User manual MEDIALINE M42LD

USER'S Manual (Ver.1.0) Model : Medialine L42LD / L32LD Contents Before using this product Safety Instruction List of Features The names of each part -Front Panel Buttons -Rear Panel Jacks Remote Controller -Installing Batteries -The Name of Each Part Installation Connecting an Outdoor Terrestrial Antenna / Cable Television Network TV network Connecting VCR Connecting Cable Box / Satellite Receiver Connecting DVD Player / Video Game Machine Connecting a PC TV Function Getting Started Channel Edit and Source Select Scanning Channels (Automatic) Channel Edit ­ Store or Delete the channels Using Favorite (FAV.) Channel Function Displaying EPG (Electronic Program Guide) Viewing the Information Changing the Input Mode Viewing the Current Connected External Devices Picture and Sound Configuration Adjusting the Aspect Ratio Changing the Preset Picture Mode Customizing the Picture Adjusting Color Tone Changing the Preset Sound Mode Adjusting the Equalizer Automatic Volume Level Control To set MTS (Multi Track Sound) Mode Additional Function Changing the OSD Menu language Setting Blue Back Screen Setting the Current Time (Time Zone) Automatic Power on/off (On Timer / Off Timer) Setting the Sleep Timer Pixel Shift DNR (Digital Noise Reduction) PIP Adjusting the Size of Sub picture Changing Input mode of Sub picture Adjusting the position of Sub picture Swapping the main with sub picture Parental Rating Control (V-Chip) Viewing Closed Caption Adjusting PC Picture Settings Using as a PC Monitor Check the current Resolution and Frequency rate Automatic Adjustment of the PC picture Adjusting Picture Position Adjusting the PC Picture Settings Adjusting the Color Tone Adjusting the Frequency / Fine Tune Trouble Shooting -------------------------------------------------------------------------Before using this product Safety Instructions PLEASE READ AND OBSERVE ALL THE WARNINGS AND CAUTIONS IN THIS USER' S MANUAL AND RETAIN IT FOR FUTURE REFERENCE. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance Do not throw your product in the garbage - save the environment WARNING ·Unplug this product from the wall outlet immediately when it smokes or makes a strange smell. ·Do not block any ventilation openings. (This can result in a risk of fire or electric shock.) ·Do not overload wall outlets or extension cords (This can result in a risk of fire or electric shock.) ·Connect at the receptacle certainly not to be shaken (This can result in a risk of heat and a fire if it is connected to the wall outlet imperfectly.) ·Do not use the uncovered cables. (This can result in a risk of fire or electric shock.) ·During a storm conditions (especially when there is lightning) unplug this product from the wall outlet and don't touch the antenna. (This can result in a risk of fire or electric shock.) ·Do not expose this product to direct sunlight and extreme. (This can result in a risk of fire.) ·Keep children away from this product not to hang on or go up on it. ·Leave batteries for remote control away from your young children. (They may swallow them.) ·Place this product in a well-ventilated place. (This can result in a risk of fire.) ·People over 2 persons must move this product. (It can be the reason of the wound because of the weight of goods.) ·Never put objects of any kind into this product and place heavy things on it. ·Place an antenna away from a high-voltage cable. · Please use a soft and dry cloth (not containing volatile matter) when you clean this product. (This can result in a risk of fire.) CAUTION ·Please use a soft and dry cloth when you clean this product. (This can result in a risk of electric shock) ·Should not be adhered to a power supply plug and receptacle. (This can result in a risk of fire) ·Do not use new batteries with old ones together. (This can result in a risk of electric shock) ·Do not place this product in the place to reach children's hands. ·Do not take out a power supply plug with the wet hand. (This can result in a risk of electric shock) ·Bend down the outdoor antenna cable to prevent the rain water flows and not to enter the room. (This can result in a risk of fire or electric shock) ·Maintain a suitable distance between you and a TV or monitor to protect your eye sight. (Your eye sight can get worse if you watch TV very nearly) ·Place remote control away from a humid or hot place because it is very minute device. ·If this product is not used for a long period of time, unplug the power cord. (This can result in a risk of fire or electric shock) ·Do not drop this product. Unplug the power cord and ask to Service Centre when it is broken. ·Do not cover this product with curtains or a tablecloth. (This can result in a risk of fire) ·Place the batteries rightly to the both sides (+,-) when you replace them. (The batteries can be explosive and you're wound) ·Do not place this product on the floor. (Children can push it down) ·Do not damage the power cord. (This can result in a risk of fire or electric shock) · The LCD panel is