FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/ 1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) P/N: 219-20-990255 i Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. " Energy Star Notice As an ENERGY STAR Partner, Microtek International, Inc. has determined that this monitor meets the ENERGY STAR guidelines for energy efficiency. ii Table of Contents Introduction 1 Product Features .................................................................... 1 Unpacking .............................................................................. 2 Precautions ............................................................................ 2 Cleaning ................................................................................. 3 Installation 4 Installing the Monitor ............................................................ 4 Connecting the Monitor ........................................................ 5 Connecting the Audio cable ........................................... 6 Adjusting the Viewing Angle ................................................ 7 Operating the Monitor 8 How to Use the OSD ............................................................. 8 Operating Procedure ....................................................... 9 Adjusting Monitor Display .................................................. 10 Auto Adjustment ........................................................... 10 Manual Adjustment ....................................................... 1 1 Adjustment Lock .................................................................. 12 Resetting All Adjustment ..................................................... 12 OSD Function Menus .......................................................... 13 SCREEN Menu .............................................................. 13 GAIN CONTROL Menu .................................................. 13 COLOR Menu ................................................................. 14 MODE SELECT Menu .................................................... 14 Other Related Settings ........................................................ 15 Adjusting the Backlight ................................................ 15 Adjusting Volume .......................................................... 15 Setting GAMMA ............................................................ 16 Installing the Arm 17 iii Appendixes A: Specifications ................................................................. 19 B: Supported Timing ........................................................... 20 C: Troubleshooting .............................................................. 21 D: Power Management ........................................................ 23 E: DDC (Plug and Play) ........................................................ 23 F: For Your Safety ................................................................ 24 iv Introduction Congratulations on the purchase of your new Microtek LCD monitor! Providing a maximum resolution of 1280 x 1024 pixels with a flicker-free display at up to 75Hz refresh rate, your LCD monitor offers sharp and vibrant color display without the radiation emission and hazards associated with CRT monitors. Product Features · 17.0" TFT active matrix color crystal displays, Dot pitch 0.264 mm · Supports SXGA resolution of 1280 x 1024 pixels · Wide viewing angle · Wide tilting angle · VESA DPMS-compliant power saving: Automatically powers down the monitor after a defined period of inactivity · Digital character smoothing · Automatic setup · Compatible with Windows and Macintosh · Easy-to-use OSD (On-Screen Display) · Plug & Play: Conforms to VESA standards and supports DDC 2B specifications · Multiscan functions of SXGA 1280 x 1024, Quad-VGA 1280 x 960, XGA 1024 x 768, SVGA 800 x 600, VGA 640 x 480, 1152 x 870, 1152 x 864, 832 x 624, 720 x400, and 640 x 400 for precision graphics performance · Extra-slim design to maximize your desk space · Includes built-in speaker 1 Unpacking Before unpacking your LCD monitor, prepare a stable, level, and clean surface near a wall outlet for your LCD monitor. 1. Set the LCD monitor box in an upright position and open from the top of the box before removing the right/left cushions. 2. Check to see that you have the following accessories shown below: User's Manua l VGA Cable Audio Cable Power Cord User's Manual NOTE: Remember to save your original box and packaging material in case you need to transport or ship the monitor. Precautions · Read all of these warnings and save the manual for later use. · Follow all warnings and instructions on the product. · Do not cover or block the vent holes in the case. · Do not insert sharp objects or spill liquid into the LCD monitor through the cabinet slots, as this may cause accidental fire, electric shock or failure. · Disconnect the power plug from the AC outlet if you are not going to use the monitor for an extended period of time. · Do not attempt to service this product yourself, as opening or removing the cover may expose you to dangerous voltage or other risks. · Do not touch the screen directly. Oil from your skin may damage the screen, and is difficult to remove. · Do not apply pressure to the screen, as the screen is very delicate. · Keep the monitor away from extremely hot, cold or humid places. 