istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 5 GB Thank you for choosing MELICONI. This simplified universal remote control contains all the main functions of most TV and digital terrestrial and/or satellite decoder (STB) remote controls. Before programming and using the remote control, fit the batteries. Keep your Instructions and Code Booklet for future reference. USING THE KEYS AND FUNCTIONS To select the next program or to turn ON your TV. Light indicator. Mute key. Control the volume using +. Control the volume using -. To select the previous program or to turn ON your TV. Numeric keypad. To select an external input terminal. Selection key to control the TV. Teletext keys: to access Teletext close Teletext and return to normal viewing Selection key to control the decoder. ON/OFF key to turn the appliance off, or in some cases on. FITTING THE BATTERIES Before programming and using the remote control, fit the batteries. The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown. · The batteries must be changed once a year. · Change the batteries if the light indicator starts to flash during use. The batteries are low. · This remote control has a permanent memory and does not lose the programmed codes when the batteries are removed. · Make a note of the code for your TV on the adhesive label supplied inside the battery cover. This note will be handy if you have to reprogram your remote control. SET-UP Read these instructions carefully before programming your remote control! To command your appliances, you must program your Speedy 210 STB as described in paragraphs A or B below. Visit out Internet site www.meliconi.com for interactive instructions for easy and fast remote control programming. Warning: programme one appliance at a time. 5 istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 6 A HOW TO PROGRAMME THE REMOTE CONTROL 1. Turn on the appliance to be programmed and select a programme. 2. Look for your TV brand in the list of codes at the end of this booklet and make a note of the corresponding code indicated alongside (e.g. Philips 0025). If your TV brand is not listed, apply the global search described in paragraph B. 3. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down for five seconds until the light indicator at the top starts flashing to indicate that the remote control is programming. 4. Release the keys, Within 15 seconds, enter the brand code previously identified (e.g. 0025). The light indicator flashes more quickly to indicate that the remote control is ready for the search. 5. Point the remote control at the appliance. Press and release the key slowly several times and stop when the appliance goes off (you may have to press the key dozens of times). 6. When the appliance goes off, press the key to confirm. Three long flashes indicate that the operation has been completed correctly. Additional check Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar but different remote control. In this case, repeat the search procedure from point 3. Identify the code and make a note of it following the code noting procedure (see "PROGRAMMED CODE NOTING" section). NOTE: during the search operation, the light indicator flashes more quickly. The light indicator stops flashing and the remote control leaves the programming mode in the following cases: · if no keys are pressed for 12 seconds · if the code search list is completed. In this case, switch to programming mode B B GLOBAL SEARCH REMOTE CONTROL PROGRAMMING This operation may take a few minutes. 1. Turn on the appliance to be programmed and select a programme. 2. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down for five seconds until the light indicator at the top starts flashing to indicate that the remote control is programming. 3. Release the keys. Within 15 seconds, enter the code 0000. The light indicator flashes more quickly to indicate that the remote control is ready for the search. 4. Point the remote control at the appliance. Press and release the key slowly several times. Stop when your appliance goes OFF (you may have to press the key over a hundred times). 5. When the appliance goes off, press the operation has been completed correctly. key to confirm. Three long flashes indicate that the Additional check Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar but different remote control. In this case, repeat the search procedure from point 2. 6 istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 7 Identify the code and make a note of it following the code noting procedure (see "PROGRAMMED CODE NOTING" section). NOTE: during the search operation, the light indicator flashes more quickly. The light indicator stops flashing and the remote control leaves the programming mode in the following cases: · if no keys are pressed for 12 seconds. · if the code search list is completed. In this case, visit www.meliconi.com PROGRAMMED CODE NOTING Always write down the 4-digit codes for your remote control on the label inside the battery cover after running the search and saving the codes. This may be useful if you need to reprogram your remote control in the event of accidental cancellation. To find the codes for your remote control: 1. Hold the selection key whose code you are looking for down for five seconds until the light indicator at the top starts flashing to indicate that the remote control is programming. 2. Release the selection key ( or ) and then press and release the key within eight seconds. 3. After a few seconds, the light indicator communicates the code you are looking for by flashing the four numbers separately. Count the number of flashes for each code number. For example, for the code 1306, the key flashes one, three, ten and six times to give: =1 =3 =0 =6 4. Note this code on the label inside the battery cover, for rapid consultation. RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN 1. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down for five seconds until the light indicator at the top starts flashing to indicate that the remote control is programming. 2. After releasing the keys enter the code number you noted down previously. Three flashes indicate that the code has been saved correctly. If not, try the code entry procedure again from point 1. TV FUNCTIONS ALWAYS ACTIVE The MUTE, VOLUME -, VOLUME + keys can also be used to control the decoder. To use these functions on the digital decoder, press the corresponding key while holding the STB key down at the same time. 7 istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 8 TROUBLESHOOTING PROBLEM The appliance does not respond and the light indicator does not light up when you press a key. The appliance does not respond but the light indicator lights up. SOLUTION Check that the batteries are fitted correctly. If necessary, replace them with 2 new 1.5 V AAA/LR03 alkaline batteries. Check that the batteries are new and that the remote control is pointing at the appliance without any obstacles in the way. If required, reset the remote control code, following the programming procedure A or B . The batteries are low. Change them. When a key is pressed, the light indicator flashes and the appliance does not respond to the commands. The remote control commands are not all working correcting. The code for your appliance brand is not in the list of codes of the end of this booklet. You may have used the wrong code. Reset the remote control code, following the programming procedure A or B . Set the remote control code, following the global search programming procedure B . INFO LINE If you have any queries about Speedy 210 STB: · read this booklet carefully­ this will help you to solve almost all problems · consult our Internet site www.meliconi.com to answer all your queries more easily and quickly. WARRANTY: 2 years The warranty ceases to be valid if the product is tampered with or used incorrectly. Remote control model Purchase date Speedy 210 STB Agent's stamp 8 ...