very high technology product with about million thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does affect the performance of your product. List of Features Digital Broadcasting Support This TV is designed to receive and display High Definition TV (1920x1080i) or Analog TV signal. Electronic Program Guide Electronic Program Guide (EPG) is the very convenient feature that enables you to check the Programs with reference to Date, Time, and Channels. Favorite Channel / Virtual Channel Favorite Channel: After scanning all the available channels on broadcast, you can sort or manage the channels as your favorite ones. Once they are registered as favorite, you can easily change the channels among them by pressing " FAV" button on remote controller Virtual Channel: Without this feature, normally, HD Supported Channel are stored and assigned at high number of channel. For Example, some channel in Analog is Channel Number 6 while its HD Channel is 83. However, with this feature, HD Channel will be assigned virtually as 6-1 and easily recognized while analog channel is 6. The Name of Each Part Front Panel Buttons Source Button Change Input Source: Video, Component, PC or HDMI, DTV/TV. Menu Button Display OnScreenMenu. Volume - Button / Set the value Adjust sound level or set the value while On Screen Menu is active. Volume + Button / Set the Value Adjusts sound level or set the value while On Screen Menu is active. Channel - Button / Navigating the menu. Change channel or navigate while On Screen Menu is active. Channel + Button / Navigating the menu Change channel or navigate while On Screen Menu is active. Power Button Turn on or off the TV. Rear Panel Jacks 7 1 2 3 4 5 6 8 9 10 11 12 13 14 1. Service port 2. HDMI 3. Audio Input (for HDMI-to-DVI Cable) 4. D-Sub 5. PC Audio Input 6. Component 1 7. Component 2 8. Audio Line Out 9. S-Video 10. AV 1 & 2 11. USB v.2.0 (for Service) 12. SPDIF (Optical) 13. SPDIF (Coaxial) 14. Antenna In Remote Controller Installing Batteries Remove the rear cover of the remote controller by pressing the arrow Symbol downwards and then pulling firmly to remove it. Insert two 1.5V of AAA type batteries by following polarities (+,-). Close the cover. Tip To confirm proper battery installation, press any button on the remote control and check the red LED on the remote control twinkles. The Name of Each Button 1 2 3 4 5 8 9 10 11 12 13 6 14 15 7 17 18 19 20 25 21 22 23 16 24 26 TV Function 1. POWER: Turn LCD TV on and off. 2. PIC.SIZE: Screen Size Change 3. PIC.MODE: Adjust the TV Picture by selecting one of the preset factory settings Before using this product 4. MTS (Multi Channel Television Stereo): Sound mode change to Stereo, Mono, or Separate Audio Program (SAP Broadcast) 5. S.MODE: Adjust TV Sound by selecting one of the factory settings. 6. NUMBER Buttons: Push to change channel. 7. -: Approach to Digital TV Channel (Virtual Channel, eg, 6-1) 8. MUTE: Temporarily cut off the sound. 9. PIP: Turn Picture-In-Picture on or off. 10. SLEEP: Set the sleep timer. 11. P.INPUT: Select the Input mode for the sub picture 12. STILL: Pause the moving Image. 13. P.POSITION: Change the position of sub Picture (PIP). 14. P.SIZE: Adjusts the sub picture (PIP) size. 15. P.SWAP: Exchange main with sub picture. 16. PRE-CH: Move to the previous channel. Mode Setting / Menu Selection 17. PC/HDMI: Select PC or HDMI mode. 18. DTV/TV: Select DTV or TV 19. MENU: Display "On Screen Display" Menu. 20. Direction Keys: Adjusts channels, volume level and navigate the menu. 21. AV.SEL: Change input source every time pushed. 22. SOURCE: Display the all the connected or available external devices on the screen. 23. EXIT: Terminated menu screen TV Control 24. EPG (Electronic Program Guide): Weekly Program Guide Display with reference to date, time and channels 25. FAV: Change among the channels assigned as favorite every time pushed.. 26. CC: Closed Caption ------------------------------------------------------------------------------------------Installation Connecting an Outdoor Air Antenna / Cable Television Network Outdoor Air Antenna with 75-ohm Round Lead Cable Television Network Connecting VCR Composite or S-Video Connection S-Video In AV1(Video/Audio In) How to Connect 1. Connecting Guide 1.1. Using the Composite Cable: When you connect Audio/Video composite cables, beware of the colors of the jacks. (Video is Yellow, Audio are in White and Red) 1.2. Using S-Video Cable: If the VCR, you have, supports S-Video Output, connect S-Video Input of the LCD to S-Video Output of the VCR and do the same in Sound cable (White and Red). To Watch VCR 1. Turn on the product, press [AV.SEL] button on the remote control to select `AV' or `S-Video' mode. (Or press [SOURCE] button to show and select the connected and available external devices on the screen)2. 2. Turn on the VCR, insert a video cassette then press [Play] button. Connecting Cable Box / Satellite Receiver Composite (Video / Sound) or S-Video connection Composite Cable S-Video Cable How to Connect 1. Connecting the Antenna Cable to Cable Box / Satellite Receiver: Plug the Antenna cable with 75-Ohm Round Lead into the Antenna Input terminal of the Cable Box / Satellite Receiver. 