the onboard sound system. On the mainboard, locate the two 4-pin connectors CD1 and CD2. There are two kinds of connector because different brands of CDROM drive have different kinds of audio cable connectors. Connect the cable to the appropriate connector. 1 CD1 CD2 Expansion Slots This mainboard has two 32-bit PCI expansion slots and one optional ADIMM slot. The PCI slot PCI2 is shared with the USB port. It means that you can use either one of shared both but you cannot use the both at the same time. PCI2 PCI1 ADIMM1 Follow the steps below to install a PCI or ADIMM expansion card. 21 MS6391E Mainboard User's Manual 1. Select a free PCI or ADIMM slot on the mainboard. 2. Remove the slot cover for the expansion slot from the system chassis. 3. Insert the expansion card edge connector into the slot and press it firmly down into it so that it is fully inserted. 4. Secure the expansion card bracket to the system chassis using the screw that held the slot cover in place. ADIMM slot ADIMM stands for Advanced Double In-line Memory Module. Use this slot to install a display cache card or video bridge card. You can purchase an optional SiS301 video bridge card which supports an NTSC/PAL video encoder with a Macrovision V7.1.L1 option for TV display, a TMDS® transmitter with bi-linear scaling capability for a TFT LCD panel display, or an analog RGB port to support a secondary CRT monitor display. These functions support dual-display features. The second display can display independent resolutions, color depths and frame rates different from the primary VGA display. The card receives digital video signals and control signals from the VGA circuitry and transforms them into composite or component video output for a TV display, TMDS® signals for an LCD display or analog RGB signals for a secondary CRT display. 22 MS6391E Mainboard User's Manual Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information about your computer such as the date and time, the kind of hardware installed, and various configuration settings. Your computer uses this information to initialize all the components when booting up and functions as the basis for coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. It can even stop your computer from booting properly. If this happens, you can use the clear CMOS jumper to clear the CMOS memory used to store the configuration information, or you can hold down the Page Up key while you reboot your computer. Holding down the Page Up key also clears the CPU PnP Setup information, you may need to set the CPU speed again. You can run the setup utility and manually make changes to the configuration. You might need to do this to configure some of the hardware that you install on or connect to the mainboard, such as the CPU, system memory, disk drives, etc. 23 MS6391E Mainboard User's Manual Running the Setup Utility Each time your computer starts, before the operating system loads, a message appears on the screen that prompts you to "Hit if you want to run SETUP". When you see this message, press the Delete key and the Main menu page of the Setup Utility appears on your monitor. AMIBIOS SIMPLE SETUP UTILITY ­ VERSION 1.20e ©2000 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced Setup Power Management Setup PCI / Plug and Play Setup Load Optimal Settings Load Best Performance Settings ESC: Quit : Select Item (Shift)F2 : Change Color F6: Optimal values F7: Best performance values Features Setup CPU PnP Setup Hardware Monitor Change Password Exit F5 : Old Values F10: Save&Exit You can use the cursor arrow keys to highlight any of the options on the main menu page. Press Enter to select the highlighted option. To leave the setup utility, press the Escape key. To cycle through the Setup Utility's optional color schemes hold down the Shift key and press F2. Some of the options on the main menu page lead to tables of items with installed values. In these pages, use the cursor arrow keys to highlight the items, and then use the PgUp and PgDn keys to cycle through the alternate values for each of the items. Other options on the main menu page lead to dialog boxes which require you to answer Yes or No by hitting the Y or N keys. If you have already made changes to the setup utility, press F10 to save those changes and exit the utility. Press F5 to reset the changes to the original values. Press F6 to install the setup utility with a set of default values. Press F7 to install the setup utility with a set of high-performance values. 24 3: BIOS Setup Utility Standard CMOS Setup Page Use this page to set basic information such as the date and time, the IDE devices, and the diskette drives. If you press the F3 key, the system will automatically detect and configure the hard disks on the IDE channels. AMIBIOS SETUP ­ STANDARD CMOS SETUP ©2000 American Megatrends, Inc. All Rights Reserved Date (mm/ dd/yy) : Mon May 22, 2000 Time (hh/mm/ss) : 14:26:53 Type Auto Auto Auto Auto LBA Blk PIO 32Bit Size Cyln Head WPcom Sec Mode Mode Mode Mode On On On On Pri Master : Pri Slave : Sec Master : Sec Slave : Floppy Drive A : 1.44MB 3 1/2 " Floppy Drive B : Not Installed Month : Jan ­ Dec Day : 01 ­ 31 Year : 1901 ­ 2099 ESC : Exit éê : Select Item PU/PD/+/- : Modify (Shift)F2 : Color F3 : Detect All HDD Date & Time Pri Master Pri Slave Sec Master Sec