Mainboard User's Manual This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademarks IBM, VGA, and PS/2 are registered trademarks of International Business Machines. Intel, Pentium, Pentium-II, Pentium-III, MMX, and Celeron are registered trademarks of Intel Corporation. Microsoft, MS-DOS and Windows 95/98/NT are registered trademarks of Microsoft Corporation. Sound Blaster is a trademark of Creative Technology Ltd. PC-cillin and ChipAwayVirus are trademarks of Trend Micro Inc. AMI is a trademark of American Megatrends Inc. A3D is a registered trademark of Aureal Inc. Gamut is a registered trademark of Formosoft International Inc. SuperVoice is a registered trademark of Pacific Image Communications Inc. MediaRing Talk is a registered trademark of MediaRing Inc. Other names used in this publication may be trademarks and are acknowledged. Copyright © 2000 All Rights Reserved MS7308D/E, V1.6 S63X/JUNE 2000 MS7308D/E Mainboard User's Manual Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: q Reorient or relocate the receiving antenna. q Increase the separation between the equipment and the receiver. q Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected. q Consult the dealer or an experienced radio/TV technician for help. Shielded interconnect cables and shielded AC power cable must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system's manufacturer could void the user's authority to operate the equipment. Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: q This device may not cause harmful interference, and q This device must accept any interference received, including interference that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada. II MS7308E Mainboard User's Manual Table of Contents Chapter 1: Introduction ..............................................................1 Key Features......................................................................2 Package Contents ...............................................................5 Static Electricity Precautions ...............................................6 Pre-Installation Inspection...................................................6 Chapter 2: Mainboard Installation ...............................................7 Mainboard Components......................................................8 Install A CPU ....................................................................9 Install Memory................................................................. 10 Setting Jumper Switches ................................................... 11 Install the Mainboard........................................................ 13 Optional Extension Brackets............................................. 14 Install Other Devices........................................................ 15 Expansion Slots................................................................ 17 Chapter 3: BIOS Setup Utility .................................................. 19 Introduction ..................................................................... 19 Running the Setup Utility.................................................. 20 Standard CMOS Setup Page ............................................. 21 Advanced Setup Page ....................................................... 22 Power Management Setup Page ........................................ 24 PCI / Plug and Play Setup Page ......................................... 26 Load Optimal Settings ...................................................... 27 Load Best Performance Settings ........................................ 27 Features Setup Page ......................................................... 28 CPU PnP Setup Page ........................................................ 30 Hardware Monitor Page.................................................... 31 Change Password............................................................. 31 Exit.................................................................................. 32 Chapter 4: Software & Applications .......................................... 33 About the Software .......................................................... 33 Folders for this Mainboard................................................ 33 Running the Support CD-ROM......................................... 34 Utility Folder Installation Notes ........................................ 34 Mainboard (MS7308D/E) Installation Notes ...................... 35 III MS7308D/E Mainboard User's Manual Appendix A: Gamut .............................................................A1 Introduction ....................................................................A2 Before Installing .............................................................A3 Installation .....................................................................A4 Produce MP3 file Use CD-Cashier ................................A5 Play MP3 file Use Musician .........................................A7 Play music CDUse 3DFS-ACD .....................................A8 Play MIDI file Use Midier ............................................A9 Recording audio dataUse Voice-Catcher .................... A10 IV 1: Introduction Chapter 1 Introduction This mainboard has a Socket 370, which uses either an Intel PPGA (Plastic Pin Grid Array) Celeron or FCPGA Pentium III processor. This mainboard supports front-side bus speeds of 66MHz, 100MHz or 133MHz. This mainboard uses the SiS 630 chipset which provides CPU Plug & Play through firmware, integrates a 128-bit AGP Graphics Accelerator and has an embedded 10BaseT/100BaseTX Network Interface. The mainboard has a built-in PCI 3D Sound System. There is an AMR slot for the AMR device cards .In addition, the mainboard has a full set of ATX I/O Ports including PS/2 keyboard and mouse ports, two USB ports, a parallel port, a serial port and a VGA port. And three extra USB ports can be added using the Extended USB Module that connects to the mainboard. This mainboard has all the features you need to develop a powerful multimedia workstation that is network ready, and has built-in communications. The board is Micro-ATX size and has power connector for an ATX power supply. 