2. Connecting Guide 2.1. Using Composite (A/V) Cable -Video Connection: Connect the Video Input port of the LCD TV to the Video Output port of the Cable Box / Satellite Receiver with the Composite cable. The color of Video Cable and Output Port are in Yellow. -Sound Connection: Connect the Sound Input port of the LCD TV to the Sound Output Port of the Cable Box / Satellite Receiver with Composite cable. The color of Sound Cable and Output Ports are in White and Red. 2.2. Using S-Video Cable (While S-Video is supported) -Video Connection: Connect the S-Video Input port of the LCD TV to the S-Video Output port of the Cable Box / Satellite Receiver by using S-Video cable. -Sound Connection: Connect the Sound Input port of the LCD TV to the Sound Output Port of the Cable Box / Satellite Receiver with Sound Cable. The color of Sound Cable and Output Ports are in White and Red. To watch Cable / Satellite Broadcast 1. Turn on the LCD TV and press [AV.SEL] button on the remote control until the connected Input Source is selected. (Or press [SOURCE] button to show and select the connected and available external devices on the screen) 2. Turn on the Cable Box / Satellite Receiver and select the channel you would like to watch. Connecting Cable Box / Satellite Receiver DVI to HDMI Connection How to Connect 1. Connecting the Antenna Cable to Cable Box / -Satellite Receiver: Plug the Antenna cable with 75-Ohm Round Lead into the Antenna Input terminal of the Cable Box / Satellite Receiver. 2. Connecting Guide 2.1. Using Component Cable (Green, Blue & Red Color). -Video Connection: Connect the Component Input port of the LCD TV to the Component Output port of the Cable Box / Satellite Receiver with the Component cable. The color of the Cable and the Output Ports are in Green, Blue & Red Color accordingly. -Sound Connection: Connect the Sound Input port of the LCD TV to the Sound Output Port of the Cable Box / Satellite Receiver with Composite cable. The color of Sound Cable and In/Out Ports are in White and Red. In this case, the sound ports are generally located by the component ports. *Component Connection is also required to connect sound L/R properly. If fails, there will be no sound. 2.2. Using HDMI (Source) to HDMI Cable: This is only where both of devices have HDMI Port. Since HDMI deliver sound signal with its video signal, it does not require any additional sound connections *What is HDMI? The high-definition Multimedia Interface (HDMI) is an industry-supported uncompressed, all digital audio/video interface. HDMI provides an interface between any compatible digital audio/video source, such as a Set-top Box, DVD Player and A/V Receiver and a compatible digital audio/video monitor, such as a digital television (DTV). HDMI supports standard, enhanced or high definition video, plus multi-channel digital audio on a single cable. *HDMI to HDMI connection does not require additional sound cable connection while DVI (source)-to-HDMI connection needs additional sound cable connection (L/R) because DVI does not deliver sound signal in it. 2.3. Using DVI (Source) to HDMI Cable: This is applicable if there only DVI output exists on Cable Box / Satellite Receiver. In this case DVI to HDMI Cable can be used to connect each other. Unlike HDMI to HDMI as mentioned in the above, DVI does not deliver sound signal. Additional sound connection should be done. -Video Connection: Connect the HDMI Input port of the LCD TV to the DVI Output port of the Cable Box / Satellite Receiver with the DVI to HDMI cable. -Sound Connection: Connect the Sound Input port of the LCD TV to the Sound Output Port of the Cable Box / Satellite Receiver with Composite cable. The color of Sound Cable and Output Ports are in White and Red. In this case, the sound ports are generally located by the HDMI ports. To watch Cable / Satellite Broadcast 1. Turn on the LCD TV and press [AV.SEL] button on the remote control until the connected Input Source is selected. (Or press [SOURCE] button to show and select the connected and available external devices on the screen) 2. Turn on the Cable Box / Satellite Receiver and select the channel you would like to watch. Connecting DVD Player / Video Game Machine Component Connection HDMI Connection DVI to HDMI Connection How to Connect 1. Connecting Guide 1.1. Using Component Cable (Green, Blue & Red Color). -Video Connection: Connect the Component Input port of the LCD TV to the Component Output port of the DVD Player / Video Game Machine with the Component cable. The color of the Cable and the In/Out Ports are in Green, Blue & Red Color accordingly. -Sound Connection: Connect the Sound Input port of the LCD TV to the Sound Output Port of the DVD Player / Video Game Machine with Composite cable. The color of Sound Cable and Output Ports are in White and Red. In this case, the sound ports are generally located by the component ports. *Component Connection is also required to connect sound L/R properly. If fails, there will be no sound. 