Slave Use these items to set the system date and time Use these items to configure devices connected to the Primary and Secondary IDE channels. To configure an IDE hard disk drive, choose Auto. If the Auto setting fails to find a hard disk drive, set it to User, and then fill in the hard disk characteristics (Size, Cyls, etc.) manually. If you have a CD-ROM drive, select the setting CDROM. If you have an ATAPI device with removable media (e.g. a ZIP drive or an LS-120) select Floptical. Use these items to set the size and capacity of the floppy diskette drive(s) installed in the system. Floppy Drive A Floppy Drive B 25 MS6391E Mainboard User's Manual Advanced Setup Page Use this page to set more advanced information about your system. Take some care with this page. Making changes can affect the operation of your computer. AMIBIOS SETUP ­ ADVANCED SETUP ©2000 American Megatrends, Inc. All Rights Reserved Trend ChipAwayVirus Frame Buffer Cache Control Share Memory Size 1s t Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Devices S.M.A.R.T. for Hard Disks BootUp Num-Lock Floppy Drive Swap Floppy Drive Seek Password Check Boot To OS/2 > 64MB Internal Cache External Cache System BIOS Cacheable Enabled Auto 8MB IDE-0 Floppy CDROM Yes Disabled On Disabled Disabled Setup No Enabled Enabled Disabled ESC F1 F5 F6 F7 : Quit : Select Item : Help PU/PD/+/- : Modify : Old Values (Shift)F2 : Color : Load Optimal values : Load Best performance values Trend ChipAway Virus Frame Buffer Cache Control This mainboard has built-in virus protection in the firmware. Use this item to enable or disable the built-in virus protection. This item appears when a Frame Buffer Cache card is installed in the ADIMM socket. The default setting, Auto, automatically sets the display memory size. The Manual setting uses the next item to manually set display memory size. This item lets you allocate a portion of the main memory for use by the onboard VGA display. Use these items to determine the device order the computer uses to look for an operating system to load at start-up time. If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first two locations. Enable this item if any IDE hard disks support the S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) feature. Share Memory Size 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Device S.M.A.R.T. for Hard Disks 26 3: BIOS Setup Utility BootUp NumLock Floppy Drive Swap Floppy Drive Seek Password Check This items determines if the Num Lock key is active or inactive at system start-up time. If you have two diskette drives installed and you enable this item, drive A becomes drive B and drive B becomes drive A. If you enable this item, your system will check all floppy disk drives at start up. Disable this item unless you are using an old 360KB drive. If you have entered a password for the system, use this item to determine if the password is required to enter the Setup Utility (Setup) or required both at start-up and to enter the Setup Utility (Always). Enable this item if you are booting the OS/2 operating system and you have more than 64MB of system memory installed. Leave this item enabled since all the processors that can be installed on this board have internal cache memory. Leave this item enabled since all the processors that can be installed on this board have external cache memory. If you enable this item, a segment of the system BIOS will be cached to main memory for faster execution. Boot to OS/2 > 64MB Internal Cache External Cache System BIOS Cacheable 27 MS6391E Mainboard User's Manual Power Management Setup Page This page sets some of the parameters for system power management operation. AMIBIOS SETUP ­ POWER MANAGEMENT SETUP ©2000 American Megatrends, Inc. All Rights Reserved Power Management/APM Standby Time Out (Minute) Suspend Time Out (Minute) Hot Key Power On LAN Card Power On Ring On Power On RTC Alarm Power On RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second Disabled Disabled Disabled Disabled Disabled Disabled Disabled 15 12 30 30 Quit : Select Item Help PU/PD/+/- : Modify Old Values (Shift)F2 : Color Load Optimal values Load Best performance values ESC F1 F5 F6 F7 : : : : : Power Management/APM Standby Time Out (Minute) Suspend Time Out (Minute) Hot Key Power On Use this item to enable or disable a power management scheme. If you enable power management, you can use the items below to set the power management operation. Both APM and ACPI are supported. This sets the timeout for Standby mode in minutes. If the time selected passes without any system activity, the computer will enter powersaving Standby mode. This sets the timeout for Suspend mode in minutes. If the time selected passes without any system activity, the computer will enter powersaving Suspend mode. If you enable this item, you can turn the system on by pressing hot keys (Ctrl + Alt + Back Space) on the keyboard. You must connect an ATX power supply and enable this function jumper in order to use this feature. 