2 · Do not place the monitor directly under sunlight, in dusty surroundings, or near equipment which may generate strong magnetic fields. Cleaning Warning: If you drop any material or liquid such as water onto the monitor when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable. Caution: · For safety reasons, turn off the power switch and unplug the monitor before cleaning. · Do not scratch or rub the screen with a hard object. · Never use any of the following solvents on the LCD monitor: Thinner; spray-type cleaners; benzene; wax; abrasive cleaners; and acid or alkaline solvents. Such harsh chemicals may cause damage to the cabinet and the LCD screen. · Rubbing the cabinet with products made of rubber or plastic for prolonged periods may cause degeneration or loss of paint on the cabinet. Cabinet · Remove dirt with a lightly moistened cloth and a mild solvent detergent. Then wipe the cabinet with a soft dry cloth. LCD · Periodic cleaning with a soft dry cloth is recommended. · Do not use tissue to clean the screen, as this may damage the LCD screen. 3 Installation Installing the Monitor · DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as fire, electric shock or damage may ensue. · DO NOT place your LCD monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight. · MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire. · PLACE the monitor at least 4 inches (10 cm) away from the walls · SAFE storage temperature of the LCD monitor is in a range of ­4ºF to +149ºF (-20ºC to +65ºC). 4 Connecting the Monitor Warning: Do not operate the LCD monitor with unspecified power supply. Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. 1. Turn off your computer and LCD monitor. 2. Take out the monitor and place on the table. 3. Connect one end of the VGA cable to your monitor's analog RGB input port, and connect the other end of the cable to the computer's analog RGB output port. Make sure the cables are securely connected. VGA cable 4. Plug the Power cord into the back of the monitor, and plug the other end into a power source (power surge protector highly recommended). 5 5. Turn on the LCD monitor. The power LED lights up orange. 6. Turn on your computer. The power LED changes from orange to green when the monitor detects the input signal source from the computer. At the same time, the image to be displayed appears on the screen. A conversion adapter (not supplied) may be required if you connect the monitor to the Apple Power Macintosh-series computer. The conversion adapter should be installed with the correct orientation as shown in the illustration. Conversion adapter Connecting the Audio cable With a built-in speaker feature, the monitor allows you to view images with audio. Connect one end of the Audio cable (supplied) to your monitor's audio input port, and connect the other end of the cable to the computer's audio output port. 6 Adjusting the Viewing Angle Your LCD monitor is designed to allow adjustment for optimal viewing angles. You can adjust the monitor upward to 20 degrees and downward to 5 degrees. The monitor can also be turned clockwise/counterclockwise to 45 degrees. Vertical Adjustment Pan Swivel Angle Left: 45° / Right: 45° Tilt Angle Tilt Back: 20° / Tilt Front: 5° NOTE: Do not touch the screen while changing the viewing angle, as this may damage the screen. In addition, make sure your fingers do not get caught in any of the monitor's parts while adjusting the viewing angle. 7 Operating the Monitor The LCD monitor has been preset at the factory with the Timing shown in the section "Appendix B" to achieve optimal display. You can adjust the display to the desired brightness and sharpness by following the instructions. Buttons AUTO MENU / MODE Description Automatically adjusts monitor settings to the best visual quality Displays/Exits the OSD screen or selects the OSD menu Selects the OSD function items · Indicates cursor movement, or increases/decreases the values of a setting when manually operating the OSD · Adjusts the brightness of the backlight (darker or lighter) · Adjusts the volume up or down Power LED status Speaker Turns the monitor ON/OFF Green ­ Normal operation Orange ­ Power Management Provides audio playback via the external device connected to the monitor 8 How to Use the OSD (On-Screen Display) The OSD (On-Screen Display) lets you easily adjust the various settings for your LCD Monitor to desired levels of performance. The OSD includes various function menus (SCREEN, GAIN CONTROL, COLOR, and MODE SELECT). You can toggle through these OSD function menus by pressing the MENU button. Operation Procedure The buttons on the bottom of the monitor are used to navigate the OSD. Follow the sequence below to do the following: toggle through the OSD function menu, select the function item, adjust the setting, save or cancel th ...