1 MS7308D/E Mainboard User's Manual Key Features The key features of this mainboard include: Socket-370 Processor Support Supports PPGA Celerons from 300MHz to 600MHz. FCPGA Pentium III CPUs are supported Supports 66MHz, 100MHz or 133MHz FSB All processors are automatically configured using firmware and a synchronous/asynchronous Host/DRAM Clock Scheme. Memory Support Two DIMM slots for 168-pin SDRAM memory modules Support for 66MHz, 100MHz, & 133MHz memory bus Maximum installed memory is 2 x 512MB = 1 GB Expansion Slots Two 32-bit PCI slots One AMR slot for a special audio/modem riser card Onboard IDE channels Primary and Secondary PCI IDE channels Support for PIO (programmable input/output) modes Support for Multiword DMA modes Support for Bus Mastering and Ultra DMA 33/66 modes Power Supply and Power Management ATX power supply connector ACPI and previous PMU support, suspend switch, keyboard power on/off Supports Wake on Modem, Wake on LAN and Wake on Alarm 2 1: Introduction Built-in Graphics System Onboard 128-bit 2D/3D 100MHz Host interface AGP Graphics Accelerator Complies with AGP 1x,2x,4x Shared memory architecture allows a maximum of 64 MB main memory to act as frame buffer Supports high resolutions up to 1920x1200 16M colors, up to 2048x2048 Texture size and Virtual screen up to 4096x4096 Supports hardware DVD Accelerator Sound System Complies with the PC99 audio specification 16-bit CODEC for full-duplex playback and recording Driver support for Windows 95/98/2000/NT 4.0 Provides MPU-401 Game/MIDI port and legacy Sound Blaster 16 support Downloadable Wave-table Synthesizer supports Direct Music® 48KHz sampling rate and measured 90dB audio quality Onboard I/O Ports Provides PC99 Color Connectors for easy peripheral device connections Floppy disk drive connector with 1Mb/s transfer rate One serial port with 16550-compatible fast UART One parallel port with ECP and EPP support Five USB ports (three for optional) and two PS/2 ports for keyboard and mouse One infrared port connector for optional module Built-in Ethernet LAN Optional 10BaseT/100BaseTX Ethernet LAN LAN controller integrates Fast Ethernet MAC and PHY compliant with IEEE802.3u 100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD standards Compliant with ACPI 1.0 and the Network Device Class Power Management 1.0 3 MS7308D/E Mainboard User's Manual High Performance provided by 100Mbps clock generator and data recovery circuit for 100Mbps receiver Onboard Flash ROM Automatic CPU and board configuration Supports Plug and Play configuration of peripheral devices and expansion cards Built-in virus protection using Trend's ChipAwayVirus provides boot process virus protection. Bundled Software PC-Cillin provides automatic virus protection under DOS, Windows 95/98 SuperVoice is data, fax and voice communication software Gamut provides professional audio features included MP3 encoding/playback MediaRing Talk provides PC to PC or PC to Phone internet phone communication S-YXG50 is music synthesizer software to playback MIDI files on the system Dimensions Micro-ATX form factor (24.4cm x 19cm) 4 1: Introduction Package Contents Your mainboard package ships with the following items: q q q q q q The mainboard This User's Guide 1 UDMA/66 IDE cable Floppy disk drive cable Support software on CD-ROM disk 10/100BaseTX Ethernet LAN ( Only for MS7308E M/B ) Optional Accessories You can purchase the following optional accessories for this mainboard. q Extended USB module 5 MS7308D/E Mainboard User's Manual Static Electricity Precautions Components on this mainboard can be damaged by static electricity. Take the following precautions when unpacking the mainboard and installing it in a system. 1. Keep the mainboard and other components in their original static-proof packaging until you are ready to install them. 2. During installation, wear a grounded wrist strap if possible. If you don't have a wrist strap, discharge static electricity by touching the bare metal of the system chassis. 3. Handle the mainboard carefully by the edges. Avoid touching the components unless it is absolutely necessary. During installation put the mainboard on top of the static-protection packaging it came in with the component side facing up. q Pre-Installation Inspection 1. Inspect the mainboard for damage to the components and connectors on the board. 2. If you suspect that the mainboard has been damaged, do not connect power to the system. Contact your mainboard vendor and report the damage. 6 2: Mainboard Installation Chapter 2 Mainboard Installation To install this mainboard in a system, follow the procedures in this chapter: q q q q q q q Identify the mainboard components Install a CPU Install one or more system memory modules Verify that a ...