User manual MELICONI GUMBODY FACILE LIGHT

GB FACILE Light Thank you for choosing a MELICONI remote control. The F A C I L E L i g h t replacement remote control was designed as a TV control. Thanks to its large database and numerous functions it is ideal for replacing any lost, defective or broken remote control. Its ergonomic form and casing in soft rubber make it easy to grip and protect it against falls and bumps. The large pushbuttons are easy to see and to use. And thanks to the LIGHT button the keys light up so you can use the remote control even in the dark. Keep your Instruction Booklet and Code Booklet for future reference. For anyone with internet, via the website www.gumbodylight.com, it is even easier and quicker to programme the remote control and discover all the potential of the FACILE Light thanks to the on-line guide. USING THE KEYS AND FUNCTIONS The functions described below are only available if they are already foreseen by your TV. Light indicator TV ON/OFF button Teletext keys Number keys To select an external input terminal Control the volume using +/­ To select the next (P+) or previous (P-) channel or programme MUTE key turns the volume on and off Fastext functions or to select submenus by means of the colours To move around within the MENU or to control BRIGHTNESS/COLOUR Confirm button Key with additional TV functions To access the MENU LIGHT button to light up the keys Impact-proof rubber casing SET-UP Read these instructions carefully before programming your remote control! 7 FITTING THE BATTERIES Before programming and using the remote control, fit the batteries. The remote control requires 2 new AA/LR06 batteries. Insert the batteries as shown: · Remember to replace the batteries once a year. · If the light indicator starts to flash while using the remote control, replace the batteries. The batteries are low. · When you remove the batteries, fit the new ones within 5 minutes or you may have to reprogramme your remote control. · Make a note of the code for your TV on the adhesive label inside the battery cover in case you have to reprogramme your remote control. To programme the F A C I L E L i g h t remote control, follow the indications in paragraph A , B or C . A BRAND SEARCH PROGRAMMING MODE The quickest and easiest way to programme the remote control is by consulting the website www.gumbodylight.com. 1. Switch on the TV. 2. Look for the brand of your TV in the code book and make a note of the code indicated alongside (e.g. PHILIPS 0025) or the code for the brand indicated by the arrow. 3. Hold down the MUTE and ON/OFF buttons together for 5 seconds until the light indicator at the top starts to flash indicating that the remote control is being programmed. 4. Release the buttons and enter the brand code previously identified (e.g. 0025) within 12 seconds. The light indicator flashes more quickly to indicate that the remote control is ready for the search. 5. Point the remote control at the TV. Press and slowly release the ON/OFF key several times, stopping when the TV goes off. 6. When the TV goes off, press the OK key to confirm. Three flashes indicate that the operation has been completed correctly. PHILIPS PHONOLA 0025 PHILIPS + 5 SEC. + + + ADDITIONAL CHECK Check that some of the other keys, corresponding to those on your original remote control, work correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case, repeat the search procedure starting from point 3, entering the code previously used (e.g. 0025). 8 To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph CURRENT CODE DISPLAY. N.B. THE LIGHT INDICATOR STOPS FLASHING The remote control exits programming mode and the light indicator stops flashing: · if no keys are pressed for 14 seconds · if an invalid brand code is entered · if the end of the code search list has been reached. In this case, switch to programming mode C . B DIRECT CODE ENTRY The quickest and easiest way to programme the remote control is by consulting the website www.gumbodylight.com. 1. Switch on the TV. 2. Look for the brand of your TV in the code book and make a note of the first code in the list (e.g. Philips 1000). PHILIPS TV 1000 1009 1010 1014 1015 1006 1011 1016 1007 1012 1017 0025 1008 1013 1018 3. Hold down the MUTE and ON/OFF buttons together for 5 seconds until the light indicator at the top starts to flash indicating that the remote control is being programmed. 4. Release the buttons and enter the 4-digit brand code previously identified (e.g. 1000) within 12 seconds. Three flashes indicate that the code has been memorized correctly. If not, try the code entry procedure again, starting from point 3. 1 + 5 SEC. + 0 + 0 + 0 ADDITIONAL CHECK Point the remote control at the TV. Check that the TV responds correctly to the commands given. If there is no response or the TV only responds partially or incorrectly, it is probable that you have used the wrong code. In this case, repeat the procedure starting from point 3. This time, however, use the NEXT CODE in the list (e.g. 1006). Remember to make a note of the TV code used to programme the remote control on the adhesive label inside the battery cover for quick and easy reprogramming. N.B. THE LIGHT INDICATOR STOPS FLASHING The remote control exits programming mode and the light indicator stops flashing: · if no keys are pressed for 14 seconds · if an invalid code is entered 9 C GLOBAL SEARCH REMOTE CONTROL PROGRAMMING This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming the remote control by means of the other methods. The quickest and easiest way to programme the remote control is by consulting the website www.gumbodylight.com. 1. Switch on the TV. 2. Hold down the MUTE and ON/OFF buttons together for 5 seconds until the light indicator at the top starts to flash indicating that the remote control is being programmed. 