1.2. Using HDMI (Source) to HDMI Cable: This is only where both of devices have HDMI Port. Since HDMI deliver sound signal with its video signal, it does not require any additional sound connections 1.3. Using DVI (Source) to HDMI Cable: This is applicable if there only DVI output exists on DVD Player / Video Game Machine. In this case DVI to HDMI Cable can be used to connect each other. Unlike HDMI to HDMI as mentioned in the above, DVI does not deliver sound signal. Additional sound connection should be done. -Video Connection: Connect the HDMI Input port of the LCD TV to the DVI Output port of the DVD Player / Video Game Machine with the DVI to HDMI cable. -Sound Connection: Connect the Audio In port of the LCD TV to the Audio Out Port of the DVD Player / Video Game Machine with Composite cable. The color of Sound Cable and Output Ports are in White and Red. In this case, the Audio In ports are generally located by the HDMI ports. To watch DVD / Play Video Game Machine 1. Turn on the LCD TV and press [AV.SEL] button on the remote control until the connected Input Source is selected. (Or press [SOURCE] button to show and select the connected and available external devices on the screen) 2. Turn on the DVD Player and press [Play] button Connecting a PC D-Sub Connection How To Connect 1. Connecting Guide 1.1. Using D-SUB Cable: The most common way to use TV as a computer monitor -Video Connection: Connect the D-Sub In port of the LCD TV to the D-Sub Out port of the PC with the D-Sub cable. -Sound Connection: Connect the Sound In port of the LCD TV to the Sound Out port of the PC with Stereo Jack (Male to Male Headphone Jack Type) Cable. In this case, the sound ports are generally located by the D-Sub ports. To use it as a Computer Monitor 1. Connected through D-SUB Cable: Turn on and press [PC] button on Remote Control. (Or press [SOURCE] button to show and select the connected or available external devices on the screen. Select [PC]) ---------------------------------------------------------------------------------------TV Function Getting Started 1. Plug the Power Cable into AC In on the back of the TV 2. Press [Power] button on the Remote Controller or Front Panel of it. 3. Change Channel by pushing 'Channel +/-[ / ] button or number keys on the Remote Controller. / ] to adjust volume level. 4. Press `[Volume +/- [ *The current source mode and the channel number are shown up in the top-right corner of the screen. *Check the Antenna and Power Cable Connection if there is no display. --------------- Channel Scanning Channels (Automatic) This will scan all the available Channels. Channel scan should be done before using this product. *You should set the proper TV reception method, `Air' for outdoor air antenna and `STD, HRC & IRC' for your cable TV System. For the cable system, please contact your local cable TV provider. 1. Press MENU [ ] button on the remote control and navigate by pushing Channel +/- Keys to select `Channel' menu. 2. Press Volume [ Menu. / ] button to enter [Channel ] 3. Set your TV reception method among [Air/Cable/Hrc/Irc], Tip To do channel search, set the TV reception method, such as `Air', `Cable STD', `Cable Hrc' or `Cable Irc'. All the available Digital (ATSC) and Analog (NTSC) TV channels are scanned in each TV reception method and stored after the channel scan. When you watch TV, the channel system is set to DTV as a factory default and can be changed by pushing DTV/TV button on Remote Controller. 4. Push Channel +/- button to select [Autosearch] and press Volume / ] button again, and then the channels are searched [ automatically 5. Press [ / ] button to display the scanned channels. Only scanned channels are on display Tip All the current stored channels will be replaced with new channel information after doing `Auto Search'. However, this is only applicable when at least one new channel is scanned and stored. If it is terminated without any newly scanned channel, the previous channel information is kept. Channel Edit ­ Store or Delete the channels. 1. Press MENU [ ] button and select [Channel / ] menu by manipulating Channel [ [ ] button to get into. ] button and then, press Volume 2. In this menu, select [Channel Edit] by pressing Channel [ / ] button. ] 3. Channel Edit menu will be up when you press Volume [ button. Tip Channel Edit Mode manages Digital and Analog channels separately. (For example, only available DTV channels will be displayed in DTV mode, no analog channels at all). It is recommend setting the channel system (Analog/Digital) properly before you edit Channel. (Digital Channel) (Analog Channel) *The right side of the menu is for the current available or stored channels. Before you watch TV, as mentioned, channel scan should be done. To Store/Memorize a Channel, Press INFO (OK) [ Press INFO (OK) [ ] button on the one you select and then input Channel Number. ] button again and the channel configurations will be stored. 