28 3: BIOS Setup Utility LAN Card Power On The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is traffic on the network adapter. You must use an ATX power supply in order to use this feature. The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Fax/Modem. You must use an ATX power supply in order to use this feature. The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system's RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature. Ring On Power On RTC Alarm Power On /Date /Hour /Minute /Second 29 MS6391E Mainboard User's Manual PCI / Plug and Play Setup Page This page sets some of the parameters for devices installed on the PCI bus and devices that use the system plug and play capability. AMIBIOS SETUP ­ PCI / PLUG AND PLAY SETUP ©2000 American Megatrends, Inc. All Rights Reserved Plug and Play Aware O/S Primary Graphics Adapter Allocate IRQ to PCI VGA Reserved Memory Size Yes PCI Yes Disabled ESC F1 F5 F6 F7 : : : : : Quit : Select Item Help PU/PD/+/- : Modify Old Values (Shift)F2 : Color Load Optimal values Load Best performance values Plug and Play Aware O/S Primary Graphics Adapter Allocate IRQ to PCI VGA Reserved Memory Size Enable this item if you are using an O/S that supports Plug and Play such as Windows 95 or 98. This item indicates if the primary graphics adapter uses the PCI or the AGP bus. The default PCI setting still lets the onboard display work and allows the use of a second display card installed in a PCI slot. If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. You set this value to No to free up an IRQ. This item lets you reserve a block of memory for any device that requires it. 30 3: BIOS Setup Utility Load Optimal Settings If you select this item and press Enter a dialog box appears. If you press Y, and then Enter, the Setup Utility loads a set of fail-safe default values. These default values are not very demanding and they should allow your system to function with most kinds of hardware and memory chips. Load Best Performance Settings If you select this item and press Enter a dialog box appears. If you press Y, and then Enter, the Setup Utility loads a set of bestperformance default values. These default are quite demanding and your system might not function properly if you are using slower memory chips or other low-performance components. Features Setup Page This page sets some of the parameters for peripheral devices connected to the system. AMIBIOS SETUP ­ FEATURES SETUP ©2000 American Megatrends, Inc. All Rights Reserved OnBoard FDC Enabled OnBoard Serial PortA 3F8h/COM1 OnBoard IR Port Disabled OnBoard Parallel Port 378h Parallel Port Mode SPP Parallel Port IRQ 7 Parallel Port DMA N/A OnBoard PCI IDE Both Ultra DMA Support Disabled OnBoard Audio/Modem Enabled OnBoard LAN Enabled USB Function Disabled USB Function for DOS Disabled Quit : Select Item Help PU/PD/+/- : Modify Old Values (Shift)F2 : Color Load Optimal values Load Best performance values ESC F1 F5 F6 F7 : : : : : OnBoard FDC Use this item to enable or disable the onboard floppy disk drive interface. 31 MS6391E Mainboard User's Manual OnBoard Serial PortA OnBoard IR Port Use this item to enable or disable the onboard COM1 serial port, and to assign a port address Use this item to define the protocol for an infrared port if you have installed an optional IR port. The choices are IrDA and ASKIR. Use this item to enable or disable the onboard LPT1 parallel port, and to assign a port address. The Auto setting will detect and available address. Use this item to set the parallel port mode. You can select SPP (Standard Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or ECP + EPP. Use this item to assign either IRQ 5 or 7 to the parallel port. Use this item to assign a DMA channel to the parallel port. The options are 0, 1 and 3. Use this item to enable or disable either or both of the onboard Primary and Secondary IDE channels. Use this item to set Ultra DMA support for IDE devices on the Primary or Secondary IDE channels. You must enable this or UDMA devices will not work at their intended speed. Use this item to enable or disable the onboard audio/modem chip. Use this item to enable or disable the onboard network interface. Enable this item if you plan to use the USB ports on this mainboard. Enable this item if you plan to use the USB ports on this mainboard in a DOS environment. Onboard Parallel Port Parallel Port Mode Parallel Port IRQ Parallel Port DMA Onboard PCI IDE Ultra DMA Support Onboard Audio/ Modem Onboard LAN USB Function USB Function for DOS 32 3: BIOS Setup Utility CPU PnP Setup Page This page lets you manually configure the mainboard for the CPU. The system will automatically detect the kind of CPU that you have installed and make the appropriate adjustments to the items on this page. Note : If you manually set the wrong speed and the system won't run properly, press the Page Up key while the system is booting and a default setting will replace the incorrect CPU setting. AMIBIOS SETUP ­ CPU PnP SETUP ©2000 American Megatrends, Inc. All Rights Reserved CPU Plug and Play CPU Brand VCCore Voltage CPU Speed CPU Base Frequency CPU Multiple Factory E-Plus CPU installed Auto 2.0V 450 MHz 100 MHz X4.5 Disable ESC F1 F5 F6 F7 : : : : : Quit : Select Item Help PU/PD/+/- : Modify Old Values (Shift)F2 : Color Load Optimal values Load Best performance values CPU Plug and Play CPU Brand; VCCore Voltage CPU Speed CPU Base Frequency CPU Multiple Factor E-Plus CPU installed Use this item to select the CPU Plug and Play function by auto-detect or user-define. These items display the CPU brand and CPU core voltage by the system automatic detecting. The item displays the internal clock speed of the CPU, based on the next two items. Use this item to set the external clock frequency for the CPU. Set the CPU clock based on the requirements of the CPU installed on the board. Use this item to set a multiplier for the CPU external frequency. The multiplier times the external CPU frequency sets the internal clock speed of the CPU, e.g. 100 MHz (external clock or "FSB") x 4.5 (muliplier) = 450 MHz (internal clock speed of the installed CPU). Enable this item if you plan to use the AMD EPlus CPU on this mainboard. 