3. Release the keys and enter the code 0000 within 12 seconds. The light indicator flashes more quickly to indicate that the remote control is ready for the search. 4. Point the remote control at the TV. Press and slowly release the ON/OFF key several times, stopping when the TV goes off. 5. When the TV goes off, press the OK key to confirm. Three flashes indicate that the operation has been completed correctly. + 5 SEC. 0 + 0 + 0 + 0 ADDITIONAL CHECK Check that some of the other keys, corresponding to those on your original remote control, work correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case, repeat the search procedure starting from point 2. To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph CURRENT CODE DISPLAY. N.B. THE LIGHT INDICATOR STOPS FLASHING The remote control exits programming mode and the light indicator stops flashing: · if no keys are pressed for 14 seconds · if the end of the code search list has been reached. In this case, consult our website www.gumbodylight.com 10 CURRENT CODE DISPLAY To find out the code of your remote control, follow this procedure: 1. Hold down the MUTE and ON/OFF keys together for 5 seconds until the light indicator at the top starts to flash. 2. Release the MUTE and ON/OFF keys and press and release the 1-/-- key within 8 seconds. 3. After a few seconds, the light indicator produces 4 series of flashes, with a pause between each series, corresponding to the current code. Count the number of flashes; each series of flashes corresponds to one figure in the code. 10 flashes correspond to 0. 4. Make a note of the code on the adhesive label inside the battery cover for quick and easy future reprogramming. ........................................................ = 1 ............................................ = 3 =0 .......................... = 6 Code obtained = 1306 + 5 SEC. N.B. this operation cannot be interrupted and the remote control cannot therefore be used until the end of the 4 series of flashes. LIGHT FUNCTION: Lights up the keys on the remote control Press the LIGHT button to light up the remote control keys. This is very useful in the dark to find which key to press. The light goes out when the LIGHT button is pressed again or after about 10 seconds if no keys are pressed. HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD Although not indicated on the keypad, some keys can be used for additional commands. Find them on your F A C I L E L i g h t remote control by pressing the buttons one by one and discovering the commands that interest you. In particular, the additional functions most frequently used, such as NORMALIZATION, COLOUR and BRIGHTNESS, can be found on the following keys: Normalization: Brightness (+): or Brightness (-): or Colour (+): or Colour (-): or For less frequently used functions look for the additional commands on our website www.gumbodylight.com. As well as easily finding the code to programme your remote control, the on-line guide will help you to find which keys on the F A C I L E L i g h t remote control correspond to the additional commands. 11 PROBLEM SOLVING PROBLEM The TV does not respond and the light indicator does not light up when a key is pressed. SOLUTION Try some of the other frequently-used buttons. If the problem persists, check that the batteries are fitted correctly. If necessary, replace them with 2 new 1.5 V AA/LR06 batteries. Check that the batteries are new and that the remote control is pointing at the TV without any obstacles in the way. If necessary, re-enter the remote control code, following the programming procedure A or B or C . The batteries are low. Change them. The TV does not respond but the light indicator does light up. The light indicator flashes when a key is held down but the TV does not respond. The remote control commands are not all working correcting. The code for your TV brand is not in the Code Book. You may have used the wrong code. Re-enter the remote control code, following the programming procedure A or B or C . Programme the remote control following the global search procedure C or consult the on-line guide on the website www.gumbodylight.com to find the code with which to programme your remote control. INFO-LINE If you have any queries about your F A C I L E L i g h t remote control: · read this Instruction Booklet carefully - you will find an answer to most of your questions · consult our website www.gumbodylight.com where you will find the answers you need easily and quickly. WARRANTY: 2 years The warranty ceases to be valid if the product is tampered with or used incorrectly. Type of remote control GumBody Light Model FACILE Light Purchase date / / Dealer's stamp The symbol of the crossed trash can shown on the remote control indicates that once the product has reached the end of its working life it should be disposed of separately from other waste. The user should, therefore, take the remote control to a specialised collection centre for electronic and electrical waste, or hand it over to the dealer when purchasing a new similar remote control, on a one to one basis. Correct separated collection for subsequent recycling, processing and environmentally compatible disposal contributes in preventing possible negative effects on the environment and on health and favours the recycling of the materials used in producing the remote control. Improper disposal of the product by the user leads to application of the penalties as per legislative decree no. 22/1997 (article 50 and following of decree no. 22/1997). 12