1. 2. To delete a Channel, 1. 2. Select the channel you would like to delete by manipulating Volume [ [ / ] button on Remote Controller. Press `-` button to delete the selected one. / ] or Channel Using Favorite (FAV.) Channel Function Favorite Channel Function is to ease channel change among your frequent watching or favorite channel by separately memorizing them in FAV. To Register as Favorite Channel 1. Press Channel [ / ] button or Volume [ / ] button to select the channel you would like to register in the available channel menu on the right side of display. 2. Press `FAV' on the selected one to register it as a favorite channel 3. The registered one is displayed in `Favorite Channel', located at the bottom left of the screen (Digital TV Channel) (Analog TV Channel) *After you finish favorite channel registration, by each pressing of FAV, you can change the channels between them. Tip FAV function manages Digital TV Channels and Analog ones separately. For instance, if FAV button is pressed under Digital TV System (DTV), only DTV channels that is preset channels are displayed. To use in Analog, press DTV/TV button on Remote Controller to change the mode to Analog and push FAV. Displaying EPG (Electronic Program Guide) EPG is available only when you watch Digital TV. EPG displays TV Programs with reference to a channel and time interval. 1. Press EPG button on the remote control during watching HD TV Program. 2. Press Channel [ / ] or Volume [ / navigate Programs with reference to each channel. ] button to 3. You can check the program schedule with reference to a channel and see program information by pushing `OK'. *Not every program has EPG information. The program with information has information icon in EPG. Viewing the Information The information identifies the current channel and status of certain audio and video settings. 1. Press INFO [ TV. ] button on the remote control during watching 2. The TV will display information on the channel, the type of sound and status of certain audio/video settings. 3. The information screen automatically disappears after about ten seconds or manually by pushing INFO [ ] button again. Tip The information window will disappear about 10 seconds later. Changing the Input mode This explains how to change and watch other Input Sources by pushing AV.SEL buttons 1. Press [AV.SEL] button on the Remote control. 2. You can change Input Source to be displayed every time you press the button. * You can select TV, PC/HDMI Mode directly by pressing [TV/DTV] / [PC/HDMI] button on the remote control accordingly. Tip Concerning how to connect external devices, you can consult "Installation" section. Viewing the Current Connected External Devices This explains how to change and watch other Input Sources by pushing `Source' button. 1. Press [Source] button on the remote control. The status of input source will appear. 2. Press Channel [ / ] button and then push Info [ button to change the input source. ] *The Connected (Available) external devices or port is brightened with "Connected" message while deactivated ones are in gray and with "Not Connected" message. --------------- Picture & Sound Configuration Adjusting the Aspect Ratio This explains how to change Aspect Ratio to `4:3, 14:9, Panorama and Wide'. Press [PIC.SIZE] button on the remote control. The Aspect Ratio is changed in turn as you press the button. Wide Panorama Zoom 4:3 14:9 To change the Aspect Ratio in OSD Menu 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Picture]' [ ] button. / ] ] menu and push Volume [ 3. In [Picture] menu, select [Size] with Channel [ button. 4. Change Aspect Ratio by pressing Volume [ / ] button. Tip Wide Panorama Zoom 4:3 14:9 Convert display ratio to 16:9 Panorama Mode Zooming the original Image twice big (Press Channel [ / ] button to move the center position of picture. Convert display ratio to 4:3 Convert display ratio to 14:9 Changing the Preset Picture Mode Your TV has several factory presets which allow you to control the picture. Press [PIC.MODE] button on the remote control. The picture mode is changed as you press the button. Custom Dynamic Standard Movie Mild To change the Picture Mode in OSD Menu 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Picture]' [ ] ] button. menu and push Volume [ 3. In [Picture] menu, select [Picture Mode] with Channel [ / ] button. / ] button. 4. Change the Picture mode by pressing Volume [ Customizing the Picture You can adjust Brightness, Contrast, Sharpness or the depth of Color. 1. Press MENU [] button on the remote control. 2. Press Channel [ / ] button to select `[Picture]' [ ] button. ] menu and push Volume [ 3. In [Picture] menu, select [Picture Mode] with Channel [ / ] button and manipulating Volume [ until "Custom" appears. / ] button 4 Use Channel [ / ] button to select among Brightness, Contrast, Sharpness, Tint and Color and then adjust the values with Volume [ / ] button. Adjusting the Color Tone This explains how to change the tone of the screen. 