USB Graphics tablet © 2004 Medion®. All rights reserved. Trademarks: Microsoft, MS-DOS and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Other trademarks are property of their respective owners. Artwork is for illustrative purposes only. Actual product appearance may vary. Medion can not be held liable for misprints or typos. CONTENTS Safety and Maintenance .........................................................3 Ergonomics.............................................................. 4 Inventory .................................................................. 4 Technical data ............................................................ 5 System requirements .................................................. 5 Usage ....................................................................... 5 Getting Started........................................................................6 Insert the Battery into the pen...................................... 6 Insert the battery into the cordless mouse...................... 6 Used batteries - waste disposal .................................. 7 Graphics tablet diagram............................................... 7 Installation of the graphics tablet .................................. 8 Driver installation ..................................................... 9 Installation of the applications .................................. 10 Uninstalling applications .......................................... 11 Configuring the Graphics tablet ................................... 11 Calibrating the drawing pen ..................................... 11 Customer service ..................................................................12 What to do in the event of problems ............................ 12 Basic hints............................................................. Troubleshooting ..................................................... Technical Support ................................................... Additional Support .................................................. 12 12 13 13 Warranty ...............................................................................14 ii SAFETY AND MAINTENANCE Keep these instructions with your graphics tablet at all times. The proper set up, use and care can help extend the life of your graphics tablet. In the event that you transfer ownership of this device, please provide these instructions to the new owner. Whenever you edit your data, make backup copies on an external data medium (e.g., floppy disks, CD). We not liable for loss of data and consequential damages. This product is designed to run on a PC/AT (IBM-compatible) computer with a free USB-port. Follow the safety instructions for the computer to which you are connecting the device. Never open up the component housings. This might lead to a shortcircuit or even a fire. Never allow children to use electronic devices unsupervised. Children may not always correctly identify potential hazards. Arrange the connection set so that no one can tread on or trip-over it. This device should only be repaired by an authorized service partner. Please contact customer service if you have any technical problems. Only a qualified engineer should perform upgrades and repairs. If you do not have the necessary qualifications, go to an appropriate Service Engineer. Please contact customer care if you are experiencing technical problems with this device. Keep the device away from moisture and avoid dust, heat and direct sunlight. Ensure an ambient temperature that is suitable for office equipment. Allow a clearance of at least 20 inches from sources of highfrequency and magnetic interference (TV, mobile telephone, infrared devices, loudspeaker cabinets, etc), in order to avoid malfunctions and loss of data. The clearance between the transmitter and the charging/slave station should be greater than 20 inches. Position and operate this device only on a stable, flat and vibrationfree surface. 3 Before cleaning the devices, remove the cable connection from the computer. Clean the devices and other components with a damp cloth. Do not use any solvents, corrosive or gaseous detergents. When connecting additional or other components the EMC (electromagnetic compatibility) directives must be adhered to. Do not operate the mouse when it is in the charger. The devices are not intended for use in a heavy industry environment. ERGONOMICS Medical studies have shown that certain physical ailments and injuries are linked to prolonged and repetitive movements in an unsuitable working environment and to bad working habits. Take frequent breaks when using a computer. If you experience pain, numbness or tingling in your arms, wrists, hands or fingers, consult a medical doctor. Remove the power plug of your computer from the power outlet and contact customer care: · · · · if if if if the connections are grazed or damaged; liquid has entered the device housing; a device does not operate correctly; a device is dropped or the housing damaged. INVENTORY Please check that these contents are complete and notify us within 14 days of purchase if any item is missing. The product you have purchased contains: Graphics tablet with USB cable set Pen* Wireless mouse* 2 batteries (AAA, 1.5 V) Installation and application software This user manual * ONLY for use with the Graphics tablet. 4 TECHNICAL DATA Active surfaces Maximum resolution Sensitivity Connection Environment temperature Humidity Mouse operating battery Pen operating battery Certification 9 x 12 in. (height x width) 3048 lpi / 120 lpmm 512 Steps USB 41° F ­ 104° F 20% - 80% (non- condensing) Microcells LR03 AAA type, 1.5V Microcells LR03 AAA Type, 1.5V CE, FCC, VCCI CI.II SYSTEM REQUIREMENTS Computer Processor performance Operating system RAM Hard disk storage Installation Connection PC/AT compatible computer Pentium class 200MHz or higher Windows® 98SE/ME/2000/XP 32 MB, 64 MB or more recommended at least 10 MB of free storage CD-ROM Drive USB USAGE With this Graphics tablet, new forms of graphics data input are available to you. The familiar ergonomics of the touch-sensitive pen allow you to draw directly into your Graphics program. You will be able to increase the efficiency of the input of your designs. Digitally, the drawing produced with the Graphics tablet, as always, can be further processed by specific digital imaging application software. The drawing pen has two buttons available, which can be programmed with the desired functions. The included cordless mouse offers you three programmable buttons for optimal functionality and control. 