33 MS6391E Mainboard User's Manual Hardware Monitor Page This page sets some of the parameters for the hardware monitoring function of this mainboard. AMIBIOS SETUP ­ HARDWARE Monitor ©2000 American Megatrends, Inc. All Rights Reserved --- Hardware Monitor --CPU Temperature System Temperature CPU Fan Speed Chassis Fan Speed Vcore +1.800V Vcc3 Vcc +12V SB5V 30°C/86°F 30°C/86°F 2.000 V 1.800 V 3.300 V 5.000 V 12.000 V 5.000 V ESC F1 F5 F6 F7 : : : : : Quit : Select Item Help PU/PD/+/- : Modify Old Values (Shift)F2 : Color Load Optimal values Load Best performance values CPU / System Temperature FAN Speeds & Voltage Measurements These items display CPU/system temperature measurement. These items indicate cooling fan speeds in RPM and the various system voltage measurements. Change Password If you highlight this item and press Enter, a dialog box appears which lets you enter a Supervisor password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation. Press Enter after you have retyped it correctly. The password is then required to access the Setup Utility or for that and at start-up, depending on the setting of the Password Check item in Advanced Setup. 34 3: BIOS Setup Utility Change or Remove the Password Highlight this item, press Enter and type in the current password. At the next dialog box, type in the new password, or just press Enter to disable password protection. Exit Highlight this item and press Enter to save the changes that you have made in the Setup Utility configuration and exit the program. When the Save and Exit dialog box appears, press Y to save and exit, or press N to exit without saving. 35 4: Software & Applications Chapter 4 Software & Applications Introduction The support software CD-ROM that is included in the mainboard package contains all the drivers and utility programs needed to properly run our products. Please check all the README files for the latest information on installing and using the software. Using the PCI Sound Application 1. Before you install the PCI Sound drivers, make sure your Operating System has been installed, otherwise the PCI Sound might be detected as "Other device" by the device manager of your OS. 2. After the drivers are properly installed, choose the MULTIMEDIA icon in the CONTROL PANEL when you need to use the Software Wave-Table drivers as a MIDI output device. Select the MIDI page and click on "C-media SoftMidi Synthesis (Win98) / Driver (Win95)", then click "OK" to confirm. 3. A Windows application named Audio Rack is provided with the PCI Sound drivers, which gives you control over all the audio functions through a user interface that is as simple to use as a home stereo system. We recommend that you use the System Mixer in the Audio Rack software to control your computer's audio volume, recording device and the recording gain. 36 4: Software & Applications 4. If the devices that you are using require the MIDI port as the control interface, you need to select the MULTIMEDIA icon in the CONTROL PANEL. Select the MIDI page and click on "CM8738 MPU-401" (Win98) or "CM8738/C3DX PCI Audio External MIDI Port" (Win95), and then click "OK" to confirm. 5. For more information, refer to the PCI Sound manual in the CD which ships with this mainboard. The Four Speakers System The onboard Sound Pro audio system supports 2 wave channels (front/rear) known as the 4 speaker system. If you are running applications which use the DirectSound® 3D or A3D® audio interface, your system can simulate realistic 3D sound through a 4 speaker setup. Follow the steps below to install a 4-speaker setup. Speaker Installation Connect the front two speakers to the Line-out jack on the sound ports extension bracket. Connect the rear two speakers to the Linein/Rear jack on the sound ports extension bracket. The original Line-in can be moved to Aux. Speaker Position Set up your speakers similar to the following figure to get the best audio result. 37 MS6393E Mainboard User's Manual Mixer Setup There is a 4-speakers option in the Volume Control of the Mixer when you are setting up the PCI Audio Application. Click on the 4 SPK icon to enable this option. This means that the output to the rear speakers is sent through the Line-in/Rear jack. In order to avoid hardware conflicts, DO NOT enable this option when the Line-in/Rear jack is connected with a line-in device. While the 4 speakers mode is enabled, turn on/off the output of the front speakers and adjust the volume of the speakers so that the front/rear speakers have the same volume. Demo Execute the "Helicopter" demo in the C3D HRTF Positional Audio Demos of the PCI Audio Application. When you hear the helicopter flying behind you, it means that the rear speakers are working properly. 38