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Picture]' [ ] ] button. menu and push Volume [ 3. In [Picture] menu, select [Color Tone] with Channel [ / ] button / ] button. 4. Change Color Tone Preset with Volume [ Changing the Preset Sound Mode This TV set offers five sound modes (Custom, Standard, Music, Movie, Speech). Press [S.MODE] button on the remote control. The mode is changed one by one every time you press it. (Custom Standard Music Movie Speech) To Change the Sound Mode in OSD Menu 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Sound]' [ ] ] button. menu and push Volume [ 3. In [Sound] menu, select [Sound Mode] with Channel [ / ] button. / ] button. 4. Change the Sound Mode by pressing Volume [ Adjusting the Equalizer This explains how to set and adjust equalizer. 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Sound]' [ ] button. / ] ] menu and push Volume [ 3. In [Sound] menu, select [Equalizer] with Channel [ button and push Volume [ ] button. 4. Select the Frequency to be set by pressing Channel [ button. 5. Adjust the level properly by pressing Volume [ button. / / ] ] Automatic Volume Level Control Auto Volume normalizes the different sound volume level that can be different in broadcast station. This lets you have adjusted mean value of volume level per channel. 1. Press MENU [ 2. Press Volume [ 3. Press Channel [ 4. Push Volume [ ] on the remote control to select [Sound] menu. ] button on [Sound] menu. / / ] button to select [Auto Volume]. ] button until [Auto Volume] is "on". Setting MTS (Multi Track Sound) Mode You can adjust the Stereo or MTS function manually. 1. Press [MTS] button on the remote control. Stereo / Mono You can select between `Stereo' and `Mono' when the Stereo broadcasting is received. ­ Stereo: Two speakers out (2 Channels, Left/Right) and the different sound per channel ­ Mono: Two speakers out but both channel has the same signal (the identical sound). Separate Audio Program You can select the SAP mode which is `Main sound', `Sub sound' or `Main+Sub sound' when the SAP broadcasting, which is usually a foreign translation, is received. ­ Main sound: Listen to main sound or language. ­ Sub sound: Listen to secondary sound or language instead of main. *Other input sources than TV Signal, MTS is working only in R, L or R/L Mix mode. ------------------------------Additional Function Changing the OSD Menu language You can change the OSD Menu Language. 1. Press MENU [ ] button on the remote controller 2. Press Channel [ menu and push Volume [ / ] button to select `[Set Up]' [ ] button / ] ] 3. In [Set Up] menu, select [Language] with Channel [ button. 4. Change Language by pressing Volume [ / ] button. Setting the Blue Back Screen If no signal is being received or the signal is very weak, a blue back screen is automatically displayed instead of the noisy image. 1. Press MENU [ ] button on the remote control. 2. Press Channel [ / ] button to select `[Setup]' [ ] menu and push Volume [ ] button to be in. / ] button. 3. Select [Blue Screen] by pressing Channel [ 4. Set `On' by pressing Volume [ / ] button. Setting the Current Time (Time Zone) Time Zone setting is required for setting the time and receiving EPG properly. Once system time is set, all the relevant functions such as timer are available. 1. Press MENU [ 2. Select Setup [ 3. Press Volume [ again. ] button on the remote control. ] menu by pressing Channel [ ] button, select `Time' with Channel [ / / ] button. ] button and press Volume [ ] button 4. In [Time Zone] menu, manipulate Volume [ ] button to select the region you live. Tip The current time can be check by pressing Info [ ] button on the remote controller. Automatic Power On and Off 1. Press MENU [ 2. Select Setup [ button. ] button on the remote control. ] menu by pressing Channel [ / ] 3. Press Volume [ [ / ] button, select `Time' with Channel ] button again.. ] button. ] button and press Volume [ 4. Select `On timer' or `Off timer' by pressing Volume [ 5. Set the time with Channel [ / ] button. Setting the Sleep Timer You can adjust the time for automatic system down. Press [Sleep] button. Sleep Timer is changed as following every time you press [Sleep] button. OFF30Min60Min90Min120Min150Min180Min To set the sleep timer in [Setup] menu, 1. Press MENU [ 2. Select Setup [ button. 3. Press Volume [ [ / ] button on the remote control. ] menu by pressing Channel [ / ] ] button, select `Time' with Channel ] button again / ] button. ] button and press Volume [ 4. Select [Sleep Timer] by pressing Channel [ 5. Set the timer with Volume [ / ] button ] button to save the changes and exit. 6. When configuration is done, press MENU [ Tip Time is automatically set, once you set the Time Zone and then watch a DTV channel. After Time is set, you can use On Timer and Off Timer functions. Tip The current time is automatically received or synchronized by Digital TV EPG Once Digital TV channel information is set and stored, it is not required for setting the time. PIXEL SHIFT Due to its fundamental and built-up technology of LCD, when it is turned on long time of period especially with a still image, it can have afterimage that does not disappear even though it is turned off. During watching TV, this can affect serious image quality problem. However, with this feature, each pixel of LCD is shifted to right or left minutely and regularly, surely impossible to be noticed by human eyes, to protect afterimage effect. 