5 GETTING STARTED INSERT THE BATTERY INTO THE PEN + 1. Turn the rear end of the pen counterclockwise, as you would with a ballpoint pen, and remove the rear end. 2. Put one of the included batteries into the pen, (see above illustration). Make sure that the end of the battery marked with "+" appears at the pen top and that end marked with "- " points to the end of the rear contact spring 3. Replace the rear end of the pen again and turn it clockwise to tighten. INSERT THE BATTERY INTO THE CORDLESS MOUSE - + 1. Turn the mouse over and remove the battery compartment cover by using the small plastic tab (see arrow). Press carefully backwards and remove upwards. 2. Put one of the included batteries into the battery compartment of the mouse, (see above illustration). Make sure that the end of the battery marked with "+" appears on the right side and the end marked with "-" points to the rear contact spring. 3. Replace the battery compartment cover. It should lock into place. 6 USED BATTERIES - WASTE DISPOSAL Important note: Batteries are toxic and must be properly disposed of. Replace the empty batteries only with the same or an equivalent battery type. GRAPHICS TABLET DIAGRAM F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Functioning elements Operating display Function buttons Active surface Pen buttons Sensitive pen point Buttons of the remote mouse Graphics tablet connection cables USB Connection 7 INSTALLATION OF THE GRAPHICS TABLET The following installation instructions are applicable to the Microsoft® Windows® operating system versions 98SE/ME/2000/XP. The installation is basically the same with all of these operating systems. Here are some tips to complete the installation successfully. · Have ready the Installation CD for the Graphics tablet. · Also have ready the Installation CD of your computer's operating system in case you need it. · If you use Windows® 2000 or XP, login with administrator rights in order to successfully install the driver and software. During the installation procedure important files can be changed or even deleted. To avoid problems with using older files after installation, make sure you back up your hard disk and important files. Note: If your operating system is configured so that the installation procedure accepts only signed drivers and software (the default) this information screen will appear: Although the software lacks the digital signature it still works properly. Click on "Tell me why this testing is important" to get detailed information. Confirm by clicking on "Continue Anyway". 8 DRIVER INSTALLATION 1. Follow the guidelines in the chapter "Safety and Maintenance" (from page 2). 2. Place the PC, the Graphics tablet, the pen and the mouse on your work surface so that you can work comfortably and safely with them. 3. Switch on the computer and all the connected peripherals (monitor, printer, external modem etc.), and wait until the operating system has been fully started. 4. Locate a free USB port on your computer. 5. Connect the end of the USB cable ( ) with a free USB port on your computer ( ). 6. The operating system should now recognise the Graphics tablet. The operating system may request that you insert its installation disc at this time. 7. After the operating system has recognized the USB device, insert the Graphics tablet Installation CD in order to start the software installation routine. The green LED of the Graphics tablet (page 7, ) shows the system is working correctly. If the mouse and/or the pen are near the Graphics tablet, the LED glows steadily. The LED blinks if the pen and/or mouse are not within reach. DO NOT use the mouse and the pen simultaneously. 9 Note: If the CD does not start automatically, it is likely that the CD Autorun function has been deactivated. Read the respective chapter in Windows Help on how to activate this function. What follows is an example of a manual installation without the CD Autorun function: 1. Click on (Or hit and select the item + R to launch the corresponding dialog). 2. Now enter the letter of the CD-ROM drive followed by a colon and the program name setup: 3. Click on "OK". 4. Follow the instructions given by the setup program. 8. A window now appears with which you can start the driver's installation. Click on the USB Tablet Driver icon and follow the instructions on screen. INSTALLATION OF THE APPLICATIONS In order for you to be able to use your Graphics tablet optimally, we have enclosed application software. 1. If you have already installed the driver (see previous pages), you can now install the application software. 2. Select the required application from the program window of the CD. If the window is no longer visible, simply insert the CD again. 3. Follow the program's installation instructions. 4. After a successful installation, you can find the new programs in the Start menu under Programs. Restart the PC in order to fully complete the installation. 10 UNINSTALLING APPLICATIONS In order to remove the installed software from your PC, follow the steps below: 1. 2. Click on Click on 3. Finally, double click on the following icon: Select the appropriate program from the list, start the uninstallation and follow the instructions on screen. CONFIGURING THE GRAPHICS TABLET Click on Click on Double click on the Pad 9570 icon in order to configure the Graphics tablet. You may need to click Switch to Classic View on the upper left portion of the screen in order to reveal the Pad 9570 icon. This screen is where you can configure the individual buttons of the pen and mouse. You can also adjust the sensitivity of the Graphics tablet and choose a unit of measurement. CALIBRATING THE DRAWING PEN In order to improve the accuracy of your drawing pen, you should first make sure that it is properly calibrated with your Graphics tablet. 1. Follow the instructions above to open the Graphics tablet configuration screen. 2. Select the Control tab. 3. Under Tracking Mode select Pen Absolute. 4. Click once with the mouse in the grey box. 5. Use the drawing pen to tap the top left corner of the Graphics tablet. 6. Use ...