1. Press MENU [ ]on the remote control. 2. Select `PIXELSHIFT' in Setup [ ] menu. 3. Set `PIXELSHIFT' function `ON' by pressing Volume [ / ] button. Digital Noise Reduction When the incoming signal is weak or picture noise appears at moving image, DNR function helps to reduce the noise and eye strain by its filtering procedure. 1. Press MENU [ ] button on the remote control. 2. Select `DNR' in Setup [ ] menu. 3. Set `DNR' function `ON' by pressing Volume [ / ] button. PIP (Picture In Picture) PIP is the function to display two different input source simultaneously. 1. Press [PIP] on the remote control. [PIP] is changed as following every time you press [PIP] button On -> Off To set PIP in On Screen Display Menu, 1. Press MENU [ ] button on the remote control. 2. Select PIP [ button. 3. Press Volume [ [ / ] button ] menu by pressing Channel [ / ] ] button and select [PIP] by pressing Channel 4. Set PIP to "On" with Volume [ / ] button * Please check the following PIP combination table of Main and Sub picture. (`Graphic-in-Graphic or Video-in-Video' is not supported) SUB MAIN TV AV1 S-Video AV2 DTV Component1 Component2 PC HDMI TV AV1 S-VIDEO AV2 DTV Component 1 Component 2 PC HDMI X X X X X O O O O X X X X O O O O O X X X X O O O O O X X X X O O O O O X O O O X X X X X O O O O X X X X X O O O O X X X X X O O O O X X X X X O O O O X X X X X Adjusting the Size of Sub picture Press [P.SIZE] button on the remote control. The size is changed in the following order each press. `Small DOUBLE DOUBLE2'. To adjust the size in On Screen Display Menu, 1. Press MENU [ 2. Select PIP [ button. 3. Press Volume [ [ / ] button. ] button on the remote control. ] menu by pressing Channel [ / ] ] button and select [Size] by pressing Channel 4. Press Volume [ / ] button to adjust the size. Changing Input mode of Sub picture You can change the input source of sub picture. Press [P.INPUT] button on the remote control. The input source is changed as you press the button. To change the input source in On Screen Display Menu, 1. Press MENU [ 2. Select PIP [ button. ] button on the remote control. ] menu by pressing Channel [ / ] 3. Press Volume [ Channel [ / ] button and select [Input Source] by pressing ] button. / ] button to change input source. 4. Press Volume [ (To adjust the input source of Sub picture, PIP should be active.) Adjusting the position of Sub picture You can change the position to `Up', `Down', `Left', `Right'. The position of Sub picture is changed as you press [P.POSITION] button on the remote control. To adjust the position in On Screen Display Menu, 1. Press MENU [ ] button on the remote control. 2. Select PIP [ ] by pressing Channel [ / ] / / ] button. 3. Press Volume button. [ 4. Select [Position] by pressing Channel [ ] button. 5. Adjust the position by pressing Volume [ / ] button (To adjust the position of Sub picture, PIP should be active.) Swapping the main with sub picture in PIP mode Press [P.SWAP] button on the remote control. To do this in On Screen Display Menu, 1. Press MENU [ ] button on the remote control. 2. Select PIP [ ] by pressing Channel [ ]. / / ] button. 3. Press Volume button. [ 4. Select [SWAP] by pressing Channel [ 5. Pressing Volume [ / ] button. ] button to swap the picture Viewing Closed Caption Closed Caption feature is to display On Screen Text Messages during watching TV. This feature is available in both analog and digital broadcast. 1. Press MENU [ ] on the remote control, select Setup [ / ] button and press ] menu by manipulating Channel [ volume [ ] button. / 2. Press Channel [ Volume [ ] button ] to select [Caption] and then 3. `Caption' sub menu will appear. *Sub Menus of Caption. Caption: Turn the feature on or off. This can be set by Volume [ / ] button. / / ] button. ] button to change it. Caption Box: Set the Text Box. You can turn it on or off with Volume [ Caption Box Color: change the color of Caption Box. Press Volume [ Parental Rating Control (V-Chip) V-chip feature automatically locks TV Programs (TV Parent Guide Lines) or Movie (MPAA) that is considered as inappropriate for children. To activate, deactivate or set the rating, you should enter a PIN (Personal ID Number). 1. Press [MENU] button to display the menu. 2. Press Channel [ 3. Press Channel [ / / ] button to select `Setup', and then press volume [ ]button to select `V-Chip', and then press Volume [ / / ] ] 4. The message "Enter PIN" will be appear. Enter your four digit PIN Number. The V-Chip screen will appear. (*The default Pin Number of a new TV set is `0000'.) *To change PIN Number, select Change Pin Number menu and then the menu will appear. Choose and enter 4 digits. How to set up restrictions using the "TV Parental Guidelines". 1. Press Channel [ / ] button to select `TV Parent Guide Lines' and then push Volume [ The menu will appear. You can set up the restrictions in this menu. *Restriction Categories based on six aged base. TV-Y Young Children TV-Y7 Children 7 and over TV-G General Audience TV-PG Parental Guidance TV-14 Viewers 14 and Over TV-MA Mature Audience For instances, if you block TV-Y, TV-Y7 will automatically be blocked and similarly, if you block the TV-G, all the categories in "young adult" (TV-Y, TV-Y7, TV-G, TV-PG, TV-14, and TV-MA) will be blocked. *Each Restriction Category has additional options, sub-ratings. FV: Fantasy Violence D: Sexually Suggestive Dialog / ] button. L: Adult Language S: Sexual Situation V: Violence V-Chip will automatically block certain sub-categories that are more restrictive. For example, if you block "L" sub-rating in TV-PG, then the "L" sub ratings in TV-14 and TV-MA will automatically be blocked. How to set up restrictions using the "MPAA". / ] button to select `MPAA Rating" and then push Volume [ / ] button. The menu 1. Press Channel [ will appear. You can set up the MPAA restrictions in this menu. *Restriction Categories based on six aged base. G General Audience (No Restrictions) PG Parental Guidance Suggested PG-13 PG-13 (Parents Strongly Cautioned) R R (Restricted. Children under 17 should be accompanied by an adult) NC-17 No Children under age 17. X X (Adults Only) NR Not Rated _____________________________________________________Adjusting PC Picture Settings Using as a PC Monitor This LCD TV is designed to be used as a PC Monitor. Concerning the Maximum Resolution, please refer to specification table in Appendix. Since it has driver software implemented, you don't have to install any additional software. Just PLUG N' PLAY!!! Tip To use it as a PC Monitor, your PC and TV should be connected via D-Sub Cable (15 Pin Analog). For details, please check the Installation section. Check the current Resolution and Frequency rate This will display information on current resolution and frequency rate on the bottom of the screen. To check, press MENU [ ] button in `Picture [ ] menu'. 1. Select `PC' and press Volume [ / ] button. 2. The resolution and Frequency rate are displayed on the bottom of the screen. Automatic Adjustment of the PC picture This is the function that the LCD TV System finds the optimal value for adjustment and automatically applies it. Use this function when the position of WINDOWS image is not centered or the characters on the screen are not clear. 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Picture]' [ ] button. / ] button ] menu and push Volume [ 3. In [Picture] menu, select [PC] with Channel [ and push Volume [ ] button.. 4. Select `Auto Adjustment' by pressing Channel [ button / ] 5. Press Volume [ ] button and then Automatic adjustment starts. Setting the Position of PC Picture You can adjust the position of a PC picture manually. Use this function when the picture is not centered or shifted to sides. 1. Press Volume [ 2. Press Channel [ / / ] button. ] button and then select `Position' by pressing Volume [ / ] button. / ] button. / ] button. 3. The position adjustment screen is displayed when you press Volume [ 4. Adjust the position by pressing Channel [ / ] button and Volume [ Adjusting the PC Picture Settings You can adjust the PC picture, by selecting the preset values or user value. In this Menu, you can adjust Brightness, Contrast and Sharpness. To use the preset values, 1. Press MENU [ ] button on the remote control. 2. Press Channel [ / ] button to select `[Picture]' [ ] button. / ] menu and push Volume [ 3. Select [Picture Mode] by pressing Channel [ and adjust the value with Volume [ / ] button. ] button Adjusting the Color Tone You can adjust the color tone of the PC Picture. 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Picture]' [ ] menu and push Volume [ ] button. 3. Select [Color Tone] by pressing Channel [ 4. [Color Tone] Menu will display. 5. Adjust RGB by pressing Channel [ / / ] button and press Volume [ ] button. ] button and Volume [ / ] button. Adjusting the Frequency / Fine Tune Use this function to adjust the Frequency range or Phase. To adjust the Frequency by using On Screen Display Menu, 1. Press MENU [ 2. Press Channel [ ] button on the remote control. / ] button to select `[Picture]' [ ] button. / ] button and press ] menu and push Volume [ 3. Select [PC] by pressing Channel [ Volume [ 4. Press Channel [ 5. Press Volume [ / / ] button. ] button to select [Frequency] or [Phase]. ] button to adjust the Frequency range or phase ___________________________________________________Trouble Shooting If the TV seems to have a problem, first check the following list of possible problems and solutions before contacting a service center. If none of these troubleshooting tips apply, do not attempt to service the product by yourself. Call an service center. · Symptoms that may appear to be a problem